Jablotron JA-60GSM Installation Manual - page 7
JA-60GSM communicator module
- 7 -
MFJ51212
4.2.2
Editing of remote control SMS commands
If you change any of the text strings from 703 to 711, the dialer will
recognize the new text string as the valid remote control command.
E.g., if you change text “
MO
” (number 705) to “
Tell me my alarm
status please
” it will be possible to read the control panel status by
sending the new string as the SMS command. This function helps
customers keep the commands secret and protect the dialer against
unauthorized operation.
4.3 Assignment of audible warnings to be reported
Table 4.3.1 shows the complete list of all possible events in the alarm
system. It also shows which events are assigned to which telephone
numbers to be reported audibly. You can make your own setting by:
82 uu t y
where
uu
is an event index from 01 to 31
t
is a telephone number memory location from 1 to 8
y
0
= reporting disabled,
1
= reporting enabled
4.3.1
Table – audible warning assignments to telephone numbers
The
x
marks in the table show which events are assigned to which telephone numbers to be reported audibly. If you modify these, we recommend you
mark your setting in the table. If there is an alarm, a siren sound will be played, for other events a melody sound will be played.
Telephone numbers
Event index uu
Event
1
2
3
4
5
6
7
8
01
Intruder alarm – instant zone
x x x x x
02
Intruder alarm – delayed zone
x
x
x
x
x
03
Fire alarm
x
x
x
x
x
04
Panic alarm
x
x
x
x
x
05
Wrong access code alarm
x x x x x
06
Alarm after power on
x
x
x
x
x
07
Tamper
alarm
x x x x x
08
Tamper
OK
09
Alarm end
10
Alarm canceled by a user
11
Arming
12
Disarming
13
Partial arming (Home)
14
No code arming
15
External communication failure
16
External communication recovery
17
Failure
18
Failure recovery
19
AC failure longer than 30 minutes
20
AC
failure
21
AC
recovery
22
Battery
failure
23
Battery recovery
24
Enter programming mode
25
Exit programming mode
26
Remote
access
27
Remote access – end
28
RF
jamming
29
Internal communication failure
30
Internal communication recovery
31
Periodic
test
Example: if you enter 820381 and a Fire alarm is triggered (event index 03) the dialer will call the 8
th
telephone number and it will play audible warning if
the call is answered.
4.4 Temporarily disabling SMS and audible reports
If you need to disable all SMS and audible reports temporarily to all
telephone numbers, use the following sequence:
800 all reports disabled
the communicator will send
neither the alarm SMS nor acoustic warnings
801 all reports enabled
the communicator will send the
audible reports and SMS messages according to the settings
in chapter 4.1.1. and 4.3.1.
802
the communicator will send the preset reports except the
events of "arming" and "disarming" by Master code, user codes 1 to
4 and controllers 1 to 4
Default setting:
all reports enabled (801).
5 General
settings
Enter programming mode if you are going to use any of the following
sequences.
5.1 Using a SIM card with a PIN code
It is recommended to use a SIM card with the PIN code protection
disabled (this can be done with a mobile phone, see section 1). If you
insist on using a PIN code, enter it after the GSM dialer has been
powered up using:
70 xxxx F0
where:
xxxx
is the PIN code (4 digits)
Example: if the PIN code is 1234 enter 701234F0
Default setting: 70F0 the PIN code protection is off
Note:
If the dialer does not connect to the GSM network after
powering up (LED starts flashing), there is a probability that a
wrong PIN code was set. In this situation:
o
enter 70F0 on the control panel keypad when in programming
mode (PIN code erasing in the dialer)
o
disconnect the control panel’s power supply (AC and battery)
o
remove the SIM card, insert it into a mobile phone and check
the PIN code. Check also that it is possible to connect to the
desired GSM network at the location of the dialer’s GSM
antenna.
o
if you are sure the PIN code is right and the location is covered
by a GSM signal, insert the SIM card back in to the dialer, switch
the power supply on, enter the PIN code (70 PIN F0) and wait
until the communicator connects to the GSM network (LED will
turn off).