1. DL manuals
  2. Jeep
  3. Automobile
  4. 2015 Cherokee
  5. Owner's Manual

Jeep 2015 Cherokee Owner's Manual

Summary of 2015 Cherokee

  • Page 1

    Cherokee o w n e r ’ s m a n u a l 20 15 cher ok ee 15kl74-126-ad fourth edition rev 1 printed in u.S.A. 2 0 1 5 fca us llc.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engine...

  • Page 7

    Control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the unive...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against oper- ating procedures that could result in a collision or bodily injury. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss important...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ ignition node module (ignm) — if equipped. .12 ▫ keyless ignition node (kin) . . . . . . . . . . . . . .13 ▫ key fob — if equipped . . . . . . . . . . . . . . . . . .14 ▫ ignition or accessory...

  • Page 12

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . .25 ▫ programming additional transmitters . . . . . . .25 ▫ transmitter battery replacement . . . . . . . . . . .25 ▫ general information . . . . . . . . . . . . . . . . . . . .29 䡵 remote starting system — if equipped . . . . . . . . . . . ....

  • Page 13

    ▫ power liftgate — if equipped . . . . . . . . . . . . .48 䡵 occupant restraint systems . . . . . . . . . .50 ▫ important safety precautions . . . . . . . . . . . . . .51 ▫ seat belt systems . . . . . . . . . . . . . . . . . . . . . .52 ▫ supplemental restraint system (srs) . . . . . . . .64 ▫ child...

  • Page 14

    A word about your keys your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a either a key fob with remote keyless entry (rke) transmitter and an ignition node module (ignm). The keyless ignition system consists of a key fob with ...

  • Page 15

    Keyless ignition node (kin) this feature allows the driver to operate the ignition with the push of a button as long as the remote keyless entry (rke) transmitter is in the passenger compartment. The keyless ignition node (kin system) has four oper- ating positions, three of which are labeled and wi...

  • Page 16

    Key fob — if equipped the key fob also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the key fob go dead. You can keep the emergency key with ...

  • Page 17

    Note: you can insert the double-sided emergency key into the lock cylinders with either side up. Ignition or accessory on message when opening the driver’s door when the ignition is in acc or on/run (engine not running), a chime will sound to remind you to place the ignition in the off position. In ...

  • Page 18

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the key fob in or near th...

  • Page 19

    Operation. Therefore, only key fobs that are pro- grammed to the vehicle can be used to start and operate the vehicle. The system will not allow the engine to crank with an invalid key fob. After placing the ignition to the on/run position, the vehicle security light will turn on for three seconds f...

  • Page 20

    Caution! • always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unat- tended. • for vehicles equipped with keyless enter-n-go™, always remember to place the ignition in the off position. Note: duplication of key fobs may be performed at an authorized dealer. This p...

  • Page 21

    Vehicle security alarm — if equipped the vehicle security alarm monitors the vehicle doors for unauthorized entry and the keyless enter-n-go™ start/stop button for unauthorized operation. While the vehicle security alarm is armed, interior switches for door locks and liftgate release are disabled. I...

  • Page 22

    • for vehicles not equipped with keyless enter-n- go™, make sure the vehicle ignition system is off, and the key is physically removed from the ignition. 2. Perform one of the following methods to lock the vehicle: • push lock on the interior power door lock switch with the driver and/or passenger d...

  • Page 23

    • for vehicles not equipped with keyless enter-n- go™, insert a valid key into the ignition switch and turn the key to the on position. Note: • the driver’s door key cylinder and the liftgate button on the rke transmitter cannot arm or disarm the vehicle security alarm. • the vehicle security alarm ...

  • Page 24

    Security system manual override the vehicle security alarm will not arm if you lock the doors using the manual door lock plunger. Illuminated entry the courtesy lights will turn on when you use the remote keyless entry (rke) transmitter to unlock the doors or open any door. This feature also turns o...

  • Page 25

    Remote keyless entry (rke) to unlock the doors and liftgate push and release the unlock button on the rke transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated en...

  • Page 26

    If the vehicle is equipped with passive entry, refer to “keyless enter-n-go™” in “things to know before starting your vehicle” for further information. 1st push of key fob unlocks this feature lets you program the system to unlock either the driver’s door or all doors on the first push of the unlock...

  • Page 27

    Sound horn with lock this feature will cause the horn to chirp when the doors are locked with the rke transmitter. This feature can be turned on or turned off. To change the current setting, refer to “uconnect® settings” in “understanding your instrument panel” for further information. Using the pan...

  • Page 28

    Note: • perchlorate material — special handling may apply. See www.Dtsc.Ca.Gov/hazardouswaste/perchlorate • do not touch the battery terminals that are on the back housing or the printed circuit board. 1. Remove the emergency key by sliding the mechanical latch on the back of the rke transmitter sid...

  • Page 29

    2. Separating rke halves requires screw removal (if equipped) and gently prying the two halves of the rke transmitter apart with the emergency key. Make sure not to damage the seal during removal. Emergency key removal (kin) remove screw from transmitter case 2 things to know before starting your ve...

  • Page 30

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, and then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of separating ignition node modul...

  • Page 31

    The battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4. To assemble the rke transmitter case, snap the two halves together. General information this device comp...

  • Page 32

    Note: • the vehicle must be equipped with an automatic transmission to be equipped with remote start. • obstructions between the vehicle and rke transmitter may reduce this range. How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever i...

  • Page 33

    Warning! (continued) • keep remote keyless entry (rke) transmitters away from children. Operation of the remote start system, windows, door locks or other controls could cause serious injury or death. Remote start abort message on electronic vehicle information center (evic) or driver information di...

  • Page 34

    Note: • if an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds. • the park lamps will turn on and remain on during remote start mode. • for security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the ...

  • Page 35

    Note: • for vehicles not equipped with the keyless enter-n- go™ feature, the ignition switch must be in the on/run position in order to drive the vehicle. • for vehicles not equipped with the keyless enter-n- go™ feature, the message “remote start active — insert key and turn to run” will display in...

  • Page 36

    Resume previous operation, except if the windshield wiper de-icer is active. The windshield wiper de-icer timer and operation will continue. Door locks manual door locks to lock each door, rotate the door lock knob on each door trim panel forward. To unlock the front doors, pull the inside door hand...

  • Page 37

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n-go™ in the acc or on/run mode. A child could operate power windows, other controls, or move the vehicle. Power doo...

  • Page 38

    Is open, the power locks will not operate. This prevents you from accidentally locking the key fob in the vehicle. Placing the ignition to the off position or closing the door will allow the locks to operate. If a door is open, and the ignition is in the acc or on/run position, a chime will sound as...

  • Page 39

    To use the system, open each rear door, use a flat blade screwdriver (or ignition key) and rotate the dial to the lock or unlock position. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position. Not...

  • Page 40

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Keyless enter-n-go™ the passive entry system is an enhancement to the vehicle’s remote keyless entry (rke) system and a feature of...

  • Page 41

    Note: if “unlock all doors 1st push” is programmed all doors will unlock when you grab hold of the front driver’s door handle. To select between “unlock driver door 1st push” and “unlock all doors 1st push,” refer to “uconnect® settings” in “understanding your instru- ment panel” for further informa...

  • Page 42

    Fobik-safe only executes in vehicles with passive entry. There are three situations that trigger a fobik-safe search in any passive entry vehicle: • a lock request is made by a valid passive entry rke transmitter while a door is ajar. • a lock request is made by the passive entry door handle while a...

  • Page 43

    Note: if “unlock all doors 1st push” is programmed in evic/did (if equipped), all doors will unlock when you push the electronic release on the liftgate. If ⬙ unlock driver door 1st push ⬙ is programmed in uconnect®, the liftgate will unlock when you push the electronic release on the liftgate. For ...

  • Page 44

    Do not grab the door handle, when pushing the door handle lock button. This could unlock the door(s). Push the door handle button to lock do not grab the door handle when locking 42 things to know before starting your vehicle.

  • Page 45

    Note: • after pushing the door handle button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle without the vehicle reacting and unlocking. • if passive ent...

  • Page 46

    Warning! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n- go™ in the acc or on/run mode. O...

  • Page 47

    To close the window part way, lift the window switch to the first detent and release it when you want the window to stop. Note: • if the window runs into any obstacle during auto- closure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close t...

  • Page 48

    The down position). To enable the window controls, push and release the window lockout button again (setting it in the up position). Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffetin...

  • Page 49

    To lock the liftgate with a valid passive entry rke transmitter within 3 ft (1.0 m) of the liftgate, push the passive entry lock button located to the right of electronic liftgate release. Note: the liftgate passive entry lock button will only lock the liftgate. The liftgate unlock feature is built ...

  • Page 50

    Warning! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Power liftgate — if equipped the power liftgate may be opened by pushing the electronic...

  • Page 51

    Note: • in the event of a power malfunction to the liftgate, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the lift- gate trim panel. • if liftgate is left open for an extended period of t...

  • Page 52

    Open, push the liftgate button on the key fob to fully open the liftgate and then push it again to close. • if the electronic liftgate release is pushed while the power liftgate is closing, the liftgate will reverse to the full open position. • if the electronic liftgate release is pushed while the ...

  • Page 53

    Important safety precautions please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible. Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1. C...

  • Page 54

    Side air bags will inflate forcefully into the space between you and the door and you could be injured. 9. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer center. Phone numbers are provided under ⬙ if you need consumer assistance. ⬙ w...

  • Page 55

    The start or on/run position. If the driver or outboard front seat passenger is unbelted, the seat belt reminder light will turn on and remain on until both outboard front seat belts are buckled. The beltalert warning sequence begins after the vehicle speed is over 5 mph (8 km/h) by blinking the sea...

  • Page 56

    The seat belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoul- der part of the seat belt to move freely with you under normal conditions. However, in a collision the seat belt will lock and reduce your risk of striking the inside of the vehicle ...

  • Page 57

    Warning! (continued) • wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of the seat belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • two people ...

  • Page 58

    Warning! (continued) • a seat belt that is worn under your arm is danger- ous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A seat belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the seat...

  • Page 59

    2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the seat belt. Slide the latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. 3...

  • Page 60

    Plate and pull on the lap belt. A snug seat belt reduces the risk of sliding under the seat belt in a collision. 5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in t...

  • Page 61

    4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted. Adjustable upper shoulder belt anchorage in the driver and front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from you...

  • Page 62

    Note: the adjustable upper shoulder belt anchorage is equipped with an easy up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- ton. To verify the shoulder belt anchorage is latched, pull downward on the shou...

  • Page 63

    Pregnant women should wear the lap part of the seat belt across the thighs and as snug across the hips as possible. Keep the seat belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat belt pretensioner the front ...

  • Page 64

    If the passenger seating position is equipped with an alr and is being used for normal usage: only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt r...

  • Page 65

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 66

    Warning! (continued) only used to install rear-facing or forward-facing child restraints that have a harness for restraining the child. Supplemental restraint system (srs) air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint contro...

  • Page 67

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 68

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 69

    Warning! (continued) • do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air ba...

  • Page 70

    When the orc detects a collision requiring the ad- vanced front air bags, it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the advanced front air bags. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of ...

  • Page 71

    Order for the ocs to operate as designed, it is important for the front passenger to be seated properly and prop- erly wearing the seat belt. The ocs will not prevent deployment of the passenger advanced front air bag. The ocs may reduce the inflation rate of the passenger advanced front air bag if ...

  • Page 72

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 73

    Lighter weight passengers (including small adults) when a lighter weight passenger, including a small adult, occupies the front passenger seat, the ocs may reduce the inflation rate of the passenger advanced front air bag. This does not mean that the ocs is working improperly. Do not decrease or inc...

  • Page 74

    Examples of improper front passenger seating include: • the front passenger’s weight is transferred to another part of the vehicle (like the door, arm rest or instru- ment panel). • the front passenger leans forward, sideways, or turns to face the rear of the vehicle. • the front passenger’s seatbac...

  • Page 75

    Not seated properly not seated properly 2 things to know before starting your vehicle 73.

  • Page 76

    Not seated properly not seated properly 74 things to know before starting your vehicle.

  • Page 77

    Warning! • if an occupant in the front passenger seat is seated improperly, the occupant may provide an output signal to the ocs that is different from the occu- pant’s properly seated weight input. This may result in serious injury or death in a collision. • always wear your seat belt and sit prope...

  • Page 78

    Classify the seated weight of a front seat passenger, the ocs components must function as designed. Do not make any modifications to the front passenger seat components, assembly, or to the seat cover. If the seat, trim cover, or cushion needs service for any reason, take the vehicle to your authori...

  • Page 79

    Knee impact bolsters the knee impact bolsters help protect the knees of the driver and front passenger, and position the front occu- pants for improved interaction with the advanced front air bags. Warning! • do not drill, cut, or tamper with the knee impact bolsters in any way. • do not mount any a...

  • Page 80

    Supplemental side air bags your vehicle is equipped with two types of side air bags: 1. Supplemental seat-mounted side air bags (sabs): located in the outboard side of the front and rear (in vehicles equipped with rear seat sabs) seats. The sabs are marked with a “srs airbag” or “airbag” label sewn ...

  • Page 81

    The sabs may help to reduce the risk of occupant injury during certain side impact and certain rollover events, in addition to the injury reduction potential provided by the seat belts and body structure. When the sab deploys, it opens the seam on the out- board side of the seatback’s trim cover. Th...

  • Page 82

    Sabics may help reduce the risk of head injury to front and rear seat outboard occupants. Sabics may reduce the risk of injuries in certain side impact and vehicle rollover events, in addition to the injury reduction poten- tial provided by the seat belts and body structure. The sabics deploy downwa...

  • Page 83

    Warning! • your vehicle is equipped with left and right supplemental side air bag inflatable curtains (sabics). Do not stack luggage or other cargo up high enough to block the deployment of the sabics. The trim covering above the side win- dows where the sabic and its deployment path are located sho...

  • Page 84

    Help keep you in position, away from inflating side air bags. To get the best protection from the side air bags, occupants must wear their seat belts properly and sit upright with their backs against the seats. Children must be properly restrained in a child restraint or booster seat that is appropr...

  • Page 85

    The side air bags will not deploy in all side collisions, including some collisions at certain angles, or some side collisions that do not impact the area of the passenger compartment. The side air bags may deploy during angled or offset frontal collisions where the advanced front air bags deploy. R...

  • Page 86

    Deploy and unfold. The abrasions are similar to fric- tion rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or ...

  • Page 87

    Enhanced accident response system in the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the orc will determine whether to have the enhanced accident response sys- tem perform the following functions: • cut off fuel...

  • Page 88

    The orc contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. The orc turns on the air bag warning light in the instrument panel for approximately four to eight seconds for a self-check when the ignition is ...

  • Page 89

    Warning! Ignoring the air bag warning light in your instru- ment panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first placed in the on position, and stays on after you start the vehicle, or if it comes on...

  • Page 90

    Warning! (continued) stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or add aftermarket side steps or running boards. • it is dangerous to try to repair any part of the air bag system yourself. Be ...

  • Page 91

    • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if at all) the driver was pushing the accelera- tor and/or brake pedal; and, • how fast the vehicle was traveling. These data can help provide a better understanding of the circumstances in which crashes and inj...

  • Page 92

    Warning! In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in you...

  • Page 93

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 94

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 95

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 96

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 97

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 98

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 99

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 2 things to know before starting your vehicle 97.

  • Page 100

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage sys- tem to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and te...

  • Page 101

    Can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more in- formation. Can the head restraints be remove...

  • Page 102

    Locating tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower ancho...

  • Page 103

    Tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center seat latch this vehicle has 5 lower latch anchorages in the rear seat. Anchorages a and b are used for the right outboard posi...

  • Page 104

    Seating positions using lower anchorages a and b, and d and e. Do not use the center seat anchorage, c. If the child seats do not block the center seat belt webbing and buckle, the center seat belt can be used to restraint an occupant or child restraint in the center seating position. 2. Right outbo...

  • Page 105

    Warning! (continued) the latch anchors or the vehicle’s seat belt for installing the child seat in position (1), behind the front passenger. Please refer to “installing the latch-compatible child restraint system” for typical installation instructions. Always follow the directions of the child restr...

  • Page 106

    4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tions to attach a tether anchor. 5. Tighten all of the straps as you push the child restraint rearward and downward into the s...

  • Page 107

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 108

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor • top tether anchorage symbol 106 things to know before starting your vehicle.

  • Page 109

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for- ward facing child restrai...

  • Page 110

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 111

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the seat belt path. It should not move more than 1 inch (25.4 mm) in any ...

  • Page 112

    1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another p...

  • Page 113

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 114

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tip...

  • Page 115

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 116

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 117

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 118

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 119: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 ▫ inside day/night mirror — if equipped . . . .124 ▫ assist and 9–1–1 rearview mirror — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .124 ▫ outside mirrors . . ...

  • Page 120

    ▫ manual seats — if equipped . . . . . . . . . . . . .144 ▫ front heated seats — if equipped . . . . . . . . .147 ▫ front ventilated seats — if equipped . . . . . . .148 ▫ head restraints . . . . . . . . . . . . . . . . . . . . . .149 ▫ 60/40 split folding rear seat with fold-flat feature . . . . . ...

  • Page 121

    ▫ high/low beam switch . . . . . . . . . . . . . . . .166 ▫ flash-to-pass . . . . . . . . . . . . . . . . . . . . . . . .166 ▫ front map/reading lights . . . . . . . . . . . . . . .166 ▫ interior lights . . . . . . . . . . . . . . . . . . . . . . .167 ▫ battery saver feature . . . . . . . . . . . . ...

  • Page 122

    ▫ to activate/deactivate. . . . . . . . . . . . . . . . . .185 ▫ to set a desired acc speed . . . . . . . . . . . . .187 ▫ to cancel . . . . . . . . . . . . . . . . . . . . . . . . . . .187 ▫ to turn off . . . . . . . . . . . . . . . . . . . . . . . . . .188 ▫ to resume . . . . . . . . . . . . . . ....

  • Page 123

    ▫ changing lanesense status . . . . . . . . . . . . . .224 䡵 parksense® rear park assist — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .224 ▫ parksense® sensors . . . . . . . . . . . . . . . . . . . .225 ▫ parksense® warning display . . . . . . . . . . . . .225 ▫ parksense® displ...

  • Page 124

    䡵 parkview® rear back up camera — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .275 䡵 garage door opener — if equipped . . .278 ▫ before you begin programming homelink® . .279 ▫ programming a rolling code . . . . . . . . . . . . .279 ▫ programming a non-rolling code . . . . . . . ...

  • Page 125

    䡵 power inverter — if equipped . . . . . . . .296 䡵 wireless charging pad — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .297 ▫ wireless charging pad operation . . . . . . . . . .298 䡵 cupholders . . . . . . . . . . . . . . . . . . . . . . . .301 䡵 storage . . . . . . . . . . . . ...

  • Page 126

    Mirrors inside day/night mirror — if equipped a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror hea...

  • Page 127

    Left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. If equipped, the rearview mirror contains an assist and a 9-1-1 button. Note: the assist and 9–1–1 features operate through the uconnect® access service. These buttons will only operate ...

  • Page 128

    • vehicle customer care – total support for all other vehicle issues. 9-1-1 call 1. Push the 9-1-1 call button on the rearview mirror. Note: in case the 9-1-1 call button is pushed in error, there will be a 10 second delay before the 9-1-1 call system initiates a call to a 9-1-1 operator. To cancel ...

  • Page 129

    Note: once a connection is made between the vehicle’s 9-1-1 call system and the 9-1-1 operator, the 9-1-1 opera- tor may be able to open a voice connection with the vehicle to determine if additional help is needed. Once the 9-1-1 operator opens a voice connection with the vehicle’s 9-1-1 call syste...

  • Page 130

    Warning! (continued) during or after an accident), the uconnect® features, apps and ser- vices, among others, will not operate. • modifications to any part of the 9-1-1 call system could cause the air bag system to fail when you need it. You could be injured if the air bag system is not there to hel...

  • Page 131

    Warning! (continued) • the occupant restraint control module turns on the air bag warning light on the instrument panel if a malfunction in any part of the system is detected. If the air bag warning light is illumi- nated, have an authorized dealer service the orc system immediately. Even if the 9-1...

  • Page 132

    Note: never place anything on or near the vehicle’s wireless and gps antennas. You could prevent wireless and gps signal reception, which can prevent your vehicle from placing an emergency call. Wireless and gps signal reception is required for the 9-1-1 call system to function properly. General inf...

  • Page 133

    Power mirrors the power mirror switches are located on the driver’s door trim panel. Models with expush window feature push and release the mirror select button marked l (left) or r (right) and then push one of the four arrow buttons to move the mirror in the direction the arrow is pointing. The sel...

  • Page 134

    Power folding mirrors — if equipped the switch for the power folding mirrors is located between the power mirror switches l (left) and r (right). Push the switch once and the mirrors will fold in, pushing the switch a second time will return the mirrors to the normal driving position. Note: if the v...

  • Page 135

    To reset the power folding mirrors: fold and unfold them by pushing the button. (this may require multiple button pushes). This resets them to their normal position. Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rea...

  • Page 136

    1. Fold down the sun visor. 2. Unclip the visor from the center clip. 3. Pull the sun visor toward the inside rearview mirror to extend it. Blind spot monitoring (bsm) — if equipped the blind spot monitoring (bsm) system uses two radar- based sensors, located inside the rear bumper fascia, to detect...

  • Page 137

    The bsm detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m). The zone length starts at the outside mirror and extends approxi- mately 10 ft (3 m) beyond the rear bumper of the vehicle. The bsm system monitors the detection zones on both sides of the vehicle ...

  • Page 138

    The bsm system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary. The bsm system will issue an alert during these types of zone entries. Entering from the side vehicles that move into your adjacent lanes from either side o...

  • Page 139

    Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Overtaking traffic if you pass another vehicle slowly with a relative speed less than 10 mph (16 km/h) and the vehicle remains i...

  • Page 140

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The bsm system will not alert you of objects t...

  • Page 141

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm (continued) warning! (continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicles m...

  • Page 142

    Rcp monitors the rear detection zones on both sides of the vehicle, for objects that are moving toward the side of the vehicle with a minimum speed of approximately 3 mph (5 km/h), to objects moving a maximum of approximately 20 mph (32 km/h), such as in parking lot situations. Note: in a parking lo...

  • Page 143

    Modes of operation three selectable modes of operation are available in the uconnect® system. Refer to “uconnect® settings/ customer programmable features” in “understanding your instrument panel” for further information. Blind spot alert lights only when operating in blind spot alert mode, the bsm ...

  • Page 144

    Note: the bsm system will store the current operating mode when the vehicle is shut off. Each time the vehicle is started the previously stored mode will be recalled and used. General information this vehicle has systems that operate on radio frequency that comply with part 15 of the federal communi...

  • Page 145

    Power seats — if equipped some models may be equipped with a power driver’s seat. The power seat switch is located on the outboard side of the seat near the floor. Use the switch to move the seat up, down, forward or rearward. Reclining the seatback forward or rearward the seatback can be reclined b...

  • Page 146

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Power lumbar — if equipped vehicles equipped with power driver or passenger seats may ...

  • Page 147

    While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! • adjusting a seat while driving...

  • Page 148

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Manual seat height adjustment — if equipped the driver’s seat height can be raised or ...

  • Page 149

    Front heated seats — if equipped the front heated seats control buttons are located within the uconnect® system. You can gain access to the control buttons through the climate screen or the controls screen. • press the heated seat button once to turn the hi setting on. • press the heated seat button...

  • Page 150

    Warning! (continued) even at low temperatures, especially if used for long periods of time. • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause se...

  • Page 151

    This feature can be programmed through the uconnect® system. Refer to “uconnect® settings” in “understand- ing your instrument panel” for further information. Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head re...

  • Page 152

    Note: the head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. Warning! Do not place items over the top of the reactive head restraint, such as coats, seat covers or portable dvd pl...

  • Page 153

    60/40 split folding rear seat with fold-flat feature to provide additional storage area, each rear seat can be folded flat. This allows for extended cargo space and still maintains some rear seating room. Note: prior to folding the rear seat, it may be necessary to position the front seat to its mid...

  • Page 154

    Rear seat forward/rearward adjustment lift up on the adjusting bar located at the front of the seat near the floor and release it when the seat is at the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. To lower the r...

  • Page 155

    To raise the rear seat note: if interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Raise the seatback and lock it into place. Warning! Be certain that the seatback is securely locked into position. If the sea...

  • Page 156

    Driver memory seat — if equipped this feature allows the driver to store up to two different memory profiles, for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat and side mirrors and a set of desired radio station presets. The memory sw...

  • Page 157

    2. Adjust all memory profile settings to desired prefer- ences (i.E., seat, side mirror and radio station presets). 3. Push and release the set button on the memory switch, then push the number (1) button within five seconds. The electronic vehicle information center (evic) or driver information dis...

  • Page 158

    Note: before programming your rke transmitters you must select the “memory to fob” feature through the uconnect® system screen. Refer to “uconnect® settings” in “understanding your instrument panel” for further information. To program your rke transmitters, perform the following: 1. Cycle the vehicl...

  • Page 159

    To recall the memory settings for driver one, push memory button number 1 or the unlock button on the rke transmitter linked to memory position 1. To recall the memory setting for driver two, push memory button number 2 or the unlock button on the rke transmitter linked to memory position 2. A recal...

  • Page 160

    Note: the easy entry/exit feature is not enabled when the vehicle is delivered from the factory. The easy entry/exit feature is enabled (or later disabled) through the programmable features in the uconnect® system. Refer to “uconnect® settings/customer programmable features” in “understanding your i...

  • Page 161

    2. Move to the outside of the vehicle and pull the safety latch release lever forward (toward you). The safety latch release lever is located behind the center front edge of the hood. Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mate...

  • Page 162

    Lights headlight switch the headlight switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, auto- matic headlights — if equipped, instrument panel lights, instrument panel light dimming, interior lights and fog lights — if e...

  • Page 163

    Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation. When the system is on, the headlight time delay feature is...

  • Page 164

    If you turn the headlights or parking lights on, or place the ignition in acc or run, the system will cancel the delay. If you turn the headlights off before the ignition, they will turn off in the normal manner. Note: • the lights must be turned off within 45 seconds of placing the ignition in the ...

  • Page 165

    • broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly. • to opt out of the adv...

  • Page 166

    Daytime running lights (drl) — if equipped the daytime running lights will turn on when the engine is started and remain on unless the headlamps are turned on, the parking brake is applied, or the engine is shut off. Note: if allowed by law in the country in which the vehicle was purchased the dayti...

  • Page 167

    An indicator light in the instrument cluster illuminates when the fog lights are turned on. Note: the fog lights will operate with the low beam headlights or parking lights on. However, selecting the high beam headlights will turn off the fog lights. Multifunction lever the multifunction lever contr...

  • Page 168

    Note: • if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. • a “turn signal on” message will appear in the evic/ di...

  • Page 169

    Switch on either side of the console. To turn the lights off, push the switch a second time. These lights also turn on when a door is opened, or when the unlock button on the remote keyless entry (rke) transmitter is pushed, or when the dimmer control is turned completely upward to the second detent...

  • Page 170

    With the parking lights or headlights on, rotating the instrument panel dimmer control upward will increase the brightness of the instrument panel lights and lighted cupholders — if equipped. Ambient light control — if equipped rotate the ambient dimmer control upward or down- ward to increase or de...

  • Page 171

    Dome light position rotate the instrument panel dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the instrument panel dimmer control is in this position. Interior light defeat (off) rotate the instrument panel dimmer contro...

  • Page 172

    Windshield wiper operation rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation. Windshield wiper/washer lever windshield wiper operation 170 understanding the features ...

  • Page 173

    Caution! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur. Intermittent wiper system use one of the...

  • Page 174

    While in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the lever is released, and then resume the intermittent interval pre- viously selected. If the lever is pulled while the wipers are in the off position, the wipers will operate for several wipe cycle...

  • Page 175

    Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Windshield wiper de-icer — if equipped your vehicle may be equipped with a windshield wiper de-ic...

  • Page 176

    Rain sensing wipers — if equipped this feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of ...

  • Page 177

    • transmission in neutral position — when the ignition is on, and the automatic transmission is in the neutral position, the rain sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 5 mph (8 km/h), or the shift lever/gear selector is moved out of the neutra...

  • Page 178

    To unlock the steering column, push the control handle downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as de- sired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering col...

  • Page 179

    • push the heated steering wheel button once to turn the heating element on. • push the heated steering wheel button a second time to turn the heating element off. Note: the engine must be running for the heated steering wheel to operate. Vehicles equipped with remote start on models that are equipp...

  • Page 180

    The electronic speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic ...

  • Page 181

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 182

    The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “under- standing your instrument panel” for more information. The speed increment shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pushing the set + b...

  • Page 183

    • if the button is continually pushed, the set speed will continue to decrease until the button is released, then the new set speed will be established. Metric speed (km/h) • pushing the set - button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a d...

  • Page 184

    Adaptive cruise control (acc) — if equipped adaptive cruise control (acc) increases the driving convenience provided by cruise control while traveling on highways and major roadways. However, it is not a safety system and not designed to prevent collisions. Electronic speed control function performs...

  • Page 185

    You can change the mode by using the cruise control buttons. The two control modes function differently. Always confirm which mode is selected. Warning! • adaptive cruise control (acc) is a convenience system. It is not a substitute for active driving involvement. It is always the driver’s responsib...

  • Page 186

    Warning! (continued) you should switch off the acc system: • when driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.E., in highway construction zones). • when entering a turn lane or highway off ramp; when driving on roads that are winding, icy, snow- co...

  • Page 187

    Note: any chassis/suspension or tire size modifications to the vehicle will effect the performance of the adaptive cruise control and forward collision warning system. Activating adaptive cruise control (acc) you can only engage acc if the vehicle speed is above 0 mph (0 km/h). The minimum set speed...

  • Page 188

    To turn the system off, push and release the adaptive cruise control (acc) on/off button again. At this time, the system will turn off and the evic/did will display “adaptive cruise control (acc) off.” warning! Leaving the adaptive cruise control (acc) system on when not in use is dangerous. You cou...

  • Page 189

    Warning! (continued) you could lose control and have a collision. Always leave the system off when you are not using it. To set a desired acc speed when the vehicle reaches the speed desired, push the set + button or the set - button and release. The evic/did will display the set speed. If the syste...

  • Page 190

    • the shift lever/gear selector is removed from the drive position. • the electronic stability control/traction control sys- tem (esc/tcs) activates. • the vehicle parking brake is applied. • driver seatbelt is unbuckled at low speeds. • driver door is opened at low speeds. • a trailer sway control ...

  • Page 191

    Warning! The resume function should only be used if traffic and road conditions permit. Resuming a set speed that is too high or too low for prevailing traffic and road conditions could cause the vehicle to accelerate or decelerate too sharply for safe operation. Failure to follow these warnings can...

  • Page 192

    Metric speed (km/h) • pushing the set + button once will result in a 1 km/h increase in set speed. Each subsequent tap of the button results in an increase of 1 km/h. • if the button is continually pushed, the set speed will continue to increase in 10 km/h increments until the button is released. Th...

  • Page 193

    Metric speed (km/h) • pushing the set - button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a decrease of 1 km/h. • if the button is continually pushed, the set speed will continue to decrease in 10 km/h decrements until the button is released. The...

  • Page 194

    Using this distance setting and the vehicle speed, acc calculates and sets the distance to the vehicle ahead. This distance setting displays in the evic/did. Distance setting 4 bars (longest) distance setting 3 bars (long) 192 understanding the features of your vehicle.

  • Page 195

    To increase the distance setting, push the distance setting — increase button and release. Each time the button is pushed, the distance setting increases by one bar (longer). Distance setting 2 bars (medium) distance setting 1 bar (short) 3 understanding the features of your vehicle 193.

  • Page 196

    To decrease the distance setting, push the distance set- ting — decrease button and release. Each time the button is pushed, the distance setting decreases by one bar (shorter). If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle is detected in the same ...

  • Page 197

    Note: the “brake!” screen in the evic/did is a warn- ing for the driver to take action and does not necessarily mean that the forward collision warning system is applying the brakes autonomously. Overtake aid when driving with acc engaged and following a target vehicle, the system will provide an ad...

  • Page 198

    If the target vehicle does not start moving within two seconds of your vehicle coming to a standstill, the driver will either have to push the res (resume) button, or apply the accelerator pedal to reengage the acc to the existing set speed. Note: after the acc system holds your vehicle at a standst...

  • Page 199

    Push the adaptive cruise control (acc) on/ off button (located on the steering wheel) until one of the following displays in the evic/did: adaptive cruise control off when acc is deactivated, the display will read “adap- tive cruise control off.” adaptive cruise control ready when acc is activated b...

  • Page 200

    This most often occurs at times of poor visibility, such as in snow or heavy rain. The acc system may also become temporarily blinded due to obstructions, such as mud, dirt or ice. In these cases, the evic/did will display “acc/fcw unavailable wipe front radar sensor” and the system will deactivate....

  • Page 201

    • do not attach or install any accessories near the sensor, including transparent material or aftermarket grilles. Doing so could cause an acc system failure or malfunction. When the condition that deactivated the system is no longer present, the system will return to the “adaptive cruise control of...

  • Page 202

    The “acc/fcw limited functionality clean front windshield” message can sometimes be displayed while driving in adverse weather conditions. The acc/fcw system will recover after the vehicle has left these areas. Under rare conditions, when the camera is not tracking any vehicles or objects in its pat...

  • Page 203

    Precautions while driving with acc in certain driving situations, acc may have detection issues. In these cases, acc may brake late or unexpect- edly. The driver needs to stay alert and may need to intervene. Towing a trailer towing a trailer is not advised when using acc. Offset driving acc may not...

  • Page 204

    The vehicle is out of the curve the system will resume your original set speed. This is a part of normal acc system functionality. Note: on tight turns acc performance may be limited. Using acc on hills when driving on hills, acc may not detect a vehicle in your lane. Depending on the speed, vehicle...

  • Page 205

    Lane changing acc may not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, acc has not yet detected the vehicle changing lanes and it may not detect the vehicle until it’s too late for the acc system to take action. Acc may not detect a vehic...

  • Page 206

    Stationary objects and vehicles acc does not react to stationary objects and stationary vehicles. For example, acc will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if nece...

  • Page 207

    Operation is subject to the following two conditions: 1. The device may not cause harmful interference. 2. The device must accept any interference received, including interference that may cause undesired op- eration of the device. Changes or modifications to any of these systems by other than an au...

  • Page 208

    To set a desired speed turn the normal (fixed speed) electronic speed control on. When the vehicle has reached the desired speed, push the set (+) or set (-) button and release. Release the accel- erator and the vehicle will operate at the selected speed. Once a speed has been set a message (cruise ...

  • Page 209

    • if the button is continually pushed, the set speed will continue to increase in 10 km/h increments until the button is released. The increase in set speed is reflected in the evic/did display. To decrease speed when the normal (fixed speed) cruise control is set, you can decrease speed by pushing ...

  • Page 210

    To cancel the following conditions will cancel the normal (fixed speed) electronic speed control without clearing the memory: • the brake pedal is applied. • the cancel button is pushed. • the electronic stability control/traction control sys- tem (esc/tcs) activates. • the vehicle parking brake is ...

  • Page 211

    Forward collision warning (fcw) with mitigation — if equipped forward collision warning (fcw) with mitigation operation the forward collision warning (fcw) system with mitigation provides the driver with audible warnings, visual warnings (within the evic/did), and may apply a brake jerk to warn the ...

  • Page 212

    When the system determines a collision with the vehicle in front of you is no longer probable, the warning message will be deactivated. Note: • the minimum speed for fcw activation is 1 mph (2 km/h). • the fcw alerts may be triggered on objects other than vehicles such as guard rails or sign posts b...

  • Page 213

    Warning! Forward collision warning (fcw) is not intended to avoid a collision on its own, nor can fcw detect every type of potential collision. The driver has the responsibility to avoid a collision by controlling the vehicle via braking and steering. Failure to follow this warning could lead to ser...

  • Page 214

    • changing the fcw status to “off” prevents the system from warning you of a possible collision with the vehicle in front of you. • changing the fcw sensitivity - near vs. Far. Far warns the driver of a possible collision earlier and near warns the driver later. • changing the active braking status ...

  • Page 215

    Note: • the system will retain the last setting selected by the driver after ignition shut down. • fcw may not react to irrelevant objects such as overhead objects, ground reflections, objects not in the path of the car, stationary objects that are far away, oncoming traffic, or leading vehicles wit...

  • Page 216

    Lanesense system uses a forward looking camera to detect lane markings and measure vehicle position within the lane boundaries. When both lane markings are detected and the driver unintentionally drifts out of the lane (no turn signal applied), the lanesense system provides a haptic warn- ing in the...

  • Page 217

    To turn the lanesense system on, push the lanesense button to turn the system on (led turns off). A “lane sense on” message is shown in the evic/did. To turn the lanesense system off, push the lanesense button once to turn the system off (led turns on). Note: the lanesense system will retain the las...

  • Page 218

    Lanesense warning message the lanesense system will indicate the current lane drift condition through the electronic vehicle information center (evic) or driver information display (did). 3.5 evic screen — if equipped when the lanesense system is on; the lane lines are gray when both of the lane bou...

  • Page 219

    • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes from white to gray, the left thin line remains solid white and the lanesense indi- cator changes from solid white to flashing yellow. Note: the lanesense system oper...

  • Page 220

    • when the lanesense system senses a lane drift situa- tion, the left thick lane line and the left thin line turn solid white. The lanesense indicator changes from solid green to solid yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. • for ...

  • Page 221

    • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes from white to gray, the left thin line remains solid white and the lanesense indi- cator changes from solid yellow to flashing yellow. At this time torque is applied...

  • Page 222

    7.0 did screen — if equipped when the lanesense system is on; the lane lines are gray when both of the lane boundaries have not been detected and the lanesense indicator is solid white. Left lane departure — only left lane detected • when the lanesense system is on, the lanesense indicator is solid ...

  • Page 223

    Note: the lanesense system operates with the similar behavior for a right lane departure when only the right lane marking has been detected. Left lane departure — both lanes detected • when the lanesense system is on, the lane lines turn from gray to white to indicate that both of the lane markings ...

  • Page 224

    • when the lanesense system senses a lane drift situa- tion, the left thick lane line and left thin line turn solid yellow. The lanesense indicator changes from solid green to solid yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. • for exa...

  • Page 225

    • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off) and the left thin line remains solid yellow. The lanesense indicator changes from solid yellow to flashing yellow. At this time torque is applied to ...

  • Page 226

    Changing lanesense status the lanesense system has settings to adjust the intensity of the torque warning and the warning zone sensitivity (early/late) that you can configure through the uconnect® system screen. Refer to “uconnect® settings” in “understanding your instrument panel” for further infor...

  • Page 227

    (evic) or driver information display (did) indicating the vehicle speed is too fast. The system will become active again if the vehicle speed is decreased to speeds less than approximately 6 mph (9 km/h). Parksense® sensors the four parksense® sensors, located in the rear fascia/ bumper, monitor the...

  • Page 228

    Parksense® display when the vehicle is in reverse, the evic/did will display the park assist ready system status. The system will indicate a detected obstacle by showing a single arc in one or more regions based on the obstacle’s distance and location relative to the vehicle. If an obstacle is detec...

  • Page 229

    Slow tone/solid arc slow tone/solid arc 3 understanding the features of your vehicle 227.

  • Page 230

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: fast tone/flashing arc continuous tone/flashing arc 228 understanding the features of y...

  • Page 231

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-59 in (200-150 cm) 59-47 in (150-120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) arcs — left none none none none none 2nd flashing 1st flashing arcs — center none 6th solid 5th solid 4t...

  • Page 232

    Note: parksense® will reduce the volume of the radio, if on, when the system is sounding an audio tone. Enabling and disabling parksense® parksense® can be enabled and disabled with the parksense® switch, located on the switch panel below the uconnect® display. When the parksense® switch is pushed t...

  • Page 233

    “driver information display (did)” for further informa- tion. When the shift lever is moved to reverse and the system is disabled, the evic/did will display the “parksense off” message for as long as the vehicle is in reverse. The parksense® switch led will be on when parksense® is disabled or requi...

  • Page 234

    Cleaning the parksense® system clean the parksense® sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could dam- age the sensors. Parksense® system usage precautions note: • ensure that the rear bumper is free of s...

  • Page 235

    System misinterpreting a close object as a sensor problem, causing the “parksense unavailable service required” message to be displayed in the evic/did. • parksense® should be disabled when the liftgate is in the open position and the vehicle is in reverse. An open liftgate could provide a false ind...

  • Page 236

    Warning! (continued) • before using parksense®, it is strongly recom- mended that the ball mount and hitch ball assem- bly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be...

  • Page 237

    • the automatic braking function may only be applied if the vehicle deceleration is not enough to avoid collid- ing with a detected obstacle. • the automatic braking function may not be applied fast enough for obstacles that move toward the rear of the vehicle from the left and/or right sides. • the...

  • Page 238

    Until the vehicle speed is increased to approximately 7 mph (11 km/h) or above. When in reverse and above the system’s operating speed, a warning will appear in the evic/did indicating the vehicle speed is too fast. The system will become active again if the vehicle speed is decreased to speeds less...

  • Page 239

    The parksense® warning screen is located within the electronic vehicle information center (evic) or driver information display (did). It provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle. Refer to “electronic vehicle...

  • Page 240

    Single 1/2 second tone/solid arc slow tone/solid arc 238 understanding the features of your vehicle.

  • Page 241

    Slow tone/solid arc fast tone/flashing arc 3 understanding the features of your vehicle 239.

  • Page 242

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: fast tone/flashing arc continuous tone/flashing arc 240 understanding the features of y...

  • Page 243

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-59 in (200-150 cm) 59-47 in (150-120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) arcs — left none none none none none 2nd flashing 1st flashing arcs — center none 6th solid 5th solid 4t...

  • Page 244

    Note: parksense® will reduce the volume of the radio, if on, when the system is sounding an audio tone. Front park assist when the vehicle is in drive or non-reverse for manual transmission, the parksense® warning screen will be displayed when an obstacle is detected. The system will indicate a dete...

  • Page 245

    No tone/solid arc no tone/flashing arc 3 understanding the features of your vehicle 243.

  • Page 246

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: fast tone/flashing arc continuous tone/flashing arc 244 understanding the features of y...

  • Page 247

    Warning alerts front distance (in/cm) greater than 47 in (120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) arcs — left none none none 2nd flashing 1st flashing arcs — center none 4th solid 3rd flashing 2nd flashing 1st flashing arcs — right none none non...

  • Page 248

    If the uconnect® system is equipped, chime volume settings will not be accessible from the evic/did. The chime volume settings include low, medium, and high. The factory default volume setting is medium. Parksense® will retain its last known configuration state through ignition cycles. Enabling and ...

  • Page 249

    “driver information display (did)” for further informa- tion. When the shift lever is moved to reverse and the system is disabled, the evic/did will display the “parksense off” message for as long as the vehicle is in reverse. The parksense® switch led will be on when parksense® is disabled or requi...

  • Page 250

    Car graphic will remain displayed for as long as the vehicle is in reverse. Refer to “electronic vehicle information center (evic) or ⬙ driver information dis- play (did)” for further information. If ⬙ parksense unavailable wipe rear sensors ⬙ or ⬙ parksense unavailable wipe front sen- sors ⬙ appear...

  • Page 251

    • when you move the shift lever to the reverse position and parksense® is turned off, the instrument cluster will display “parksense off” for as long as the vehicle is in reverse. • parksense®, when on, will reduce the volume of the radio when it is sounding a tone. • clean the parksense® sensors re...

  • Page 252

    Caution! (continued) the sensors will not be detected when they are in close proximity. • the vehicle must be driven slowly when using parksense® in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using parksense®. War...

  • Page 253

    Parksense® active park assist system — if equipped the parksense® active park assist system is intended to assist the driver during parallel and perpendicular park- ing maneuvers by identifying a proper parking space, providing audible/visual instructions, and controlling the steering wheel. The par...

  • Page 254

    • new vehicles from the dealership must have at least 30 miles accumulated before the parksense® active park assist system is fully calibrated and performs accu- rately. This is due to the system’s dynamic vehicle calibration to improve the performance of the feature. The system will also continuous...

  • Page 255

    The parksense® active park assist system will turn off automatically for any of the following conditions: • the parking maneuver is completed. • vehicle speed greater than 18 mph (30 km/h) when searching for a parking space. • vehicle speed greater than 5 mph (7 km/h) during active steering guidance...

  • Page 256

    • vehicle speed is less than 15 mph (25 km/h). Note: if the vehicle is driven above approximately 15 mph (25 km/h), the evic/did will instruct the driver to slow down. If the vehicle is driven above approxi- mately 18 mph (30 km/h), the system will cancel. The driver must then reactivate the system ...

  • Page 257

    • the driver needs to make sure that the selected parking space for the maneuver remains free and clear of any obstructions (e.G. Pedestrians, bicycles, etc.). • the driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/ clear of anything that may be o...

  • Page 258

    Once the vehicle is in position, you will be instructed to stop the vehicle’s movement and remove your hands from the steering wheel. Once the vehicle is at a standstill with your hands removed from the steering wheel, you will be instructed to place the shift lever into the reverse position. Space ...

  • Page 259

    When the driver places the shift lever into the reverse position, the system may instruct the driver to wait for steering to complete. The system will then instruct the driver to check their surroundings and move backward. Space found — shift to reverse check surroundings — wait for steering to comp...

  • Page 260

    Note: • it is the drivers responsibility to use the brake and accelerator during the semi-automatic parking maneu- ver. • when the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly. • the parksense® activ...

  • Page 261

    When the vehicle has reached the end of its backward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. Note: it is the drivers responsibility to use the brake and stop the vehicle. The driver should check their surroundings and be prepared to ...

  • Page 262

    When the driver places the shift lever into the drive position, the system may instruct the driver to wait for steering to complete. The system will then instruct the driver to check their surroundings and move forward. Check surroundings — shift to drive check surroundings — wait for steering to co...

  • Page 263

    When the vehicle has reached the end of its forward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. Note: it is the drivers responsibility to use the brake and stop the vehicle. The driver should check their surround- ings and be prepared to...

  • Page 264

    Once the vehicle is in a standstill condition, the driver will be instructed to place the shift lever into the re- verse position. When the driver places the shift lever into the reverse position, the system may instruct the driver to wait for steering to complete. The system will then instruct the ...

  • Page 265

    Your vehicle is now in the parallel park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to park. The ⬙ active parksense complete - check parking position ⬙ message...

  • Page 266

    Perpendicular parking space assistance operation/display when the parksense® active park assist system is enabled, the “active parksense searching - push ok to switch to perpendicular” message will show in the evic/did display. Push the ok button on the left side steering wheel switch to change your...

  • Page 267

    Note: • when searching for a parking space, use the turn signal indicator to select which side of the vehicle you want to perform the parking maneuver. The parksense® active park assist system will automati- cally search for a parking space on the passenger’s side of the vehicle if the turn signal i...

  • Page 268

    Once the vehicle is in position, you will be instructed to stop the vehicle’s movement and remove your hands from the steering wheel. Once the vehicle is at a standstill with your hands removed from the steering wheel, you will be instructed to place the shift lever into the reverse position. Space ...

  • Page 269

    When the driver places the shift lever into the reverse position, the system may instruct the driver to wait for steering to complete. The system will then instruct the driver to check their surroundings and move backward. Space found — shift to reverse check surroundings — wait for steering to comp...

  • Page 270

    Note: • it is the drivers responsibility to use the brake and accelerator during the semi-automatic parking maneu- ver. • when the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly. • the parksense® activ...

  • Page 271

    When the vehicle has reached the end of its backward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. Note: it is the drivers responsibility to use the brake and stop the vehicle. The driver should check their surround- ings and be prepared t...

  • Page 272

    When the driver places the shift lever into the drive position, the system may instruct the driver to wait for steering to complete. The system will then instruct the driver to check their surroundings and move forward. Check surroundings — shift to drive check surroundings — wait for steering to co...

  • Page 273

    When the vehicle has reached the end of its forward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. Note: it is the drivers responsibility to use the brake and stop the vehicle. The driver should check their surroundings and be prepared to s...

  • Page 274

    Once the vehicle is in a standstill condition, the driver will be instructed to place the shift lever into the re- verse position. When the driver places the shift lever into the reverse position, the system may instruct the driver to wait for steering to complete. The system will then instruct the ...

  • Page 275

    Your vehicle is now in the perpendicular park position. When the maneuver is complete, the driver will be in- structed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to park. The ⬙ active parksense complete - check parking position ⬙ ...

  • Page 276

    Caution! (continued) might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • the vehicle must be driven slowly when using the parksense® active park assist system in order to be able to stop in time w...

  • Page 277

    Warning! (continued) • before using the parksense® active park assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles beca...

  • Page 278

    Note: the parkview® rear back up camera has pro- grammable modes of operation that may be selected through the uconnect® system. Refer to “uconnect® settings” in “understanding your instrument panel” for further information. When the vehicle is shifted out of reverse (with camera delay turned off), ...

  • Page 279

    The following table shows the approximate distances for each zone: zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm) yellow 1 ft - 6.5 ft (30 cm - 2 m) green 6.5 ft or greater (2 m or greater) warning! Drivers must be careful when backing up even when using the parkview® rear back up...

  • Page 280

    Note: if snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Garage door opener — if equipped homelink® replaces up to three remote controls (hand- held transmitters) that operate devices such as g...

  • Page 281

    Before you begin programming homelink® ensure your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device ...

  • Page 282

    1. Place the ignition in the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light in view. 3. Push and hold the homelink® button you want to program while you push and hold the han...

  • Page 283

    Firmly push and release the “learn” or “train- ing” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the learn/train mode. Note: you have 30 seconds in which to initiate the next step after the learn button has been pushed. 6. Retu...

  • Page 284

    1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you would like to program while keeping the homelink® indicator light in view. 3. Simultaneously push and hold both the homelink® button you want to program and t...

  • Page 285

    3. Without releasing the button proceed with “program- ming a non-rolling code” step 2 and follow all remaining steps. Canadian/gate operator programming for programming transmitters in canada/united states that require the transmitter signals to “time-out” after several seconds of transmission. Can...

  • Page 286

    Note: • if the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the homelink® button is pushed. • to program the two remaining homelink® buttons, repeat each step for each remaining button. Do not erase the channels. If you unplugged the ...

  • Page 287

    To do this, push and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The homelink® universal transceiver is disabled when the vehicle security alarm is active. Troubleshooting tips if you are ha...

  • Page 288

    Warning! (continued) after 1982. Do not use a garage door opener without these safety features. Call toll-free 1-800-355-3515 or, on the internet at homelink.Com for safety information or assistance. General information this device complies with fcc rules part 15 and industry canada rss-210. Operati...

  • Page 289

    The power shade switches are located to the right be- tween the sun visors on the overhead console. Warning! • never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location (continued) power sunroof switches powe...

  • Page 290

    Warning! (continued) accessible to children. Do not leave the ignition of a vehicle equipped with keyless enter-n-go™ in the acc or on/run mode. Occupants, particu- larly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may resu...

  • Page 291

    Opening sunroof — manual mode a comfort stop position is a programmed automatic stop for the sunroof open position. The comfort stop position has been optimized to minimize wind buffeting. To open the sunroof, push and hold the switch rearward. The sunroof will stop automatically at the comfort stop...

  • Page 292

    Note: if the sunshade is in the closed position when the vent switch is pushed, the sunshade will automatically cycle to the halfway open position prior to the sunroof opening to the vent position. Opening power shade — express push the shade switch rearward and release it within one-half second and...

  • Page 293

    Closing power shade — manual mode to close the shade, push and hold the switch in the forward position. Any release of the switch will stop the movement and the shade will remain in a partially closed condition until the switch is pushed and held forward again. Pinch protect feature this feature wil...

  • Page 294

    Ignition off operation the power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. Note: ignition off time is programmable through the uconnect® system. Refer to “uconnec...

  • Page 295

    The front power outlet is located inside the storage area on the center stack of the instrument panel. In addition to the front power outlet, there is also a power outlet located in the storage area of the center console. A third fused 12 volt power outlet is located on the left quarter trim panel i...

  • Page 296

    Note: the rear cargo power outlet can be changed to “battery” powered all the time by switching the power outlet power distribution center panel fuse from fuse location f91 to f81. Rear cargo electrical power outlet fuse electrical power outlet fuse locations 1 — f75 fuse 20a yellow front power outl...

  • Page 297

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 298

    Power inverter — if equipped there is a 115 volt, 150 watt inverter outlet located on the back of the center console to convert dc current to ac current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 watts. Certain high-end video games, su...

  • Page 299

    The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. To avoid overloading the circuit, chec...

  • Page 300

    Your qi enabled mobile phone. Qi is a standard that uses magnetic induction to transfer power to your mobile device. Your mobile phone must be designed for qi wireless charging, be equipped with an aftermarket sleeve or equipped with a back plate from your mobile phone provider, or an online or loca...

  • Page 301

    Note: the mobile phone must be aligned around the qi logo for the led to transition from red to flashing green. 3. If the led does not transition from red to flashing green, and just turns off, pick up your mobile phone and reposition it on the charging pad. 4. Adjust the wireless charging pad mobil...

  • Page 302

    Note: the initial adjustment will only need to be done once as long as only one mobile phone is used. If a different mobile phone is used, the cradle will need to be readjusted. The led indicator will flash green while the mobile phone is charging. The qi enabled phone is able to function normally a...

  • Page 303

    Cupholders there are two cupholders for the front seat passengers, located in the center console. There are two cupholders for the rear seat passengers, located in the center armrest. Storage glove compartment the glove compartment is located on the passengers side of the instrument panel. Pull outw...

  • Page 304

    There is also an additional storage bin located above the instrument panel in the center of the dash. Console storage compartment some vehicles may be equipped with a wireless charging pad located in the upper portion of the center console. Refer to wireless charging pad-if equipped in this section ...

  • Page 305

    The center console has a storage area which can hold cell phones, pdas, and other small items. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Center console center console ...

  • Page 306

    Flip ’n stow™ front passenger seat storage — if equipped some models may be equipped with storage under the front passenger seat cushion. Pull upward on the seat cushion loop to open the storage compartment. Note: make sure that objects inside the bin do not interfere with the latch before closing t...

  • Page 307

    Warning! Be certain that the seat cushion is locked securely into position before using the seat. Otherwise, the seat will not provide the proper stability for passen- gers. An improperly latched seat cushion could cause serious injury. Cargo area features cargo load floor the cargo load floor syste...

  • Page 308

    Cargo tie-down hooks and loops the tie-downs located on the cargo area floor should be used to secure loads safely when the vehicle is moving. Cargo tie-down loops are located on the trim panels. Warning! • cargo tie-downs are not safe anchors for a child seat tether strap. In a sudden stop or accid...

  • Page 309

    Warning! (continued) • do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be- come a dangerous projectile in a sudden stop or accident. Rear storage bins the rear storage bins are located in the rear of the vehicle on the sides of the load floor. Rear s...

  • Page 310

    Rear window features rear window wiper/washer the rear wiper/washer controls are located on the wind- shield wiper/washer lever on the right side of the steering column. The rear wiper/washer is operated by rotating a switch, located at the middle of the lever. Rotate the center portion of the lever...

  • Page 311

    If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “park” position. Rear window defroster the rear window defroster button is located on the switch bank by the manual climate controls. Push this button to turn on the rear window defroster and t...

  • Page 312

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 313

    Caution! • to avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as pos- sible and secure the load appropriately. • long loads, which extend over the windshield, such as wood panels or surfboards, should be secured to...

  • Page 315: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .316 䡵 instrument cluster — base . . . . . . . . . .317 䡵 instrument cluster — premium . . . . . .318 䡵 instrument cluster descriptions . . . . .319 䡵 electronic vehicle information center (evic) . . . . . . ....

  • Page 316

    ▫ buttons on the touchscreen. . . . . . . . . . . . . .362 ▫ customer programmable features/personal settings — uconnect® 5.0 settings . . . . . . . . .362 ▫ customer programmable features/personal settings — uconnect® 8.4 personal settings . . .380 䡵 uconnect® radios — if equipped . . . . . . . .39...

  • Page 317

    ▫ basic voice commands. . . . . . . . . . . . . . . . . .431 ▫ radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .433 ▫ media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .434 ▫ phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .436 ▫ voice text reply . . . . ....

  • Page 318

    Instrument panel features 1 — air demister outlet 5 — instrument cluster 9 — passenger air bag 13 — start/stop ignition button 2 — air outlet 6 — electronic speed control 10 — glove compartment 14 — liftgate release button 3 — electronic vehicle informa- tion center (evic)/ driver infor- mation disp...

  • Page 319

    Instrument cluster — base 4 understanding your instrument panel 317.

  • Page 320

    Instrument cluster — premium 318 understanding your instrument panel.

  • Page 321

    Instrument cluster descriptions 1. Tachometer indicates the engine speed in revolutions per minute (rpm x 1000). 2. High beam indicator indicates that headlights are on high beam. 3. Front fog light indicator — if equipped this indicator will illuminate when the front fog lights are on. 4. Park/head...

  • Page 322

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 323

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. If brake failure is indicated, immediate repair is necessary. 6. Electroni...

  • Page 324

    If the abs light remains on or turns on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the brake warning light is not on. If the abs light is on, t...

  • Page 325

    Note: • the “esc off indicator light” and the “esc activation/malfunction indicator light” come on momentarily each time the ignition switch is turned to on/run. • each time the ignition is turned to on/run, the esc system will be on even if it was turned off previously. • the esc system will make b...

  • Page 326

    Or front passenger seat belt remains unbuckled, the seat belt indicator light will flash or remain on continuously. Refer to “occupant restraints” in “things to know before starting your vehicle” for further information. 14. Turn signal indicator the arrows will flash with the exterior turn signals ...

  • Page 327

    Maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicato...

  • Page 328

    16. Fuel gauge/fuel door reminder the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position. The fuel pump symbol points to the side of the vehicle where the fuel door is located. 17. Temperature gauge the temperature gauge shows engine coolant tempera- ...

  • Page 329

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “maintaining your vehicle”. Follow the warnings unde...

  • Page 330

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to...

  • Page 331

    The evic menu items consist of the following: • speedometer • vehicle info • driver assist • fuel economy • trip • audio • messages • screen setup the system allows the driver to select information by pushing the following buttons mounted on the steering wheel: • up arrow button push and release the...

  • Page 332

    • down arrow button push and release the down arrow button to scroll downward through the main menu and submenus. • right arrow button push and release the right arrow button to access the information screens or submenu screens of a main menu item. • back/left arrow button push and release the left ...

  • Page 333

    1. Electronic park brake failure — if equipped 2. Brake warning light 3. Engine temperature warning light 4. Evic display area 5. Lanesense — if equipped 6. Fuel gauge 7. Low fuel telltale 8. Rear axle lock indicator — if equipped 9. Reconfigurable yellow telltale display 10. Manual speed assist (ms...

  • Page 334

    Ok button. To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure. 1. Without pushing the brake pedal, push the engine start/stop button and cycle the ignition to the on/run position (do not start the engine). 2. Fully push the acceler...

  • Page 335

    • service adaptive cruise control telltale this light will illuminate when an acc is not operating and needs service. For further infor- mation, refer to “adaptive cruise control (acc)” in “understanding the features of your vehicle.” • low fuel telltale when the fuel level reaches approximately 3.0...

  • Page 336

    • lanesense failure telltale this telltale will illuminate to indicate that the lanesense departure has detected a failure. • diesel low diesel exhaust telltale — if equipped this telltale will illuminate to indicate the diesel exhaust fluid (def) is low. • rear axle locker telltale this light indic...

  • Page 337

    Evic red telltales this area will show reconfigurable red telltales. These telltales include: • charging system light this light shows the status of the electrical charg- ing system. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or i...

  • Page 338

    • door ajar this light will illuminate to indicate that one or more doors may be ajar. • oil pressure warning light this telltale indicates low engine oil pressure. If the light illuminates while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this ligh...

  • Page 339

    • electric power steering malfunction warning light this telltale is on when the electric power steering is not operating and needs service. • air bag warning light this light will illuminate for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light i...

  • Page 340

    Speedometer push and release the up or down arrow button until the speedometer menu item is highlighted in the evic. Push the ok button to change the speedometer scale from mph to km/h (or vice versa). Vehicle info (customer information features) push and release the up or down arrow button until th...

  • Page 341

    • transmission temp displays the actual transmission temperature. • oil temp displays the actual oil temperature. • oil life displays the remaining oil life. • battery voltage displays the actual battery voltage. Driver assist adaptive cruise control (acc) menu the evic displays the current acc syst...

  • Page 342

    The acc screen may display once again if any acc activity occurs, which may include any of the following: • distance setting change • system cancel • driver override • system off • acc proximity warning • acc unavailable warning • the evic will return to the last display selected after five seconds ...

  • Page 343

    Trip info push and release the up or down arrow button until the trip menu item is highlighted in the evic (toggle left or right to select trip a or trip b). The trip information will display the following: • distance • average fuel economy • elapsed time hold the ok button to reset feature informat...

  • Page 344

    Screen setup feature allows you to change what informa- tion is displayed in the instrument cluster as well as the location that information is displayed. Screen setup driver selectable items upper left • compass • outside temp (default setting) • time • range to empty (rte) • average mpg or l/100 k...

  • Page 345

    • current mpg or l/100 km • trip a distance • trip b distance • audio information • digital speed • none restore to defaults (restores all settings to default settings, outside temp ul, compass ur, center menu title) • ok • cancel driver information display (did) the driver information display (did)...

  • Page 346

    The did menu items consist of the following: • speedometer • vehicle info • driver assist • fuel economy • trip • audio • messages • screen setup • gear shift indicator (gsi) — if equipped • speed warning — if equipped the system allows the driver to select information by pushing the following butto...

  • Page 347

    • up arrow button push and release the up arrow button to scroll upward through the main menu and submenus. • down arrow button push and release the down arrow button to scroll downward through the main menu and submenus. • right arrow button push and release the right arrow button to access the inf...

  • Page 348

    Did display the did displays are located in the center portion of the cluster and consists of eight sections: 1. Lanesense — if equipped 2. Did selectable display area 3. Electronic park brake failure 4. Brake warning light 5. Driver information display (did) messages 6. Manual speed assist (msa) sp...

  • Page 349

    13. Odometer display/fuel gauge/temperature gauge/submenu area 14. Red reconfigurable telltale display oil change reset oil change due your vehicle is equipped with an engine oil change indicator system. The “oil change due” message will display in the did for five seconds after a single chime has s...

  • Page 350

    Did red telltales this area will show reconfigurable red telltales. These telltales include: • charging system light this light shows the status of the electrical charg- ing system. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or in...

  • Page 351

    • door ajar this light will turn on to indicate that one or more doors may be ajar. • oil pressure warning light this telltale indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turn...

  • Page 352

    • electric power steering malfunction warning light this telltale is on when the electric power steering is not operating and needs service. • air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is e...

  • Page 353

    • service stop/start system telltale — if equipped this telltale will turn on to indicate the stop/ start system is not functioning properly and service is required. • service adaptive cruise control telltale this light will turn on when a acc is not operating and needs service. For further infor- m...

  • Page 354

    • diesel wait to start telltale — if equipped the “wait to start” telltale will illuminate for approximately two seconds when the ignition is turned to the run position. It’s duration may be longer based on colder operating conditions. Vehicle will not initiate start until telltale is out. Refer to ...

  • Page 355

    • loose fuel filler cap this telltale will turn on to indicate that the fuel filler cap may be loose. Did selectable menu items push and release the up or down arrow buttons until the desired selectable menu item is displayed in the did. Follow the menu or submenu prompts as desired. Speedometer pus...

  • Page 356

    • tire psi is an information only function and cannot be reset. Push and release the left arrow button to return to the main menu. • refer to “tire pressure monitoring system (tpms)” under “starting and operating” for further informa- tion. 2. Coolant temperature displays the actual coolant temperat...

  • Page 357

    Adaptive cruise control ready when acc is activated but the vehicle speed setting has not been selected, the display will read “adaptive cruise control ready.” push and release the set + or the set- button (located on the steering wheel) and the following will display in the did: acc set when acc is...

  • Page 358

    Fuel economy push and release the up or down arrow button until the fuel economy menu item is highlighted in the did. Push and hold the ok button to reset feature. • range • average fuel economy • current fuel economy (mpg or l/100 km) trip info push and release the up or down arrow button until the...

  • Page 359

    Screen setup push and release the up or down arrow button until the screen setup menu displays in the did. Push and release the ok button to enter the sub-menus. The screen setup feature allows you to change what information is displayed in the instrument cluster as well as the location that informa...

  • Page 360

    Exhaust after-treatment system may never reach the conditions required to cleanse the filter to remove the trapped pm. If this occurs, the “exhaust filter xx% full safely drive at highway speeds to remedy” message will be displayed in the did. If this message is displayed, you will hear one chime to...

  • Page 361

    The after-treatment system. If this condition is not corrected and a dealer service is not performed, exten- sive exhaust after-treatment damage can occur. To correct this condition it will be necessary to have your vehicle serviced by your local authorized dealer. Note: failing to follow the oil ch...

  • Page 362

    Initiate start until telltale is out. Refer to “starting proce- dures” in “starting and operating” for further information. Note: the “wait to start” telltale may not illuminate if the intake manifold temperature is warm enough. Adblue® light this telltale will turn on to indicate the ad- blue® is l...

  • Page 363

    Buttons on the faceplate buttons on the faceplate are located below the uconnect® system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side of the climate controls in the center of the instru- ment panel. Turn the control knob to scroll...

  • Page 364

    Buttons on the touchscreen buttons on the touchscreen are accessible on the uconnect® display. Customer programmable features/personal settings — uconnect® 5.0 settings push the settings button on the faceplate or push the + more button, then the “settings” button on the touchscreen to display the m...

  • Page 365

    Note: when day or night is selected for the display mode, the usage of the parade mode feature will cause the radio to activate the display brightness day control even though the headlights are on. • display brightness with headlights on when in this display, you may select the overall screen bright...

  • Page 366

    On the touchscreen. Press the back arrow button on the touchscreen to return to the previous menu. • units when in this display, you may select to have the did, odometer, and navigation system (if equipped) changed between us and metric units of measure. Press “us” or “metric” to make your selection...

  • Page 367

    Voice after pressing the “voice” button on the touchscreen the following settings will be available: • voice response length when in this display, you may change the voice re- sponse length settings. To change the voice response length, press the “voice response length” button on the touchscreen and...

  • Page 368

    Safety & driving assistance after pressing the “safety & driving assistance” button on the touchscreen the following settings will be available: • forward collision warning (fcw) — if equipped the front collision warning (fcw) feature can be can be set to far, or set to near. The default status of f...

  • Page 369

    Lane departures. The ldw sensitivity can be set to provide either an “early,” “medium,” or “late” warning zone start point. For further information, refer to “lanesense warning (ldw)” in “understanding the features of your vehicle”. • lanesense strength — if equipped when this feature is selected, i...

  • Page 370

    The chime volume settings include “low,” “medium,” and “high.” the factory default volume setting is medium. • rear parksense® volume — if equipped rear park assist chime volume settings can be selected from the evic/did or uconnect® system (if equipped). The chime volume settings include “low,” “me...

  • Page 371

    Visual alert in the outside mirrors as well as an audible alert when the turn signal is on. When off is selected, the blind spot monitor (bsm) system is deactivated. To change the blind spot alert status, press the “off,” “lights” or “lights & chime” button on the touchscreen. Then press the back ar...

  • Page 372

    “on” or “off.” press the back arrow button on the touchscreen to return to the previous menu. • electric park brake service mode this feature provides a means for a technician or vehicle owner to utilize a vehicle integrated, menu driven sys- tem, to command the electric park brake retraction, to se...

  • Page 373

    Turned off if they were turned on by this feature. To make your selection, press the “lights w/wipers” button on the touchscreen and make your selection. Press the back arrow button on the touchscreen to return to the previous menu. • auto high beams — if equipped when this feature is selected, the ...

  • Page 374

    (24 km/h). To make your selection, press the “auto door locks” button on the touchscreen and select from “on” or “off.” press the back arrow button on the touchscreen to return to the previous menu. • auto unlock on exit when this feature is selected, all doors will unlock when the vehicle is stoppe...

  • Page 375

    • remote door unlock when “remote door unlock” is selected, you may choose from “driver” or “all.” select “all” to have all doors unlock with the first push of the key fob. Select “driver” to have the only the driver door open with the first push of the key fob. Note: passive entry — if equipped. If...

  • Page 376

    • power lift gate alert — if equipped this feature plays an alert when the power lift gate is raising or lowering. To make your selection, press the “power lift gate alert” button on the touchscreen and select from “on” or “off.” press the back arrow button on the touchscreen to return to the previo...

  • Page 377

    Equipped), and power outlets will remain active for up to 10 minutes after the ignition is cycled to off. Opening either front door will cancel this feature. To change the engine off power delay status press the “0 seconds,” “45 seconds,” “5 minutes” or “10 minutes” button on the touchscreen. Then p...

  • Page 378

    • perform compass calibration press the “calibration” button on the touchscreen to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass. When the vehicle is new, the compass may appear erratic until it is calibrated. You may also calibrate th...

  • Page 379

    Arrows to adjust, tap the “c” icon to readjust to the center. Press the back arrow/done button on the touchscreen to return to the previous menu. • speed adjusted volume this feature increases or decreases volume relative to vehicle speed. To change the speed adjusted volume press the “speed adjuste...

  • Page 380

    Phone/bluetooth® after pressing the “phone/bluetooth®” button on the touchscreen the following settings will be available: • paired phones this feature shows which phones are paired to the phone/bluetooth® system. For further information, refer to the uconnect® supplement manual. • paired audio sour...

  • Page 381

    Press the “subscription info” button on the touchscreen to access the subscription information screen. Write down the sirius id numbers for your receiver. To reactivate your service, either call the number listed on the screen or visit the provider online. Note: siriusxm travel link is a separate su...

  • Page 382

    Customer programmable features/personal settings — uconnect® 8.4 personal settings press the “apps” or the “controls” button on the touch- screen, then press the “settings” button on the touch- screen to display the menu setting screen. In this mode the uconnect® system allows you to access program-...

  • Page 383

    Note: when day or night is selected for the display mode, the usage of the parade mode feature will cause the radio to activate the display brightness day control even though the headlights are on. • display brightness with headlights on when in this display, you may select the brightness with the h...

  • Page 384

    • set language when in this display, you may select one of multiple languages (english / français / español) for all display nomenclature, including the trip functions and the naviga- tion system (if equipped). Press the “set language” button on the touchscreen, then select the desired language butt...

  • Page 385

    • navigation turn-by-turn displayed in cluster — if equipped when this feature is selected, to make your selection, press the “navigation turn-by-turn displayed in clus- ter” button on the touchscreen, until a check-mark ap- pears next to the setting, showing that setting has been selected. Press th...

  • Page 386

    Clock after pressing the “clock” button on the touchscreen the following settings will be available: • sync time with gps this feature will allow the radio to sync time with a gps signal. To change the sync time setting, press the “sync time with gps” button on the touchscreen until a check- mark ap...

  • Page 387

    Status setting press the “show time in status bar” button on the touchscreen until a check-mark appears next to setting, indicating that the setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu. Safety & driving assistance after pressing the “safet...

  • Page 388

    For further information, refer to “forward collision warning (fcw) with mitigation” in “understanding the features of your vehicle”. • lanesense warning — if equipped when this feature is selected, it sets the distance at which the steering wheel will provide feedback for potential lane departures. ...

  • Page 389

    The chime volume settings include “low,” “medium,” and “high.” the factory default volume setting is medium. • rear parksense® volume — if equipped rear park assist chime volume settings can be selected from the evic/did or uconnect® system (if equipped). The chime volume settings include “low,” “me...

  • Page 390

    Activated, the blind spot monitor (bsm) will show a visual alert in the outside mirrors as well as an audible alert when the turn signal is on. When off is selected, the blind spot monitor (bsm) system is deactivated. To change the blind spot alert status, press the “off,” “lights” or “lights & chim...

  • Page 391

    “rain sensing” button on the touchscreen, until a check- mark appears next to setting, showing that setting has been selected. Press the back arrow button on the touch- screen to return to the previous menu. • electric park brake service mode this feature provides a means for a technician or vehicle...

  • Page 392

    • headlights with wipers — if equipped when this feature is selected, and the headlight switch is in the auto position, the headlights will turn on ap- proximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by th...

  • Page 393

    With lock” button on the touchscreen, until a check-mark appears next to setting, showing that setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu, or push the back button on the faceplate. Doors & locks after pressing the doors & locks button on ...

  • Page 394

    Next to setting, indicating that the setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu. • sound horn with lock when this feature is selected, the horn will sound when the door locks are activated. To make your selection, press either the “off,” ...

  • Page 395

    Door is opened, the interior door lock/unlock switch can be used to unlock all doors (or use rke transmitter). • passive entry this feature allows you to lock and unlock the vehicles door(s) without having to press the remote keyless entry (rke) transmitter lock or unlock buttons. To make your selec...

  • Page 396

    Setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu, or push the back button on the faceplate. Auto-on comfort — if equipped after pressing the “auto-on comfort” button on the touchscreen the following settings will be available: • auto-on driver ...

  • Page 397

    Either front door will cancel this feature. To change the engine off power delay status press the “+” or “-” button to choose from “0 seconds,” “45 seconds,” “5 minutes,” or “10 minutes.” press the back arrow button on the touchscreen to return to the previous menu. • headlight off delay when this f...

  • Page 398

    • speed adjusted volume this feature increases or decreases volume relative to vehicle speed. To change the speed adjusted volume press the “off,” “1,” “2” or “3” button on the touchscreen. Press the back arrow button on the touchscreen to return to the previous menu. • surround sound — if equipped ...

  • Page 399

    • paired audio sources this feature shows which audio devices are paired to the phone/bluetooth® system. For further information, refer to the uconnect® supplement manual. Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touch- screen, the following settings will be ava...

  • Page 400

    Restore settings after pressing the “restore settings” button on the touchscreen the following settings will be available: • restore settings when this feature is selected it will reset the display, clock, audio, and radio settings to their default settings. To restore the settings to their default ...

  • Page 401

    System information after pressing the “system information” button on the touchscreen the following settings will be available: • system information when system information is selected, a system informa- tion screen will appear displaying the system software version. Uconnect® radios — if equipped fo...

  • Page 402

    Located in the front storage area, this feature allows an ipod® or external usb device to be plugged into the usb port. Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versions may not fully support the ipod® control features. Please visit apple’s webs...

  • Page 403

    Pushing the center button will make the radio switch between the various modes available (am/fm/sxm/ cd/aux, etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The following desc...

  • Page 404

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 405

    Regulatory and safety information usa/canada exposure to radio frequency radiation the radiated output power of the internal wireless radio is far below the fcc radio frequency exposure limits. Nevertheless, the wireless radio will be used in such a manner that the radio is 20 cm or further from the...

  • Page 406

    Note: • this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful inter- ference in a residential installation. This equipment generates, uses and c...

  • Page 407

    Front blower control there are several blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position. Temperature control use this control to regulate the tem- peratur...

  • Page 408

    Air conditioning operation push the a/c button to engage the air conditioning (a/c). A led will illuminate when the a/c system is engaged. Max a/c for maximum cooling, when max a/c is selected the a/c is turned on automatically and the air is recirculated. Note: a/c cannot be deselected when in max ...

  • Page 409

    Bi-level mode air is directed through the panel and floor outlets. Note: there is a difference in temperature (in any conditions other than full cold or full hot), between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort dur...

  • Page 410

    Recirculation control push this button to choose between outside air intake or recirculation of the air inside the vehicle. A led will illuminate when you are in recirculation mode. Only use the recirculation mode to temporarily block out any outside odors, smoke, or dust, and to cool the interior r...

  • Page 411

    Rotate the temperature control knob to the desired tem- perature. Also, make sure to select only panel, bi-level or floor modes. Windshield wiper de-icer — if equipped the windshield wiper de-icer is a heating element lo- cated at the base of the windshield. The windshield wiper de-icer operates aut...

  • Page 412

    Manual climate controls with touchscreen — if equipped buttons on your uconnect® faceplate the buttons on the faceplate are located below the uconnect® screen. Buttons on your uconnect® touchscreen the buttons on the touchscreen are accessible on the uconnect® system screen. Uconnect® manual climate...

  • Page 413

    Button descriptions (applies to both the buttons on your faceplate and the buttons on your touchscreen) 1. Max a/c button push and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manua...

  • Page 414

    4. Front defrost button push and release to change the current airflow setting to defrost mode. The indicator illuminates when this fea- ture is on. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level will increase. Use defrost mode wit...

  • Page 415

    Automatic mode to switch to manual operation. The speeds can be selected using either the blower control knob on the faceplate or buttons on the touchscreen as follows: blower control knob on the faceplate the blower speed increases as you turn the blower control knob clockwise from the lowest blowe...

  • Page 416

    Note: bi-level mode is designed under comfort con- ditions to provide cooler air out of the panel outlets and warmer air from the floor outlets. • floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. • mix mode air come...

  • Page 417

    11. Temperature control (uconnect® 5.0) press the temperature button on the touchscreen to regu- late the temperature of the air inside the passenger com- partment. Moving the temperature bar into the red area, indicates warmer temperatures. Moving the temperature bar into the blue area indicates co...

  • Page 418

    Uconnect® 5.0 automatic temperature controls — buttons on your touchscreen uconnect® 8.4 automatic temperature controls — buttons on your touchscreen 416 understanding your instrument panel.

  • Page 419

    Button descriptions (applies to both the buttons on your faceplate and the buttons on your touchscreen) 1. Max a/c button press and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manu...

  • Page 420

    6. Rear defrost button press and release this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 10 minutes. For each additional press of ...

  • Page 421

    7. Passenger temperature control up button (uconnect® 8.4 only) provides the passenger with independent temperature control. Push the button on the faceplate for warmer temperature settings or on the touchscreen, press and slide the button on the touchscreen temperature bar towards the red arrow but...

  • Page 422

    Speeds can be selected using either the blower control knob on the faceplate or buttons on the touchscreen as follows: blower control knob on the faceplate the blower speed increases as you turn the blower control knob clockwise from the lowest blower setting. The blower speed decreases as you turn ...

  • Page 423

    • floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. • mix mode air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. 12. Climate control off button press ...

  • Page 424

    15. Temperature control (uconnect® 5.0 only) press the temperature button on the touchscreen to regulate the temperature of the air inside the passenger compartment. Moving the temperature bar into the red area, indicates warmer temperatures. Moving the tem- perature bar into the blue area indicates...

  • Page 425

    In max a/c, the blower level and mode position can be adjusted to desired user settings. Pushing other settings will cause the max a/c operation to switch to the selected setting and cause max a/c to exit. Recirculation when outside air contains smoke, odors, or high humidity, or if rapid cooling is...

  • Page 426

    Windshield wiper de-icer — if equipped the windshield wiper de-icer is a heating element lo- cated at the base of the windshield. The windshield wiper de-icer operates automatically once the following conditions are met: • activation by front defrost the wiper de-icer activates automatically during ...

  • Page 427

    3. When the system is set up for your comfort level, it is not necessary to change the temperature. You will experience the greatest efficiency by simply allowing the system to function automatically. Note: • it is not necessary to move the temperature settings. The system automatically adjusts the ...

  • Page 428

    Note: each of these features operates independently from each other. If any feature is controlled manually, tempera- ture control will continue to operate automatically. Operating tips note: refer to the chart at the end of this section for suggested control settings for various weather conditions. ...

  • Page 429

    Window fogging interior fogging on the windshield can be quickly re- moved by turning the mode selector to defrost. The defrost/floor mode can be used to maintain a clear windshield and provide sufficient heating. If side win- dow fogging becomes objectionable, increase blower speed to improve airfl...

  • Page 430

    Control setting suggestions for various weather conditions 428 understanding your instrument panel.

  • Page 431

    Uconnect® voice recognition quick tips introducing uconnect® start using uconnect® voice recognition with these helpful quick tips. It provides the key voice commands and tips you need to know to control your uconnect® 5.0 or 8.4a/8.4an system. Key features: • 5” touchscreen • three buttons on eithe...

  • Page 432

    If you see the icon on your touchscreen, you have the uconnect® 8.4an system. If not, you have a uconnect® 8.4a system. Get started all you need to control your uconnect® system with your voice are the buttons on your steering wheel. 1. Visit uconnectphone.Com to check mobile device and feature comp...

  • Page 433

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect® system. Push the vr button . After the beep, say ѧ • cancel to stop a current voice session • help to hear a list of suggested voice commands • repeat to listen to the system prompts again notice...

  • Page 434

    Uconnect® 5.0 uconnect® 8.4a/8.4an 432 understanding your instrument panel.

  • Page 435

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio® stations you would like to hear. (sub- scription or included siriusxm satellite radio® trial required.) push the vr button . After the beep, say ѧ • tune to ninety-five-point-five fm • tune to satellite channel hits 1 tip...

  • Page 436

    Media uconnect® offers connections via usb, sd, bluetooth® and auxiliary ports (if equipped). Voice operation is only available for connected usb and ipod® devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands a...

  • Page 437

    Uconnect® 5.0 media uconnect® 8.4a/8.4an media 4 understanding your instrument panel 435.

  • Page 438

    Phone making and answering hands-free phone calls is easy with uconnect®. When the phonebook button is illumi- nated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Push the phone button . After the beep, say one of the foll...

  • Page 439

    Voice text reply uconnect® will announce incoming text messages. Push the phone button and say listen. (must have com- patible mobile phone paired to uconnect® system.) 1. Once an incoming text message is read to you, push the phone button . After the beep, say: “reply.” 2. Listen to the uconnect® p...

  • Page 440

    Pre-defined voice text reply responses yes. Stuck in traffic. See you later. No. Start without me. I’ll be late. Okay. Where are you? I will be ber> minutes late. Call me. Are you there yet? I’ll call you later. I need directions. See you in of minutes. I’m on my way. Can’t talk right now. I’m lost....

  • Page 441

    Navigation (8.4a/8.4an) the uconnect® navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. (navigation is optional on the uconnect® 8.4a system. See your dealer to activate navigation at any time.) 1. To enter a destination, push...

  • Page 442

    Uconnect® access* (8.4a/8.4an) an included trial and/or subscription is required to take advantage of the uconnect® access services in the next section of this guide. To register with uconnect® access, press the apps button on the 8.4-inch touchscreen to get started. Detailed registration instructio...

  • Page 443

    9-1-1 call theft alarm notification remote door lock/unlock stolen vehicle assistance remote vehicle start** remote horn and lights yelp® search voice texting roadside assistance call wi-fi hotspot*** **if vehicle is equipped. ***extra charges apply. Register (8.4a/8.4an) 1. Press the apps button on...

  • Page 444

    Mobile app (8.4a/8.4an) securely link your mobile device to your vehicle with the uconnect® access app. Once you have downloaded the app, you may start your vehicle or lock it from virtually any distance. (vehicle must be properly equipped with factory-installed remote start.) download the uconnect®...

  • Page 445

    2. On the dashboard page, enter your mobile phone number to receive a link to download the app on your mobile device. Or go to itunes®, or google play, and search for the uconnect® access app. 3. To activate the app, enter your mopar owner connect user name and password and log in. Your vehicle is t...

  • Page 446

    2. Press the “all apps” button on the touchscreen. 3. Press the “yelp” button on the touchscreen. 4. Once the yelp® home screen appears on the touch- screen, push the vr button , then say: “yelp search.” 5. Listen to the system prompts and after the beep, tell uconnect® the place or business that yo...

  • Page 447

    Siriusxm travel link™ (8.4a/8.4an) need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? Siriusxm travel link™ is a suite of services that brings a wealth of information right to your uconnect® 8.4an system. (not available for 8.4a system.) push...

  • Page 448

    Additional information © 2015 fca us llc. All rights reserved. Mopar and uconnect are registered trademarks and mopar owner connect is a trademark of fca us llc. Android is a trademark of google inc. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. Yelp, yelp logo, yelp...

  • Page 449: Starting And Operating

    Starting and operating contents 䡵 starting procedures — gasoline engines . . . . . . . . . . . . . . . . . . . . . . . . . . . .452 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .452 ▫ extreme cold weather (below –20°f or −29°c) . . . . . . . . . . . . . . . .453 ▫ extended park start...

  • Page 450

    ▫ brake/transmission shift interlock system . . .463 ▫ fuel economy (eco) mode . . . . . . . . . . . . . .463 ▫ nine-speed automatic transmission . . . . . . . .463 ▫ gear ranges . . . . . . . . . . . . . . . . . . . . . . . . .465 䡵 four-wheel drive operation . . . . . . . . .473 ▫ 1-speed four-whe...

  • Page 451

    ▫ brake service mode . . . . . . . . . . . . . . . . . . . .495 䡵 brake system . . . . . . . . . . . . . . . . . . . . . . .497 䡵 electronic brake control system . . . .498 ▫ anti-lock brake system (abs) . . . . . . . . . . . .498 ▫ traction control system (tcs) . . . . . . . . . . . .500 ▫ brake as...

  • Page 452

    ▫ tire types . . . . . . . . . . . . . . . . . . . . . . . . . . .535 ▫ run flat tires — if equipped . . . . . . . . . . . . .537 ▫ spare tires — if equipped . . . . . . . . . . . . . . .537 ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . .539 ▫ tread wear indicators . . . . . . . . . ...

  • Page 453

    ▫ selection of engine oil for flexible fuel vehicles (e-85) and gasoline vehicles . . . . . . .564 ▫ starting . . . . . . . . . . . . . . . . . . . . . . . . . . . .565 ▫ cruising range . . . . . . . . . . . . . . . . . . . . . . .565 ▫ replacement parts . . . . . . . . . . . . . . . . . . . .565 ▫ ...

  • Page 454

    Starting procedures — gasoline engines before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle...

  • Page 455

    Within 10 seconds, cycle the ignition switch to the lock/off position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Tip start feature cycle the ignition switch to start position and release it as soon as the starter engages. The starter motor will continue to run, but will aut...

  • Page 456

    Caution! To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time. Wait 10 to 15 seconds before trying again. If engine fails to start warning! • never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start...

  • Page 457

    Starter engages. The starter motor will disengage auto- matically in 10 seconds. Once this occurs, release the accelerator pedal, cycle the ignition to the lock posi- tion, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Caution! To prevent damage to the starter, wait 10 to 15 se...

  • Page 458

    • the vehicle must be completely stopped. • the shifter must be in a forward gear and the brake pedal depressed. The engine will shut down, the tachometer will move to the zero position and the stop/start telltale will illumi- nate indicating you are in autostop. Customer settings will be maintained...

  • Page 459

    Other factors which can inhibit autostop include: • fuel level. • accelerator pedal input. • engine temp too high. • 5 mph threshold not achieved from previous au- tostop. • steering angle beyond threshold. • acc is on and speed is set. It may be possible for the vehicle to be driven several times w...

  • Page 460

    • stop/start off switch is pressed. • a stop/start system error occurs. • 4wd system is put into 4lo mode. Conditions that force an application of the electric park brake while in autostop mode: • the drivers door is open and brake pedal released. • the drivers door is open and the drivers seat belt...

  • Page 461

    2. The “stop/start off” message will appear in electronic vehicle information center (evic) or driver information display (did). Refer to “electronic vehicle information center (evic)” or “driver infor- mation display (did)” in “understanding your in- strument panel” for further information. 3. At t...

  • Page 462

    For ambient temperatures below 0°f (-18°c), the engine block heater is recommended. For ambient temperatures below -20°f (-29°c), the engine block heater is required. The engine block heater cord is routed under the hood, behind to the driver’s side headlamp. Follow the steps below to properly use t...

  • Page 463

    Automatic transmission warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or...

  • Page 464

    Warning! (continued) • do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition (in a vehicle equipped with keyless enter-n-go™) in the acc or on/run position. A child could operate power windows, other controls, or move the vehicle. Ca...

  • Page 465

    Brake/transmission shift interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the shift lever in park unless the brakes are applied. To shift the transmission out of park, the ignition switch must be turned to the on/run position (engine runnin...

  • Page 466

    Speeds (refer to ⬙ brake/transmission shift interlock sys- tem ⬙ in this section). Select the drive range for normal driving. The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehi...

  • Page 467

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 468

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to mo...

  • Page 469

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 470

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 471

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 472

    If the transmission temperature exceeds normal operat- ing limits, the transmission controller may modify the transmission shift schedule, reduce engine torque, and/or expand the range of torque converter clutch engagement. This is done to prevent transmission dam- age due to overheating. If the tra...

  • Page 473

    To operate. The malfunction indicator light (mil) may be illuminated. Limp home mode allows the vehicle to be driven to an authorized dealer for service without dam- aging the transmission. In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing t...

  • Page 474

    Moving the shift lever to the ers position (beside drive) will activate ers mode, display the current gear in the instrument cluster, and maintain that gear as the top available gear. Once in ers mode, moving the shift lever forward (-) or rearward (+) will change the top available gear. To exit ers...

  • Page 475

    Note: the torque converter clutch will not engage until the transmission fluid is warm (usually after 1 to 3 miles [2 to 5 km] of driving). Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting properly when cold, this ...

  • Page 476

    Caution! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit. 2-speed four-wheel drive (4x4) — if equipped the four-wheel drive is fully automatic in the normal driving mode. The selec-terrain buttons ...

  • Page 477

    • neutral when additional traction is required, the 4wd low range position can be used to provide an additional gear reduction which allows for increased torque to be deliv- ered to both the front and rear wheels. 4wd low is intended for loose, slippery road surfaces only. Driving in 4wd low on dry,...

  • Page 478

    Warning! You or others could be injured or killed if you leave the vehicle unattended with the power transfer unit in the neutral (n) position without first fully engaging the parking brake. The neutral (n) position disengages both the front and rear drive shafts from the powertrain and will allow t...

  • Page 479

    Note: if shift conditions/interlocks are not met a mes- sage will flash from the electronic vehicle information center (evic)/driver information display (did) with instructions on how to complete the requested shift. Refer to “electronic vehicle information center (evic)/ driver information display ...

  • Page 480

    Note: • if shift conditions/interlocks are not met, a message will flash from the electronic vehicle information cen- ter (evic)/driver information display (did) with in- structions on how to complete the requested shift. Refer to “electronic vehicle information center (evic)/ driver information dis...

  • Page 481

    3. Turn the ignition switch to the on/run position, but do not start the engine. 4. Press and hold the brake pedal. 5. Shift the transmission into neutral. 6. Using a ballpoint pen or similar object, press and hold the recessed power transfer unit neutral (n) button (located by the selector switch) ...

  • Page 482

    10. Release the brake pedal for five seconds and ensure that there is no vehicle movement. 11. Shift the transmission to neutral. 12. Apply the parking brake. 13. Shift the transmission into park, turn the engine off, and remove the key fob. Repeat steps 1-7 to shift out of neutral. Rear electronic ...

  • Page 483

    2. The ignition switch in the on position and the engine running. 3. To disengage rear e-locker, press the rear lock button once. Note: • it may also be necessary to drive slowly steering back and forth to complete engagement and disengagement of the e-locker. • when engaging rear e-locker, the indi...

  • Page 484

    Selec-terrain™ description selec-terrain™ combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance for all terrains. Rotate the selec-terrain™ knob to select the desired mode. Selec-terrain™ offers the following modes: • auto — fully automati...

  • Page 485

    • snow — tuning set for additional stability in inclem- ent weather. Use on and off road on loose traction surfaces such as snow. When in snow mode (depend- ing on certain operating conditions), the transmission may use second gear (rather than first gear) during launches, to minimize wheel slippage...

  • Page 486

    Electronic vehicle information center (evic)/driver information display (did) display messages when the appropriate conditions exist, a message will appear in the evic/did display. Refer to “electronic vehicle information center (evic)/driver information display (did)” in “understanding your instrum...

  • Page 487

    Driving through water although your vehicle is capable of driving through water, there are a number of precautions that must be considered before entering the water: caution! When driving through water, do not exceed 5 mph (8 km/h). Always check water depth before entering as a precaution, and check...

  • Page 488

    Maintenance after driving through deep water, inspect your vehicle fluids and lubricants (engine, transmission, power trans- fer unit and rear drive module) to assure they have not been contaminated. Contaminated fluids and lubricants (milky, foamy in appearance) should be flushed/changed as soon as...

  • Page 489

    Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle. Always back straight down a hill in reverse gear carefully. Never back down a hill in neutral using only the ...

  • Page 490

    After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect...

  • Page 491

    • if you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material. Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation. Power steering the electric power steering system will give you good...

  • Page 492

    Extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system. You will lose power steering assistance momentarily until the over temperature condition no longer exists. Once driving conditions are safe, then pull over and let vehicle idle for ...

  • Page 493

    To apply the parking brake manually, pull up on the switch momentarily. You may hear a slight whirring sound from the back of the vehicle while the parking brake engages. Once the parking brake is fully engaged, the brake warning lamp in the instrument cluster and an indicator on the switch will ill...

  • Page 494

    The parking brake will release automatically when the ignition switch is on, the transmission is in drive or reverse, the driver seat belt is buckled, and an attempt is made to drive away. To release the park brake manually, the ignition switch must be in the on/run position. Put your foot on the br...

  • Page 495

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 496

    Will sound. The rear stop lamps will also be illuminated automatically while the vehicle remains in motion. To disengage the parking brake while the vehicle is in motion, release the switch. If the vehicle is brought to a complete stop using the parking brake, when the vehicle reaches approximately ...

  • Page 497

    Safehold safehold is a safety feature of the electric park brake system that will engage the park brake automatically if the vehicle is left unsecured while the ignition switch is in run. For automatic transmissions, the park brake will automati- cally engage if all of the following conditions are m...

  • Page 498

    When servicing your rear brakes, it may be necessary for you or your technician to push the rear piston into the rear caliper bore. With the electric parking brake system, this can only be done after retracting the electric parking brake actuator. Fortunately, actuator retraction can be done easily ...

  • Page 499

    Brake system your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still function. However, there will be some loss of overall braking effectiveness. This will be evident by increased pedal travel during ...

  • Page 500

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system commonly referred to as esc. This system includes anti-lock brake system (abs), traction control system (tcs), brake assist system (bas), hill start assist (hsa), electronic roll mitigation (erm...

  • Page 501

    The abs pump motor runs during the self-test at 12 mph (20 km/h) and during an abs stop. The pump motor makes a low humming noise during operation, which is normal. Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping di...

  • Page 502

    • do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping dis- tances, or brake damage. • when descending mountains or hills, repeated braking can cause brake fade with loss of braking control. Avoid repea...

  • Page 503

    Or the “full off” mode. Refer to “electronic stability control (esc)” in this section for further information. Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing...

  • Page 504

    Applies the appropriate brake and may also reduce engine power to lessen the chance that wheel lift will occur. Erm will only intervene during very severe or evasive driving maneuvers. Erm can only reduce the chance of wheel lift occurring during severe or evasive driving maneuvers. It cannot preven...

  • Page 505

    The following conditions must be met in order for hsa to activate: • the vehicle must be stopped. • the vehicle must be on a 7% (approximate) grade or greater hill. • the gear selection must match vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle backing uphill is in ...

  • Page 506

    Towing with hsa hsa will provide assistance during acceleration on an incline while towing a trailer. Warning! • if you use a trailer brake controller with your trailer, the trailer brakes may be activated and deactivated with the brake switch. If so, there may not be enough brake pressure to hold b...

  • Page 507

    Hill descent control (hdc) — if equipped hdc is intended for low speed off road driving while in 4wd low range. Hdc maintains vehicle speed while descending hills during various driving situations. Hdc controls vehicle speed by actively controlling the brakes. Hdc has three states: 1. Off (feature i...

  • Page 508

    Activating hdc once hdc is enabled it will activate automatically if driven down a grade of sufficient magnitude (greater than approximately 8%). The set speed for hdc is selectable by the driver, and can be adjusted by using the gear shift lever. The following summarizes the hdc set speeds: • p = n...

  • Page 509

    Driver override: the driver may override hdc activation with throttle or brake application at anytime. Deactivating hdc hdc will be deactivated but remain available if any of the following conditions occur: • driver overrides hdc set speed with throttle or brake application. • vehicle speed exceeds ...

  • Page 510

    Feedback to the driver: the instrument cluster has an hdc icon and the hdc switch has an led which offer feedback to the driver about the state hdc is in. • the cluster icon and switch lamp will illuminate and remain on solid when hdc is enabled or activated. This is the normal operating condition f...

  • Page 511

    Selec speed control (ssc) — if equipped ssc is intended for off road driving in 4wd low range only. Ssc maintains vehicle speed by actively controlling engine torque and brakes. Ssc has three states: 1. Off (feature is not enabled and will not activate) 2. Enabled (feature is enabled and ready but a...

  • Page 512

    Activating ssc once ssc is enabled it will activate automatically once the following conditions are met: • driver releases throttle • driver releases brake • transmission is in any selection other than p • vehicle speed is below 20 mph (32 km/h) the set speed for ssc is selectable by the driver, and...

  • Page 513

    Note: • these ssc default set speeds are dependent on hill grade. That is the steeper the grade of the hill the vehicle travels on the lower the values of the set speed will be for all listed gears, with the minimal value being .6 mph (1 km/h). • during ssc the ers +/- shifter input is used for ssc ...

  • Page 514

    • the vehicle is driven greater than 20 mph (32 km/h) for greater than 70 seconds. • the vehicle is driven greater than 40 mph (64 km/h) (ssc exits immediately). Feedback to the driver: the instrument cluster has an ssc icon and the ssc switch has an led which offer feedback to the driver about the ...

  • Page 515

    Esc uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match the intended path, esc applies the brake of the appro- priate wheel to assist in counteracting the oversteer or understeer condi...

  • Page 516

    Esc operating modes depending upon model and mode of operation, the esc system has up to three operating modes: “esc on” “partial off,” and “full off.” esc on — two-wheel drive vehicles and four-wheel drive vehicles in 2wd and 4wd high range this is the normal operating mode for esc when oper- ating...

  • Page 517

    Warning! • when in “partial off” mode, the tcs functionality of esc, (except for the limited slip feature de- scribed in the tcs section), has been disabled and the “esc off indicator light” will be illuminated. When in “partial off” mode, the engine power reduction feature of tcs is disabled, and t...

  • Page 518

    Running. After five seconds, the ⬙ esc off ⬙ indicator light will illuminate and an “esc off” message will appear in the odometer. In this mode, esc and tcs are turned off (except for the “limited slip” feature described in the tcs section) until the vehicle reaches a speed of 40 mph (64 km/h). At s...

  • Page 519

    • the “esc off” message will display and a chime will sound when the shift lever is moved from any position to the park position and then moved out of the park position. This will occur even if the message was cleared previously. Esc activation/malfunction indicator light and esc off indicator light...

  • Page 520

    • each time the ignition is turned on, the esc system will be on even if it was turned off previously. • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation. The ⬙ ...

  • Page 521

    Warning! If the tsc activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Ready alert braking (rab) ready alert braking may reduce the time required to reach full braking during emergency braking situations. It antic...

  • Page 522

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 523

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 524

    Example: r = construction code – ⬙ r ⬙ means radial construction, or – ⬙ d ⬙ means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating t...

  • Page 525

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 526

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 527

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 528

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) 526 starting and operating.

  • Page 529

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. Example tire placard location (b-pillar) tire and loading information p...

  • Page 530

    4. Cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and co...

  • Page 531

    3. Subtract the combined weight of the driver and pas- sengers from xxx lbs or xxx kg. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the ...

  • Page 532

    530 starting and operating.

  • Page 533

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 534

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 535

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Cau...

  • Page 536

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 537

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed symbol). Tire ...

  • Page 538

    Warning! Do not use summer tires in snow/ice conditions. You could lose vehicle control, resulting in severe injury or death. Driving too fast for conditions also creates the possibility of loss of vehicle control. Snow tires some areas of the country require the use of snow tires during the winter....

  • Page 539

    Run flat tires — if equipped run flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the run flat mode. A run flat mode occurs when the tire inflation pressure is of/or below 14 psi...

  • Page 540

    Rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact spare tire — if equipped the compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looki...

  • Page 541

    Front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the temporary use full size spare tire needs to be replaced. Since it is not the same as your original equipment tire, replace (or repair) the original...

  • Page 542

    Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels fast...

  • Page 543

    Worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. Life of tire the service life of a tire is dependent upon varying factors including, but not limited to: • driving style. • tire pressure - improper cold tire inflati...

  • Page 544

    Information placard or the vehicle certification label for the size designation of your tire. The load index and speed symbol for your tire will be found on the original equipment tire sidewall. See the tire sizing chart ex- ample found in the tire safety information section of this manual for more ...

  • Page 545

    Warning! (continued) • failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Tire chains (tractio...

  • Page 546

    Four wheel drive (4wd) non-trailhawk models with a two-speed power takeoff unit • the use of 7mm snow chains is permitted with 225/ 65r17 and 225/60r18 tires. Four wheel drive (4wd) trailhawk models • the use of 9mm snow chains is permitted with the use of 225/65r17 tires on size 17 x 7.5 et31 wheel...

  • Page 547

    Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device clearance be- tween tires and other suspension components, it is important that only traction devices in good condi- tion are used. Broken devices can cause serious damage. S...

  • Page 548

    Type tires. Rotation will increase tread life, help to main- tain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Refer to the “maintenance schedule” for the proper maintenance intervals. The reasons for any rapid or unusual wear should be corrected prior to rotation bein...

  • Page 549

    Caution! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause (continued) caution! (continued) damage to the power transfer unit. Tire rotation schedule should be followed to balance tire wear. Tir...

  • Page 550

    Into the tire sidewall. Refer to “tires – general informa- tion” in “starting and operating” for information on how to properly inflate the vehicle’s tires. The tire pressure will also increase as the vehicle is driven. This is normal and there should be no adjustment for this increased pressure. Th...

  • Page 551

    The tire pressure to rise to approximately 28 psi (193 kpa), but the “tire pressure monitoring telltale light” will still be on. In this situation, the “tire pressure monitoring telltale light” will turn off only after the tires are inflated to the vehicle’s recommended cold placard pressure value. ...

  • Page 552

    Note: • the tpms is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly underinflated tire causes the tire to overheat a...

  • Page 553

    Tire pressure monitoring low pressure warnings the “tire pressure monitoring telltale light” will illuminate in the instrument cluster, a “low tire pressure” message will display in the instrument cluster, an ⬙ inflate to xx ⬙ message will be displayed and a chime will sound when tire pressure is lo...

  • Page 554

    1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpms sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the v...

  • Page 555

    Off, as long as no tire pressure is below the low- pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. Premium system — if equipped the tire pressure monitor syst...

  • Page 556

    Should this occur, you should stop as soon as possible and inflate the tires with low pressure (those in a different color in the evic/did graphic) to the vehicle’s recommended cold placard pressure value as shown in the ⬙ inflate to xx ⬙ message. Once the system receives the updated tire pressures,...

  • Page 557

    Seconds and then display dashes (- -) in place of the pressure value to indicate which sensor is not being received. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” ...

  • Page 558

    Vehicles with matching full-size spare 1. The matching full size spare wheel and tire assembly has a tire pressure monitoring sensor that can be monitored by the tpms. 2. If you install the full size spare in place of a road tire that has a pressure below the low-pressure warning limit, a chime will...

  • Page 559

    Graphic in the evic/did will still display a different color pressure value and an ⬙ inflate to xx ⬙ message. 3. After driving the vehicle for up to 20 minutes above 15.5 mph (25 km/h), the “tpms telltale light” will flash on and off for 75 seconds and then remain on solid. In addition, the evic/did...

  • Page 560

    The tpm sensors are regulated under one of the follow- ing licenses: united states gq4-61t canada 1470a-42t fuel requirements 2.4l engine these engines are designed to meet all emis- sions regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasol...

  • Page 561

    Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and should be reported to your dealer immediately. Engine damage resulting from operating with a heavy spark knock may not be covered by the new vehicle warranty...

  • Page 562

    Are not the responsibility of the manufacturer and may void or not be covered under new vehicle limited warranty. E-85 usage in non-flex fuel vehicles non-flex fuel vehicles (ffv) are compatible with gaso- line containing up to 10% ethanol (e10). Gasoline with higher ethanol content may void the new...

  • Page 563

    Without mmt be used in your vehicle. The mmt content of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether the gasoline contains mmt. Mmt is prohibited in federal and california reformulated gasoline. Materials added to fuel all gasoline sold...

  • Page 564

    Caution! (continued) • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle perfor- mance problems resulting from the use of such fuels or additives is not the respon...

  • Page 565

    Warning! (continued) time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Flexible fuel (2.4l engine only) — if equipped e-85 general information the information in this section is unique for flexible fuel vehicles only. ...

  • Page 566

    Fuel requirements if your vehicle is e-85 compatible, it will operate on unleaded gasoline with any octane rating, or solely e-85 fuel, or any mixture of these fuels. For best results, avoid fueling patterns alternating between e-85 and unleaded gasoline. When switching fuel types: • add 5 gallons (...

  • Page 567

    Fca us material standard ms-6395. It is recommended that engine oils that are api certified and meet the requirements of material standard ms-6395 be used. Ms-6395 contains additional requirements, developed during extensive fleet testing, to provide additional pro- tection to fca us llc engines. St...

  • Page 568

    Maintenance caution! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect drivability. Adding fuel the gas cap is located behind the fuel filler door, on the passenger side of the vehicle. If the gas cap is lost or damaged, be sure the...

  • Page 569

    Note: • in certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button. Do not pry on the door. • when the fuel nozzle “clicks” or shuts off, the fuel tank is ...

  • Page 570

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel filler cap. A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermar- ket cap can cause the “malfunction indicator light (mil)” to illuminate, due to fuel v...

  • Page 571

    2. Remove access door located on right interior trim panel for release cable with the tip of your key. 3. Grab the release cable tether and pull up to release the fuel filler door. Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly...

  • Page 572

    Information (evic) or ⬙ driver information display (did)” in “understanding your instrument panel” for further information. Tighten the fuel filler cap until a “clicking” sound is heard. This is an indication that the fuel filler cap is properly tightened. Refer to “onboard diagnostic system” in “ma...

  • Page 573

    Each axle gawr is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles or suspension components sometimes specified by purchasers for in- creased durability does not necessarily increase the vehi- cle’s gvwr. Tire size the ...

  • Page 574

    Front or rear axles has been exceeded but the total load is within the specified gvwr. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally....

  • Page 575

    Exceed the gvwr. Refer to “vehicle loading/vehicle certification label” in “starting and operating” for further information. Gross trailer weight (gtw) the gtw is the weight of the trailer plus the weight of all cargo, consumables, and equipment (permanent or tem- porary) loaded in or on the trailer...

  • Page 576

    Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision. Tongue weight (tw) the tongue weight is the downward force exerted on the hitch ball by t...

  • Page 577

    Tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s directions, it pro- vides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety. The addition of a friction/hydraulic sway control also dampens sway ...

  • Page 578

    Trailer hitch classification definitions class max. Trailer hitch industry standards class i - light duty 2,000 lbs (907 kg) class ii - medium duty 3,500 lbs (1 587 kg) class iii - heavy duty 5,000 lbs (2 268 kg) class iv - extra heavy duty 10,000 lbs (4 540 kg) refer to the “trailer towing weights ...

  • Page 579

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission model frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.4l/automatic with or without trailer tow ...

  • Page 580

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo (ie. The gvwr), and the gvwr should never exceed the weight referenced on the tire and loading information placard. Refer to “tire safety information” in “starting and operating” for further info...

  • Page 581

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “tire and loading information” placard for the maximum combine...

  • Page 582

    Warning! (continued) • vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle transmission in park. Always, block or ⴖ chock ⴖ the trailer wheels. • gcwr must not be exceeded. • total weight must be distributed between th...

  • Page 583

    • check the trailer tires for proper tire inflation pres- sures before trailer usage. • check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information” in “starting and operating” for the proper inspection procedure. • when replacing tires, refer t...

  • Page 584

    Warning! (continued) • towing any trailer will increase your stopping distance. When towing you should allow for addi- tional space between your vehicle and the vehicle in front of you. Failure to do so could result in a collision. Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, ...

  • Page 585

    Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground 2 — backup lamps 6 — left stop/turn 3 — right stop/turn 7 — running lamps 4 — electric brakes 5 starting and operating 583.

  • Page 586

    Towing tips before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Automatic transmission — if equipped the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting wh...

  • Page 587

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle 4x4 models towing condition wheels off the ground front-wheel drive (fwd) models 1-speed power transfer unit 2-speed power transfer unit flat tow none not allowed not allowed see instructions: • transmission in p...

  • Page 588

    Recreational towing — front-wheel drive (fwd) models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for front-wheel drive models) is allowed only if the front wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using ...

  • Page 589

    Caution! Towing this vehicle with any of its wheels on the ground can cause severe transmission and/or power transfer unit damage. Damage from improper towing is not covered under the new vehicle limited war- ranty. Recreational towing — 4x4 models with 2-speed power transfer unit the power transfer...

  • Page 590

    Caution! (continued) • towing this vehicle in violation of the above re- quirements can cause severe transmission and/or power transfer unit damage. Damage from im- proper towing is not covered under the new ve- hicle limited warranty. • do not use a bumper-mounted clamp-on tow bar on your vehicle. ...

  • Page 591

    1. Bring the vehicle to a complete stop and shift the transmission to park. 2. Turn the engine off. 3. Turn the ignition switch to the on/run position, but do not start the engine. 4. Press and hold the brake pedal. 5. Shift the transmission into neutral. 6. Using a ballpoint pen or similar object, ...

  • Page 592

    10. Release the brake pedal for five seconds and ensure that there is no vehicle movement. 11. Shift the transmission to neutral. 12. Apply the parking brake. 13. Shift the transmission into park, turn the engine off, and remove the key fob. 14. Attach the vehicle to the tow vehicle using a suitable...

  • Page 593

    Shifting out of neutral (n) use the following procedure to prepare your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Apply the parking brake. 3. Turn the ignition switch to the on/run position, but do not start the engine. 4. Press ...

  • Page 594

    Note: when shifting the power transfer unit out of neutral (n), the engine should remain off to avoid gear clash. 9. Shift the transmission into park. 10. Release the brake pedal. 11. Disconnect vehicle from the tow vehicle. 12. Start the engine. 13. Press and hold the brake pedal. 14. Release the p...

  • Page 595: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .595 䡵 if your engine overheats . . . . . . . . . . . .595 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .596 ▫ torque specifications . . . . . . . . . . . . . . . . . .597 䡵 tire serv...

  • Page 596

    䡵 shift lever override . . . . . . . . . . . . . . . .628 䡵 towing a disabled vehicle . . . . . . . . . . .628 ▫ front-wheel drive (fwd) models . . . . . . . . .630 ▫ 4x4 models with 1–speed power transfer unit — with key fob . . . . . . . . . . . . . . . . . . . . . . . .631 ▫ 4x4 models with 2–spe...

  • Page 597

    Hazard warning flashers the hazard warning flasher switch is located in the switch bank below the radio screen. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the...

  • Page 598

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maximum he...

  • Page 599

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/ bolt socket size 100 ft-lbs (135 n·m) m12 x 1.25 19 mm **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the ...

  • Page 600

    After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may ...

  • Page 601

    Tire service kit storage the tire service kit is stowed under the load floor behind the rear seat. 1. Open the liftgate. 2. Lift the access cover using the load floor handle. Load floor handle 6 what to do in emergencies 599.

  • Page 602

    Tire service kit components and operation using the mode select knob and hoses your tire service kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black ai...

  • Page 603

    Using the power button push and release the power button (4) once to turn on the tire service kit. Push and release the power button (4) again to turn off the tire service kit. Using the deflation button push the deflation button (2) to reduce the air pressure in the tire if it becomes over-inflated...

  • Page 604

    From the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • for optimum performance, make sure the valve stem on the wheel is free of debris before connecting the tire service kit. • you can use the tire service kit air pump to inflate...

  • Page 605

    Warning! (continued) • keep tire service kit away from open flames or heat source. • a loose tire service kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tire service kit in the place provided. Failure to follow these warn- ings can result ...

  • Page 606

    On the ground. This will provide the best positioning of the kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceeding. 3. Place the transmission in park (auto transmission) or in gear (man...

  • Page 607

    Note: sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow within 0 – 10 seconds through the sealant hose (6): 1. Push the power button (4) to turn off the tire service kit. Disconnect the sealant hose (6) from the valve stem. Make sure the valve stem is ...

  • Page 608

    Latch pillar (recommended pressure). Check the tire pressure by looking at the pressure gauge (3). If the tire does not inflate to at least 26 psi (1.8 bar) pressure within 15 minutes: • the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. Note: if the tir...

  • Page 609

    (d) drive vehicle: immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure distribution of the tire service kit sealant within the tire. Do not exceed 55 mph (90 km/h). Warning! Tire service kit is not a permanent flat tire repair. Have th...

  • Page 610

    Note: if the tire becomes over-inflated, push the defla- tion button to reduce the tire pressure to the recom- mended inflation pressure before continuing. 2. Disconnect the tire service kit from the valve stem, reinstall the cap on the valve stem and unplug from 12 volt outlet. 3. Place the tire se...

  • Page 611

    The front of the housing. Push the bottle into the housing. An audible click will be heard indicating the bottle is locked into place. 6. Verify that the cap is installed on the fitting at the end of the sealant hose (6) and return the hose to its storage area (located on the bottom of the air pump)...

  • Page 612

    1. Open the liftgate. 2. Lift the access cover using the load floor handle. 3. Remove the hook from the stowed position on the back side of the load floor and place the hook over the top body in white flange and weather seal. This will hold the load floor up while obtaining the jack and spare tire. ...

  • Page 613

    6. Remove the scissors jack and wheel bolt wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the wheel bolt wrench, and remove the wrench from the jack assembly. Note: the jack handle attaches to the side of the jack with two attachment points. When the jack is pa...

  • Page 614

    Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Turn on the hazard warning flasher. 3. Set the parking brake. 4. Place the shift lever into park (automatic t...

  • Page 615

    Warning! (continued) • never start or run the engine with the vehicle on a jack. • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. ...

  • Page 616

    3. Before raising the vehicle, use the wheel bolt wrench to loosen, but not remove, the wheel bolts on the wheel with the flat tire. Turn the wheel bolts counter- clockwise one turn while the wheel is still on the ground. 4. Place the jack underneath the lift area that is closest to the flat tire. T...

  • Page 617

    Rear jacking location rear jacking engagement point 6 what to do in emergencies 615.

  • Page 618

    5. Raise the vehicle just enough to remove the flat tire. Front jacking location front jacking engagement point 616 what to do in emergencies.

  • Page 619

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire. 7. Remove the alignment pin from the jack assembly and thread the pin into t...

  • Page 620

    Note: • for vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. • refer to “compact spare tire” and to “limited-use spare” under “tires—general information” in “starting and operating” for additional warnings, cautions, and information about the spare ti...

  • Page 621

    12. Securely stow the jack, tools, chocks and flat tire. Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in (continued) assembled jack stowed tire, jack and chock 6 what to do in eme...

  • Page 622

    Warning! (continued) the places provided. Have the deflated (flat) tire repaired or replaced immediately. Road tire installation 1. Mount the road tire on the axle. 2. Install the remaining wheel bolts with the threaded end of the wheel bolt toward the wheel. Lightly tighten the wheel bolts. Warning...

  • Page 623

    Jump-starting procedures if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section caref...

  • Page 624

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 625

    2. Turn off the heater, radio, and all unnecessary electri- cal accessories. 3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not allow vehicles to touch each other as this cou...

  • Page 626

    Warning! Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electri- cal spark could cause the battery to explode and could result in serious injury. Only use the specific ground point, do not use any other exposed metal parts. 5. Start the engine in th...

  • Page 627

    Caution! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough without engine operation, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prev...

  • Page 628

    Caution! (continued) • when “rocking” a stuck vehicle by shifting be- tween drive and reverse, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also dama...

  • Page 629

    Warning! Recovery straps should only be used in emergencies to rescue stranded vehicles. Only use recovery straps on vehicles that fit within the recommended gvw of your recovery strap. Only attach recovery straps to oe recommended anchor points or emergency towing an- chor points. Never attach to t...

  • Page 630

    Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use the following procedure to temporarily move the shift lever: 1. Turn the engine off. 2. Apply the parking brake. 3. Using a screwdriver or similar tool, carefully separate the shift...

  • Page 631

    4x4 models towing condition wheels off the ground fwd models 1–speed power transfer unit 2–speed power transfer unit flat tow none not allowed not allowed see instructions under “recreational towing” in “starting and operating” • transmission in park • power transfer unit in neutral • tow in forward...

  • Page 632

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 633

    If flatbed equipment is not available, this vehicle must towed with the front wheels off the ground (using a towing dolly, or wheel lift equipment with the front wheels raised). Caution! Towing this vehicle in violation of the above require- ments can cause severe transmission damage. Dam- age from ...

  • Page 634

    4x4 models with 2–speed power transfer unit — with key fob the manufacturer recommends towing with all four wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly. If flatbed equipment is not availabl...

  • Page 635: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 2.4l . . . . . . . . . .635 䡵 engine compartment — 3.2l . . . . . . . . . .636 䡵 onboard diagnostic system — obd ii . .637 ▫ loose fuel filler cap message . . . . . . . . . . . .637 䡵 emissions inspection and maintenance programs . . . . . . ....

  • Page 636

    ▫ cooling system . . . . . . . . . . . . . . . . . . . . . .665 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . .671 ▫ automatic transmission . . . . . . . . . . . . . . . .673 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .675 䡵 fus...

  • Page 637

    Engine compartment — 2.4l 1 — air cleaner filter 5 — power distribution center (fuses) 2 — engine coolant pressure cap 6 — battery 3 — oil fill cap 7 — washer fluid reservoir 4 — brake fluid reservoir 8 — engine oil dipstick 7 maintaining your vehicle 635.

  • Page 638

    Engine compartment — 3.2l 1 — engine coolant reservoir 5 — washer fluid reservoir 2 — engine oil filter access cover 6 — engine oil dipstick 3 — brake fluid reservoir 7 — engine oil fill 4 — power distribution center (fuses) 8 — air cleaner filter 636 maintaining your vehicle.

  • Page 639

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 640

    Further information. Tighten the fuel filler cap until a “clicking” sound is heard. This is an indication that the fuel filler cap is properly tightened. Refer to “onboard diagnostic system” in “maintaining your vehicle” for further information. Emissions inspection and maintenance programs in some ...

  • Page 641

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 642

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 643

    Caution! • failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle perfor- mance. Immediately have potential malfunctions examined by an authorized dealer or qualified repai...

  • Page 644

    Caution! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” for ...

  • Page 645

    Engine oil viscosity (sae grade) — 2.4l engine mopar® sae 0w-20 engine oil or equivalent pennzoil® or shell helix® is recommended for all operating tem- peratures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also states the recommended engin...

  • Page 646

    Disposing of used engine oil and oil filters care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer, service station or governmental agency ...

  • Page 647

    Warning! (continued) vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury. Engine air cleaner filter selection the quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be us...

  • Page 648

    2. Push in on the quick connect clip with your thumb and remove by pulling hose (if equipped) away from air cleaner filter cover. 3. Lift the air cleaner cover to access the air cleaner filter. Air cleaner air hose — if equipped 1 — air filter cleaner cover 2 — air hose (if equipped) 3 — quick conne...

  • Page 649

    4. Remove the air cleaner filter element from the housing assembly. Engine air cleaner filter installation note: inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air cleaner filter element into the housing assembly with the air cleane...

  • Page 650

    Warning! (continued) • when working near the radiator cooling fan, dis- connect the fan motor lead. The fan is temperature controlled and can start at any time regardless of ignition switch position. You could be injured by the moving fan blades. • you can be badly injured working on or around a mot...

  • Page 651

    • rib or belt wear • longitudinal belt cracking (cracks between two ribs) • belt slips • “groove jumping ⬙ (belt does not maintain correct position on pulley) • belt broken (note: identify and correct problem before new belt is installed) • noise (objectionable squeal, squeak, or rumble is heard or ...

  • Page 652

    Warning! (continued) an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after handling. Caution! • it is essential when replacing the cables on the battery that the positive c...

  • Page 653

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 654

    Refrigerant recovery and recycling hfo 1234yf — if equipped hfo 1234yf air conditioning refrigerant is a hydro- fluorocarbon (hfc) that is endorsed by the environmen- tal protection agency and is an ozone-saving product with a low gwp (global warming potential). However, the manufacturer recommends ...

  • Page 655

    3. Pull down the passenger hush panel under the dash panel 4. Remove the filter door by pushing down the tab on the top of the door to release the cover then rotate the door out and lift up. Console closeout panel hush panel 7 maintaining your vehicle 653.

  • Page 656

    5. Remove the a/c air filter by pulling it straight out of the housing. Take note of the air filter position indica- tors. 6. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. Air filter cover location a/c air filter 654 maintaining your ve...

  • Page 657

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 7. Install the passenger side hush panel under the dash panel and console closeout. Refer to the “mainten...

  • Page 658

    Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact...

  • Page 659

    2. To disengage the wiper blade from the wiper arm, flip up the release tab on the wiper blade and while holding the wiper arm with one hand, slide the wiper blade down towards the base of the wiper arm. Wiper blade with release tab in locked position 1 — wiper 2 — release tab 3 — wiper arm 7 mainta...

  • Page 660

    3. With the wiper blade disengaged, remove the wiper blade from the wiper arm by holding the wiper arm with one hand and separating the wiper blade from the wiper arm with the other hand (move the wiper blade toward the right side of the vehicle to separate the wiper blade from the wiper arm). Wiper...

  • Page 661

    4. Gently lower the wiper arm onto the glass. Installing the front wipers 1. Lift the wiper arm off of the glass, until the wiper arm is in the full up position. 2. Position the wiper blade near the hook on the tip of the wiper arm with the wiper release tab open and the blade side of the wiper faci...

  • Page 662

    Rear wiper blade removal/installation 1. Lift the rear wiper arm pivot cap away from the glass to allow the rear wiper blade to be raised off of the glass. Note: the rear wiper arm cannot be fully raised off the glass unless the wiper arm pivot cap is unsnapped first. Attempting to fully raise the r...

  • Page 663

    3. To remove the wiper blade from the wiper arm, grasp the bottom end of the wiper blade nearest to wiper arm with your right hand. With your left hand hold the wiper arm as you pull the wiper blade away from the wiper arm past its stop far enough to unsnap the wiper blade pivot pin from the recepta...

  • Page 664

    5. Gently lower the tip of the wiper arm onto the glass. Installing the rear wiper 1. Lift the rear wiper arm pivot cap away from the glass to allow the rear wiper blade to be raised off of the glass. Note: the rear wiper arm cannot be fully raised off the glass unless the wiper arm pivot cap is uns...

  • Page 665

    4. Lower the wiper blade onto the glass and snap the wiper arm pivot cap back into place. Adding washer fluid the windshield and rear window washers share the same fluid reservoir. The fluid reservoir is located in the front of the engine compartment. Be sure to check the fluid level in the reservoi...

  • Page 666

    Exhaust system inspected each time the vehicle is raised for lubrication or oil change. Replace as required. Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid ...

  • Page 667

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 668

    Engine coolant checks check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty, the system should be drained, flushed, and refilled with fresh oat coolant (conforming to ms.90032) by an auth...

  • Page 669

    Selection of coolant refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decr...

  • Page 670

    Miles (240,000 km) before replacement. To prevent reduc- ing this extended maintenance period, it is important that you use the same engine coolant (oat coolant conform- ing to ms.90032) throughout the life of your vehicle. Please review these recommendations for using organic additive technology (o...

  • Page 671

    Hoat and oat coolant are mixed in an emergency, have a authorized dealer drain, flush, and refill with oat coolant (conforming to ms.90032) as soon as possible. Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coola...

  • Page 672

    Coolant level the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine off and cold, the level of the engine coolant (antifreeze) in the bottle should be between the ranges indicated on the bottle. The radiator normally remains completely ...

  • Page 673

    • if frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested for leaks. • maintain engine coolant (antifreeze) concentration at a minimum of 50% oat coolant (conforming to ms.90032) and distilled water for proper corrosion protection of your engine w...

  • Page 674

    Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. Brake fluid level should be chec...

  • Page 675

    Warning! (continued) the brake fluid to catch fire. Brake fluid can also damage painted and vinyl surfaces, care should be taken to avoid its contact with these surfaces. • do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or c...

  • Page 676

    Of special dyes for diagnosing fluid leaks. Avoid using transmission sealers as they may adversely affect seals. Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid...

  • Page 677

    Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons a...

  • Page 678

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover to remove. • use a high quality cleaner wax, such as mopar® cleaner wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • av...

  • Page 679

    • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • if a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • use mopar® touch up paint on scratches as soon as possible. You...

  • Page 680

    Stain repel fabric cleaning procedure — if equipped stain repel seats may be cleaned in the following man- ner: • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar® total clean, or a mild ...

  • Page 681

    Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar® total clean o...

  • Page 682

    Cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or windows equipped with radio antennas. Do not use scrapers or other sharp instrument that may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using...

  • Page 683

    Warning! (continued) assemblies must be replaced after a collision if they have been damaged (i.E., bent retractor, torn web- bing, etc.). Fuses warning! • when replacing a blown fuse, always use an appro- priate replacement fuse with the same amp rating as the original fuse. Never replace a fuse wi...

  • Page 684

    Power distribution center the power distribution center is located in the engine compartment near the battery. This center contains car- tridge fuses, mini-fuses and relays. A label that identifies each component is printed on the inside of the cover. Power distribution center 682 maintaining your v...

  • Page 685

    Cavity blade fuse cartridge fuse description f06 – – not used f07 15 amp blue – powertrain control module - pcm (diesel only) f08 25 amp clear – engine control module (ecm)/fuel injection f09 – – not used f10 20 amp yellow – power transfer unit (ptu) – if equipped f11 – – not used f12 20 amp yellow ...

  • Page 686

    Cavity blade fuse cartridge fuse description f19 – 40 amp green starter solenoid f20 10 amp red – a/c compressor clutch f21 – – not used f22 5 amp tan – radiator fan f23 70 amp tan – body controller module (bcm) - feed 2 f23 50 amp red – voltage stability module (vsm) feed #2 - if equipped with stop...

  • Page 687

    Cavity blade fuse cartridge fuse description f32 – – not used f33 – – not used f34 – – not used f35 – – not used f36 – – not used f37 – – not used f38 – – not used f38 – 60 amp yellow glow plugs (diesel only) - if equipped f39 – 40 amp green hvac blower motor f40 – 20 amp blue trailer tow park light...

  • Page 688

    Cavity blade fuse cartridge fuse description f43 20 amp yellow – fuel pump motor f44 – 30 amp pink trailer tow / 7-way connector - if equipped f45 – 30 amp pink passenger door module (pdm) - if equipped f46 – 25 amp clear sunroof – if equipped f48 – 30 amp pink driver door module - if equipped f49 –...

  • Page 689

    Cavity blade fuse cartridge fuse description f57 20 amp yellow – trailer tow lights left - if equipped f58 10 amp red – occupant classification module/vsm/esc f59 – 30 amp pink drivetrain control module (dtcm) if equipped f60 20 amp yellow – power outlet - center console f61 20 amp yellow – trailer ...

  • Page 690

    Cavity blade fuse cartridge fuse description f68 – – not used f69 10 amp red – power transfer unit switch (tsbm) / active grill shutter (ags) - if equipped with gas engine 69a 10 amp red – power transfer unit switch (tsbm) - if equipped with diesel engine f70 5 amp tan – intelligent battery sensor i...

  • Page 691

    Cavity blade fuse cartridge fuse description f78 10 amp red – diagnostic port f79 10 amp red – integrated center stack (ics) / hvac / aux switch bank module (asbm) / instrument panel cluster (ipc) f80 20 amp yellow – radio / cd - if equipped f81 – – not used f82 – – not used f83 – 20 amp blue engine...

  • Page 692

    Cavity blade fuse cartridge fuse description f90 – – not used f91 20 amp yellow – power outlet rear - if equipped - customer selectable f92 – – not used f93 – 40 amp green brake system module (bsm) - pump motor f94 – 30 amp pink electric park brake (epb) - right f95 10 amp red – electrochromatic mir...

  • Page 693

    Interior fuses the interior fuse panel is located in the passenger com- partment on the left side dash panel under the instru- ment panel. Cavity blade fuse description f13 15 amp blue low beam left f32 10 amp red interior lighting f36 10 amp red intrusion module/siren – if equipped f38 20 amp yello...

  • Page 694

    Cavity blade fuse description f89 10 amp red door locks – driver unlock f91 7.5 amp brown fog lamp front left f92 7.5 amp brown fog lamp front right f93 10 amp red low beam right vehicle storage if you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your ...

  • Page 695

    Replacement bulbs interior bulbs bulb number cargo lamp tl212–2 overhead console lamp plw214–2a reading lamp wl212–2 exterior bulbs bulb number low beam/high beam (bi-halogen) headlamps hir2ll low beam/high beam (bi-xenon) headlamps d3s (serviced at an authorized dealer) front park/daytime running l...

  • Page 696

    Bulb number rear tail/turn/stop lamps led ( serviced at an authorized dealer) center high mounted stop lamp (chmsl) led (serviced at an authorized dealer) back-up lamps w16w or 921 license plate lamp w5w bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will ...

  • Page 697

    Warning! A transient high voltage occurs at the bulb sockets of hid headlamps when the headlamp switch is turned on. It may cause serious electrical shock or electro- cution if not serviced properly. See your authorized dealer for service. Bi-halogen headlamps 1. Remove the 3 hex head screws from th...

  • Page 698

    Front turn signals and front side marker lamps 1. Open the hood. Note: removal of the air cleaner filter housing may be necessary prior to replacing bulbs in the upper lamp assembly on the passenger side of the vehicle. 2. Twist the appropriate bulb and socket assembly coun- terclockwise, and then r...

  • Page 699

    6. Install the 3 hex head screws into the wheel liner. Front fog lamp (trailhawk) 1. Unlock lower access door in wheel liner. 2. Reach behind the fog lamp housing to access the bulb. 3. Squeeze the two tabs on the side of the bulb socket and pull straight out from the fog lamp. 4. Disconnect the wir...

  • Page 700

    8. Reconnect the electrical connector. 9. Reinstall the tail lamp housing and screws. 10. Close the liftgate. Liftgate mounted back-up lamp 1. Open the liftgate. 2. Use a fiber stick or flat blade screw driver to pry the lower trim from the liftgate. 3. Once the trim is loose, pull it back exposing ...

  • Page 701

    Fluid capacities u.S. Metric fuel (approximate) 2.4l and 3.2l engines 15.8 gallons 60 liters engine oil with filter 2.4 liter engine (sae 0w-20, api certified) 5.5 quarts 5.2 liters 3.2 liter engine (sae 5w-20, api certified) 6 quarts 5.6 liters cooling system* 2.4 liter engine (mopar® antifreeze/en...

  • Page 702

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of fca material standard ms.90032. Engine oil – ...

  • Page 703

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 704

    Chassis component fluid, lubricant, or genuine part automatic transmission use only mopar® zf 8&9 speed atf™ automatic transmission fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Brake master cylinder we recommend you use mopar® do...

  • Page 705: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .704 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .706 8.

  • Page 706

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 707

    • check tire pressure and look for unusual wear or damage. Rotate tires at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. • check the fluid levels of the coolant reservoir and brake master cylinder, fill as needed. • check function of all interior and e...

  • Page 708

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176...

  • Page 709

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 710

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 711: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .711 ▫ prepare for the appointment . . . . . . . . . . . . .711 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .711 ▫ be reasonable with requests ...

  • Page 712

    䡵 publication order forms . . . . . . . . . . . .715 䡵 department of transportation uniform tire quality grades . . . . . . . .717 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .717 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .717 ▫ temperature grades. . . . . . . ...

  • Page 713

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 714

    This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer. They want to know if you need assistance. • if an autho...

  • Page 715

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 716

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You will be pleased with their sincere efforts to re...

  • Page 717

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 718

    Complete working knowledge of the vehicle, system, and/or components is written in straightforward lan- guage with illustrations, diagrams, and charts. Diagnostic procedure manuals diagnostic procedure manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make ...

  • Page 719

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 720

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 721: Index

    Index 10

  • Page 722

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . .497 abs (anti-lock brake system) . . . . . . . . . . . . . . . .498 adaptive cruise control (acc) (cruise control) . . .182 adding engine coolant (antifreeze) . . . . . . . . . . . .667 additives, fuel . . . . . . . . . . . . . . . . ....

  • Page 723

    Alarm arm the system . . . . . . . . . . . . . . . . . . . . . . . .19 alarm, panic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 alarm (security alarm) . . . . . . . . . . . . . . . . . .19, 319 alarm system (security alarm) . . . . . . . . . . . . . . . .19 all wheel drive (awd). . ....

  • Page 724

    Blind spot monitoring . . . . . . . . . . . . . . . . . . . . . .134 body mechanism lubrication . . . . . . . . . . . . . . . . .655 b-pillar location . . . . . . . . . . . . . . . . . . . . . . . . . .526 brake assist system . . . . . . . . . . . . . . . . . . . . . . .501 brake control system, ele...

  • Page 725

    Child restraints booster seats . . . . . . . . . . . . . . . . . . . . . . . . . . .94 child restraints . . . . . . . . . . . . . . . . . . . . . . . . .89 child seat installation . . . . . . . . . . . . . . . . . . . .108 how to stow an unused alr seat belt . . . . . . .104 infants and child restra...

  • Page 726

    Selection of coolant (antifreeze) . . . . . .667, 699, 700 corrosion protection . . . . . . . . . . . . . . . . . . . . . . .675 cruise control (speed control). . . . . . . . . . . . . . . .182 cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . .301 customer assistance . . . . . . . ...

  • Page 727

    Electric parking brake . . . . . . . . . . . . . . . . . . . . . .490 electric remote mirrors . . . . . . . . . . . . . . . . . . . . .131 electronic brake control system . . . . . . . . . . . . . . .498 electronic range select (ers) . . . . . . . . . . . . . . . . .471 electronic roll mitigation (e...

  • Page 728

    Engine oil viscosity chart . . . . . . . . . . . . . . . . . . .643 enhanced accident response feature . . . . . . . . . . . .85 entry system, illuminated . . . . . . . . . . . . . . . . . . . .22 ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .559 event data recorder . . . . ...

  • Page 729

    Folding rear seat . . . . . . . . . . . . . . . . . . . . . . . . .151 forward collision warning . . . . . . . . . . . . . . . . . .209 four wheel drive . . . . . . . . . . . . . . . . . . . . . . . . .482 freeing a stuck vehicle . . . . . . . . . . . . . . . . . . . . .625 fuel . . . . . . . . . . ...

  • Page 730

    Gvwr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .570 hazard warning flasher . . . . . . . . . . . . . . . . . . . .595 headlights automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .161 bulb replacement . . . . . . . . . . . . . . . . . . . . . . .695 cleaning . . ....

  • Page 731

    Instrument cluster . . . . . . . . . . . . . . . . . . .331, 347 instrument panel and controls . . . . . . . . . . . . . . . .316 instrument panel cover . . . . . . . . . . . . . . . . . . . . .678 instrument panel lens cleaning . . . . . . . . . . . . . . .680 interior appearance care . . . . . . ....

  • Page 732

    Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 lead free gasoline . . . . . . . . . . . . . . . . . . . . . . . .558 leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .541 liftgate ...

  • Page 733

    Rear servicing . . . . . . . . . . . . . . . . . . . . . .697, 698 rear tail lamps . . . . . . . . . . . . . . . . . . . . .697, 698 seat belt reminder . . . . . . . . . . . . . . . . . . . . . .319 security alarm . . . . . . . . . . . . . . . . . . . . . . . . .319 service . . . . . . . . . . . . ....

  • Page 734

    Electric remote . . . . . . . . . . . . . . . . . . . . . . . . .131 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 vanity . . . . . ....

  • Page 735

    Owner’s manual (operator manual) . . . . . . . . . .5, 715 paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .675 panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 parking brake. . . . . . . . . . . . . . . . . . . . . . . . . . . .490 parksense® system, re...

  • Page 736

    Recorder, event data . . . . . . . . . . . . . . . . . . . . . . .88 recreational towing . . . . . . . . . . . . . . . . . . . . . . .585 shifting into power transfer unit neutral (n) . . .588 shifting into transfer case neutral (n) . . . . . . . .588 shifting out of power transfer unit neutral (n) ...

  • Page 737

    Safety checks inside vehicle. . . . . . . . . . . . . . . . . .114 safety checks outside vehicle . . . . . . . . . . . . . . . .116 safety defects, reporting . . . . . . . . . . . . . . . . . . . .714 safety, exhaust gas . . . . . . . . . . . . . . . . . . . . . . . .113 safety information, tire . ....

  • Page 738

    Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 rear folding . . . . . . . . . . . . . . . . . . . . . . . . . .151 seatback release . . . . . . . . . . . . . . . . . . . .145, 151 tilting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 security alarm. . . . . ...

  • Page 739

    Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29, 452 cold weather . . . . . . . . . . . . . . . . . . . . . . . . . .453 engine fails to start . . . . . . . . . . . . . . . . . . . . .454 remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 starting and opera...

  • Page 740

    Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .609 compact spare . . . . . . . . . . . . . . . . . . . . . . . . .538 general information . . . . . . . . . . . . . . . . . . . . .531 high speed . . . . . . . . . . . . . . . . . . . . . . . . . . .534 inflation pressures . . . . . ...

  • Page 741

    Trailer towing guide. . . . . . . . . . . . . . . . . . . . . . .577 trailer weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .577 transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .461 automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .461 operation . ....

  • Page 742

    Vehicle identification number (vin) . . . . . . . . . . . . .7 vehicle loading . . . . . . . . . . . . . . . . . . . . . . .528, 570 vehicle modifications/alterations . . . . . . . . . . . . . . .8 vehicle security alarm (security alarm) . . . . . . . . . .19 vehicle storage. . . . . . . . . . . . ....

  • Page 743

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 744

    Cherokee o w n e r ’ s m a n u a l 20 15 cher ok ee 15kl74-126-ad fourth edition rev 1 printed in u.S.A. 2 0 1 5 fca us llc.