- DL manuals
- Icom
- Transceiver
- IC-F510
- Instruction Manual
Icom IC-F510 Instruction Manual
Summary of IC-F510
Page 1
If610 uhf transceiver instruction manual if510 vhf transceiver.
Page 2
R warning! Never connect the transceiver to an ac outlet. This may pose a fire hazard or result in an electric shock. R warning! Never connect the transceiver to a power source of more than 16 v dc such as a 24 v battery. This connection will ruin the transceiver. R warning! Never cut the dc power c...
Page 3
Do not operate the transceiver without running the vehi- cle’s engine. The vehicle’s battery will quickly run out if the transceiver is in transmission while the vehicle’s engine off. Do not place the transceiver in excessively dusty envi- ronments. Do not place the transceiver against walls. This w...
Page 4: Front Panel
R e w q u y t n front panel q af volume control knob ➥ rotate the knob to adjust the audio output level. • minimum audio level is pre-programmed. W left up/down [ y ] / [ z ] keys ➥ one of several functions can be programmed by your dealer. (same as [p0] to [p4] keys) e function display ➥ displays v...
Page 5: Function Display
T dealer-programmable keys [p0] to [p4] ➥ desired functions can be programmed independently by your dealer. Y power switch [power] ➥ push to turns the power on and off. • the following functions are available at power on as options: - automatic scan start - password prompt - set mode u microphone co...
Page 6: Programmable Function Keys
U scrambler indicator ➥ appears when scrambler function is activated. (optional ut- 109 (#02)/ut110 (#02) scrambler unit is required.) i 2/5tone indicator ➥ appears when specified 2/5tone call is received. O alphanumeric display ➥ displays the ch number, 5-tone indication, dtmf num- bers, audible in...
Page 7
4 1 panel description priority channel keys ➥ select priority a or priority b channel with each push. ➥ push and hold [ pri a] (rewrite) to reassign the operating channel as priority a channel. Scan start/stop key ➥ push this key to start scanning; and push again to stop. Note: place the microphone ...
Page 8
5 1 panel description rx speaker key push to turn the rx speaker function on or off. When the rx speaker function is turned on, the received audio can be heard via the exter- nal speaker that is connected to the d-sub 25- pin. • this function is available when the external speaker is additionally co...
Page 9
6 1 panel description emergency key push and hold to transmit an emergency call. • if you want to cancel the emergency call, push (or push and hold) the key again before transmitting the call. • the emergency call is transmitted one time only or repeatedly until receiving a control code depending on...
Page 10
Mic compander key push to toggle the mic compander function on or off. Hook scan key when the on hook scan function is activated, push this key to stop scanning temporarily. Push this key again to re-start scanning. User set mode key changes the contents of the items in the user set mode. • push and...
Page 11: Operation
8 2 operation n turning power on q push [power] to turn the power on. • a power-up alert tone sounds for about 1 sec. And an opening message may appear. W if the transceiver is programmed for a start up passcode, input digit codes as directed by your dealer. • the keys in the table below can be used...
Page 12: Receiving and Transmitting
N receiving and transmitting receiving: q push [power] to turn the power on. W push [ ] or [ ] to select a channel. E when receiving a call, adjust the audio output level to a comfortable listening level. Transmitting: q take the microphone off hook. • 5-tone mute may be released (the ‘audible’ cond...
Page 13
10 2 operation d tx code channel selection if the transceiver has a [tx ch] key, display can be toggled between the operating channel number (or name) and tx code channel number (or name). When the tx code channel number (or name) is displayed, the [ ] or [ ] keys select the tx code channel. Using [...
Page 14
11 2 operation d dtmf transmission if the transceiver has a [dtmf] key, the automatic dtmf transmission function is available. Up to 7 dtmf channels are available. Q push [dtmf] — a dtmf code channel appears. W push [ ] or [ ] to select the desired dtmf channel. E push and hold [dtmf] to transmit th...
Page 15
12 2 operation d user set mode user set mode is accessed at power on and allows you to set seldom-changed settings. In this case you can “custom- ize” transceiver operation to suit your preferences and operat- ing style. Entering the user set mode: q while pushing and holding [ ] and [ ] , push [pow...
Page 16: Rear Panel and Connection
Solder crimp note: use the terminals for the cable connections. + q optional speaker (sp-22) r t e supplied dc power cable w 12v battery red: black: antenna optional cable (opc-617) r warning! Never re- move the fuse-holder from the dc power cable. R warning! Never con- nect to a 24 v battery. N rea...
Page 17: Supplied Accessories
Q antenna connector connects to an antenna. Ask your dealer about antenna selection and placement. W microphone hanger connect the supplied microphone hanger to the vehicle’s ground for microphone on/off hook functions. (see p. 2) e dc power receptacle connects to a 12 v dc battery. Pay attention to...
Page 18: Mounting The Transceiver
N mounting the transceiver the front panel can be inverted for correct viewing while leav- ing the built-in speaker facing away from the mounting sur- face. D inverting the front panel q unscrew the 2-side screws. W detach the front panel forward from the transceiver. E bent the flat cable between f...
Page 19
D mounting the transceiver the universal mounting bracket supplied with your transceiver allows overhead mounting. • mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1.5 kg. Spring washer flat washer nut 16 3 connection and maintenance.
Page 20: Optional Ut-108 Installation
N optional ut-108 installation the optional ut-108 unit install as follows: q turn power off, then disconnect the dc power cable. W unscrew the 4 screws, then remove the bottom cover. E install the unit as shown in the diagram below. R replace the bottom cover and screws, then the dc power cable. N ...
Page 21: Antenna
N antenna a key element in the performance of any communication sys- tem is an antenna. Ask your dealer about antennas and the best places to mount them. N fuse replacement two fuses are installed in the supplied dc power cable. If a fuse blows or the transceiver stops functioning, track down the so...
Page 22: Options
Sp-22 external speaker compact and easy-to-install. Input impedance : 4 ø max. Input power : 5 w hm-152/hm-152t/hm-148g/hm-148t hand microphones • hm-152 : hand microphone • hm-152t : dtmf microphone • hm-148g : self ground heavy duty microphone • hm-148t : self ground heavy duty dtmf microphone the...
Page 23: 0168
Declaration of conformity we icom inc. Japan 1-1-32, kamiminami, hirano-ku osaka 547-0003, japan kind of equipment: uhf transceiver this compliance is based on conformity with the following harmonised standards, specifications or documents: i) en 300 279 (february 1999) ii) en 60950 august 1992, a11...
Page 24
1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan a-6121h-1eu- u printed in japan © 2001–2009 icom inc. Ger aut gbr irl fra ned bel lux esp por ita gre swe den fin sui.