JALpower D-NS SERIES User Manual - page 9
●
Menu display can be controlled by pressing the key,
and holding the key for a while will enter into the
submenu.
Line
②
:
●
This is area which display the present power
generation of the system.
13
14
Status
Display
E
-
Today
=
15
.
2KWh
E
-
Total
=
33
.
17MWh
Vac
=
229
.
5V
Iac
=
11
.
3A
XXXXXXN-DS
Ver
:
V1
.
00
Set
Language
Set
Time
First
Level
Menu
……
Fac
=
50
.
00Hz
20
0
0
-
00
-
00
00
:
00
Error
History
E01
110822
01
:
01
No
Error
Lock
Short
press
for
safety
country
select
Second
Level
Menu
Wi-Fi
Reset
Wi-Fi
Reload
Wi-Fi
Resetting
...
Wi-Fi
Reset
OK
Wi-Fi
Reset
Fail
Wi-Fi
Reloading
...
Wi-Fi
Reload
OK
Wi-Fi
Reload
Fail
Vpv
=
325
.
5V
Ipv
=
8
.
0A
Default
English
Deutsch
Angielski
Long
press
2S
Long
press
2S
Long
press
2S
Long
press
2S
Long
press
2S
Long
press
2S
Long
press
2S
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Short
press
Long
press
2S
Long
press
2S
Long
press
2S
Short
press
to
set
the
third
number
Short
press
to
set
the
fourth
number
Short
press
to
set
the
last
number
Long
press
2S
Wait
25S
Wait
25S
200
0
-
00
-
00
00
:
00
2000
-
00
-
00
00
:
0
0
Set Protocol
Long
press
2S
RS-485
Wi-Fi
Short press
Short press
PF Adjust
Long
press
2S
Disable
lagging 0.99
lagging 0.
9
9
lagging 0.9
9
Short Press chose
Leading or lagging
Short press
Short Press chose 8 or 9
Long
press
2S
Long
press
2S
Short Press chose 0 or 9
Shadow
OFF
MPPT
Power Limit ON
Set Power Limit
100%Prated
Set Power Limit
1
00%Prated
Short Press
chose 0 or 1
Set Power Limit
1
0
0%Prated
Short Press
chose 0 to 9
Set Power Limit
10
0
%Prated
Short Press
chose 0 to 9
Power Limit
OFF
Shadow MPPT
ON
70
%
Rated
Enable
Recover
Rated
Power
Long
press
2S
Or
Short
press
Short
press
Only available for German market
4.2 User interface and use of the display
(
1)
A schematic of the display screen is shown as below:
(
2) Display area
Line
①---
Working status information
●
This area displays the status information. “Waiting” indicates the inverter is standby for power generation;
“
Checking **S”
(checking time is
based on safety, and varies from country to country) indicates the inverter is self-checking, counting down and
preparing for power generation. “Normal” indicates the inverter is generating power. If any condition of the system is abnormal,
the screen will display an error message.
Refer to Table 4.3
.
●
Through key operation, the screen can display different information such as operation parameters and power generation status in
this area. There are two levels of menus, and the flow chart of first level menu is shown below:
Line
①
Line
②
Display area is divided as follows:
Indicator lights in Yellow/Green/Red correspondently refer to POWER/RUN/FAULT.
4 System Operation
4.1 Indicator Lights
Set Safety Country
:
If display shows 'Configure Safety', then long press (2S) the key to enter the second level menu. Short press to browse the safety
country available. Choose suitable safety country according to the location of installation. The inverter will store the chosen safety
country after 20 seconds of no operation.
P
a
c
=
2
0
0
0
.
0
W
N
o
r
m
a
l
POWER
RNU
FAULT
ON = WiFi CONNECTED / ACTIVE
BLINK 1 = WiFi SYSTEM RESETTING
BLINK 2 = WiFi ROUTER PROBLEM
BLINK 4 = WiFi SERVER PROBLEM
OFF = WiFi NOT ACTIVE
ON = INVERTER IS FEEDING POWER
OFF = INVERTER IS NOT FEEDING POWER AT THE MOMENT
BLINK = RS485 CONNECTED
ON = FAULT OCCURRED
OFF = NO FAULT