1. DL manuals
  2. Jacobsen
  3. Lawn Mower
  4. Greens King IV Plus
  5. Safety & Operation Manual

Jacobsen Greens King IV Plus Safety & Operation Manual

Summary of Greens King IV Plus

  • Page 1

    When performance matters. ™ gb united kingdom greens king iv plus with rops 62304 – kubota d722-e3b engine warning warning: if incorrectly used this machine can cause severe injury. Those who use and maintain this machine should be trained in its proper use, warned of its dangers and should read the...

  • Page 2

    En-2 contents this manual contains safety and operating instructions for your new jacobsen machine. This manual should be stored with the equipment for reference during operation. Before you operate your machine, you and each operator you employ should read the manual carefully in its entirety. By f...

  • Page 3: Warning

    Safety 2 en-3 2 safety 2.1 operating safety ______________________________________________________ 1. Safety is dependent upon the awareness, concern and prudence of those who operate or service the equipment. Never allow minors to operate any equipment. 2. It is your responsibility to read this man...

  • Page 4: Warning

    2 safety en-4 2.2 important safety notes________________________________________________ this safety alert symbol is used to alert you to potential hazards. Danger - indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warning - indicates a poten...

  • Page 5

    Decals 3 en-5 3 decals 3.1 decals _________________________________________________________________ familiarize yourself with the following decals. They are critical to the safe operation of the machine. Replace damaged decals immediately. 4181864 4181865 rev b danger to avoid injury when working wi...

  • Page 6

    3 decals en-6 familiarize yourself with the following decals. They are critical to the safe operation of the machine. Replace damaged decals immediately. 4181863 warning read manual for service. Torsion spring under extreme tension. Clamp may turn suddenly. To avoid injury, unwind spring by tapping ...

  • Page 7: Important

    Decals 3 en-7 mélangez des quantités équivalentes d’eau propre et d’antigel à base d’éthylène glycol de haute qualité, afin de maintenir une protection contre le débordement par ébullition, la rouille et la corrosion. Vidangez et éliminez le liquide de refroidissement une fois par an. Lisez le manue...

  • Page 8: 105

    3 decals en-8 familiarize yourself with the following decals. They are critical to the safe operation of the machine. Replace damaged decals immediately. A b c d 2812066 8-12 p.S.I. (55-83 kpa) 105 db l wa 4141266 3-5 30 3009744 brake reel switches wiring tire pressure noise level engine oil pressur...

  • Page 9

    Decals 3 en-9 2 1 n r right reel center reel left reel reel forward rotation reel off reel reverse rotation parking brake disengaged transport mow neutral reverse traction lever parking brake engaged charging system fuse interlock system fuse.

  • Page 10: Warning

    4 controls en-10 4 controls 4.1 icons ___________________________________________________________________ warning never attempt to drive the mower unless you have read the safety and operation manual and know how to operate all controls correctly. Familiarize yourself with the icons shown above and ...

  • Page 11

    Controls 4 en-11 3-5 40 p s r 2 1 n r 10 12 14 16 t u w v x y z a b c e f g h j k l m n aa d a reel control lever b parking brake lever c traction lever d temperature gauge (diesel) e volt meter f ignition switch g mechanics (backlap) switch h light switch (optional) j lights fuse (optional) k charg...

  • Page 12: Warning

    4 controls en-12 4.2 control descriptions__________________________________________________ a. Reel control levers - used to operate the cutting units. Push lever(s) forward for forward rotation. Pull lever(s) back for reverse rotation. All three levers must be in off position to start engine. B. Pa...

  • Page 13: Caution

    Operation 5 en-13 5 operation 5.1 daily inspection ________________________________________________________ 1. Perform a visual inspection of the entire unit, look for signs of wear, loose hardware, and missing or damaged components. Check for fuel or oil leaks to ensure connections are tight and ho...

  • Page 14: Warning

    5 operation en-14 5.3 operating procedures ______________________________________________________ 1. Under no circumstances should the engine be started without the operator seated on the mower. 2. Do not operate mower or attachments with loose, damaged, or missing components. Whenever possible mow ...

  • Page 15

    Operation 5 en-15 5.4 starting________________________________________________________________ important: do not use starting assist fluids. Use of such fluids in the air intake system may be potentially explosive or cause a “runaway” engine condition and could result in serious engine damage. 1. Ma...

  • Page 16: Caution

    5 operation en-16 5.6 to drive / transport____________________________________________________ read and follow all safety notes contained in this manual when driving or transporting mower. Refer to section 5.3 for general operating instructions. When operating in reverse look behind you to ensure yo...

  • Page 17

    Operation 5 en-17 how to calculate a slope: tools required: level (a), either 1 yard, or 1 meter long. Tape measure (b). With the level (a) positioned horizontally, measure the distance (c) with tape measure (b). Use the chart to calculate either the slope angle or the % grade of the slope (d). Figu...

  • Page 18: Warning

    5 operation en-18 5.8 mowing_________________________________________________________________ operators should practice mowing in a clear area to become familiar with raising and lowering the reels. Practicing will help the operator become proficient at starting and stopping each pass within a foot ...

  • Page 19: Notice

    Operation 5 en-19 5.9 towing / trailering _____________________________________________________ if the mower experiences problems and must be shut down and removed from the area, it should be loaded onto a trailer for transport. If a trailer is not available, the unit can be towed slowly short dista...

  • Page 20: Notice

    5 operation en-20 5.10 daily maintenance _____________________________________________________ important: for more detailed maintenance information, adjustments, and maintenance/lubrication charts, see the parts & maintenance manual. 1. Park the mower on a flat, level surface. Fully lower the implem...

  • Page 21

    Quality of cut 6 en-21 6 quality of cut 6.1 quality of cut troubleshooting _______________________________________ it is recommended that a “test cut” be performed to evaluate the mower’s performance before beginning repairs. An area should be available where “test cuts” can be made. This area shoul...

  • Page 22

    6 quality of cut en-22 6.3 marcelling ____________________________________________________________ note: arrow indicates direction of travel. Marcelling, like washboarding, is a cyclical pattern of varying cutting heights, resulting in a wave-like cut appearance. In most cases, the wave tip-to-tip d...

  • Page 23

    Quality of cut 6 en-23 6.4 step cutting____________________________________________________________ note: arrow indicates direction of travel. Step cutting occurs when grass is cut taller on one side of a reel than the other or one cutting unit to another. This is usually caused by mechanical wear o...

  • Page 24

    6 quality of cut en-24 6.5 scalping _______________________________________________________________ note: arrow indicates direction of travel. Scalping is a condition in which areas of grass are cut noticeably shorter than the surrounding areas, resulting in a light green or even brown patch. This i...

  • Page 25

    Quality of cut 6 en-25 6.6 stragglers ____________________________________________________________ note: arrow indicates direction of travel. Stragglers are scattered blades of uncut or poorly cut grass. Probable cause remedy bedknife improperly adjusted. Adjust reel-to-bedknife setting. Dull reel o...

  • Page 26

    6 quality of cut en-26 6.7 streaks ________________________________________________________________ note: arrow indicates direction of travel. A streak is a line of uncut grass. This is usually caused by a nicked or bent bedknife. Probable cause remedy damaged bedknife. Replace bedknife. Damaged or ...

  • Page 27

    Quality of cut 6 en-27 6.8 windrowing ____________________________________________________________ note: arrow indicates direction of travel. Windrowing is the deposit of clippings concentrated at one end of cutting unit(s) or between two cutting units, forming a line in the direction of travel. Pro...

  • Page 28

    6 quality of cut en-28 6.9 rifling or tramlining __________________________________________________ 6.10 mismatched cutting units ______________________________________________ note: arrow indicates direction of travel. Rifling or tramlining is a pattern of varying cutting heights, resulting in a wa...

  • Page 29

    Notes 7 en-29 7 notes.

  • Page 32

    World class quality, performance and support equipment from jacobsen is built to exacting standards ensured by iso 9001 and iso 14001 registration at all of our manufacturing locations. A worldwide dealer network and factory trained technicians backed by genuine parts provide reliable, high-quality ...