1. DL manuals
  2. Jeep
  3. Automobile
  4. 2015 Cherokee
  5. Owner's Manual

Jeep 2015 Cherokee Owner's Manual

Summary of 2015 Cherokee

  • Page 1

    Grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2015 gr and cher ok ee 15wk741-126-aa first edition printed in u.S.A. 2 0 1 5.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents ! Introduction . . . . . . . . . . . . . . . . . . . . . . . .4 ! Rollover warning . . . . . . . . . . . . . . . . . . .5 ! How to use this manual . . . . . . . . . . . . . .6 ! Warnings and cautions . . . . . . . . . . . . . .8 ! Vehicle identification number . . . . . . . .8 ...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle. It can go places and perform tasks t...

  • Page 7

    This owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by warranty information, and various customer-oriented documents. Please take the time to read these publications ...

  • Page 8

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million a...

  • Page 9

    1 introduction 7.

  • Page 10

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 11

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 1 introduct...

  • Page 13: Contents

    Things to know before starting your vehicle contents ! A word about your keys . . . . . . . . . . . . .13 ▫ keyless ignition node (kin) . . . . . . . . . . . . . .13 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ ignition or accessory on message . . . . . . . . . .15 ! Sentr...

  • Page 14

    ▫ general information . . . . . . . . . . . . . . . . . . . .27 ! Remote starting system — if equipped . .27 ▫ how to use remote start . . . . . . . . . . . . . . . .28 ! Door locks . . . . . . . . . . . . . . . . . . . . . . . . .31 ▫ power door locks . . . . . . . . . . . . . . . . . . . . .32 ▫ c...

  • Page 15

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a keyless ignition node (kin). Keyless enter-n-go™ feature this vehicle is equipped with the keyless enter-n-go™ feature, (refer to # keyless enter-n-...

  • Page 16

    Key fob the key fob also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the key fob go dead. The emergency key is also for locking the glove bo...

  • Page 17

    Ignition or accessory on message opening the driver’s door when the ignition is in acc or on (engine not running), a chime will sound to remind you to cycle the ignition to off. In addition to the chime, the ignition or accessory on message will display in the cluster. Note: with the uconnect® syste...

  • Page 18

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove the key fob from vehicle, cycle the ignition off and lock all doors when leavin...

  • Page 19

    Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. Caution! • do not make modifications or alterations to the immobilizer system. Modifications or alterations to the immobilization system may result in a loss of security protection. • the sentry key® immobilize...

  • Page 20

    At the time of purchase, the original owner is provided with a four-digit personal identification number (pin). Keep the pin in a secure location. This number is required for authorized dealer replacement of key fobs. Duplication of key fobs may be performed at an autho- rized dealer. This procedure...

  • Page 21

    Vehicle security alarm — if equipped this vehicle security alarm monitors the vehicle doors, liftgate, and ignition for unauthorized operation. When the alarm is activated, the interior switches for door locks, and power liftgate are disabled. The vehicle secu- rity alarm provides both audio and vis...

  • Page 22

    2. Perform one of the following methods to lock the vehicle: • push lock on the interior power door lock switch with the driver and/or passenger door open. • push the lock button on the exterior passive entry door handle with a valid key fob available in the same exterior zone (refer to # keyless en...

  • Page 23

    • when the vehicle security alarm is armed, the interior power door lock switches will not unlock the doors. The vehicle security alarm is designed to protect your vehicle; however, you can create conditions where the system will give you a false alarm. If one of the previ- ously described arming se...

  • Page 24

    Note: • the front courtesy overhead console and door cour- tesy lights will turn on if the dimmer control is in the “dome on” position (extreme top position). • the illuminated entry system will not operate if the dimmer control is in the “dome defeat” position (extreme bottom position). Remote keyl...

  • Page 25

    To unlock the doors and liftgate push and release the unlock button on the rke transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn o...

  • Page 26

    Remote starting system — if equipped this feature allows the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security. The system has a range of approximately 300 ft (91 m). Note: • the vehicle must be equipped with an automa...

  • Page 27

    The panic alarm will stay on for three minutes unless you turn it off by either pushing the panic button a second time or drive the vehicle at a speed of 15 mph (24 km/h) or greater. Note: • the interior lights will turn off if you cycle the ignition switch to the acc or on/run position while the pa...

  • Page 28

    1. Remove the emergency key by sliding the mechanical latch on the back of the rke transmitter sideways with your thumb and then pull the key out with your other hand. 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the rke transmi...

  • Page 29

    New battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4. To assemble the rke transmitter case, snap the two halves together. General information this device complies with part 15 of the fcc rules and rss 210 of industry canad...

  • Page 30

    Note: • the vehicle must be equipped with an automatic transmission to be equipped with remote start. • obstructions between the vehicle and the rke trans- mitter may reduce this range. How to use remote start all of the following conditions must be met before the engine will remote start: • shift l...

  • Page 31

    Remote start abort message on driver information display (did) — if equipped the following messages will display in the did if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start aborted — fuel lo...

  • Page 32

    • for security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the remote start mode. • the engine can be started two consecutive times (two 15-minute cycles) with the rke transmitter. However, the ignition switch must be cycled to the on/run position be...

  • Page 33

    When the remote start is activated. These features will stay on through the duration of remote start or until the ignition switch is turned to the on/run position. The comfort system can be activated and deactivated through the uconnect® system. For more information on comfort system operation refer...

  • Page 34

    Warning! • for personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • when leaving the vehicle, always remove the key fob from the vehicle and lock your vehicle. Unsu- pervised use of vehicle equipment may c...

  • Page 35

    If the door lock switch is pressed down when the door is closed, the door will lock. Therefore, make sure the key fob is not inside the vehicle before closing the door. If the door lock switch is pressed while the ignition is in acc or on/run and the driver’s door is open, the doors will not lock. I...

  • Page 36

    Child-protection door lock system — rear doors to provide a safer environment for small children riding in the rear seats, the rear doors are equipped with child-protection door lock system. To engage or disengage the child-protection door lock system 1. Open the rear door. 2. Insert the tip of the ...

  • Page 37

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged (locked). Note: for emergency exit from the rear seats when the child-protection door lock system is engaged, manually raise the do...

  • Page 38

    • if the vehicle is unlocked by passive entry and no door goes ajar within 60 seconds, the vehicle will re-lock and if equipped will arm the security alarm. • if wearing gloves on your hands, or if it has been raining on the passive entry door handle, the unlock sensitivity can be affected, resultin...

  • Page 39

    To unlock from the passenger side: with a valid passive entry rke transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors automati- cally. The interior door panel lock knob will raise when the door is unlocked. Note: all doors will ...

  • Page 40

    To unlock/enter the liftgate the liftgate passive entry unlock feature is built into the electronic liftgate release. With a valid passive entry rke transmitter within 3 ft (1.0 m) of the liftgate, press the electronic liftgate release for a power open on vehicles equipped with power liftgate. Press...

  • Page 41

    To lock the liftgate with a valid passive entry rke transmitter within 3 ft (1.0 m) of the liftgate, press the passive entry lock button located to the right of electronic liftgate release. Note: if “unlock all doors 1st press” is programmed in uconnect® settings, all doors will unlock when you push...

  • Page 42

    Do not grab the door handle, when pushing the door handle button. This could unlock the door(s). Note: • after pushing the door handle button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle ...

  • Page 43

    Windows power windows the power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door and rear doors which operate the front passenger and rear passenger door windows. The win- dow controls will operate only when the ignition switch is in t...

  • Page 44

    Warning! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n- go™ in the acc or on/run mode. O...

  • Page 45

    Auto up feature with anti-pinch protection — driver and front passenger door only lift the window switch fully upward to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the auto up operation, push down on the switch briefly. To...

  • Page 46

    Note: if the window runs into any obstacle during auto up it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window. Any impact due to rough road condi- tions may trigger the auto reverse function unexpectedly during auto up. If this hap...

  • Page 47

    Window lockout button the window lockout button on the driver’s door allows you to disable the window controls on the rear doors. To disable the window controls on the rear doors, push the window lockout button. To enable the window controls, push the window lockout button again. Wind buffeting wind...

  • Page 48

    Note: if “unlock all doors 1st press” is programmed in uconnect® settings, all doors will unlock when you push the electronic liftgate release. If # unlock driver door 1st press # is programmed in uconnect® settings, the liftgate will unlock when you press the electronic liftgate release. For furthe...

  • Page 49

    Warning! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Power liftgate — if equipped the power liftgate may be opened by pressing the electroni...

  • Page 50

    Note: • in the event of a power malfunction to the liftgate, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the lift- gate trim panel. • if liftgate is left open for an extended period of t...

  • Page 51

    • the power liftgate must be in the full open position for rear liftgate close button on the left rear trim, near the liftgate opening, to operate. If the liftgate is not fully open, press the liftgate button on the key fob twice to fully open the liftgate, and then press it twice to close. • if the...

  • Page 52

    Occupant restraint systems some of the most important safety features in your vehicle are the restraint systems: • seat belt systems • supplemental restraint systems (srs) air bags • supplemental active head restraints • child restraints important safety precautions please pay close attention to the...

  • Page 53

    5. You should read the instructions provided with your child restraint to make sure that you are using it properly. 6. All occupants should always wear their lap and shoulder belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the advanced front ...

  • Page 54

    Ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Enhanced seat belt use reminder system (beltalert®) beltalert® is a feature intended to remind the driver and outboard front passenger (if equipped with outboard f...

  • Page 55

    Note: if beltalert® has been deactivated, the seat belt reminder light will continue to illuminate while the driver’s or outboard front passenger’s (if equipped with beltalert®) seat belt remains unbuckled. Lap/shoulder belts all seating positions in your vehicle are equipped with lap/shoulder belts...

  • Page 56

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. • wearing your seat belt incorrectly could make your injuries in a collision much worse. You ...

  • Page 57

    Warning! (continued) • a seat belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • a seat belt that is worn under your arm is danger- ous. Your body could strike the inside surfaces...

  • Page 58

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the sea...

  • Page 59

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 60

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automaticall...

  • Page 61

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 62

    Warning! • only use a seat belt extender if it is physically required in order to properly fit the original seat belt system. Do not use the seat belt extender if, when worn, the distance between the front edge of the seat belt extender buckle and the center of the occupant’s body is less than 6 inc...

  • Page 63

    The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately. Energy management feature this vehicle has a seat belt system with an energy manageme...

  • Page 64

    If the passenger seating position is equipped with an alr and is being used for normal usage: only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt r...

  • Page 65

    3. Allow the seat belt to retract. As the seat belt retracts, you will hear a clicking sound. This indicates the seat belt is now in the automatic locking mode. How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the ...

  • Page 66

    How the active head restraints (ahr) work the occupant restraint controller (orc) determines whether the severity, or type of rear impact will require the active head restraints (ahr) to deploy. If a rear impact requires deployment, both the driver and front passenger seat ahrs will be deployed. Whe...

  • Page 67

    Warning! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: for more information on properly adjusting and positi...

  • Page 68

    3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. A — downward movement b — rearward movement c — final downward movement to engage locking mechanism review table below 66 things to know before starting your vehicle.

  • Page 69

    4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an autho...

  • Page 70

    • supplemental side air bags • supplemental knee air bags • front and side impact sensors • seat belt pretenioners • seat belt buckle switch • seat track position sensors advanced front air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the s...

  • Page 71

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 72

    Warning! • no objects should be placed over or near the air bag on the instrument panel or steering wheel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bags to inflate. • do not put anything on or around the air bag covers or attempt to op...

  • Page 73

    On the other hand, depending on the type and location of impact, advanced front air bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves a...

  • Page 74

    Supplemental driver knee air bag this vehicle is equipped with a supplemental driver knee air bag mounted in the instrument panel below the steering column. The supplemental driver knee air bag provides enhanced protection during a frontal impact by working together with the seat belts, pretensioner...

  • Page 75

    The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure you if you are not seated properly, or if items are positioned in the area where the sab inflates. Children are at an e...

  • Page 76

    Sabics may help reduce the risk of head injury to front and rear seat outboard occupants. Sabics may reduce the risk of injuries in certain side impact and vehicle rollover events, in addition to the injury reduction poten- tial provided by the seat belts and body structure. The sabics deploy downwa...

  • Page 77

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts and certain rollover events. The occupant restraint controller (“orc”) de- termines whether the deployment of the side air bags in a particular side impact or rollover event is appropriate, based on the severity a...

  • Page 78

    Warning! (continued) • relying on the side air bags alone could lead to more severe injuries in a collision. The side air bags work with your seat belt to restrain you properly. In some collisions, side air bags won’t deploy at all. Always wear your seat belt even though you have side air bags. Note...

  • Page 79

    Event may be in progress and whether deployment is appropriate. A slower-developing event may deploy the seat belt pretensioners on both sides of the vehicle. A faster-developing event may deploy the seat belt preten- sioners as well as the sabs and sabics on both sides of the vehicle. The rollover ...

  • Page 80

    Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and th...

  • Page 81

    System reset procedure in order to reset the enhanced accident response system functions after an event, the ignition switch must be changed from ignition start or on/run to ignition off. Air bag warning light the air bags must be ready to inflate for your protection in a collision. The occupant res...

  • Page 82

    Free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • the air bag warning light does not come on during the four to eight seconds when the ignition switch is first turned to the on/run position. • the air bag warning light remains on after the four...

  • Page 83

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 84

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 85

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Ch...

  • Page 86

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult seat belt. Always check the child seat owner’s manual to make sure you have the correct seat for your child. Carefully read and follow all the instruc- tions and warnings in...

  • Page 87

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 88

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 89

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 90

    Warning! (continued) • when your child restraint is not in use, secure it in the vehicle with the seat belt or latch anchor- ages, or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal ...

  • Page 91

    If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched. A child’s squirming or slouching can move the seat belt out...

  • Page 92

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 93

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 94

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 92 things to know before starting your vehicle.

  • Page 95

    What is the weight limit (child’s weight + weight of the child re- straint) for using the latch an- chorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and ...

  • Page 96

    Can two child restraints be at- tached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchor- ages, use the seat belt to install a child seat in the center position next to a child...

  • Page 97

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel the...

  • Page 98

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing child restraints...

  • Page 99

    Center arm rest tether for rear-facing child restraints secured in the center seat position with the vehicle seat belts, the rear center seat position has an armrest tether that secures the arm rest in the upward position. 1. To access the center seat arm rest tether, first lower the arm rest. The t...

  • Page 100

    3. Raise the armrest and attach the tether hook to the strap located on the front of the arm rest. Always follow the directions of the child restraint manu- facturer when installing your child restraint. Not all child restraint systems will be installed as described here. To install a latch-compatib...

  • Page 101

    Move it to its rear-most position to make room for the child seat. You may also move the front seat forward to allow more room for the child seat. 4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 5. If the child restraint has ...

  • Page 102

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 103

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor • top tether anchorage symbol 2 things to know before starting your vehicle 101.

  • Page 104

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a for- ward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for- ward facing child restr...

  • Page 105

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 106

    8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test...

  • Page 107

    Pulling down the carpet floor panel to access top tether strap anchorage top tether strap anchorage (located on seatback) 2 things to know before starting your vehicle 105.

  • Page 108

    3. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If...

  • Page 109

    Warning! • the top tether anchorages are not visible until the gap panel is folded down. Do not use the visible cargo tie down hooks, located on the floor behind the seats, to attach a child restraint tether anchor. • an incorrectly anchored tether strap could lead to increased head motion and possi...

  • Page 110

    While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving t...

  • Page 111

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be serious...

  • Page 112

    Warning! (continued) • if it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained ...

  • Page 113

    Not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air dir...

  • Page 114

    Warning! (continued) • check mounting of mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning. • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake pedal ...

  • Page 115

    Door latches check for positive closing, latching, and locking. Fluid leaks check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid (if equipped), or brake fluid leaks are suspected, t...

  • Page 117: Contents

    Understanding the features of your vehicle contents ! Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 ▫ inside day/night mirror — if equipped . . . .123 ▫ automatic dimming mirror — if equipped . . .123 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . .130 ▫ outside mir...

  • Page 118

    ! Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143 ▫ power seats — if equipped . . . . . . . . . . . . . .144 ▫ power lumbar — if equipped . . . . . . . . . . . .146 ▫ manual front seats forward/rearward adjustment . . . . . . . . . . . . . . . . . . . . . . . . .147 ▫ manual fro...

  • Page 119

    ▫ automatic headlight leveling — hid headlights only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170 ▫ adaptive bi-xenon high intensity discharge headlights — if equipped . . . . . . . . . . . . . . .170 ▫ headlight delay . . . . . . . . . . . . . . . . . . . . . .171 ▫ parking light...

  • Page 120

    ! Heated steering wheel — if equipped . .186 ! Electronic speed control — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .188 ▫ to activate . . . . . . . . . . . . . . . . . . . . . . . . . .189 ▫ to set a desired speed . . . . . . . . . . . . . . . . .189 ▫ to deactivate . . . . . ...

  • Page 121

    ▫ normal (fixed speed) electronic speed control mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215 ! Forward collision warning (fcw) with mitigation — if equipped . . . . . . . . . . . .219 ▫ forward collision warning (fcw) with mitigation operation . . . . . . . . . . . . . . . . ....

  • Page 122

    ▫ parksense® system usage precautions. . . . . . .240 ! Parkview® rear back up camera — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .243 ! Overhead console . . . . . . . . . . . . . . . . . .245 ▫ front map/reading lights — if equipped . . .246 ▫ courtesy lights . . . . . . . . ....

  • Page 123

    ▫ ignition off operation . . . . . . . . . . . . . . . . . .260 ! Commandview® sunroof with power shade — if equipped . . . . . . . . . . . . . . . . .260 ▫ opening sunroof — express . . . . . . . . . . . . . .261 ▫ opening sunroof — manual mode . . . . . . . . .261 ▫ closing sunroof — express. . . ...

  • Page 124

    ▫ cargo storage bins . . . . . . . . . . . . . . . . . . . .277 ▫ retractable cargo area cover — if equipped . .279 ▫ rear cargo tie-downs . . . . . . . . . . . . . . . . .280 ! Rear window features . . . . . . . . . . . . . .282 ▫ rear window wiper/washer . . . . . . . . . . . . .282 ▫ rear window ...

  • Page 125

    Mirrors inside day/night mirror — if equipped a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror hea...

  • Page 126

    Left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you. Note: the automatic dimming mirror feature is dis- abled when the vehicle is in reverse gear to improve re...

  • Page 127

    Note: the assist and 9–1–1 features operate through the uconnect® access service. These buttons will only operate as long as your uconnect® access service is active. Refer to your “uconnect® system supplement manual” for further information. Assist call the assist button is used to automatically con...

  • Page 128

    3. Once a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 call system may transmit the following important vehicle information to a 9-1-1 operator: • indication that the occupant placed a 9-1-1 call. • the vehicle brand. • the last known gps coordinates of the vehicle. 4. You ...

  • Page 129

    Warning! • if anyone in the vehicle could be in danger (e.G., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from a 9-1-1 operator. All occupants should exit the vehicle immediately and move to a safe location. (continued) warning! (continued) • the 9...

  • Page 130

    Warning! (continued) • modifications to any part of the 9-1-1 call system could cause the air bag system to fail when you need it. You could be injured if the air bag system is not there to help protect you. 9-1-1 call system limitations vehicles sold in canada and mexico do not have 9-1-1 call syst...

  • Page 131

    Warning! (continued) • the occupant restraint control module turns on the air bag warning light on the instrument panel if a malfunction in any part of the system is detected. If the air bag warning light is illumi- nated, the air bag system may not be working properly and the 9-1-1 system may not b...

  • Page 132

    Note: never place anything on or near the vehicle’s wireless and gps antennas. You could prevent wireless and gps signal reception, which can prevent your vehicle from placing an emergency call. Wireless and gps signal reception is required for the 9-1-1 call system to function properly. General inf...

  • Page 133

    Outside mirrors folding feature all outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions: • full forward position • full rearward position • normal position power folding outside mirrors — if equipped if equipped with power f...

  • Page 134

    Power mirrors the power mirror switch is located on the driver’s side door trim panel. The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. To adjust a mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror contro...

  • Page 135

    Power mirror preselected positions can be controlled by the optional memory seat feature. Refer to “driver memory seat” in “understanding the features of your vehicle” for further information. Outside automatic dimming mirrors — if equipped the outside mirrors will automatically adjust for glare fro...

  • Page 136

    Illuminated vanity mirrors to access an illuminated vanity mirror, flip down one of the visors. Lift the cover to reveal the mirror. The light will turn on automatically. Sun visor “slide-on-rod” feature — if equipped the sun visor “slide-on-rod” feature allows for addi- tional flexibility in positi...

  • Page 137

    When the vehicle is started, the bsm warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational. The bsm system sensors operate when the vehicle is in any forward gear or reverse and enters stand-by mode when the vehicle is in pa...

  • Page 138

    • the bsm system detection zone does not change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change. If the trailer or other object (i.E., bicycle, sports equipment) extends beyond the side of your v...

  • Page 139

    The bsm system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary. The bsm system will issue an alert during these types of zone entries. Entering from the side vehicles that move into your adjacent lanes from either side o...

  • Page 140

    Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Overtaking traffic if you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains ...

  • Page 141

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The bsm system will not alert you of objects t...

  • Page 142

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm (continued) warning! (continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicles m...

  • Page 143

    Rcp monitors the rear detection zones on both sides of the vehicle, for objects that are moving toward the side of the vehicle with a minimum speed of approximately 3 mph (5 km/h), to objects moving a maximum of approximately 20 mph (32 km/h), such as in parking lot situations. Note: in a parking lo...

  • Page 144

    Modes of operation three selectable modes of operation are available in the uconnect® system. Refer to “uconnect® settings/ customer programmable features” in “understanding your instrument panel” for further information. Blind spot alert lights only when operating in blind spot alert mode, the bsm ...

  • Page 145

    Note: the bsm system will store the current operating mode when the vehicle is shut off. Each time the vehicle is started the previously stored mode will be recalled and used. General information this vehicle has systems that operate on radio frequency that comply with part 15 of the federal communi...

  • Page 146

    Power seats — if equipped some models may be equipped with eight-way power driver and front passenger seats. The power seat switches are located on the outboard side of the seat. There are two switches that control the movement of the seat cushion and the seatback. Power seat switches 1 — seatback s...

  • Page 147

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 148

    Warning! (continued) • do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Caution! Do not place any article under a power seat or impede its abili...

  • Page 149

    Manual front seats forward/rearward adjustment some models may be equipped with a manual front passenger seat. The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor. While sitting in the seat, lift up on the bar located under the seat cu...

  • Page 150

    Manual front passenger seatback adjustment — recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired position and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the sea...

  • Page 151

    Heated seats — if equipped on some models, the front and rear seats may be equipped with heaters located in the seat cushions and seat backs. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex...

  • Page 152

    Front heated seats the front heated seats control buttons are located within the climate or controls screen of the touchscreen. • press the heated seat button once to turn the high setting on. • press the heated seat button a second time to turn the low setting on. • press the heated seat button a t...

  • Page 153

    You can choose from high, low or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high-level heating. Press the switch a second time to select low-l...

  • Page 154

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 155

    Vehicles equipped with remote start on models that are equipped with remote start, the ventilated seats can be programed to come on during a remote start. This feature can be programmed through the uconnect® system. Refer to “uconnect® settings” in “understand- ing your instrument panel” for further...

  • Page 156

    Active head restraints — front seats active head restraints are passive, deployable compo- nents, and vehicles with this equipment cannot be readily identified by any markings, only through visual inspection of the head restraint. The active head restraints (ahr) will be split in two halves, with th...

  • Page 157

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. Active head restraint (normal position) active head restraint (tilted) 3 understanding the features of your vehicl...

  • Page 158

    • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head restraints (ahr)” in “things to know before starting your vehicle” for further information. Warning! • do not place items over the top of the active head restraint, such as coats, seat cov...

  • Page 159

    The center head restraint has limited adjustment. Lift upward on the head restraint to raise it, or push down- ward on the head restraint to lower it. Warning! Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure t...

  • Page 160

    Note: be sure that the front seats are fully upright and positioned forward. This will allow the rear seatback to fold down easily. 1. Pull upward on the release lever to release the seat. Note: • do not fold the 60% rear seat down with the left outboard or rear center seat belt buckled. • do not fo...

  • Page 161

    To raise rear seat raise the rear seatback and lock it into place. If interfer- ence from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Warning! • be certain that the seatback is securely locked into position. If the seat...

  • Page 162

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Driver memory seat — if equipped this feature allows the driver to store up to two dif...

  • Page 163

    • the (1) and (2) buttons which are used to recall either of two pre-programmed memory profiles. Programming the memory feature note: to create a new memory profile, perform the following: 1. Cycle the vehicles ignition to the on/run position (do not start the engine). 2. Adjust all memory profile s...

  • Page 164

    • to set a memory profile to your rke transmitter, refer to “linking and unlinking the remote keyless entry transmitter to memory” in this section. Linking and unlinking the remote keyless entry transmitter to memory your rke transmitters can be programmed to recall one of two pre-programmed memory ...

  • Page 165

    Memory position recall note: the vehicle must be in park to recall memory positions. If a recall is attempted when the vehicle is not in park, a message will be displayed in the driver information display (did). Driver one memory position recall • to recall the memory settings for driver one using t...

  • Page 166

    Easy entry/exit seat this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. The distance the driver seat moves depends on where you have the driver seat positioned when you cycle the vehicles ignition to the off position. • when you ...

  • Page 167

    To open and close the hood to open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door. 2. Reach under the hood, move safety latch to the left and lift the hood. Hood release safety latch location 3 understanding the ...

  • Page 168

    Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle...

  • Page 169

    To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on, the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the o (off) position. Note: • your ve...

  • Page 170

    Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to the a (auto) position. When the system is on, the headlight delay feature is also on. This means the headlights will st...

  • Page 171

    Specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. Note: • if the windshield or automatic high beam mirror is replaced, the automatic high beam mirror must be re-aimed to ensure proper performance. See your local authorized dealer. • ...

  • Page 172

    To deactivate 1. Pull the multifunction lever toward you (or rearward in car) to manually deactivate the system (normal operation of low beams). 2. Push back on the multifunction lever once again to reactivate the system. Daytime running lights — if equipped the daytime running lights (low intensity...

  • Page 173

    Note: • each time the adaptive headlight system is turned on, the headlights will initialize by performing a brief sequence of rotations. • the adaptive headlight system is active only when the vehicle is moving forward. The adaptive headlight system can be turned on or off using the uconnect® syste...

  • Page 174

    The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pushed a second time, when the headlight sw...

  • Page 175

    The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer). When the headlights are on you can supplement the brightness of the odometer, trip odom- eter, radio and overhead console by rotating the control to its farthest position u...

  • Page 176

    Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. If the ignition is off and any door is left ajar for 10 minutes or the dimmer control is rotated all the way up to the dome on position for 10 minutes, the interior light...

  • Page 177

    Second time. The lights will also turn on when the unlock button on the remote keyless entry (rke) is pressed. Courtesy lights the courtesy lights can be turned on by pressing the top corner of the lens. To turn the lights off, press the lens a second time. Front map/reading light switches courtesy ...

  • Page 178

    Ambient light — if equipped the overhead console is equipped with an ambient light feature. This light casts illumination for improved visibil- ity of the floor and center console area. Multifunction lever the multifunction lever is located on the left side of the steering column. Ambient light mult...

  • Page 179

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside l...

  • Page 180

    Windshield wipers and washers the windshield wiper/washer controls are located on the multifunction lever on the left side of the steering col- umn. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “rear window fe...

  • Page 181

    Windshield wiper operation rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation. Caution! Always remove any buildup of snow that prevents the windshield wiper blades fro...

  • Page 182

    Intermittent wiper system use one of the four intermittent wiper settings when weather conditions make a single wiping cycle, with a variable delay between cycles, desirable. At driving speeds above 10 mph (16 km/h), the delay can be regulated from a maximum of approximately 18 seconds between cycle...

  • Page 183

    Windshield washer operation to use the washer, push on the end of the lever (toward the steering wheel) and hold while spray is desired. If the lever is pushed while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the end of the lever is released, and t...

  • Page 184

    Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist use the mist...

  • Page 185

    From the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of four settings to activate this feature. The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position one is the least sensitive, and wiper delay position four is ...

  • Page 186

    Not operate until the wiper switch is moved, vehicle speed is greater than 5 mph (8 km/h), or the shift lever/gear selector is moved out of the neutral position. Remote start mode inhibit — on vehicles equipped with remote starting system, rain sensing wipers are not operational when the vehicle is ...

  • Page 187

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Power tilt/telescoping st...

  • Page 188

    Note: for vehicles equipped with driver memory seat, you can use your remote keyless entry (rke) transmit- ter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to pre- programmed positions. Refer to “driver memory seat” in this section for further in...

  • Page 189

    Note: the engine must be running for the heated steering wheel to operate. Vehicles equipped with remote start on models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start through the uconnect® system. Refer to “uconnect® settings” in “u...

  • Page 190

    Electronic speed control — if equipped when engaged, the electronic speed control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The electronic speed control buttons are located on the right side of the steering wheel. Electronic speed control buttons 1 — on/off 4 — set-/...

  • Page 191

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 192

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate the electronic speed control with- out erasing the set speed from memory. Pressing the on/off button or turning the ignition switch off erases the set speed from...

  • Page 193

    To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set - button. The speed decrement shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pressing the set - button once will result in a 1 mph decrease in set s...

  • Page 194

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 195

    Warning! • adaptive cruise control (acc) is a convenience system. It is not a substitute for active driving involvement. It is always the driver’s responsibil- ity to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead; and, most importantly, brake ope...

  • Page 196

    Warning! (continued) you should switch off the acc system: when driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.E., in highway construction zones). When entering a turn lane or highway off ramp; when driving on roads that are winding, icy, snow- covere...

  • Page 197

    Adaptive cruise control (acc) operation the speed control buttons (located on the right side of the steering wheel) operates the acc system. Adaptive cruise control buttons 1 — normal (fixed speed) cruise control on/off 2 — set+/accel 3 — resume 4 — set-/decel 5 — distance setting — increase 6 — ada...

  • Page 198

    Note: any chassis/suspension or tire size modifications to the vehicle will effect the performance of the adaptive cruise control and forward collision warning system. Activating adaptive cruise control (acc) you can only engage acc if the vehicle speed is above 0 mph (0 km/h). The minimum set speed...

  • Page 199

    To turn the system off, push and release the adaptive cruise control (acc) on/off button again. At this time, the system will turn off and the did will display “adaptive cruise control (acc) off.” warning! Leaving the adaptive cruise control (acc) system on when not in use is dangerous. You could ac...

  • Page 200

    Warning! (continued) you could lose control and have a collision. Always leave the system off when you are not using it. To set a desired acc speed when the vehicle reaches the speed desired, push the set + button or the set - button and release. The did will display the set speed. If the system is ...

  • Page 201

    • the shift lever/gear selector is removed from the drive position. • the electronic stability control/traction control sys- tem (esc/tcs) activates. • the vehicle parking brake is applied. • driver seatbelt is unbuckled at low speeds. • driver door is opened at low speeds. • a trailer sway control ...

  • Page 202

    Warning! The resume function should only be used if traffic and road conditions permit. Resuming a set speed that is too high or too low for prevailing traffic and road conditions could cause the vehicle to accelerate or decelerate too sharply for safe operation. Failure to follow these warnings can...

  • Page 203

    To decrease speed while acc is set, the set speed can be decreased by pressing the set - button. The speed decrement shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pressing the set - button once will result in a 1 mph decrease in set speed. Each subseq...

  • Page 204

    • the acc system applies the brake down to a full stop when following a target vehicle. If an acc host vehicle follows a target vehicle to a standstill, the host vehicle will release the vehicle brakes two seconds after com- ing to a full stop. • the acc system maintains set speed when driving up hi...

  • Page 205

    Distance setting 3 bars (long) distance setting 2 bars (medium) 3 understanding the features of your vehicle 203.

  • Page 206

    To increase the distance setting, press the distance set- ting — increase button and release. Each time the button is pressed, the distance setting increases by one bar (longer). To decrease the distance setting, press the distance setting — decrease button and release. Each time the button is press...

  • Page 207

    • the system disengages. (refer to the information on acc activation). The maximum braking applied by acc is limited; how- ever, the driver can always apply the brakes manually, if necessary. Note: the brake lights will illuminate whenever the acc system applies the brakes. A proximity warning will ...

  • Page 208

    Overtake aid when driving with acc engaged and following a target vehicle, the system will provide an additional accelera- tion to assist in passing vehicles in front. This additional acceleration is triggered when the driver utilizes the left turn signal. In locations with left hand drive traffic, ...

  • Page 209

    Warning! When the acc system is resumed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle. Failure to follow these warnings can result in a collision and death or serious personal injury. Adaptive cruise control (acc) menu the did displays the curr...

  • Page 210

    • acc proximity warning • acc unavailable warning • the did will return to the last display selected after five seconds of no acc display activity display warnings and maintenance “wipe front radar sensor in front of vehicle” warning the “acc/fcw unavailable wipe front radar sensor” warning will dis...

  • Page 211

    To keep the acc system operating properly, it is impor- tant to note the following maintenance items: • always keep the sensor clean. Carefully wipe the sensor lens with a soft cloth. Be cautious not to damage the sensor lens. • do not remove any screws from the sensor. Doing so could cause an acc s...

  • Page 212

    “clean front windshield” warning the “acc/fcw limited functionality clean front windshield” warning will display and also a chime will indicate when conditions temporarily limit system per- formance. This most often occurs at times of poor visibil- ity, such as in snow or heavy rain and fog. The acc...

  • Page 213

    Service acc/fcw warning if the system turns off, and the did displays “acc/fcw unavailable service required”or “cruise/fcw unavail- able service required”, there may be an internal system fault or a temporary malfunction that limits acc func- tionality. Although the vehicle is still drivable under n...

  • Page 214

    Turns and bends when driving on a curve with acc engaged, the system may decrease the vehicle speed and acceleration for stability reasons, with no target vehicle detected. Once the vehicle is out of the curve the system will resume your original set speed. This is a part of normal acc system functi...

  • Page 215

    Lane changing acc may not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, acc has not yet detected the vehicle changing lanes and it may not detect the vehicle until it’s too late for the acc system to take action. Acc may not detect a vehic...

  • Page 216

    Narrow vehicles some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead. Stationary objects and vehicles acc does not react to stationary objects and ...

  • Page 217

    General information this vehicle has systems that operate on radio frequency that comply with part 15 of the federal communications commission (fcc) rules and with industry canada standards rss- gen/210/220/310. Operation is subject to the following two conditions: 1. The device may not cause harmfu...

  • Page 218

    Warning! In the normal cruise control mode, the system will not react to vehicles ahead. In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to vehicle distance is ...

  • Page 219

    • if the button is continually pressed, the set speed will continue to increase in 5 mph increments until the button is released. The increase in set speed is reflected in the did display. To decrease speed when the normal (fixed speed) cruise control is set, you can decrease speed by pressing the s...

  • Page 220

    To cancel the following conditions will cancel the normal (fixed speed) electronic speed control without clearing the memory: • the brake pedal is applied. • the cancel button is pressed. • the electronic stability control/traction control sys- tem (esc/tcs) activates. • the vehicle parking brake is...

  • Page 221

    Forward collision warning (fcw) with mitigation — if equipped forward collision warning (fcw) with mitigation operation the forward collision warning (fcw) system with mitigation provides the driver with audible warnings, visual warnings (within the did), and may apply a brake jerk to warn the drive...

  • Page 222

    When the system determines a collision with the vehicle in front of you is no longer probable, the warning message will be deactivated. Note: • the minimum speed for fcw activation is 5 mph (10 km/h). • the fcw alerts may be triggered on objects other than vehicles such as guard rails or sign posts ...

  • Page 223

    Warning! Forward collision warning (fcw) is not intended to avoid a collision on its own, nor can fcw detect every type of potential collision. The driver has the responsibility to avoid a collision by controlling the vehicle via braking and steering. Failure to follow this warning could lead to ser...

  • Page 224

    Changing fcw and active braking status the fcw sensitivity and active braking settings are programmable through the uconnect® system. Refer to “uconnect® settings” in “understanding your instru- ment panel” for further information. The default status of fcw is the “far” setting and the active brakin...

  • Page 225

    Fcw limited warning if the system turns off, and the did displays “acc/fcw limited functionality” or “acc/fcw limited function- ality clean front windshield” momentarily, there may be a condition that limits fcw functionality. Although the vehicle is still drivable under normal conditions, the activ...

  • Page 226

    Active until the vehicle speed is increased to approxi- mately 7 mph (11 km/h) or above. When in reverse and above the system’s operating speed, a warning will appear within the driver information display (did) indicating the vehicle speed is too fast. The system will become active again if the vehi...

  • Page 227

    Parksense® display when the vehicle is in reverse, the did will display the park assist ready system status. The system will indicate a detected obstacle by showing a single arc in the left and/or right rear regions based on the obstacle’s distance and location relative to the vehicle. If an obstacl...

  • Page 228

    Single 1/2 second tone slow tone 226 understanding the features of your vehicle.

  • Page 229

    Fast tone continuous tone 3 understanding the features of your vehicle 227.

  • Page 230

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-39 in (200-100 cm) ...

  • Page 231

    Enabling and disabling parksense® parksense® can be enabled and disabled with the parksense® switch. When the parksense® switch is pressed to disable the system, the instrument cluster will display the “parksense off” message for approximately five seconds. Refer to “driver information dis- play (di...

  • Page 232

    If “parksense unavailable wipe rear sen- sors” appears in the driver information display (did) make sure the outer surface and the underside of the rear fascia/bumper is clean and clear of snow, ice, mud, dirt or other obstruction and then cycle the ignition. If the message continues to appear, see ...

  • Page 233

    • parksense®, when on, will reduce the volume of the radio when it is sounding a tone. • clean the parksense® sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not workin...

  • Page 234

    Warning! • drivers must be careful when backing up even when using parksense®. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue...

  • Page 235

    Parksense® front and rear park assist — if equipped the parksense® park assist system provides visual and audible indications of the distance between the rear and/or front fascia and a detected obstacle when backing up or moving forward, e.G. During a parking maneuver. Refer to parksense® system usa...

  • Page 236

    Parksense® warning display the parksense® warning screen will only be displayed if sound and display is selected from the customer - programmable features section of the uconnect® sys- tem. Refer to # uconnect® settings” in “understanding your instrument panel” for further information. The parksense...

  • Page 237

    Vehicle moves closer to the object, the display will show the single arc moving closer to the vehicle and the tone will change from a single 1/2 second tone to slow, to fast, to continuous. Single 1/2 second tone slow tone 3 understanding the features of your vehicle 235.

  • Page 238

    The vehicle is close to the obstacle when the did display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: fast tone continuous tone 236 understanding the features of your vehicle.

  • Page 239

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-39 in (200-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) front distance (in/cm) greater than 47 in (120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible al...

  • Page 240

    Front park assist audible alerts parksense® will turn off the front park assist audible alert (chime) after approximately 3 seconds when an obstacle has been detected, the vehicle is stationary, and brake pedal is applied. Adjustable chime volume settings front and rear chime volume settings can be ...

  • Page 241

    Service the parksense® park assist system during vehicle start up, when the parksense® system has detected a faulted condition, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the # parksense unavailable wipe rear sensors # , # parksense unavailable w...

  • Page 242

    Cleaning the parksense® system clean the parksense® sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could dam- age the sensors. Parksense® system usage precautions note: • ensure that the front and rear bumper ar...

  • Page 243

    • use the parksense® switch to turn the parksense® system off if objects such as bicycle carriers, trailer hitches, etc. Are placed within 12 in (30 cm) from the rear fascia/bumper. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the “parksense u...

  • Page 244

    Warning! • drivers must be careful when backing up even when using parksense®. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue...

  • Page 245

    Parkview® rear back up camera — if equipped your vehicle may be equipped with the parkview® rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever/gear selector is put into reverse. The image will be displayed on the navigation...

  • Page 246

    Of the vehicle to assist with aligning to a hitch/receiver. The following table shows the approximate distances for each zone: zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm) yellow 1 ft - 6.5 ft (30 cm - 2 m) green 6.5 ft or greater (2 m or greater) warning! Drivers must be carefu...

  • Page 247

    Caution! • to avoid vehicle damage, parkview® should only be used as a parking aid. The parkview® camera is unable to view every obstacle or object in your drive path. • to avoid vehicle damage, the vehicle must be driven slowly when using parkview® to be able to stop in time when an obstacle is see...

  • Page 248

    Front map/reading lights — if equipped lights are mounted in the overhead console. Each light can be turned on by pressing the switch on either side of the console. These buttons are backlit for night time visibility. To turn the lights off, press the switch a second time. The lights also turn on wh...

  • Page 249

    Courtesy lights the courtesy lights can be turned on by pressing the top corner of the lens. To turn the lights off, press the lens a second time. Sunglasses bin door at the front of the console a compartment is provided for the storage of a pair of sunglasses. The storage compart- ment access is a ...

  • Page 250

    Garage door opener — if equipped homelink® replaces up to three hand-held transmitters that operate devices such as garage door openers, motor- ized gates, lighting or home security systems. The homelink® unit is powered by your vehicles 12 volt battery. The homelink® buttons, located on the overhea...

  • Page 251

    Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the d...

  • Page 252

    1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keeping the homelink® indicator light in view. 3. Push and hold the homelink® button you want to program while you push and hold the hand-...

  • Page 253

    Firmly push and release the “learn” or “train- ing” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the learn/train mode. Note: you have 30 seconds in which to initiate the next step after the learn button has been pushed. 6. Retu...

  • Page 254

    2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light in view. 3. Push and hold the homelink® button you want to program while you push and hold the hand-held transmitter button. 4. Continue to hold...

  • Page 255

    Canadian/gate operator programming for programming transmitters in canada/united states that require the transmitter signals to “time-out” after several seconds of transmission. Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission ...

  • Page 256

    • if the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the homelink® button is pushed. • to program the two remaining homelink® buttons, repeat each step for each remaining button. Do not erase the channels. If you unplugged the garage...

  • Page 257

    The homelink® universal transceiver is disabled when the vehicle security alarm is active. Troubleshooting tips if you are having trouble programming homelink®, here are some of the most common solutions: • replace the battery in the original hand-held transmit- ter. • push the learn button on the g...

  • Page 258

    Warning! (continued) use a garage door opener without these safety fea- tures. Call toll-free 1–800–355–3515 or, on the internet at homelink.Com for safety information or assis- tance. General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject t...

  • Page 259

    Power sunroof — if equipped the power sunroof switch is located between the sun visors on the overhead console. Warning! • never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to children. Do ...

  • Page 260

    Warning! (continued) • do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. Injury may result. Opening sunroof — express press the switch rearward and release it within one-half second and the sunroof w...

  • Page 261

    Pinch protect feature this feature will detect an obstruction in the opening of the sunroof during express close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and ...

  • Page 262

    Sunroof maintenance use only a nonabrasive cleaner and a soft cloth to clean the glass panel. Ignition off operation note: • the power sunroof switch can remain active for up to approximately ten minutes after the vehicles ignition is cycled to the off position. Opening either front door will cancel...

  • Page 263

    Warning! • never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with keyless enter-n-go™ in the acc or on/run mode. Occupants, part...

  • Page 264

    Movement. The sunroof and sunshade will remain in a partially opened condition until the switch is pushed and held rearward again. Closing sunroof — express press the switch forward and release it within one-half second and the sunroof will close automatically from any position. The sunroof will clo...

  • Page 265

    The movement and the shade will remain in a partially opened condition until the switch is pushed and held rearward again. Closing power shade — express press the switch forward and release it within one-half second and the shade will close automatically from any position. If the sunroof is complete...

  • Page 266

    Sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to express close. Note: if three consecutive sunroof close attempts result in pinch protect reversals, the fourth close attempt will be a manual close movement with pinch protect d...

  • Page 267

    Electrical power outlets your vehicle is equipped with 12 volt (13 amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The power outlets are labeled with either a “key” or a “battery” symbol to indicate how the outlet is power...

  • Page 268

    The front power outlet is located inside the storage area on the center stack of the instrument panel. Push inward on the storage lid to open the compartment and gain access to this power outlet. In addition to the front power outlet, there is also a power outlet located in the storage area of the c...

  • Page 269

    The rear power outlet is located in the right rear cargo area. Note: the rear power outlet can be switched from switched “ignition” only to constant “battery” powered all the time. See your local authorized dealer for details. Rear power outlet power outlet right rear quarter panel fuse 3 understand...

  • Page 270

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 271

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 272

    The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. To avoid overloading the circuit, chec...

  • Page 273

    Cupholders there are two cupholders for the front seat passengers located in the center console. There are two cupholders for the rear seat passengers located in the fold-down center armrest. Front cupholders rear cupholders 3 understanding the features of your vehicle 271.

  • Page 274

    Storage glove compartment the glove compartment is located on the right side of the instrument panel. To open the glove compartment, pull outward on the latch and lower the glove compartment door. Glove compartment opened glove compartment 272 understanding the features of your vehicle.

  • Page 275

    Door storage large storage areas are built into the door panels for easy access. Console features the center console contains both an upper and a lower storage area. Door panel storage storage compartment 3 understanding the features of your vehicle 273.

  • Page 276

    To open the upper storage compartment, pull upward on the small latch located on the lid. Lift upward on the larger of the latches to access the lower storage compartment. Storage compartment latches lower storage compartment 274 understanding the features of your vehicle.

  • Page 277

    Your vehicle may have an optional cd or dvd player located in the center console. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Cargo area features rechargeable flashlight...

  • Page 278

    Press in on the flashlight to release it. To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Press and release three-press switch 276 understanding the features of your vehicle.

  • Page 279

    Cargo storage bins there are up to four removable storage bins located in the rear cargo area. There are two storage bins located on either side of the cargo area. Note: if your vehicle is equipped with a rear sub- woofer, the passenger side cargo area will not be avail- able. Rear storage bin 3 und...

  • Page 280

    Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether hook (attached to the bottom of the load floor) to the liftgate opening. Tether strap lower storage bins 278 understanding the features of your vehicle.

  • Page 281

    Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the...

  • Page 282

    Warning! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. D...

  • Page 283

    Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. • cargo tie-down hooks are not safe anchors for a child seat t...

  • Page 284

    Rear window features rear window wiper/washer the rear wiper/washer controls are located on the mul- tifunction lever on the left side of the steering column. The rear wiper/washer is operated by rotating a switch, located at the middle of the lever. Rotate the center portion of the lever upward to ...

  • Page 285

    Release of the switch, the wipers will resume the continu- ous rear wiper operation. When this rotary control is in the off position, rotating it downward will activate the rear washer pump which will continue to operate as long as the switch is held. Once the switch is released it will return to th...

  • Page 286

    Caution! (continued) • do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • keep all objects a safe distance from the window. Roof luggage rack — if equipped the crossbars and siderails are designed to carry the weight on vehicles equipped with...

  • Page 287

    • if (or any metallic object) is placed over the satellite radio antenna (if equipped), you may experience in- terruption of satellite radio reception. For improved satellite radio reception, avoid placing the rear cross- bar over the satellite radio antenna. Caution! • to prevent damage to the roof...

  • Page 288

    Warning! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack cautions when carrying cargo on your roof rack. 286 understanding the features of y...

  • Page 289: Contents

    Understanding your instrument panel contents ! Instrument panel features . . . . . . . . . .290 ! Instrument cluster . . . . . . . . . . . . . . . . .291 ! Instrument cluster descriptions . . . . .292 ! Driver information display (did). . . . . .301 ▫ did displays . . . . . . . . . . . . . . . . . ....

  • Page 290

    ! Uconnect® radios — if equipped . . . . . . . .359 ! Ipod®/usb/mp3 control — if equipped . . .359 ! Uconnect® rear seat entertainment system — if equipped . . . . . . . . . . . . . . . . .360 ▫ getting started . . . . . . . . . . . . . . . . . . . . . . .360 ▫ dual video screen . . . . . . . . . . ...

  • Page 291

    ! Climate controls . . . . . . . . . . . . . . . . . . .385 ▫ general overview . . . . . . . . . . . . . . . . . . . . .385 ▫ climate control functions . . . . . . . . . . . . . . .391 ▫ automatic temperature control (atc) . . . . . .392 ▫ operating tips . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 292

    Instrument panel features 1 — air outlet 6 — lower switch bank 11 — hood release 2 — instrument cluster 7 — hazard switch 12 — fuel door release 3 — radio 8 — storage bin (sd card, aux, usb media hub) 13 — headlight switch 4 — glove compartment 9 — esc button 14 — dimmer control 5 — climate controls...

  • Page 293

    Instrument cluster 4 understanding your instrument panel 291.

  • Page 294

    Instrument cluster descriptions 1. Tachometer indicates the engine speed in revolutions per minute (rpm x 1000). 2. Seat belt reminder light when the ignition switch is first turned to the on/run position, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if t...

  • Page 295

    5. Front fog light indicator — if equipped this indicator will illuminate when the front fog lights are on. 6. Upper left selectable did this area of the cluster will display selectable informa- tion such as compass, outside temperature, etc. For further information, refer to “driver information dis...

  • Page 296

    If the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing. Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel e...

  • Page 297

    Caution! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear cont...

  • Page 298

    Has been corrected. If the problem is related to the brake booster, the abs pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A le...

  • Page 299

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 13. Fuel gauge/fuel door reminder the fuel pump symbol points to the side ...

  • Page 300

    Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and...

  • Page 301

    Odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If she/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the rep...

  • Page 302

    19. Electronic stability control (esc) off indicator light — if equipped this light indicates the electronic stability con- trol (esc) is off. 20. Electronic stability control (esc) activation/ malfunction indicator light — if equipped the “esc activation/malfunction indicator light” in the instrume...

  • Page 303

    21. Park/headlight on indicator — if equipped this indicator will illuminate when the park lights or headlights are turned on. Driver information display (did) the driver information display (did) features a driver- interactive display that is located in the instrument cluster. Driver information di...

  • Page 304

    The did menu items consists of the following: • digital speedometer • vehicle info • terrain — if equipped • srt performance— if equipped • driver assist • fuel economy • trip • stop/start — if equipped • audio • stored messages • screen setup • speed warning — if equipped the system allows the driv...

  • Page 305

    • up arrow button push and release the up arrow button to scroll upward through the main menu and submenus. • down arrow button push and release the down arrow button to scroll downward through the main menu and submenus. • right arrow button push and release the right arrow button to access the inf...

  • Page 306

    3. Reconfigurable telltales/information 4. Telltales/indicators 5. Shift lever status (prndl) 6. Selectable information (compass, temp, range to empty, trip a, trip b, average fuel economy, current fuel economy) 7. Air suspension status — if equipped 8. 4wd status — status 9. Selectable gauge 1 the ...

  • Page 307

    Is in the run state. Examples of this message type are “remote start aborted - door ajar” and “press brake pedal and push button to start”. • five second unstored messages when the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then ret...

  • Page 308

    3. Without pushing the brake pedal, push and release the engine start/stop button once to return the ignition to the off/lock position. Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Did messa...

  • Page 309

    • speed warning exceeded • parking brake engaged • brake fluid low • service electronic braking system • engine temperature hot • battery voltage low • service electronic throttle control • lights on • right turn signal light out • left turn signal light out • turn signal on • vehicle not in park • ...

  • Page 310

    • doors open • liftgate open • gear not available • shift not allowed • vehicle speed to high to shift • shift to neutral then drive or reverse • autostick unavailable service required • automatic unavailable use autostick service req. • transmission getting hot press brake • trans. Hot stop safely ...

  • Page 311

    • vehicle cannot be lowered door open • off road 2 watch for clearance • entry/exit watch for clearance • air suspension temporarily disabled for jacking and tire change • battery low start engine to change ride height the reconfigurable telltales section is divided into the white telltales area on ...

  • Page 312

    Did amber telltales this area will show reconfigurable amber caution tell- tales. These telltales include: • low fuel telltale when the fuel level reaches approximately 3.0 gal (11.0 l) this light will turn on, and remain on until fuel is added. • windshield washer fluid low indicator this telltale ...

  • Page 313

    • anti-lock brake (abs) this light will turn on when the abs system is not functioning and service is required. If the abs light is on the brake system should be serviced as soon as possible. • malfunction indicator light (mil) this light will turn on when certain conditions exist. The vehicle shoul...

  • Page 314

    Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. • oil temperature warning light this telltale indicates engine oil temperature is high. If the light turns on while driving, stop the ...

  • Page 315

    Required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • engine temperature warning light this light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches h, this indicator will illuminate and...

  • Page 316

    • air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to the on/run position. Refer to “oc- cupant restraints” in “things to know before starting your vehicle” of your owners manual for further information. Did green tellta...

  • Page 317

    Speedometer push and release the left or right arrow button to toggle between the speedometer dis- play type (analog or digital). Mph to km/h push and release the up or down arrow button until the mph to km/h icon is highlighted in the did. Push and release the ok button to change the display betwee...

  • Page 318

    If one or more tires have low pressure, “inflate tire to xx” is displayed with the vehicle icon and the tire pressure values in each corner of the icon with the pressure value of the low tire displayed in a different color than the other tire pressure values. If the tire pressure system requires ser...

  • Page 319

    Driver assist — if equipped push and release the up or down arrow button until the driver assist display icon/title is highlighted in the did. For further informa- tion, refer to “adaptive cruise control (acc) — if equipped” in “understanding the features of your vehicle”. Fuel economy push and rele...

  • Page 320

    Audio push and release the up or down arrow button until the audio menu icon/title is high- lighted in the did. Stored messages push and release the up or down arrow button until the messages menu icon/title is highlighted in the did. This feature shows the number of stored warning messages. Pushing...

  • Page 321

    Screen setup driver selectable items current gear • on • off upper left • none • compass • outside temp (default setting) • time • range to empty (rte) • fuel economy average • fuel economy current • trip a • trip b upper right • none • compass (default setting) • outside temp • time • range to empt...

  • Page 322

    Restore to defaults (restores all settings to default settings) • cancel • okay uconnect® settings the uconnect® system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allow you to access and change the customer program...

  • Page 323

    Buttons on the faceplate buttons on the faceplate are located below the uconnect® system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side of the climate controls in the center of the instru- ment panel. Turn the control knob to scroll...

  • Page 324

    Buttons on the touchscreen buttons on the touchscreen are accessible on the uconnect® display. Customer programmable features — uconnect® 5.0 personal settings push the more button on the faceplate to display the menu setting screen. In this mode the uconnect® system allows you to access programmabl...

  • Page 325

    And release the “auto” or “manual” button on the touchscreen. Then press the arrow back button on the touchscreen. Note: when day or night is selected for the display mode, the usage of the parade mode feature will cause the radio to activate the display brightness day control even though the headli...

  • Page 326

    • set language when in this display, you may select one of multiple languages (english/français/español) for all display no- menclature, including the trip functions and the naviga- tion system (if equipped). Press the “set language” button on the touchscreen, then press the desired lan- guage butto...

  • Page 327

    • show command list when in this display, you may change the show com- mand list settings. To change the show command list settings, press the “show command list” button on the touchscreen and select from “always,” “with help” or “never.” press the back arrow button on the touchscreen to return to t...

  • Page 328

    “sound only” or “sounds and display” button. Then press the back arrow button on the touchscreen. Refer to “parksense®” in “understanding the features of your vehicle” for system function and operating information. • tilt mirrors in reverse when this feature is selected, the exterior sideview mirror...

  • Page 329

    8 mph (12 km/h), the transmission is shifted into park or the ignition is switched to the off position. To set the parkview® backup camera delay push the more but- ton on the faceplate, the “settings” button on the touch- screen, then the “safety & driving assistance” button on the touchscreen. Pres...

  • Page 330

    • headlight illumination on approach when this feature is selected, it allows the adjustment of the amount of time the headlights remain on after the doors are unlocked with the remote keyless entry (rke) transmitter. To change the illuminated approach status, press the “illuminated approach” button...

  • Page 331

    Press the “daytime running lights” button on the touch- screen and make your selection. Press the back arrow button on the touchscreen to return to the previous menu. • flash lights with lock when this feature is selected, the headlights will flash when the doors are locked or unlocked with the remo...

  • Page 332

    • flash lights w/lock when this feature is selected, the exterior lights will flash when the doors are locked or unlocked with the remote keyless entry (rke) transmitter or the passive entry feature. To make your selection, press the “flash lights w/lock” button on the touchscreen and select from “o...

  • Page 333

    Note: passive entry — if equipped. If “all” is selected, all doors will unlock no matter which passive entry door handle is grasped. If “driver” is selected, only the driver’s door will unlock when the driver’s door is grasped. • passive entry this feature allows you to lock and unlock the vehicle’s...

  • Page 334

    Auto comfort systems — if equipped after pressing the “auto-on comfort & remote start” button on the touchscreen the following settings will be available: • auto-on driver heated/ventilated seat & steering wheel with vehicle start — if equipped when this feature is selected the driver’s heated seat ...

  • Page 335

    “60,” or “90” seconds to select your desired time interval. Press the back arrow button on the touchscreen to return to the previous menu. • engine off power delay when this feature is selected, the power window switches, radio, uconnect® phone system (if equipped), dvd video system (if equipped), p...

  • Page 336

    • tire jack mode when this feature is selected the air suspension system is disabled to prevent auto leveling of the suspension, while the vehicle is on a jack changing a tire. To make your selection, press the “tire jack mode” button on the touchscreen, select “on” or “off” followed by pressing the...

  • Page 337

    Note: keep magnetic materials away from the top of the instrument panel, such as ipod’s, mobile phones, lap- tops and radar detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. • perform compass calibration pre...

  • Page 338

    The scale between the “+” and “–” buttons on the touchscreen. Press the back arrow/done button on the touchscreen to return to the previous menu. • balance/fade this feature allows you to adjust the balance and fade settings. Press and drag the speaker icon or use the arrows to adjust, tap the “c” i...

  • Page 339

    The touchscreen, select “on” or “off.” press the back arrow/done button on the touchscreen to return to the previous menu. Phone/bluetooth® after pressing the “phone/bluetooth” button on the touchscreen the following settings will be available: • paired devices this feature shows which phones are pa...

  • Page 340

    Note: siriusxm travel link is a separate subscription and is available for u.S. Residents only. Restore settings after pressing the “restore settings” button on the touchscreen the following settings will be available: • restore settings when this feature is selected it will reset the display, clock...

  • Page 341

    Customer programmable features — uconnect® 8.4 personal settings press the “apps” or the “controls” button on the touch- screen, then press the “settings” button on the touch- screen to display the menu setting screen. In this mode the uconnect® system allows you to access program- mable features th...

  • Page 342

    Note: when day or night is selected for the display mode, the usage of the parade mode feature will cause the radio to activate the display brightness day control even though the headlights are on. • display brightness with headlights on when in this display, you may select the brightness with the h...

  • Page 343

    • set language when in this display, you may select one of multiple languages (english/français/español) for all display no- menclature, including the trip functions and the naviga- tion system (if equipped.) press the “set language” button on the touchscreen and then press the desired language butt...

  • Page 344

    • navigation turn-by-turn displayed in cluster — if equipped when this feature is selected, to make your selection, press the “navigation turn-by-turn displayed in clus- ter” button on the touchscreen, until a check-mark ap- pears next to the setting, showing that setting has been selected. Press th...

  • Page 345

    Time with gps” button on the touchscreen until a check- mark appears next to the setting, showing that setting has been selected. Press the back arrow button on the touch- screen to return to the previous menu. • set time hours this feature will allow you to adjust the hours. The “sync time with gps...

  • Page 346

    Safety & driving assistance after pressing the “safety & driving assistance” button on the touchscreen the following settings will be avail- able: • forward collision warning — if equipped the front collision warning (fcw) feature provides an audible and/or visual warning to potential forward collis...

  • Page 347

    • parksense® the parksense® system will scan for objects behind the vehicle when the transmission shift lever is in reverse and the vehicle speed is less than 11 mph (18 km/h). It will provide an alert (audible and/or visual) to indicate the proximity to other objects. The system can be enabled with...

  • Page 348

    Arrow button on the touchscreen to return to the previous menu. Parksense® will retain its last known configura- tion state through ignition cycles. • tilt side mirrors in reverse when this feature is selected, the exterior side view mirrors will tilt downward when the ignition is in the run positio...

  • Page 349

    • parkview® backup camera active guidelines your vehicle may be equipped with the parkview® rear back up camera active guidelines that allows you to see active guidelines over the parkview back up camera display whenever the shift lever is put into reverse. The image will be displayed on the radio t...

  • Page 350

    Had been selected. Press the back arrow button on the touchscreen to return to the previous menu. • hill start assist — if equipped when this feature is selected, the hill start assist (hsa) system is active. Refer to “electronic brake control system” in “starting and operating” for system function ...

  • Page 351

    • headlights with wipers — if equipped when this feature is selected, and the headlight switch is in the auto position, the headlights will turn on ap- proximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by th...

  • Page 352

    With lock” button on the touchscreen, until a check-mark appears next to setting, showing that setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu, or push the back button on the faceplate. Doors & locks after pressing the doors & locks button on ...

  • Page 353

    Next to setting, indicating that the setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu. • sound horn with lock when this feature is selected, the horn will sound when the door locks are activated. To make your selection, press either the “off,” ...

  • Page 354

    Note: if the vehicle is programmed 1st press of key fob unlocks “all doors,” all doors will unlock no matter which passive entry equipped door handle is grasped. If 1st press of key fob unlocks “driver door” is pro- grammed, only the driver’s door will unlock when the driver’s door is grasped. With ...

  • Page 355

    Note: the seat will return to the memorized seat location (if recall memory with remote key unlock is set to on) when the remote keyless entry (rke) transmitter is used to unlock the door. Refer to “driver memory seat” in “understanding the features of your vehicle” for further information. • power ...

  • Page 356

    Engine off options after pressing the engine off options button on the touchscreen the following settings will be available. • easy exit seat — if equipped this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection...

  • Page 357

    The touchscreen until a check-mark appears next to setting, showing that setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu. Suspension — if equipped after pressing the suspension button on the touchscreen the following settings will be available...

  • Page 358

    Check-mark is removed showing the system has been deactivated. Press the back arrow button on the touch- screen to return to the previous menu. • wheel alignment mode before performing a wheel alignment this mode must be enabled. Refer to your authorized dealer for further information. Audio after p...

  • Page 359

    • surround sound — if equipped this feature provides simulated surround sound mode. To make your selection, press the “surround sound” button on the touchscreen, select “on” or “off.” press the back arrow button on the touchscreen to return to the previous menu. • aux volume offset — if equipped thi...

  • Page 360

    Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touch- screen, the following settings will be available: • channel skip siriusxm can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scannin...

  • Page 361

    Select “ok” to restore, or “cancel” to exit. Once the settings are restored, a pop up appears stating # settings reset to default. # clear personal data after pressing the “clear personal data settings” button on the touchscreen the following settings will be avail- able: • clear personal data when ...

  • Page 362

    May not fully support the ipod® control features. Please visit apple’s website for software updates. For further information, refer to the uconnect® supple- ment manual. Uconnect® rear seat entertainment system — if equipped your rear seat entertainment system is designed to give your family years o...

  • Page 363

    • turn on the rear seat entertainment system by push- ing the power button on the remote control. • when the video screen(s) are open and a dvd/blu- ray™ disc is inserted into the disc player, the screen(s) turn(s) on automatically, the headphone transmitters turn on and playback begins. • with the ...

  • Page 364

    • the system can be controlled by the front seat occu- pants utilizing either the touchscreen radio, or by the rear seat occupants using the remote control. Dual video screen note: typically there are two different ways to operate the features of the rear seat entertainment system. • the remote cont...

  • Page 365

    To view a blu-ray™ insert the disc into the blu-ray™ disc player. Playback will begin automatically after the blu- ray™ disc is recognized by the disc drive. If playback does not begin automatically after the disc is inserted into blu-ray™ disc player follow these steps: using the touchscreen radio ...

  • Page 366

    Is not highlighted select button to access controls for screen 1/channel 1 source. 2. Rse power press to turn rse on/off. 3. Rse mute mute rear headphones for the current ignition cycle. Pressing mute again will unmute rear headphones. 4. Rse remote control lock out press to enable/disable remote co...

  • Page 367

    Using the remote control • select an audio channel (rear 1 for driver’s side rear screen and rear 2 for passenger’s side rear screen), then press the source key and using the up and down arrows, highlight disc from the menu and press the ok button. • press the popup/menu key to navigate the disc men...

  • Page 368

    When connecting an external source to the aux/hdmi input, ensure to follow the standard color coding for the audio/video jacks: 1. Hdmi input 2. Right audio in (red) 3. Left audio in (white) 4. Video in (yellow) note: certain high-end video games, such as playsta- tion4 and xbox one will exceed this...

  • Page 369

    Using the touchscreen radio controls 1. Press the media button on the uconnect® radio touch- screen. 2. Press the rear media button to display the rear media control screen. 3. Press the 1 or 2 buttons on the touchscreen, the select source button on the touchscreen and then the disc button on the to...

  • Page 370

    Note: pressing the screen on the radio while a dvd or blu-ray™ disc is playing, brings up the basic remote control functions for dvd play such as scene selection, play, pause, ff, rw, and stop. Pressing the x in the upper corner will turn off the remote control screen functions. Important notes for ...

  • Page 371

    Blu-ray™ disc player remote control — if equipped controls and indicators 1. Power — turns the screen and wireless headphone transmitter for the selected channel on or off. To hear audio while the screen is closed, push the power button to turn the headphone transmitter on. 2. Channel selector indic...

  • Page 372

    7. !! ! — push and hold to fast forward through the current audio track or video chapter. 8. ! / % (play/pause) — begin/resume or pause disc play. 9. Four colored buttons — push to access blu-ray™ disc features. 10. Popup/menu — push to bring up repeat and shuffle options, the blu-ray™ disc popup me...

  • Page 373

    Headphones operation the headphones receive two separate channels of audio using an infrared transmitter from the video screen. If no audio is heard after increasing the volume control, verify that the screen is turned on, the channel is not muted and the headphone channel selector switch is on the ...

  • Page 374

    Controls the headphone power indicator and controls are located on the right ear cup. Note: the rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video sys...

  • Page 375

    5. To cancel out of the mode selection menu, push the back button on the remote control. Replacing the headphone batteries each set of headphones requires two aaa batteries for operation. To replace the batteries: • locate the battery compartment on the left ear cup of the headphones, and then slide...

  • Page 376

    For any general, special, direct, indirect, incidental, consequential, exemplary, pu- nitive or other damages of any kind or nature whatsoever. Some states and jurisdictions may not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you...

  • Page 377

    Display settings when watching a video source (blu-ray™ disc or dvd video with the disc in play mode, aux video, etc.), pushing the remote control’s setup button activates the display settings menu. These settings control the appear- ance of the video on the screen. The factory default settings are ...

  • Page 378

    Listening to audio with the screen closed to listen to only audio portion of the channel with the screen closed: • set the audio to the desired source and channel. • close the video screen. • to change the current audio mode, push the remote control’s source button. This will automatically se- lect ...

  • Page 379

    Match in order for the disc to play. If the region code for the dvd disc does not match the region code for the player, the disc will not play. Dvd audio support when a dvd-audio disc is inserted in the blu-ray™ disc player, the dvd-audio title on the disc is played by default (most dvd-audio discs ...

  • Page 380

    • for cd data (or cd-rom) discs, always use the iso-9660 (level 1 or level 2), joliet, or romeo format. Other formats (such as udf, hfs, or others) are not supported. • the player recognizes a maximum of 512 files and 99 folders per cd-r and cd-rw disc. • mixed media recordable dvd formats will only...

  • Page 381

    • other compression formats such as aac, mp3 pro, ogg vorbis, and atrac3 will not play. The blu-ray™ player will automatically skip the file and begin play- ing the next available file. • if you are creating your own files, the recommended fixed bit rate for mp3 files is between 96 and 192kbps and t...

  • Page 382

    Product agreement this product incorporates copyright protection technol- ogy that is protected by u.S. Patents and other intellec- tual property rights. Use of this copyright protection technology must be authorized by macrovision, and is intended for home or other limited viewing uses other- wise ...

  • Page 383

    Steering wheel audio controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a push-button in the center and controls the volume and mode of the s...

  • Page 384

    The button located in the center of the left-hand control will tune to the next preset station that you have pro- grammed in the radio preset button. Cd player pushing the top of the switch once will go to the next track on the cd. Pushing the bottom of the switch once will go to the beginning of th...

  • Page 385

    Radio operation and mobile phones under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the mobile phone antenna. This condition is not harmful to the radio. If your radio...

  • Page 386

    This device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that m...

  • Page 387

    • consult the dealer or an experienced radio technician for help. Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. This system can be operated through either the controls on the instrument panel or through the uconnect® system dis-...

  • Page 388

    Buttons on the touchscreen the buttons on the touchscreen are accessible on the uconnect® system screen. Button descriptions (applies to both the buttons on the faceplate and the buttons on the touchscreen) 1. Max a/c button press and release to change the current setting, the indicator illuminates ...

  • Page 389

    This function again will cause the max a/c operation to switch into manual mode and the max a/c indicator will turn off. 2. A/c button press and release to change the current setting, the indicator illuminates when a/c is on. Performing this function again will cause the a/c operation to switch into...

  • Page 390

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 391

    The passenger temperature setting with the driver tem- perature setting. Changing the passenger temperature setting while in sync will automatically exit this feature. 10. Blower control blower control is used to regulate the amount of air forced through the climate system. There are seven blower sp...

  • Page 392

    • bi-level mode air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demis- ter outlets. Note: bi-level mode is designed under comfort con- ditions to provide cooler air out of the panel outlets and warmer air from the ...

  • Page 393

    The temperature bar towards the red arrow button on the touchscreen for warmer temperature settings. Note: in sync mode, this button will also automatically adjust the passenger temperature setting at the same time. 15. Temperature control (5.0 radio only) press the temperature button on the touchsc...

  • Page 394

    Max a/c max a/c sets the control for maximum cooling perfor- mance. Press and release to toggle between max a/c and the prior settings. The button on the touchscreen illuminates when max a/c is on. In max a/c, the blower level and mode position can be adjusted to desired user settings. Pressing othe...

  • Page 395

    2. Next, adjust the temperature you would like the system to maintain by adjusting the driver and pas- senger temperature buttons on the faceplate or but- tons on the touchscreen. Once the desired temperature is displayed, the system will achieve and automati- cally maintain that comfort level. 3. W...

  • Page 396

    The operator can also select the direction of the airflow by selecting one of the available mode settings. A/c operation and recirculation control can also be manually selected in manual operation. Note: each of these features operates independently from each other. If any feature is controlled manu...

  • Page 397

    Window fogging interior fogging on the windshield can be quickly re- moved by turning the mode selector to defrost. The defrost/floor mode can be used to maintain a clear windshield and provide sufficient heating. If side win- dow fogging becomes objectionable, increase blower speed to improve airfl...

  • Page 398

    Control setting suggestions for various weather conditions 396 understanding your instrument panel.

  • Page 399

    Uconnect® voice recognition quick tips introducing uconnect® start using uconnect® voice recognition with these help- ful quick tips. It provides the key voice commands and tips you need to know to control your uconnect® 5.0 or 8.4a/8.4an system. Key features: • 5” touchscreen • three buttons on eit...

  • Page 400

    If you see the icon on your touchscreen, you have the uconnect® 8.4an system. If not, you have a uconnect® 8.4a system. Get started all you need to control your uconnect® system with your voice are the buttons on your steering wheel. 1. Visit uconnectphone.Com to check mobile device and feature comp...

  • Page 401

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect® system. Push the vr button . After the beep, say & • cancel to stop a current voice session • help to hear a list of suggested voice commands • repeat to listen to the system prompts again notice...

  • Page 402

    Uconnect® 5.0 uconnect® 8.4a/8.4an 400 understanding your instrument panel.

  • Page 403

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio® stations you would like to hear. (sub- scription or included siriusxm satellite radio® trial required.) push the vr button . After the beep, say & • tune to ninety-five-point-five fm • tune to satellite channel hits 1 tip...

  • Page 404

    Media uconnect® offers connections via usb, sd, bluetooth® and auxiliary ports (if equipped). Voice operation is only available for connected usb and ipod® devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands a...

  • Page 405

    Uconnect® 5.0 media uconnect® 8.4a/8.4an media 4 understanding your instrument panel 403.

  • Page 406

    Phone making and answering hands-free phone calls is easy with uconnect®. When the phonebook button is illumi- nated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Push the phone button . After the beep, say one of the foll...

  • Page 407

    Voice text reply uconnect® will announce incoming text messages. Push the phone button and say listen. (must have com- patible mobile phone paired to uconnect® system.) 1. Once an incoming text message is read to you, push the phone button . After the beep, say: “reply” 2. Listen to the uconnect® pr...

  • Page 408

    Tip: your mobile phone must have the full implementa- tion of the message access profile (map) to take advan- tage of this feature. For details about map, visit uconnectphone.Com. Apple iphone® ios6 or later supports reading incoming text messages only. Climate (8.4a/8.4an) too hot? Too cold? Adjust...

  • Page 409

    Navigation (8.4a/8.4an) the uconnect® navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. (navigation is optional on the uconnect® 8.4a system. See your dealer to activate navigation at any time.) 1. To enter a destination, push...

  • Page 410

    Press the apps button on the 8.4-inch touchscreen to get started. Detailed registration instructions can be found on the next page. *uconnect® access is available only on equipped ve- hicles purchased within the continental united states and alaska. Services can only be used where coverage is availa...

  • Page 411

    5. Click on the link inside the email within 72 hours and complete the easy online registration process to create a personal mopar® owner connect account linked to your vehicle. Mobile app (8.4a/8.4an) securely link your mobile device to your vehicle with the uconnect® access app. Once you have down...

  • Page 412

    Download the uconnect® access app to a compatible apple® or android® mobile devices. All you need to do is: 1. After registering with uconnect® access, log on to your mopar® owner connect account at moparownerconnect.Com 2. On the dashboard page, enter your mobile phone number to receive a link to d...

  • Page 413

    Yelp® (8.4a/8.4an) once registered with uconnect® access, you can use your voice to search for the most popular places or things around you. 1. Press the “apps” button on the touchscreen. 2. Press the “all apps” button on the touchscreen. 3. Press the “yelp” button on the touchscreen. 4. Once the ye...

  • Page 414

    Siriusxm travel link™ (8.4a/8.4an) need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? Siriusxm travel link™ is a suite of services that brings a wealth of information right to your uconnect® 8.4an system. (not available for 8.4a system.) push...

  • Page 415

    Additional information © 2014 chrysler group llc. All rights reserved. Mopar and uconnect are registered trademarks and mopar owner connect is a trademark of chrysler group llc. Android is a trademark of google inc. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. Yelp,...

  • Page 417: Starting And Operating

    Starting and operating contents ! Starting procedures . . . . . . . . . . . . . . . .421 ▫ automatic transmission . . . . . . . . . . . . . . . .421 ▫ keyless enter-n-go™ . . . . . . . . . . . . . . . . . .422 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .422 ▫ extreme cold weather (...

  • Page 418

    ▫ shifting procedures . . . . . . . . . . . . . . . . . . . .443 ▫ quadra-drive® ii system — if equipped . . . . .447 ! Selec-terrain™ — if equipped . . . . . . . .448 ▫ description . . . . . . . . . . . . . . . . . . . . . . . . . .448 ▫ driver information display (did) messages . . .450 ! Quadra-l...

  • Page 419

    ! Brake system . . . . . . . . . . . . . . . . . . . . . . .472 ! Electronic brake control system . . . .473 ▫ anti-lock brake system (abs) . . . . . . . . . . . .473 ▫ traction control system (tcs) . . . . . . . . . . . .475 ▫ brake assist system (bas) . . . . . . . . . . . . . . .475 ▫ electronic ...

  • Page 420

    ▫ radial ply tires . . . . . . . . . . . . . . . . . . . . . .508 ▫ tire types . . . . . . . . . . . . . . . . . . . . . . . . . . .509 ▫ run flat tires — if equipped . . . . . . . . . . . . .511 ▫ spare tires — if equipped . . . . . . . . . . . . . . .511 ▫ tire spinning . . . . . . . . . . . . . ....

  • Page 421

    ▫ carbon monoxide warnings . . . . . . . . . . . . .531 ! Flexible fuel (3.6l engine only) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .532 ▫ e-85 general information . . . . . . . . . . . . . . .532 ▫ ethanol fuel (e-85) . . . . . . . . . . . . . . . . . . . .533 ▫ fuel requir...

  • Page 422

    ! Recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . . . .557 ▫ towing this vehicle behind another vehicle . .557 ▫ recreational towing – two-wheel drive models . . . . . . . . . . . . . . . . . . . . . . . . . . . . .558 ▫ recreational towing – quadra-trac i® (single-speed...

  • Page 423

    Starting procedures before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • when leaving the vehicle, always make sure the ignition is in the off position, remove...

  • Page 424

    Caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • do not shift from reverse, park, or neutral into any forward gear when the engine is above idle speed. • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse...

  • Page 425

    4. If you wish to stop the cranking of the engine prior to the engine starting, push the button again. Note: normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. To turn off the engine using engine start/stop button 1. Place the shift lever...

  • Page 426

    And start. To change the ignition positions without starting the vehicle and use the accessories follow these steps: • starting with the ignition in the off position, • push the engine start/stop button once to place the ignition to the acc position (did will display “acc”), • push the engine start/...

  • Page 427

    Warning! (continued) • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. • if the...

  • Page 428

    After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a groun...

  • Page 429

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 430

    Caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into or out of park or reverse only after the vehicle has come to a complete stop. • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting i...

  • Page 431

    Fuel economy (eco) mode the fuel economy (eco) mode can improve the vehi- cle’s overall fuel economy during normal driving condi- tions. Each time the vehicle is started eco mode is engaged and an amber light in the center stack of the instrument panel will be illuminated. To disable eco mode, push ...

  • Page 432

    • the torque converter clutch may engage at lower engine speeds and remain on longer. • the overall driving performance will be more conser- vative. • vehicles with quadra-lift™ air suspension will oper- ate in # aero # mode over a broader speed range. Refer to # quadra-lift™ # in # starting and ope...

  • Page 433

    The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilomete...

  • Page 434

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 435

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 436

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 437

    • with brake pedal released, look at the transmission gear position display and verify that it indicates the park position (p). Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral (n) use this range when the vehicl...

  • Page 438

    Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through all forward gears. The drive position provides optimum driving characteris- tics under all normal ope...

  • Page 439

    Transmission limp home mode transmission function is monitored electronically for abnormal conditions. If a condition is detected that could result in transmission damage, transmission limp home mode is activated. In this mode, the transmission may operate only in certain gears, or may not shift at ...

  • Page 440

    Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required...

  • Page 441

    • the transmission will automatically downshift as the vehicle slows (to prevent engine lugging) and will display the current gear. • the transmission will automatically downshift to first gear when coming to a stop. After a stop, the driver should manually upshift (+) the transmission as the vehicl...

  • Page 442

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Four-wheel drive operation quadra-trac i® operating instructions/ precautions — if equipped the quadra-trac i® is ...

  • Page 443

    The same speed. The 4wd low position is intended for loose, slippery road surfaces only. Driving in the 4wd low position on dry, hard-surfaced roads may cause increased tire wear and damage to driveline components. When operating your vehicle in 4wd low, the engine speed is approximately three times...

  • Page 444

    Shift positions for additional information on the appropriate use of each 4wd system mode position, see the information below: 4wd auto this range is used on surfaces such as ice, snow, gravel, sand, and dry hard pavement. Note: refer to “selec-terrain® – if equipped” in “start- ing and operating” f...

  • Page 445

    4wd low this range is for low speed four-wheel drive. It provides an additional gear reduction which allows for increased torque to be delivered to both the front and rear wheels while providing maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Note: refer...

  • Page 446

    Note: if shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “for 4x4 low slow below 3 mph (5 km/h) put trans in “n” press 4 low” message will flash from the driver information display (did). Refer to “driver in- formation display (did)” in “u...

  • Page 447

    Shifting into neutral (n) warning! You or others could be injured or killed if you leave the vehicle unattended with the power transfer unit in the neutral (n) position without first fully engaging the parking brake. The neutral (n) position disengages both the front and rear drive shafts from the p...

  • Page 448

    6. After the shift is completed and the neutral (n) light stays on, release the neutral (n) button. 7. Shift the transmission into reverse. 8. Release the brake pedal for five seconds and ensure that there is no vehicle movement. Note: if shift conditions/interlocks are not met, a “to tow vehicle sa...

  • Page 449

    6. Using a ballpoint pen or similar object, push and hold the recessed transfer case “n” button (located by the selector switch) for one second. 7. When the neutral (n) indicator light turns off, release the neutral (n) button. 8. After the neutral (n) button has been released, the transfer case wil...

  • Page 450

    The transfer case and axle coupling differ in design, their operation is similar. Follow the quadra-trac ii® transfer case shifting information, preceding this section, for shifting this system. Selec-terrain™ — if equipped description selec-terrain™ combines the capabilities of the vehicle control ...

  • Page 451

    Launches, to minimize wheel slippage. If equipped with air suspension, the default ride height for snow is nrh. • auto – fully automatic full time four-wheel drive operation can be used on and off road. Balances traction with seamless steering feel to provide im- proved handling and acceleration ove...

  • Page 452

    Note: activate the hill descent control or selec speed control for steep downhill control. See “electronic brake control system” in this section for further information. Driver information display (did) messages when the appropriate conditions exist, a message will appear in the did display. Refer t...

  • Page 453

    • normal ride height (nrh) – this is the standard position of the suspension and is meant for normal driving. • off-road 1 (or1) (raises the vehicle approximately 1.1 in (28 mm) – this is the primary position for all off-road driving until or2 is needed. A smoother and more comfortable ride will res...

  • Page 454

    Speed falls below 20 mph (32 km/h). The vehicle will enter aero mode, regardless of vehicle speed if the shift lever is in the “sport” position. • entry/exit mode (lowers the vehicle approximately 1.6 in (40 mm) – this position lowers the vehicle for easier passenger entry and exit as well as loweri...

  • Page 455

    The system requires that the engine be running for all changes. When lowering the vehicle all of the doors, including the liftgate, must be closed. If a door is opened at any time while the vehicle is lowering the change will not be completed until the open door(s) is closed. The quadra-lift™ air su...

  • Page 456

    Air suspension modes the air suspension system has multiple modes to protect the system in unique situations: tire/jack mode to assist with changing a spare tire, the air suspension system has a feature which allows the automatic leveling to be disabled. Refer to “uconnect® settings” in “under- stan...

  • Page 457

    Driver information display (did) messages when the appropriate conditions exist, a message will appear in the did display. Refer to “driver information display (did)” in “understanding your instrument panel” for further information. Operation the indicator lamps 3 through 6 will illuminate to show t...

  • Page 458

    • off-road 2 (or2) – indicator lamps 4, 5, and 6 will be illuminated when the vehicle is in or2. • off-road 1 (or1) – indicator lamps 4 and 5 will be illuminated when the vehicle is in or1. • normal ride height (nrh) – indicator lamp 4 will be illuminated when the vehicle is in this position. • entr...

  • Page 459

    On-road driving tips utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them a higher center of gravity than ordinary cars. An advantage of the higher ground clearance ...

  • Page 460

    Note: on summit models the lower front fascia is not removable. Lower front fascia removal: 1. Remove the seven quarter turn fasteners. 2. Starting on one side of the vehicle, disengage lower fascia from the upper fascia. Grasp the portion inside the wheel well. Pulling it downwards and toward you, ...

  • Page 461

    Note: it is recommend to also remove the radar sensor on vehicle equipped to adaptive cruise control (acc). This radar sensor is specifically calibrated to your vehicle and is not interchangeable with other radar sensors. Radar sensor removal procedure (if equipped with adaptive cruise control [acc]...

  • Page 462

    Note: only models with the off road package are equipped with the a protective connector. 5. Remove the plug from the protective connector and install on the sensor. 6. Insert the wiring harness connector into the protective connector. 7. Store sensor and bracket in a safe place. Note: all cruise co...

  • Page 463

    3. Return to the center of the vehicle and repeat step 2 to the opposite side of the vehicle. Note: • it may be necessary to apply additional force to individual tabs to make sure they are fully engaged. • do not use any tools to apply additional force to the tabs as damage to the upper and lower fa...

  • Page 464

    Caution! Do not drive in 4wd-low range on dry pavement; driveline damage may result. 4wd-low range locks front and rear drivelines together and does not allow for differential action between the front to rear driveshafts. Driving in 4wd-low on pavement will cause driveline binding; use only on wet o...

  • Page 465

    Entering. Proceed with caution and maintain a steady controlled speed less than 5 mph (8 km/h) in deep water to minimize wave effects. Flowing water if the water is swift flowing and rising (as in storm run-off), avoid crossing until the water level recedes and/or the flow rate is reduced. If you mu...

  • Page 466

    Avoid abrupt downshifts on icy or slippery roads, be- cause engine braking may cause skidding and loss of control. Hill climbing note: before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower ge...

  • Page 467

    Traction downhill when descending mountains or hills, use hill descent or selec-speed control to avoid repeated heavy braking. If not equipped with hill descent or selec-speed control use the following procedure: shift the transmission into a low gear, and the transfer case into 4wd low range. Let t...

  • Page 468

    • after extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. ...

  • Page 469

    If the “service power steering” message and a flashing icon are displayed on the did screen, it indicates that the vehicle needs to be taken to the dealer for service. It is likely the vehicle has lost power steering assistance. Refer to “driver information display (did)” in “understanding your inst...

  • Page 470

    If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these condi- tions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. Note: • increased noise levels at the end of ...

  • Page 471

    Apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an autho- rized dealer. Caution! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the new vehicle ...

  • Page 472

    The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully. To release the parking brake, press the park brake pedal a second time and let your foot up as you feel the brake disengage. When the parki...

  • Page 473

    When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. Apply the parking brake before placing the shift lever in park, otherwise the load on the transmission locking mechanism may make it difficult to move the s...

  • Page 474

    Warning! (continued) • do not leave the key fob in or near the vehicle or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n-go™ in the acc or on/run mode. A child could operate power windows, other controls, or move the vehicle. • be sure ...

  • Page 475

    In the event power assist is lost for any reason (i.E., repeated brake applications with the engine off) the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating. Electronic brake control system your veh...

  • Page 476

    Warning! Significant over or under-inflation of tires, or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. The anti-lock brake system conducts a low speed self- test at about 12 mph (20 km/h). If for any reason your foot is on the brake when the vehicle reach...

  • Page 477

    Caution! The anti-lock brake system is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or tele- phones. Note: during severe braking conditions, a pulsing sen- sation may occur and a clicking noise will be heard. This is normal, ind...

  • Page 478

    Quickly results in the best bas assistance. To receive the benefit of the system, you must apply continuous brak- ing pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the bas is...

  • Page 479

    Warning! Many factors, such as vehicle loading, road condi- tions, and driving conditions, influence the chance that wheel lift or rollover may occur. Erm cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. The capabili...

  • Page 480

    Activation/malfunction indicator light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. Warning! The electronic stability control (esc) cannot pre- vent the natural la...

  • Page 481

    Mode. This mode should be used for most driving situations. Esc should only be turned to “partial off” mode for specific reasons as noted below. Partial off this mode is entered by momentarily pressing the “esc off” switch. When in “partial off” mode, the tcs portion of esc, except for the bld featu...

  • Page 482

    Warning! • when in “partial off” mode, the tcs functionality of esc, (except for the limited slip feature de- scribed in the tcs section), has been disabled and the “esc off indicator light” will be illuminated. When in “partial off” mode, the engine power reduction feature of tcs is disabled, and t...

  • Page 483

    Attempt to stop the trailer from swaying. Tsc is disabled when the esc system is in the “partial off” mode. Warning! If tsc activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Hill start assist (hsa) the hsa system...

  • Page 484

    Warning! There may be situations on minor hills with a loaded vehicle, or while pulling a trailer, when the system will not activate and slight rolling may occur. This could cause a collision with another vehicle or object. Always remember the driver is responsible for brak- ing the vehicle. Towing ...

  • Page 485

    Warning! (continued) • hsa is not a parking brake. If you stop the vehicle on a hill without putting the transmission in park and using the parking brake, it will roll down the hill and could cause a collision with another ve- hicle or object. Always remember to use the park- ing brake while parking...

  • Page 486

    Hill descent control (hdc) — if equipped (four-wheel drive models with mp3023 two-speed transfer case only) hdc is intended for low speed off road driving while in 4wd low range. Hdc maintains vehicle speed while descending hills during various driving situations. Hdc controls vehicle speed by activ...

  • Page 487

    • driver door is closed activating hdc once hdc is enabled it will activate automatically if driven down a grade of sufficient magnitude (greater than approximately 8%). The set speed for hdc is selectable by the driver, and can be adjusted by using the paddle shifter. The following summarizes the h...

  • Page 488

    Driver override: the driver may override hdc activation with throttle or brake application at any time. While in driver override the transmission will be in ers which is a top gear limiter and the vehicle will shift from 1st through the gear that is being displayed. Deactivating hdc hdc will be deac...

  • Page 489

    Feedback to the driver: the instrument cluster has a hdc icon and a hdc switch which has an led which offers feedback to the driver about the state hdc is in. • the cluster icon and switch lamp will illuminate and remain on solid when hdc is enabled or activated. This is the normal operating conditi...

  • Page 490

    Selec speed control (ssc) — if equipped (four-wheel drive models with mp3023 two-speed transfer case only) ssc is intended for off road driving in 4wd low range only. Ssc maintains vehicle speed by actively controlling engine torque and brakes. Ssc has three states: 1. Off (feature is not enabled an...

  • Page 491

    Activating ssc once ssc is enabled it will activate automatically once the following conditions are met: • driver releases throttle • driver releases brake • transmission is in any selection other than p • vehicle speed is below 20 mph (32 km/h) the set speed for ssc is selectable by the driver, and...

  • Page 492

    • ssc performance is influenced by the terrain select mode. This difference may be notable to the driver and may be perceived as a varying level of aggressiveness. Driver override: the driver may override ssc activation with throttle or brake application at any time. While in driver override the tra...

  • Page 493

    Feedback to the driver: the instrument cluster has an ssc icon and the ssc switch has an led which offers feedback to the driver about the state ssc is in. • the cluster icon and switch lamp will illuminate and remain on solid when ssc is enabled or activated. This is the normal operating condition ...

  • Page 494

    Vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected. The “esc activation/malfunction indicator light” (lo- cated in the instrument cluster) starts to flash as soon as ...

  • Page 495

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 496

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 497

    Example: 65, 85, 80 = aspect ratio in percent (%) – ratio of section height to section width of tire, or 10.5 = section width in inches (in) r = construction code – # r # means radial construction, or – # d # means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service descri...

  • Page 498

    Example: h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.E., tire press...

  • Page 499

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 500

    Example: dot ma l9 abcd 0301 01 = number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represen...

  • Page 501

    Term definition maximum inflation pressure the maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Recommended cold tire inflation pres- sure vehicle manufacturer’s recommended cold tire inflati...

  • Page 502

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) 500 starting and operating.

  • Page 503

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. Example tire placard location (b-pillar) tire and loading information placard 5 starting and operating 501.

  • Page 504

    3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to t...

  • Page 505

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 506

    504 starting and operating.

  • Page 507

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 508

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 509

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Cau...

  • Page 510

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits ...

  • Page 511

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than ¼ # (6 mm). Consult an authorize...

  • Page 512

    Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Warning! Do not use summer tires in snow/ice conditions. You could lose vehi...

  • Page 513

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Run flat tires — if equipped run flat tires a...

  • Page 514

    Equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact spare tire — if equipped the compact spa...

  • Page 515

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the ...

  • Page 516

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 517

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16” (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further infor- mation. Life of tir...

  • Page 518

    Wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed. Refer to the paragraph on “tread wear indicator.” refer to the tire and loading information placard or ...

  • Page 519

    Warning! (continued) • never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • failure to equip your vehicle wi...

  • Page 520

    Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device clearance be- tween tires and other suspension components, it is important that only traction devices in good condi- tion are used. Broken devices can cause serious damage. S...

  • Page 521

    Type tires. Rotation will increase tread life, help to main- tain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Refer to the “maintenance schedule” for the proper maintenance intervals. More frequent rotation is permis- sible if desired. The reasons for any rapid or unu...

  • Page 522

    Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold tire placard pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12°f (6.5°c). This means that when the...

  • Page 523

    For example, your vehicle has a recommended cold (parked for more than three hours) tire placard pressure of 33 psi (227 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressure is 28 psi (193 kpa), a temperature drop to 20°f (-7°c) will decrease the tire pressure to approximat...

  • Page 524

    Caution! (continued) • after inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the tire pressure moni- toring sensor. Note: • the tpms is not intended to replace normal tire care and ma...

  • Page 525

    Monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is particularly important, for you to regularly check the tire pressure in all of your tires and to maintain the proper pressure. The tire pressure...

  • Page 526

    Value(s) with the low tire(s) displayed in a different color. Refer to “driver information display (did)” in “under- standing your instrument panel” for further information. Note: your system can be set to display pressure units in psi, bar or kpa. Should a low tire condition occur on any of the fou...

  • Page 527

    Service tpm system warning the tire pressure monitoring telltale light will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime. The did will display a “service tpm sys- tem” message for a minimum of five seconds. This messag...

  • Page 528

    However, the system still needs to be serviced as long as the # service tpm system # message exists. Note: there is no tire pressure monitoring sensor in the spare tire. The tpms will not be able to monitor the tire pressure. If you install the spare tire in place of a road tire that has a pressure ...

  • Page 529

    • this device must accept any interference received, including interference that may cause undesired op- eration. The tpm sensors are regulated under one of the follow- ing licenses: united states mrxmerctx1 canada 2546a-merctx1 fuel requirements 3.6l engine — if equipped this engine is designed to ...

  • Page 530

    As hard starting, stalling, and hesitations. If you experi- ence these symptoms, try another brand of gasoline before considering service for the vehicle. Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) which defin...

  • Page 531

    Problems that result from using gasoline containing methanol or gasoline containing more than 10% ethanol are not the responsibility of the manufacturer and may not be covered under new vehicle limited warranty. E-85 usage in non-flex fuel vehicles non-flex fuel vehicles (ffv) are compatible with ga...

  • Page 532

    Without mmt be used in your vehicle. The mmt content of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether the gasoline contains mmt. Mmt is prohibited in federal and california reformulated gasoline. Materials added to fuel all gasoline sold...

  • Page 533

    Caution! (continued) • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle perfor- mance problems resulting from the use of such fuels or additives is not the respon...

  • Page 534

    Warning! (continued) • guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Flexible fuel (3.6l engine only) — if equipped e...

  • Page 535

    Ethanol fuel (e-85) e-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Warning! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap)...

  • Page 536

    When you do switch fuel types it is recommended that: • you do not add less than 5 gallons (19 liters) when refueling. • you drive the vehicle immediately after refueling for at least 5 miles (8 km). Observing these precautions will avoid possible hard starting and/or significant deterioration in dr...

  • Page 537

    Starting the characteristics of e-85 fuel make it unsuitable for use when ambient temperatures fall below 0°f (-18°c). In the range of 0°f (-18°c) to 32°f (0°c), you may experience an increase in the time it takes for your engine to start, and a deterioration in driveability (sags and/or hesitations...

  • Page 538

    Adding fuel 1. Press the fuel filler door release switch (located under the headlamp switch). 2. Open the fuel filler door. Note: in certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel doo...

  • Page 539

    3. There is no fuel filler cap. A flapper door inside the pipe seals the system. 4. Insert the fuel nozzle fully into the filler pipe, the nozzle opens and holds the flapper door while refuel- ing. 5. Fill the vehicle with fuel, when the fuel nozzle “clicks” or shuts off the fuel tank is full. 6. Wa...

  • Page 540

    Warning! • never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled. • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the “malfunction indicator light” to turn on. • ...

  • Page 541

    Note: if the fuel door does not latch after the manual release cable has been activated, the actuator latch should be manually returned to the closed position. Vehicle loading certification label as required by national highway traffic safety admin- istration regulations, your vehicle has a certific...

  • Page 542

    Rear axle systems (gawr). Total load must be limited so gvwr and front and rear gawr are not exceeded. Payload the payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo. Gross axle weight rating (gawr) th...

  • Page 543

    Values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added. Loading the actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. The entire...

  • Page 544

    Trailer towing in this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain the new vehicle limited war...

  • Page 545

    Warning! (continued) you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision. Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Gross axle weight rating (gawr) the ga...

  • Page 546

    Trailer sway control the trailer sway control can be a mechanical telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable fric- tion associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveli...

  • Page 547

    Warning! • an improperly adjusted weight distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recr...

  • Page 548

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain: engine model frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l 4x2 55 sq ft (5.11 sq m) 6,200 lbs (2 812 kg) 620 ...

  • Page 549

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to “tire safety information” in “starting and operating” for further information. The addition of...

  • Page 550

    2. Pull the bottom of the cover outward (towards you), pull downwards to disengage the tabs located at the top of the hitch receiver cover. To reinstall the hitch receiver cover after towing repeat the procedure in reverse order. Note: be sure to engage all tabs of the hitch receiver cover in the bu...

  • Page 551

    Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer • the weight of any other type of cargo or equipment put in or on your vehicle • the weight of the driver and all passengers note: remember that everything put into or on the tr...

  • Page 552

    Caution! (continued) • then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. This helps the engine and other parts of the vehicle wear in at the heavier loads. Perform the maintenance listed in the “maintenance ...

  • Page 553

    Warning! (continued) • vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle transmission in park. For four-wheel drive vehicles, make sure the transfer case is not in neutral. Always, block or ' chock ' the trailer whee...

  • Page 554

    Tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s gvwr and gawr limits. Towing requirements — trailer brakes warning! • do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause i...

  • Page 555

    • trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 1,653 lbs (750 kg). Towing requirements — trailer lights and wiring whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for mo...

  • Page 556

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy traffic. Automatic transmission the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. However, ...

  • Page 557

    Paddle shift mode • when using the paddle shift switches, select the highest gear that allows for adequate performance and avoids frequent downshifts. For example, choose “5” if the desired speed can be maintained. Choose “4” or “3” if needed to maintain the desired speed. • to prevent excess heat g...

  • Page 558

    Snow plow snow plows, winches, and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structure. The airbags could deploy unexpect- edly or could fail to deploy during a collision. Warning! Do not ...

  • Page 559

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground two-wheel drive models four-wheel drive models without 4–lo range four-wheel drive models with 4–lo range flat tow none not allowed not allowed see instructions • transmissi...

  • Page 560

    Note: • when recreationally towing your vehicle, always fol- low applicable state and provincial laws. Contact state and provincial highway safety offices for additional details. • vehicles equipped with quadra-lift™ must be placed in transport mode before tying them down (from the body) on a traile...

  • Page 561

    6. Install a suitable clamping device, designed for tow- ing, to secure the front wheels in the straight position. Caution! Towing with the rear wheels on the ground will cause severe transmission damage. Damage from improper towing is not covered under the new vehicle limited warranty. Recreational...

  • Page 562

    Caution! • do not dolly tow any 4wd vehicle. Towing with only one set of wheels on the ground (front or rear) will cause severe transmission and/or transfer case damage. Tow with all four wheels either on the ground, or off the ground (using a vehicle trailer). • tow only in a forward direction. Tow...

  • Page 563

    Warning! (continued) position disengages both the front and rear drive- shafts from the powertrain and will allow the vehicle to roll, even if the transmission is in park. The parking brake should always be applied when the driver is not in the vehicle. Use the following procedure to prepare your ve...

  • Page 564

    6. After the shift is completed and the neutral (n) light stays on, release the neutral (n) button. 7. Shift the transmission into reverse. 8. Release the brake pedal for five seconds and ensure that there is no vehicle movement. 9. Shift the transmission back into neutral. 10. With the transmission...

  • Page 565

    Note: • steps 1 through 4 are requirements that must be met before pressing the neutral (n) button, and must continue to be met until the shift has been completed. If any of these requirements are not met before press- ing the neutral (n) button or are no longer met during the shift, then the neutra...

  • Page 566

    6. Using a ballpoint pen or similar object, press and hold the recessed transfer case neutral (n) button (lo- cated by the selector switch) for one second. 7. When the neutral (n) indicator light turns off, release the neutral (n) button. After the neu- tral (n) button has been released, the transfe...

  • Page 567

    Note: • steps 1 through 5 are requirements that must be met before pressing the neutral (n) button, and must continue to be met until the shift has been completed. If any of these requirements are not met before press- ing the neutral (n) button or are no longer met during the shift, the neutral (n)...

  • Page 569: Contents

    What to do in emergencies contents ! Hazard warning flashers . . . . . . . . . . .568 ! If your engine overheats . . . . . . . . . . . .568 ! Wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .569 ▫ torque specifications . . . . . . . . . . . . . . . . . . .570 ! Jacking...

  • Page 570

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank just above the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency...

  • Page 571

    • you can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. Caution! Driving with a hot cooling system could damage ...

  • Page 572

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/ bolt socket size 130 ft-lbs (176 n·m) m14 x 1.50 22 mm **use only chrysler recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the tire and remov...

  • Page 573

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to...

  • Page 574

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack location the scissor-type jack and tire changin...

  • Page 575

    Note: the funnel for the cap-less fuel system is located on top of the spare tire. If your vehicle is out of fuel and an auxiliary fuel can is needed, insert the funnel into the filler neck and proceed to fill the vehicle. For vehicles not equipped with a spare tire, the fuel filler funnel is stored...

  • Page 576

    1. Park the vehicle on a firm, level surface. Avoid ice or slippery surfaces. Warning! Do not attempt to change a tire on the side of the vehicle closest to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Turn on the hazard warning fl...

  • Page 577

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • chock the ...

  • Page 578

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare tire, jack, and tools from storage. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left, one turn, while the whee...

  • Page 579

    4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do not raise the vehicle until you are sure the jack is fully engaged. Jacking locations lift point symbol on sill molding 6 what to do in emergen...

  • Page 580

    5. For a rear tire, place the jack in the slot on the rear tie-down bracket, just forward of the rear tire (as indicated by the triangular lift point symbol on the sill molding). Do not raise the vehicle until you are sure the jack is fully engaged. Front jacking location lift point symbol on sill m...

  • Page 581

    6. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum sta- bility. Warning! Raising the vehicle higher than necessary can make the vehicle ...

  • Page 582

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 9. Lower the vehicle by turning the jack screw counter- clockwise, and remove the jack and wheel blocks....

  • Page 583

    13. Have the aluminum road wheel and tire repaired as soon as possible, properly secure the spare tire with the special wing nut torqued to 3.7 ft-lbs (5 n·m), reinstall the jack and tool kit foam tray, and latch the rear load floor cover. Warning! A loose tire or jack thrown forward in a collision ...

  • Page 584

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Refer to torque table...

  • Page 585

    Note: when using a portable battery booster pack follow the manufacturer’s operating instructions and precautions. Preparations for jump-start the battery in your vehicle is located under the passen- ger’s front seat. There are remote locations located under the hood to assist in jump-starting. Remo...

  • Page 586

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 587

    Jump-starting procedure warning! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Not...

  • Page 588

    5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the...

  • Page 589

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse while gently pressing the accelerator. Note:...

  • Page 590

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 591

    Warning! • do not use a chain for freeing a stuck vehicle. Chains may break, causing serious injury or death. • stand clear of vehicles when pulling with tow hooks. Tow straps may become disengaged, caus- ing serious injury. Caution! Tow hooks are for emergency use only, to rescue a vehicle stranded...

  • Page 592

    2. Open the center console and locate the manual park release cover, remove it by snapping the cover away from the console hinges. 3. Using a screwdriver or similar tool, push the metal latch in towards the tether strap. Manual park release cover release latch 590 what to do in emergencies.

  • Page 593

    4. While the metal latch is in the open position, simulta- neously pull upwards on the tether strap until the lever clicks and latches in the released position. The transmission is now out of park and the vehicle can be moved. Caution! Closing the armrest while the manual park release is activated m...

  • Page 594

    To disengage the manual park release lever: 1. To disengage the manual park release apply tension upward while pushing the release latch towards the tether to unlock the lever. 2. Once the tension has been released and the lever has been unlocked be sure it is stowed properly and locks into position...

  • Page 595

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. If the trans- mission and drivetrain are operable, disabled vehicles may also be towed as described under “recreational towing” in the “starting and operating” section. Note: ...

  • Page 596

    Towing condition wheels off the ground 2wd models 4wd models flat tow none if transmission is operable: • transmission in neutral • 30 mph (48 km/h) max speed • 30 miles (48 km) max distance see instructions in “recreational towing” under “starting and operating” • transmission in park • transfer ca...

  • Page 597

    If the key fob is unavailable, or the vehicle’s battery is discharged, refer to “manual park release” in this section for instructions on shifting the transmission out of park for towing. Caution! • do not use sling type equipment when towing. Vehicle damage may occur. • when securing the vehicle to...

  • Page 598

    Caution! Towing faster than 30 mph (48 km/h) or farther than 30 miles (48 km) with rear wheels on the ground can cause severe transmission damage. Damage from improper towing is not covered under the new vehicle limited warranty. Caution! • towing this vehicle in violation of the above re- quirement...

  • Page 599

    Caution! • front or rear wheel lifts must not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when towing. • towing this vehicle in violation of the above re- quirements can cause severe transmission and/or transfer case damage. Damage f...

  • Page 601: Maintaining Your Vehicle

    Maintaining your vehicle contents ! Engine compartment — 3.6l . . . . . . . . . .601 ! Engine compartment — 5.7l . . . . . . . . . .602 ! Onboard diagnostic system (obd ii) . . .603 ! Emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . . .603 ! Replacement p...

  • Page 602

    ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . .640 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . .641 ▫ automatic transmission . . . . . . . . . . . . . . . .642 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .644 ! Fus...

  • Page 603

    Engine compartment — 3.6l 1 — power distribution center (fuses) 6 — air cleaner filter 2 — engine oil dipstick 7 — washer fluid reservoir 3 — engine oil fill 8 — coolant pressure cap (radiator) 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — power steering fluid reservoir 7 maintaining yo...

  • Page 604

    Engine compartment — 5.7l 1 — power distribution center 5 — washer fluid reservoir 2 — engine oil fill 6 — engine oil dipstick 3 — brake fluid reservoir 7 — coolant pressure cap (radiator) 4 — air cleaner filter 8 — engine coolant reservoir 602 maintaining your vehicle.

  • Page 605

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 606

    Indicator light (mil)” is functioning and is not on when the engine is running, and that the obd ii system is ready for testing. Normally, the obd ii system will be ready. The obd ii system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replace- ment...

  • Page 607

    You may need to do nothing more than drive your vehicle as you normally would in order for your obd ii system to update. A recheck with the above test routine may then indicate that the system is now ready . Regardless of whether your vehicle’s obd ii system is ready or not, if the mil is illuminate...

  • Page 608

    Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. Maintenance procedures the pages tha...

  • Page 609

    Engine oil checking oil level to assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed up en...

  • Page 610

    American petroleum institute (api) engine oil identification symbol this symbol means that the oil has been certified by the american petroleum institute (api). The manufacturer only recommends api certified engine oils. Caution! Do not use chemical flushes in your engine oil as the chemicals can da...

  • Page 611

    Note: mopar® sae 5w-30 engine oil approved to chrysler material standard ms-6395 such as pennzoil®, shell helix® or equivalent may be used when sae 5w-20 engine oil meeting ms-6395 is not available. Engine oil viscosity — 5.7l engine mopar® sae 5w-20 engine oil or equivalent such as pennzoil® or she...

  • Page 612

    Materials added to engine oil the manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental addi- tives. Disposing of used engine oil and oil fil...

  • Page 613

    Warning! (continued) for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury. Engine air cleaner filter selection the quality o...

  • Page 614

    2. Lift the air cleaner cover to access the air cleaner filter. 3. Remove the air cleaner filter element from the housing assembly. Open air cleaner filter assembly 1 — air cleaner cover 2 — air cleaner filter air cleaner filter 1 — air cleaner filter 2 — air cleaner filter inspection surface 612 ma...

  • Page 615

    Engine air cleaner filter installation note: inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air cleaner filter element into the housing assembly with the air cleaner filter inspection surface facing downward. 2. Install the air clea...

  • Page 616

    When inspecting accessory drive belts, small cracks that run across ribbed surface of belt from rib to rib, are considered normal. These are not a reason to replace belt. However, cracks running along a rib (not across) are not normal. Any belt with cracks running along a rib must be replaced. Also ...

  • Page 617

    Belt replacement on some models requires the use of special tools, we recommend having your vehicle ser- viced at an authorized dealer. Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning...

  • Page 618

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 619

    Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Refrigerant recovery and recycling r134a — if equipped r-134a air conditioning refrigerant is a hydrofl...

  • Page 620

    Warning! • do not remove the a/c air filter while the ignition is in the on/run position or personal injury may result. • do not remove the a/c air filter while the blower is operating or personal injury may result. The a/c air filter is located in the fresh air inlet behind the glove compartment. P...

  • Page 621

    2. There are glove compartment travel stops on both sides of the glove compartment door, partially close the glove compartment door and push inward to release the glove compartment travel stop on one side and repeat this procedure for the opposite side. 3. Pull the right hand side of the glove compa...

  • Page 622

    5. Remove the filter cover by disengaging the retaining tab and mid way snap that secures the filter cover to the hvac housing. Disengage the mid way snap by pulling the door outward. Unhinge the filter cover on the right side to fully remove the cover. A/c air filter cover 1 — retaining tab 2 — mid...

  • Page 623

    6. Remove the a/c air filter by pulling it straight out of the housing. 7. Install the a/c air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. Caution! The a/c air filter is identified with an arrow...

  • Page 624

    The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant, such as mopar® lock cylinder lubricant directly into the lock cylinder. Windshield wiper blades clean the rubber edges of the wiper blades and the winds...

  • Page 625

    Front wiper blade removal/installation caution! Do not allow the wiper arm to spring back against the glass without the wiper blade in place or the glass may be damaged. 1. Lift the wiper arm to raise the wiper blade off of the glass, until the wiper arm is in the full up position. Wiper blade with ...

  • Page 626

    2. To disengage the wiper blade from the wiper arm, flip up the release tab on the wiper blade and while holding the wiper arm with one hand, slide the wiper blade down towards the base of the wiper arm. Wiper blade with release tab in unlocked position 1 — wiper blade 2 — release tab 3 — wiper arm ...

  • Page 627

    3. With the wiper blade disengaged, remove the wiper blade from the wiper arm by holding the wiper arm with one hand and separating the wiper blade from the wiper arm with the other hand (move the wiper blade toward the right side of the vehicle to separate the wiper blade from the wiper arm). Wiper...

  • Page 628

    4. Gently lower the wiper arm onto the glass. Installing the front wipers 1. Lift the wiper arm off of the glass, until the wiper arm is in the full up position. 2. Position the wiper blade near the hook on the tip of the wiper arm with the wiper release tab open and the blade side of the wiper faci...

  • Page 629

    2. Lift the rear wiper arm fully off the glass. Wiper pivot cap in unlocked position 1 — wiper arm pivot cap 2 — wiper arm wiper blade in folded out position 1 — wiper arm pivot cap 2 — wiper arm 3 — wiper blade 7 maintaining your vehicle 627.

  • Page 630

    3. To remove the wiper blade from the wiper arm, grasp the bottom end of the wiper blade nearest to wiper arm with your right hand. With your left hand hold the wiper arm as you pull the wiper blade away from the wiper arm past its stop far enough to unsnap the wiper blade pivot pin from the recepta...

  • Page 631

    5. Gently lower the tip of the wiper arm onto the glass. Installing the rear wiper 1. Lift the rear wiper arm pivot cap away from the glass to allow the rear wiper blade to be raised off of the glass. Note: the rear wiper arm cannot be fully raised off the glass unless the wiper arm pivot cap is uns...

  • Page 632

    In cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exer...

  • Page 633

    Warning! (continued) • a hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your ve- hicle in areas where your exhaust system can con- tact anything that can burn. ...

  • Page 634

    Note: intentional tampering with emissions control systems can result in civil penalties being assessed against you. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn ...

  • Page 635

    System should be drained, flushed, and refilled with fresh oat coolant (conforming to ms-12106) by an authorized dealer. Check the front of the a/c condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condens...

  • Page 636

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 637

    Important that you use the same engine coolant (oat coolant conforming to ms-12106) throughout the life of your vehicle. Please review these recommendations for using organic additive technology (oat) engine coolant (antifreeze) that meets the requirements of chrysler material stan- dard ms-12106. W...

  • Page 638

    • mixing engine coolant (antifreeze) types is not recom- mended and can result in cooling system damage. If hoat and oat coolant are mixed in an emergency, have a authorized dealer drain, flush, and refill with oat coolant (conforming to ms-12106) as soon as possible. Cooling system pressure cap the...

  • Page 639

    Engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. Coolant level the coolant bottle provides a quick visual method for determining that the coolant level is ad...

  • Page 640

    • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (antifreeze) needs to be added, the contents of the coolant expansion bottle must also be protected against freezing. • if frequent engine coolant (antifreeze) additions are required, the cooling ...

  • Page 641

    Warning! (continued) high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency. Fluid level check — brake master cylinder the fluid level of the master cylinder should be checked when performing under the hood service, or...

  • Page 642

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 643

    The front axle fill and drain plugs should be tightened to 22 to 29 ft lbs (30 to 40 n·m). Caution! Do not overtighten the plugs as it could damage them and cause them to leak. Rear axle fluid level check the rear axle oil level needs to be no lower than 1/8 in (3 mm) below the bottom of the fill ho...

  • Page 644

    Drain first remove fill plug, then remove drain plug. Recom- mended tightening torque for drain and fill plugs is 15 to 25 ft lbs (20 to 34 n·m). Caution! When installing plugs, do not overtighten. You could damage them and cause them to leak. Selection of lubricant use only the manufacturer’s recom...

  • Page 645

    Special additives the manufacturer strongly recommends against using any special additives in the transmission. Automatic transmission fluid (atf) is an engineered product and its performance may be impaired by supple- mental additives. Therefore, do not add any fluid addi- tives to the transmission...

  • Page 646

    Fluid and filter changes under normal operating conditions, the fluid installed at the factory will provide satisfactory lubrication for the life of the vehicle. Routine fluid and filter changes are not required. How- ever, change the fluid and filter if the fluid becomes contaminated (with water, e...

  • Page 647

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar® car wash, or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover...

  • Page 648

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as...

  • Page 649

    Caution! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s pro- tective finish. Only mopar® whee...

  • Page 650

    Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar® total clean. ...

  • Page 651

    Glass surfaces all glass surfaces should be cleaned on a regular basis with mopar® glass cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear quarter window ...

  • Page 652

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 653

    Warning! (continued) • if a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Power distribution center the power distribution center is located in the engine compart...

  • Page 654

    Cavity cartridge fuse micro fuse description f03 60 amp yellow – radiator fan f05 40 amp green – compressor for air suspension - if equipped f06 40 amp green – anti-lock brakes/electronic stability con- trol pump f07 40 amp green – starter solenoid f08 20 amp blue – emission sensors (diesel engine o...

  • Page 655

    Cavity cartridge fuse micro fuse description f20 30 amp pink – passenger door module f22 20 amp blue – engine control module f23 30 amp pink – interior lights #1 f24 30 amp pink – driver door module f25 30 amp pink – front wipers f26 30 amp pink – anti-lock brakes/stability control module/valves f28...

  • Page 656

    Cavity cartridge fuse micro fuse description f38 30 amp pink – power inverter 115v ac - if equipped f39 30 amp pink – power liftgate - if equipped f40 – 10 amp red daytime running lights f42 – 20 amp yellow horn f44 – 10 amp red diagnostic port f46 – 10 amp red tire pressure monitor - if equipped f4...

  • Page 657

    Cavity cartridge fuse micro fuse description f56 – 15 amp blue additional content (diesel engine only) f57 – 15 amp blue hid headlamps lh - if equipped f59 – 10 amp red purging pump (diesel engine only) f60 – 15 amp blue transmission control module f61 – 10 amp red transmission control module/pm sen...

  • Page 658

    Cavity cartridge fuse micro fuse description f70 – 20 amp yellow fuel pump motor f71 – 30 amp green audio amplifier f73 – 15 amp blue hid headlamp rh - if equipped f74 – 20 amp yellow brake vacuum pump - if equipped f76 – 10 amp red anti-lock brakes/electronic stability control f77 – 10 amp red driv...

  • Page 659

    Cavity cartridge fuse micro fuse description f83 – 10 amp red fuel door f84 – 15 amp blue switch bank/instrument cluster f85 – 10 amp red airbag module f86 – 10 amp red airbag module f87 – 10 amp red air suspension – if equipped / trailer tow / steering column control module f88 – 15 amp blue instru...

  • Page 660

    Cavity cartridge fuse micro fuse description f97 – 20 amp yellow rear heated seats & heated steering wheel - if equipped f98 – 20 amp yellow front heated seats - if equipped f99 – 10 amp red climate control / driver assistance systems module f100 – 10 amp red active damping - if equipped f101 – 15 a...

  • Page 661

    Caution! • when installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • when replacing a blown fuse,...

  • Page 662

    Replacement bulbs interior bulbs bulb number glove box lamp 194 grab handle lamp l002825w5w overhead console reading lamps vt4976 rear cargo lamp 214–2 visor vanity lamp v26377 underpanel courtesy lamps 906 instrument cluster (general illumination) 103 telltale/hazard lamp 74 exterior bulbs bulb num...

  • Page 663

    Bulb number headlamps (high beam) - if equipped 9005 premium park/turn signal lamp led - (service at authorized dealer) premium daytime running lamp (drl) led - (service at authorized dealer) front fog lamps h11 front side marker - if equipped w5w premium front side marker - if equipped led - (servi...

  • Page 664

    Bulb number rear body side tail lamps led - (service at authorized dealer) chmsl - center high mounted stop lamp led - (service at authorized dealer) note: numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your authorized ...

  • Page 665

    Warning! A transient high voltage occurs at the bulb sockets of high intensity discharge (hid) headlamps when the headlamp switch is turned on. It may cause serious electrical shock or electrocution if not serviced prop- erly. See your authorized dealer for service. Note: on vehicles equipped with h...

  • Page 666

    Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front fog lamps 1. Reach through the cutout in the splash shield and disconnect the wiring harness from th...

  • Page 667

    6. Firmly and evenly push the bulb straight into the lamp housing until both tabs snap firmly into place and are fully engaged. 7. Connect the wiring harness to the front fog lamp connector. Rear tail, stop, and turn signal lamps 1. Raise the liftgate. 2. Remove the two push-pins from the tail lamp ...

  • Page 668

    4. Twist socket counter clockwise and remove from lamp. 5. Pull the bulb to remove it from the socket. 6. Replace the bulb, reinstall the socket, and reattach the lamp assembly. Rear liftgate mounted tail lamp 1. Raise the liftgate. 2. Use a fiber stick or flat blade screw driver to pry the lower tr...

  • Page 669

    5. Tail lamps are now visible. Rotate socket(s) counter clockwise. 6. Remove/replace bulb(s). 7. Reinstall the socket(s) 8. Reverse process to reinstall the liftgate trim. Rear liftgate tail lamps 1 — auxiliary led tail connector – do not remove 2 — backup bulb socket 7 maintaining your vehicle 667.

  • Page 670

    Center high-mounted stop lamp (chmsl) the center high mounted stop lamp is led. Service at authorized dealer. Rear license lamp 1. The rear license lamps are led. Service at authorized dealer center high-mounted stop lamp 668 maintaining your vehicle.

  • Page 671

    Fluid capacities u.S. Metric fuel (approximate) 3.6l and 5.7l engines 25 gallons 94 liters engine oil with filter 3.6l engine (sae 5w-20, api certified) 6 quarts 5.6 liters 5.7l engine (sae 5w-20, api certified) 7 quarts 6.6 liters cooling system* 3.6l engine (mopar® antifreeze/engine coolant 10 yea...

  • Page 672

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology). Engine oil – 3.6l engine we recommend you use api certified sae 5w-20 engine oil, meet...

  • Page 673

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 674

    Chassis component fluid, lubricant, or genuine part automatic transmission use only mopar® zf 8&9 speed atf™ automatic transmission fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Transfer case – single-speed (quadra-trac i®) we reco...

  • Page 675

    Component fluid, lubricant, or genuine part brake master cylinder we recommend you use mopar® dot 3 brake fluid, sae j1703 should be used. If dot 3, sae j1703 brake fluid is not available, then dot 4 is acceptable. Power steering reservoir – 3.6l engine we recommend you use mopar® hydraulic fluid. P...

  • Page 677: Maintenance Schedules

    Maintenance schedules contents ! Maintenance schedule . . . . . . . . . . . . .676 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .678 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 678

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 679

    Required maintenance refer to the maintenance schedules on the following pages for required maintenance. At every oil change interval as indicated by oil change indicator system: • change oil and filter. • rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil...

  • Page 680

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,0...

  • Page 681

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 682

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 683

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 685: Contents

    If you need consumer assistance contents ! Suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .685 ▫ prepare for the appointment. . . . . . . . . . . . .685 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .685 ▫ be reasonable with requests ....

  • Page 686

    ! Department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .691 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .691 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .691 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .692 684 if...

  • Page 687

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 688

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 689

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 690

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 691

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 692

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 693

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 694

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 695: Index

    Index 10

  • Page 696

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . .472 abs (anti-lock brake system) . . . . . . . . . . . . . . . .473 adaptive cruise control (acc) (cruise control) . . .192 adding engine coolant (antifreeze) . . . . . . . . . . . .634 adding fuel . . . . . . . . . . . . . . . . . . ....

  • Page 697

    Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .636 anti-lock warning light . . . . . . . . . . . . . . . . . . . .292 appearance care . . . . . . . . . . . . . . . . . . . . . . . . .644 assist, hill start . . . . . . . . . . . . . . . . . . . . . . . . . .481 auto down power wi...

  • Page 698

    Bulbs, light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 camera, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . .243 capacities, fluid . . . . . . . . . . . . . . . . . . . . . . . . . .669 caps, filler oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .60...

  • Page 699

    Child safety locks . . . . . . . . . . . . . . . . . . . . . . . . .34 clean air gasoline . . . . . . . . . . . . . . . . . . . . . . . .528 cleaning wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .646 climate control . . . . . . . . . . . . . . . . . . . . . . . . . .385 automat...

  • Page 700

    Door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 child-protection door lock — rear doors . . . . . .34 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 door locks, automatic . . . . . . . . . . . . . . . . . . . . . .33 door opener, garage. . . . . . . . ....

  • Page 701

    Fails to start . . . . . . . . . . . . . . . . . . . . . . . . . . .424 flooded, starting . . . . . . . . . . . . . . . . . . . . . . .424 fuel requirements . . . . . . . . . . . . . . . . . . . . . .527 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .582 oil . . . . . . . . . . . ....

  • Page 702

    Fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . . .669 fluid leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 fluid level checks automatic transmission . . . . . . . . . . . . . . . . . .643 brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .639 e...

  • Page 703

    Gasoline (fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . .527 gasoline, reformulated . . . . . . . . . . . . . . . . . . . . .528 gauges coolant temperature . . . . . . . . . . . . . . . . . . . . .294 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 speedometer ....

  • Page 704

    Instrument panel lens cleaning . . . . . . . . . . . . . . .649 interior appearance care. . . . . . . . . . . . . . . . . . . .647 intermittent wipers (delay wipers). . . . . . . . . . . . .180 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 inverter, power . . . . . . . . ...

  • Page 705

    Leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .515 liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 liftgate window wiper/washer . . . . . . . . . . . . . . .282 light bulbs....

  • Page 706

    Turn signal . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 vanity mirror . . . . . . . . . . . . . . . . . . . . . . . . . .134 loading vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .539 tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500 locks . . . . . ...

  • Page 707

    Octane rating, gasoline (fuel) . . . . . . . . . . . . . . . .527 odometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .298 trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .298 off-pavement driving (off-road) . . . . . . . . . . . . . .457 off-road driving (off-pa...

  • Page 708

    Door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .269 lift gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 outlet (auxiliar...

  • Page 709

    Shifting into transfer case neutral (n) . . . . . . . .560 shifting out of transfer case neutral (n) . . . . . .446 reformulated gasoline . . . . . . . . . . . . . . . . . . . . .528 refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .617 reminder, seat belt. . . . . . . . . . . ....

  • Page 710

    Beltalert® . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 disengage the automatic locking mode . . . . . . .63 energy management feature . . . . . . . . . . . . . . . .61 engage the automatic locking mode . . . . . . . . .62 lap/shoulder belt operation . . . . . . . . . . . . . . . .56 ...

  • Page 711

    Sentry key® fcc general information . . . . . . . . . . . . . . . . . .18 key programming . . . . . . . . . . . . . . . . . . . . . . .18 sentry key (immobilizer) . . . . . . . . . . . . . . . . . . . .16 sentry key replacement . . . . . . . . . . . . . . . . . . . . .17 service assistance . . . . ....

  • Page 712

    Sunglasses storage . . . . . . . . . . . . . . . . . . . . . . . .247 sun roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257 sun visor extension . . . . . . . . . . . . . . . . . . . . . . .134 supplemental restraint system - airbag . . . . . . . . . .68 suspension, air. . . . . ....

  • Page 713

    Trailer towing . . . . . . . . . . . . . . . . . . . . . . . . .551 tread wear indicators . . . . . . . . . . . . . . . . . . . .514 tire safety information . . . . . . . . . . . . . . . . . . . . .493 tongue weight/trailer weight . . . . . . . . . . . . . . . .548 tow hooks, emergency . . . . . . ....

  • Page 714

    Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .359 screen activated features . . . . . . . . . . . . . . . . . .23 uconnect® settings . . . . . . . . . . . . . . . . . . . . . . .24 uconnect® settings. . . . . . . . . . . . . . . . . . . . . . . . .23 customer programmable featur...

  • Page 715

    Windshield wipers . . . . . . . . . . . . . . . . . . . . . . . .178 wiper blade replacement . . . . . . . . . . . . . . . . . . .622 wipers, intermittent . . . . . . . . . . . . . . . . . . . . . . .180 wipers, rain sensitive . . . . . . . . . . . . . . . . . . . . . .182 10 index 713.

  • Page 716

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed prop- erly by trained personnel. The following must be obs...

  • Page 717

    Grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2015 gr and cher ok ee 15wk741-126-aa first edition printed in u.S.A. 2 0 1 5.