P/n 24-156 rev a 7/00 page 1 jade convection oven installation, operation and maintenance instructions note: instructions must be posted in a prominent location, which will instruct the user in the event that he detects the smell of gas. This information shall be obtained from your local gas company...
P/n 24-156 rev a 7/00 page 2 table of contents gas specifications……………………………………….2 future oven information……………………………..3 installation instructions…………………………….3 delivery and inspection………………………3 location of oven………………………………...3 minimum clearance…………………………10,11 electrical connectios……………………...7,8 vent...
P/n 24-156 rev a 7/00 page 3 for future reference to operator, installer, user it is necessary to register model number and serial number for warranty service. Where can you find model number and serial number? (location of nameplate) insert -- diagram convection oven future oven information stop st...
P/n 24-156 rev a 7/00 page 4 natural gas propane gas us units si units us units si units gas inlet pressure (at manif.) 5” w.C. 1.25 kpa 10” w.C. 2.5 kpa oven input per burner per oven 20,000 btu/hr 80,000 btu/hr 5.9 kw 23.4 kw 20,000 btu/hr 80,000 btu/hr 5.9 kw 23.4 kw main office orifice size #47 ...
P/n 24-156 rev a 7/00 page 5 delivery and inspection: all jade range ovens are carefully inspected and packed, to prevent shipping damage. Upon delivery of your jade range oven: • inspect the shipping container for external damage • uncrate oven and check for concealed damage. It is the carrier’s fu...
P/n 24-156 rev a 7/00 page 6 insert picture convection oven.
P/n 24-156 rev a 7/00 page 7 radiant burner convected heat heat heat clearances/installation 1. For installation in fire-resistant locations only. 2. For installation with the following minimum clearances to combustible clearances: sides = 6 inches back = 3 inches 3. For installation with legs or ca...
P/n 24-156 rev a 7/00 page 8 warning! Electrical grounding instructions this appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong fro...
P/n 24-156 rev a 7/00 page 9 for an appliance equipped with casters: 1. The installation shall be made with a connector that complies with the standard for connectors for movable gas appliances, ansiz21.69 or connectors for moveable gas appliances, can/cga-6.16, and a quick-disconnect device that co...
P/n 24-156 rev a 7/00 page 10 important: do not obstruct the flow of combustion and ventilation air. Failure to vent ovens properly will result in operational problems, unsatisfactory baking results, and possible premature failure of burner components. Two methods acceptable for ventilation: • mecha...
P/n 24-156 rev a 7/00 page 11 insert picture minimum clearance from combustible materials.
P/n 24-156 rev a 7/00 page 12 failure to maintain minimum clearance in the back of the oven will result in operational problems and will shorten life of the blower. • maintain minimum clearance in the back of the oven. • do not obstruct ventilation. Insert pictures not acceptable acceptable minimum ...
P/n 24-156 rev a 7/00 page 13 after conversion-adjust air shutter on oven burner th maximum gas supply pressure to the regulator should never exceed 14” w.C. (water column) ½ (psi 3.5 kpa) diagram test for leakage: to check for leaks, use a commercial leak detecting solution or soap suds. Do not use...
P/n 24-156 rev a 7/00 page 14 insert diagram oven controls cook only 1. Power switch controls power to oven. 2. Blower switch controls blower operation. When in “manual” position, the blower is “on” at all times. When in “auto” position, the blower stops when the door is open. 3. Speed switch contro...
P/n 24-156 rev a 7/00 page 15 lighting instructions 1. Turn switch to “on” position. 2. Turn thermostat dial to temperature required. 3. When burner ignites, press blower switch to automatic. Do not operate oven without blower for more than 3 minutes. 4. If pilot is extinguished, turn thermostat to ...
P/n 24-156 rev a 7/00 page 16 oven operation 1. Turn power switch (1) to “on” position. 2. Set blower switch (2) to the “auto” position 3. Set speed switch (3) to the “low” position. 4. Set cook thermostat (5) to the desired baking or roasting temperature. 5. Preheat oven until indicator light (6) g...
P/n 24-156 rev a 7/00 page 17 diagram oven control cook and hold 1. Power switch controls power to oven. 2. Blower switch controls blower operation. When in “manual” position, the blower is “on” at all times. When in “auto” position, the blower stops when the door is opened. 3. Speed switch controls...
P/n 24-156 rev a 7/00 page 18 diagram to program press “start/stop” button until display alternates between “stop” and “sense” temperature. The control is now ready for programming. Preheat temp press “prog adv” button until “preheat temp” light turns on. Press ↑ or ↓ buttons to obtain desired temp....
P/n 24-156 rev a 7/00 page 19 regulates the pre-set points, but the cook count down timer will stop. Pressing the “prog adv” button until the desired indicator light turns on can change cooking parameters. The display will show preset value. Pressing the ↑ or ↓ will allow settings changed as desired...
P/n 24-156 rev a 7/00 page 20 • *doors synchronization: done by method describe above. • clearance, doors & gasket: 1. Loosen door hinge bolts 2. Make adjustment in front to back direction. 3. Tighten door hinge bolts securely. Picture removal and replacement warning before any repairs or service tu...
P/n 24-156 rev a 7/00 page 21.
P/n 24-156 rev a 7/00 page 22 for optimum performance, please observe the following procedures and suggestions: in the event of power failure: this appliance is not capable of being operated by manual lighting or otherwise. When in operation, this appliance is designed to safety shut itself down in ...
P/n 24-156 rev a 7/00 page 23 1. Turn off gas supply. 2. Remove the outlet pressure tap plug from the manifold and install manometer. 3. Remove seal screw from the regulator stack. For gas conversion, follow these steps: • remove adjustment screw. • remove and replace regulator spring (conversion ki...
P/n 24-156 rev a 7/00 page 24 turn off gas and electrical supply • remove racks and guides. • remove blower baffle by removing wingnuts and pulling baffle forward. • loosen setscrew in blower wheel hub. • use blower wheel puller to remove blower wheel from motor shaft. • to reinstall blower wheel. T...
P/n 24-156 rev a 7/00 page 25 • for racks, guides, and blower wheel, use solution of ammonia and water. Turn off gas and electrical supply motor removal and replacement is from front of oven. • remove blower baffle and blower wheel (see page 21). • remove six outer screws in motor mounting plate and...
P/n 24-156 rev a 7/00 page 26 control cover • after removing control cover, swing control box panel forward. • access to: switches thermostat ignition box electrical terminal gas shut off valve gas valve union diagram control box.
P/n 24-156 rev a 7/00 page 27 insert wiring diagram wiring diagram.
