1. DL manuals
  2. Jeep
  3. Automobile
  4. Grand Cherokee 2012
  5. Owner's Manual

Jeep Grand Cherokee 2012 Owner's Manual

Manual is about: Grand Cherokee 2012

Summary of Grand Cherokee 2012

  • Page 1

    Grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2 0 12 g ra n d c h e ro k e e 12wk741-126-aa first edition printed in u.S.A. 2 0 1 2 907713 jeep cherokee om cover.Indd 1 3/10/11 1:09 pm.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 5 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 7 䡵 vehicle ide...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the unive...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ wireless ignition node (win) . . . . . . . . . . . . 12 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ removing key fob from ignition . . . . . . . . . . 14 ▫ ...

  • Page 12

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . 24 ▫ programming additional transmitters . . . . . . 24 ▫ transmitter battery replacement . . . . . . . . . . 25 ▫ general information . . . . . . . . . . . . . . . . . . . 27 䡵 remote starting system — if equipped . . . . . . . 27 ▫ how to u...

  • Page 13

    ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . 59 ▫ supplemental active head restraints (ahr) . . 60 ▫ enhanced seat belt use reminder system (beltalert 威 ) . . . . . . . . . . . . . . . . . . . . . . . . . 64 ▫ seat belt lock out . . . . . . . . . . . . . . . . . . . . 65 ▫ seat belts ...

  • Page 14

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a wireless ignition node (win) with integral ignition switch. You can insert the key fob into the ignition switch with either side up. Keyless enter-n...

  • Page 15

    Key fob the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key ...

  • Page 16

    To remove the emergency key, slide the mechanical latch at the top of the key fob sideways with your thumb and then pull the key out with your other hand. Note: you can insert the double-sided emergency key into the lock cylinders with either side up. Removing key fob from ignition place the shift l...

  • Page 17

    • the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the off position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “electronic vehi...

  • Page 18

    Warning! (continued) • do not leave the key fob in or near the vehicle, and do not leave keyless enter-n-go in the acc or on/run mode. A child could operate power win- dows, other controls, or move the vehicle. • do not leave children or animals inside parked vehicles in hot weather. Interior heat b...

  • Page 19

    Vehicle can be used to start and operate the vehicle. The system will shut the engine off in two seconds if an invalid key fob is used to start the engine. After turning the ignition switch to the on/run posi- tion, the vehicle security light will turn on for three seconds for a bulb check. If the l...

  • Page 20

    Caution! • always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unat- tended. • with keyless enter-n-go, always remember to place the ignition in off. At the time of purchase, the original owner is provided with a four-digit personal identification number (pin). Ke...

  • Page 21

    Audio and visual signals, the horn will sound, the head- lights will turn on, park lamps and/or turn signals will flash repeatedly for three minutes. If the disturbance is still present (driver’s door, passenger door, other doors, ignition) after three minutes, the headlights, park lamps and/or turn...

  • Page 22

    Exterior zone (refer to ⬙ keyless enter-n-go ⬙ in ⬙ things to know before starting your vehicle ⬙ for further infor- mation). • press the lock button on the remote keyless entry (rke) transmitter. 3. If any doors are open, close them. To disarm the system the vehicle security alarm can be disarmed u...

  • Page 23

    • when the vehicle security alarm is armed, the interior power door lock switches will not unlock the doors. The vehicle security alarm is designed to protect your vehicle; however, you can create conditions where the system will give you a false alarm. If one of the previ- ously described arming se...

  • Page 24

    Note: • the front courtesy overhead console and door cour- tesy lights will turn on if the dimmer control is in the ⬙ dome on ⬙ position (extreme top position). • the illuminated entry system will not operate if the dimmer control is in the “dome defeat” position (extreme bottom position). Remote ke...

  • Page 25

    To unlock the doors press and release the unlock button on the rke transmitter once to unlock the driver’s door or twice to unlock all doors. The turn signal lamps will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Refer to “keyless enter-n-go” under “things...

  • Page 26

    To lock the doors press and release the lock button on the rke transmit- ter to lock all doors. The turn signal lamps will flash and the horn will chirp to acknowledge the signal. Refer to “keyless enter-n-go” under “things to know before starting your vehicle” for further information. Sound horn wi...

  • Page 27

    Transmitter battery replacement the recommended replacement battery is one cr2032 battery. Note: • perchlorate material — special handling may apply. See www.Dtsc.Ca.Gov/hazardouswaste/perchlorate • do not touch the battery terminals that are on the back housing or the printed circuit board. 1. Remo...

  • Page 28

    2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. 3. Remove and replace the battery. When replacing the battery, match the + sign on the battery to the + sig...

  • Page 29

    4. To assemble the rke transmitter case, snap the two halves together. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept ...

  • Page 30

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • liftgate/flipper glass closed • hazard switch off • brake switch inactive (brake pedal not pressed) • ignition key removed from ignition switc...

  • Page 31

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 32

    • the engine can be started two consecutive times with the rke transmitter. However, the ignition must be cycled by pushing the start/stop button twice (or the ignition switch must be cycled to the on/run position) before you can repeat the start sequence for a third cycle. To exit remote start mode...

  • Page 33

    • for vehicles not equipped with the keyless enter- n-go feature, the message “remote start active — insert key and turn to run” will display in the evic until you insert the key. Refer to “electronic vehicle information center (evic)” for further information. • for vehicles equipped with the keyles...

  • Page 34

    Door locks the power door locks can be manually locked from inside the vehicle by using the door lock knob. To lock each door, push the door lock knob on each door trim panel downward. To unlock the front doors, pull the inside door handle to the first detent. To unlock the rear doors, pull the door...

  • Page 35

    Warning! • for personal security and safety in the event of an accident, lock the vehicle doors when you drive, as well as when you park and leave the vehicle. • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or...

  • Page 36

    If you press the door lock switch while the key fob is in the ignition switch and the driver’s door is open, the doors will not lock. If a rear door is locked, it cannot be opened from inside the vehicle without first unlocking the door. The door may be unlocked manually by raising the lock knob. Au...

  • Page 37

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged (locked). Child-protection door lock location child-protection door lock function 2 things to know before starting your vehicle 35.

  • Page 38

    Note: for emergency exit from the rear seats when the child-protection door lock system is engaged, manually raise the door lock knob to the unlocked position, roll down the window, and open the door using the outside door handle. Keyless enter-n-go™ the passive entry system is an enhancement to the...

  • Page 39

    Note: if “unlock all doors 1st press” is programmed all doors will unlock when you grab hold of the driver’s front door handle. To select between “unlock driver door 1st press” and “unlock all doors 1st press”, refer to “electronic vehicle information center (evic)/personal settings (customer-progra...

  • Page 40

    Preventing inadvertent locking of passive entry rke transmitter in vehicle to minimize the possibility of unintentionally locking a passive entry rke transmitter inside your vehicle, the passive entry system is equipped with an automatic door unlock feature which will function if there is no key fob...

  • Page 41

    Note: if “unlock all doors 1st press” is programmed in evic, all doors will unlock when you push the button on the liftgate. If ⬙ unlock driver door 1st press ⬙ is programmed in evic, the liftgate and flipper glass will unlock when you press the button on the liftgate for further information, refer ...

  • Page 42

    Note: • after pressing the door handle lock button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • the pas...

  • Page 43

    Warning! Never leave children in a vehicle with the key in the ignition switch or leave a vehicle with keyless enter- n-go in the acc or on/run position. Occupants, particularly unattended children, can become en- trapped by the windows while operating the power window switches. Such entrapment may ...

  • Page 44

    During auto up. If this happens, pull the switch lightly to the first detent and hold it to close the window manually. Warning! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Resetting the auto up feature should the au...

  • Page 45

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 46

    Liftgate flipper glass the liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. Note: the liftgate flipper glass will not open if the liftgate is ajar. Once the liftgate flipper glass has been opened, ...

  • Page 47

    Power liftgate — if equipped the power liftgate may be opened by pulling up on the liftgate handle or by pressing the liftgate button on the remote keyless entry (rke) transmitter. Press the liftgate button on the rke transmitter twice within five seconds, to open the power liftgate. Once the liftga...

  • Page 48

    Warning! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. • the power liftgate will not operate if the liftgate flipper glass is open. • the power liftgate buttons will not o...

  • Page 49

    • if the liftgate handle is pulled while the power liftgate is opening, the liftgate motor will disengage to allow manual operation. • if the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and the liftgate must be opened or closed manu- ally...

  • Page 50

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belts for the driver and all passengers • advanced front air bags for driver and front passen- ger • supplemental active head restraints (ahr) located on top of th...

  • Page 51

    Infant and child restraint systems. For more information on latch, refer to lower anchors and tether for children (latch). Note: the advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severit...

  • Page 52

    3. The driver and front passenger seats should be moved back as far as practical to allow the advanced front air bags room to inflate. 4. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between...

  • Page 53

    Warning! (continued) • supplemental side air bag inflatable curtain (sabic) and seat-mounted side air bags (sab) also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • in a collision, you and your passengers can suffer much greater injuries if you...

  • Page 54

    Warning! • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much wo...

  • Page 55

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” latch plate latch plate to buckle 2 things to know before starting your vehicle 53.

  • Page 56

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you properly. In a sudden stop...

  • Page 57

    Tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. Warning! • a lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your ab- domen. Alw...

  • Page 58

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 59

    As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you will prefer a higher position. When you release the button, verify the shoulder belt anchorage is latched by pulling downward on the shoulder belt anchorage until it is locked into ...

  • Page 60

    • n/a — not applicable • alr — automatic locking retractor if the passenger seating position is equipped with an alr and is being used for normal usage: only pull the belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activa...

  • Page 61

    How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the belt and retractor assembly must be replaced if the seat belt ...

  • Page 62

    Note: these devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deplo...

  • Page 63

    Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: for more information on properly adjusting and positi...

  • Page 64

    1. Grasp the deployed ahr from the rear seat. 2. Position the hands on the top of the deployed ahr at a comfortable position. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand positioning points on ahr 1 — downward movement 2 — rearward moveme...

  • Page 65

    4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an autho...

  • Page 66

    Enhanced seat belt use reminder system (beltalert 姞 ) beltalert 威 is a feature intended to remind the driver and front passenger (if equipped with front passenger beltalert 威 ) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unb...

  • Page 67

    Seat belt lock out the center rear seat belt system has a lock out feature that will not allow you to extract the center webbing unless the rear seat upper latch is engaged. Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the moth...

  • Page 68

    The passenger’s advanced front air bag is mounted in the instrument panel, above the glove compartment. The words srs airbag are embossed on the air bag covers. Note: the driver and front passenger advanced front air bags are certified to the new federal regulations for advanced air bags. The advanc...

  • Page 69

    This vehicle is equipped with supplemental side air bag inflatable curtains (sabic) to protect the driver, front, and rear passengers sitting next to a window. The sabic air bags, are located above the side windows and their covers are also labeled: srs airbag. This vehicle is equipped with suppleme...

  • Page 70

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 71

    Supplemental seat-mounted side air bags (sab) supplemental seat-mounted side air bags (sab) may provide enhanced protection to help protect an occupant during a side impact. The sab is marked with an air bag label sewn into the outboard side of the front seats. When the air bag deploys, it opens the...

  • Page 72

    Supplemental side air bag inflatable curtain (sabic) sabic air bags may offer side-impact and vehicle roll- over protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each air bag features inflated chambers placed adjacent to the head of each outboa...

  • Page 73

    • should a vehicle rollover occur, the pretensioners and/or sab and sabic air bags on both sides of the vehicle may deploy. The system includes side impact sensors that are cali- brated to deploy the supplemental seat-mounted side air bags and sabic air bags during impacts that require side air bag ...

  • Page 74

    Along with seat belts and pretensioners, advanced front air bags work with the knee bolsters to provide im- proved protection for the driver and front passenger. Side air bags also work with seat belts to improve occupant protection. Air bag deployment sensors and controls occupant restraint control...

  • Page 75

    Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away f...

  • Page 76

    Warning! Ignoring the air bag warning light in your instru- ment panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have ...

  • Page 77

    Based on several factors, including the severity and type of collision, the side air bag inflator on the crash side of the vehicle may be triggered, releasing a quantity of non-toxic gas. The inflating sab exits through the seat seam into the space between the occupant and the door. The sab fully in...

  • Page 78

    Front and side impact sensors in front and side impacts, front and side impact sensors can aid the orc in determining the appropriate response to certain impact events. Enhanced accident response system in the event of an impact causing air bag deployment, if the communication network remains intact...

  • Page 79

    Floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • as the air bags deflate, you may see some smoke-like particles. The pa...

  • Page 80

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 81

    Air bag warning light you will want to have the air bags ready to inflate for your protection in a collision. The air bag warning light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. While the air bag system is designed to be maintenan...

  • Page 82

    • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if at all) the driver was depressing the accelerator and/or brake pedal; and, • how fast the vehicle was traveling. These data can help provide a better understanding of the circumstances in which crashes and in...

  • Page 83

    Seat owner’s manual to ensure you have the right seat for your child. Use the restraint that is correct for your child. Warning! In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap can become so gr...

  • Page 84

    Warning! • rearward-facing child seats must never be used in the front seat of a vehicle with the front passenger air bag. An air bag deployment could cause severe injury or death to infants in this position. • improper installation can lead to failure of an infant or child restraint. It could come ...

  • Page 85

    Restraint and slide the latch plate into the buckle. Then, pull the shoulder belt until it is fully extended from the retractor. Allow the belt to return into the retractor, pulling on the excess webbing to tighten the lap portion around the child restraint. For additional information, refer to ⬙ au...

  • Page 86

    All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seatback, the...

  • Page 87

    Also have features for installation using the vehicle’s seat belts. Child restraints having tether straps and hooks for connection to the top tether anchorages have been avail- able for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or r...

  • Page 88

    The vehicle’s seat belts. For typical installation instruc- tions, refer to “installing the latch-compatible child restraint system”. Installing the latch-compatible child restraint system we urge you to carefully follow the directions of the manufacturer when installing your child restraint. Not al...

  • Page 89

    Warning! Do not use the cargo tie downs located on the load floor. Improper usage of the tether can lead to a failure of an infant or child restraint. The child could be badly injured or killed. Pulling down the carpet floor panel to access top tether strap top tether strap anchorage (located on sea...

  • Page 90

    Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also b...

  • Page 91

    Seat belts are designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip. The alr will make a ratcheting noise if you extract the entire belt from the retractor and then allow the belt to retract into the retractor. For addit...

  • Page 92

    The upward position. To access the center seat arm rest tether first lower the arm rest. The tether is located behind the armrest and hooked onto the plastic seat backing. Pull down on the tether to unhook it from the plastic seat backing, then raise the armrest and attach the tether hook to the str...

  • Page 93

    Strap anchorages behind the rear seat, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchorages. Pulling down the carpet floor panel to access top tether strap top tether strap anchorage (located on seatback) 2 things to know before starting your vehicl...

  • Page 94

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly be- hind the child seat to secure a child restraint top tether strap. • do not use the cargo tie downs located on the load floor. Improper usag...

  • Page 95

    Top tether strap attachment for the center seating position route the tether strap over the seatback and headrest then attach the hook to the top tether anchorage located on the back of the seat behind the gap panel. For the outboard seating positions, route the tether strap under the headrests and ...

  • Page 96

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of diff...

  • Page 97

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 98

    Inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do n...

  • Page 99

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 100

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 101: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 ▫ automatic dimming mirror . . . . . . . . . . . . . 106 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . 107 ▫ outside mirrors folding feature . . . . . . . . . 107...

  • Page 102

    ▫ things you should know about your uconnect™ phone . . . . . . . . . . . . . . . . . . . . 136 ▫ general information . . . . . . . . . . . . . . . . . . 147 䡵 voice command — if equipped . . . . . . . . . . . 147 ▫ voice command system operation . . . . . . . . 147 ▫ commands . . . . . . . . . . . ...

  • Page 103

    ▫ to disable a rke transmitter linked to memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 ▫ easy entry/exit seat . . . . . . . . . . . . . . . . . . 173 䡵 to open and close the hood . . . . . . . . . . . . 174 䡵 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 ▫ h...

  • Page 104

    ▫ intermittent wiper system . . . . . . . . . . . . . . 186 ▫ windshield washer operation . . . . . . . . . . . 187 ▫ mist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 ▫ rain sensing wipers — if equipped . . . . . . . 188 䡵 tilt/telescoping steering column . . . . . . . . . . 190 䡵 ...

  • Page 105

    ▫ adaptive cruise control (acc) menu . . . . . 209 ▫ display warnings and maintenance . . . . . . . 210 ▫ precautions while driving with acc . . . . . . 214 ▫ general information . . . . . . . . . . . . . . . . . . 218 ▫ normal (fixed speed) cruise control mode . . . . . . . . . . . . . . . . . . . ...

  • Page 106

    ▫ programming a rolling code . . . . . . . . . . . 240 ▫ programming a non-rolling code . . . . . . . . 242 ▫ canadian/gate operator programming . . . . 243 ▫ using homelink 威 . . . . . . . . . . . . . . . . . . . 245 ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . 245 ▫ troubleshoo...

  • Page 107

    ▫ closing power shade — express . . . . . . . . . 253 ▫ closing power shade — manual mode . . . . . 253 ▫ pinch protect feature . . . . . . . . . . . . . . . . . 253 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . 253 ▫ sunroof maintenance . . . . . . . . . . . . . . . . . 254 ▫ ignitio...

  • Page 108

    Mirrors automatic dimming mirror this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will illuminate to indicate when the dim- ming feature is activated. The mirror ...

  • Page 109

    Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they ...

  • Page 110

    Mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. Power mirror preselected positions can be controlled by the optional memory seat feature. Refer to “driv...

  • Page 111

    Sun visor extension this feature has a pull out extension on the sun visor for increased coverage. Blind spot monitoring — if equipped the blind spot monitoring (bsm) system uses two radar- based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, truc...

  • Page 112

    When the vehicle is started, the bsm warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational. The bsm system sensors operate when the vehicle is in any forward gear or reverse and enters stand by mode when the vehicle is in pa...

  • Page 113

    The bsm system notifies the driver of objects in the detection zones by illuminating the bsm warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “modes of operation” for further information. The bsm system monitors the...

  • Page 114

    Entering from the side vehicles that move into your adjacent lanes from either side of the vehicle. Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Side monitoring rear monitor...

  • Page 115

    Overtaking traffic if you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h)...

  • Page 116

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The bsm system will not alert you of objects t...

  • Page 117

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicles mirrors, glance over your shoulder...

  • Page 118

    Note: in a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When rcp is on and the vehicle is in reverse, the driver is alerted using both the visua...

  • Page 119

    Signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and detected object are present on the same side at the same time, both the visual and audio alerts will be issued. In addition to the audible a...

  • Page 120

    Phone using simple voice commands (e.G., “call” ѧ “mike” ѧ “work” or “dial” ѧ “248-555-1212”). Your mobile phone’s audio is transmitted through your vehi- cle’s audio system; the system will automatically mute your radio when using the uconnect™ phone. Note: the uconnect™ phone requires a mobile pho...

  • Page 121

    Warning! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in a collision causing serious injury or death. Uconnect™ phone button the radio or steering wheel con...

  • Page 122

    Operation voice commands can be used to operate the uconnect™ phone and to navigate through the uconnect™ phone menu structure. Voice commands are required after most uconnect™ phone prompts. You will be prompted for a specific command and then guided through the available options. • prior to giving...

  • Page 123

    Cancel command at any prompt, after the beep, you can say “cancel” and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (link) uconnect™ phone to a mobile phone to begin using your uconnect™ phone, you must pair your compatib...

  • Page 124

    Phone to use if multiple mobile phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the uconnect™ phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at an...

  • Page 125

    Add names to your uconnect™ phonebook note: adding names to the uconnect™ phonebook is recommended when the vehicle is not in motion. • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook new entry”. • when prompted, say the name of the new entry. Use of long...

  • Page 126

    • to call a name from the uconnect™ phonebook or downloaded phonebook, follow the procedure in “call by saying a name” section. • automatic download and update, if supported, begins as soon as the bluetooth 威 wireless phone connection is made to the uconnect™ phone, for example, after you start the ...

  • Page 127

    • after the “ready” prompt and the following beep, say “phonebook edit entry”. • you will then be asked for the name of the phonebook entry that you wish to edit. • next, choose the number designation (home, work, mobile, or other) that you wish to edit. • when prompted, recite the new phone number ...

  • Page 128

    From the list, press the button while the uconnect™ phone is playing the desired entry and say “delete”. • after you enter the name, the uconnect™ phone will ask you which designation you wish to delete: home, work, mobile, other, or all. Say the designation you wish to delete. • note that only the ...

  • Page 129

    • to call one of the names in the list, press the button during the playing of the desired name, and say “call”. Note: the user can also exercise “edit” or “delete” operations at this point. • the uconnect™ phone will then prompt you as to the number designation you wish to call. • the selected numb...

  • Page 130

    When another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making a second call while current call is in progress to make a second call while you are currently on a call, press the button and say “dial” or “call” followed by the phone number or phonebook ent...

  • Page 131

    Call termination to end a call in progress, momentarily press the button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is ...

  • Page 132

    Uconnect™ phone features language selection to change the language that the uconnect™ phone is using: • press the button to begin. • after the “ready” prompt and the following beep, say the name of the language you wish to switch to english, espanol, or francais. • continue to follow the system prom...

  • Page 133

    Canada and 060 for mexico). The number dialed may not be applicable with the available mobile service and area. • if supported, this number may be programmable on some systems. To do this, press the button and say “setup”, followed by “emergency”. • the uconnect™ phone does slightly lower your chanc...

  • Page 134

    Paging to learn how to page, refer to “working with automated systems”. Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the uconnect™ phone. Voice mail calling to learn how to access your voice mail, refer to “working with automate...

  • Page 135

    The uconnect™ phone will then send the corresponding phone number associated with the phonebook entry, as tones over the phone. Note: • you may not hear all of the tones due to mobile phone network configurations. This is normal. • some paging and voice mail systems have system time out settings tha...

  • Page 136

    Dialing using the mobile phone keypad you can dial a phone number with your mobile phone keypad and still use the uconnect™ phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired bluetooth 威 mobil...

  • Page 137

    From your uconnect™ phone paired mobile phone to the uconnect™ phone or vice versa, press the button and say “transfer call”. Connect or disconnect link between the uconnect™ phone and mobile phone your mobile phone can be paired with many different electronic devices, but can only be actively “conn...

  • Page 138

    • the selected phone will be used for the next phone call. If the selected phone is not available, the uconnect™ phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m)) the vehicle. Delete uconnect™ phone paired mobile phones • press the button to ...

  • Page 139

    You can either press the uconnect™ phone button to restore the factory setting or repeat the words and phrases when prompted by the uconnect™ phone. For best results, the voice training session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blow...

  • Page 140

    • fully closed windows, • dry weather condition. • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, the system may not always work for some. • when navigating through an automated system such as voice mail, or when sending a page, at the...

  • Page 141

    • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect™ phone. • echo at the phone far end can sometimes be reduced by lowering the in-veh...

  • Page 142

    Send messages: you can send messages using uconnect™ phone. To send a new message: • press the button. • after the “ready” prompt and the following beep, say “sms send” or “send message.” • you can either say the message you wish to send or say “list messages.” there are 20 preset messages. To send ...

  • Page 143

    16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and th...

  • Page 144

    142 understanding the features of your vehicle.

  • Page 145

    3 understanding the features of your vehicle 143.

  • Page 146

    144 understanding the features of your vehicle.

  • Page 147

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 3 understa...

  • Page 148

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

  • Page 149

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 150

    If you ever wish to interrupt the system while it lists options, press the voice command button, listen for the beep, and say your command. Pressing the voice command button while the system is speaking is known as “barging in.” the system will be interrupted, and after the beep, you can add or chan...

  • Page 151

    3. Use the on/off volume rotary knob to adjust the volume to a comfortable level while the voice command system is speaking. Please note the volume setting for voice command is different than the audio system. Main menu start a dialogue by pressing the voice command button. You may say “main menu” t...

  • Page 152

    • “menu radio” (to switch to the radio menu) • “main menu” (to switch to the main menu) satellite radio to switch to satellite radio mode, say “sat” or “satellite radio”. In this mode, you may say the following com- mands: • “channel number” (to change the channel by its spoken number) • “next chann...

  • Page 153

    − “continue” (to continue recording) − “delete” (to delete the recording) • “play memos” (to play previously recorded memos) — during the playback you may press the voice command button to stop playing memos. You proceed by saying one of the following commands: − “repeat” (to repeat a memo) − “next”...

  • Page 154

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect™ voice “voice training” feature may be used. 1. Press the voice command button, say “system setup” and once you are in that menu then say “voice training.” this will train your...

  • Page 155

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 156

    Reclining the seatback the angle of the seatback can be adjusted forward or backward. Push the seatback switch forward or rear- ward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Warning! • adjusting a seat while driving may be dan...

  • Page 157

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting the seat up or down the height of the seats...

  • Page 158

    Caution! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Power lumbar — if equipped vehicles equipped with power driver or passenger seat...

  • Page 159

    Manual front seats forward/rearward adjustment some models may be equipped with manual front driver or passenger seats. The seats can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor. While sitting in the seat, lift up on the bar located under t...

  • Page 160

    Manual front passenger seatback adjustment — recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired position and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the sea...

  • Page 161

    Heated seats — if equipped on some models, the front and rear seats may be equipped with heaters in both the seat cushions and seatbacks. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- ha...

  • Page 162

    Programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to know before starting your vehicle” for further informa- tion. Front heated seats there are two heated seat switches that allow the driver and passenger to operate the seats independently. The c...

  • Page 163

    You can choose from high, low or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high-level heating. Press the switch a second time to select low-l...

  • Page 164

    Small fans that draw the air from the passenger compart- ment and blow air through fine perforations in the seat cover to help keep the driver and front passenger cooler in higher ambient temperatures. There are two ventilated seat switches that allow the driver and passenger to operate the seats in...

  • Page 165

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 166

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. For comfort the active head restraints can be tilted forward and rearward. To tilt the head restrain...

  • Page 167

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 168

    Warning! (continued) • active head restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the ac- tive head restraint ensure that all cargo is se- cured, as loose cargo could contact the active head restraint during sudden st...

  • Page 169

    Warning! Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure the outboard head re- straints are in their upright positions when the seat is to be occupied. Note: for proper routing of a child seat tether refer to ...

  • Page 170

    2. Fold the rear seat completely forward. To raise rear seat raise the rear seatback and lock it into place. If interfer- ence from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Warning! • be certain that the seatback is ...

  • Page 171

    Reclining rear seat to recline the seatback, lift the lever located on the outboard side of the seat, lean back and release the lever at the desired position. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the seatback reclined so that the shoul...

  • Page 172

    Driver memory seat — if equipped once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable steering wheel posi- tion (if equipped), and the radio station preset settings. Your remote keyless entry (rke) transmi...

  • Page 173

    Setting memory positions and linking remote keyless entry transmitter to memory note: each time the s (set) button and a numbered button 1 or 2 are pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key, and turn the ignition switch to the on/run posit...

  • Page 174

    To “electronic vehicle information center (evic)/ customer-programmable features” in “understanding your instrument panel” for further information. 12. Repeat the above steps to set the next memory position, using the other numbered memory button, or to link another rke transmitter to memory. Memory...

  • Page 175

    3. Press and release the memory s (set) button located on the driver’s door. 4. Within five seconds, press and release memory button 1 on the driver’s door. 5. Within five seconds, press and release the unlock button on the rke transmitter. To disable another rke transmitter linked to either memory ...

  • Page 176

    Driving position when the key is placed into the ignition, and turned out of the lock position toward the acc/on position. The easy entry/exit feature will be automatically dis- abled if the seat is already positioned closer than 0.9 in (23 mm) forward of the rear stop. At this position, there is no...

  • Page 177

    2. Reach under the hood, move safety latch to the left and lift the hood. Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. Warning! Be sure the hood is fully latched before driving your vehic...

  • Page 178

    Lights headlight switch the headlight switch is located on the left side of the instrument panel, next to the steering wheel. The head- light switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped). To turn on the headlights...

  • Page 179

    Caution! Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses. Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to...

  • Page 180

    Note: when your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “lights” in this section for further information. Smartbeam™ — if equipped the smartbeam™ system provides increased forward lighting at night by automa...

  • Page 181

    2. Push back on the multifunction lever once again to reactivate the system. Note: broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, e...

  • Page 182

    Parking lights and panel lights to turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the o (off) position. Fog lights — if equipped the fog lights are turned on by rotating the headlight ...

  • Page 183

    Interior lights courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the headlight switch) is rotated to the its farthest upward position, or if equipped, when the unlock button is pressed on the remote keyless entry (rk...

  • Page 184

    Lights-on reminder if the headlights, parking lights, or cargo lights are left on after the ignition is turned off, a chime will sound when the driver’s door is opened. Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. I...

  • Page 185

    Each light can be turned on by pressing a switch on either side of the console. These buttons are backlit for night time visibility. To turn the lights off, press the switch a second time. The lights will also turn on when the unlock button on the remote keyless entry (rke) is pressed. Ambient light...

  • Page 186

    Multifunction lever the multifunction lever is located on the left side of the steering column. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light re...

  • Page 187

    High/low beam switch push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off. Windshield wipers and washers the windshield wiper/washer control...

  • Page 188

    Windshield wiper operation rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation. Caution! Always remove any buildup of snow that prevents the windshield wiper blades fro...

  • Page 189

    Note: if the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield washer operation to use the washer, push on the end of the lever (toward the steering wheel) and hold while spray is desired. If the lever is pushed while in the intermittent setting, the wipers will t...

  • Page 190

    Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist use the mist...

  • Page 191

    The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position 1 is the least sensitive, and wiper delay position 4 is the most sensi- tive. Setting 3 should be used for normal rain conditions. Settings 1 and 2 can be used if the driver desires less wiper sensitivit...

  • Page 192

    • transmission in neutral position — when the ignition is on, and the transmission is in the neu- tral position, the rain sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 5 mph (8 km/h), or the shift lever is moved out of the neutral position. Tilt/teles...

  • Page 193

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this war...

  • Page 194

    Note: for vehicles equipped with driver memory seat, you can use your remote keyless entry (rke) transmitter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to pre-programmed positions. Refer to “driver memory seat” in this section for further infor...

  • Page 195

    Press the switch to turn on the heated steering wheel. The light on the switch will illuminate to indicate the steering wheel heater is on. Pressing the switch a second time will turn off the heated steering wheel and light indicator. Note: the engine must be running for the heated steering wheel to...

  • Page 196

    The electronic speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic ...

  • Page 197

    To set a desired speed turn the electronic speed control on. When the vehicle has reached the desired speed, press the set (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. Note: the vehicle should be traveling at a steady speed and on level ground b...

  • Page 198

    To accelerate for passing press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using electronic speed control on hills the transmission may downshift on hills to maintain the vehicle set speed. Note: the electronic speed control system ma...

  • Page 199

    Acc will allow you to keep cruise control engaged in light to moderate traffic conditions without the constant need to reset your cruise control. Acc utilizes a radar sensor designed to detect a vehicle directly ahead of you. Note: • if the sensor does not detect a vehicle ahead of you, acc will mai...

  • Page 200

    Warning! (continued) − cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions. − does not predict the lane curvature or the move- ment of preceding vehicles and will not compensate for such changes. − does not always fully recogniz...

  • Page 201

    The cruise control system has two control modes: • adaptive cruise control mode for maintaining an appropriate distance between vehicles. • normal (fixed speed) cruise control mode for cruising at a constant preset speed. For additional information, refer to “normal (fixed speed) cruise control mode...

  • Page 202

    Note: any chassis/suspension modifications to the vehicle will effect the performance of the adaptive cruise control. Activating adaptive cruise control (acc) you can only activate acc if the vehicle speed is above 20 mph (32 km/h). When the system is turned on and in the ready state, the electronic...

  • Page 203

    To activate push and release the on/off button. The acc menu in the evic displays “adaptive cruise ready.” to turn the system off, push and release the on/off button again. At this time, the system will turn off and the evic will display “adaptive cruise control off.” warning! Leaving the adaptive c...

  • Page 204

    To set a desired acc speed when the vehicle reaches the speed desired, push the set - button and release. The evic will display the set speed. Remove your foot from the accelerator pedal. If you do not, the vehicle may continue to accelerate beyond the set speed. If this occurs: • the message “drive...

  • Page 205

    To cancel the system will disable acc without erasing the memory if: • you softly tap the brake pedal. • you depress the brake pedal. • you press the cancel switch. • an anti-lock brake system (abs) event occurs. • a trailer sway control (tsc) event occurs. • if the transmission is shifted into neut...

  • Page 206

    Note: if acc is resumed or set with the esc/tcs off, esc will automatically be re-engaged. To turn off the system will turn off and erase the set speed in memory if: • you push the on/off button. • you turn off the ignition. • you switch to four-wheel drive low. To resume speed press the res + butto...

  • Page 207

    To vary the speed setting while acc is set, you can increase the set speed by pressing and holding the res + button. If the button is continually pressed, the set speed will continue to in- crease in 5 mph (8 km/h) increments until the button is released. The increase in set speed is reflected in th...

  • Page 208

    Setting the following distance in acc the specified following distance for acc can be set by varying the distance setting between 3 (long), 2 (me- dium), and 1 (short). Using this distance setting and the vehicle speed, acc calculates and sets the distance to the vehicle ahead. This distance setting...

  • Page 209

    To change the distance setting, press the distance button and release. Each time the button is pressed, the distance setting adjusts between long, medium, and short. If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle is detected in the same lane, the ev...

  • Page 210

    The maximum braking applied by acc is limited; how- ever, the driver can always apply the brakes manually, if necessary. Note: the brake lights will illuminate whenever the acc system applies the brakes. A proximity warning will alert the driver if acc predicts that its maximum braking level is not ...

  • Page 211

    Adaptive cruise control (acc) menu the evic displays the current acc system settings. The evic is located in the upper part of the instrument cluster between the speedometer and the tachometer. The information it displays depends on acc system status. Press the menu button (located on the steer- ing...

  • Page 212

    The acc screen will display once again if any acc activity occurs, which may include any of the following: • set speed change • distance setting change • system cancel • driver override • system off • acc proximity warning • acc unavailable warning the evic will return to the last display selected a...

  • Page 213

    Note: if the acc “clean radar sensor in front of vehicle” warning is active normal (fixed speed) cruise control is still available. For additional information refer to “normal (fixed speed) cruise control mode” in this section. If weather conditions are not a factor, the driver should examine the se...

  • Page 214

    • do not attach or install any accessories near the sensor, including transparent material or aftermarket grilles. Doing so could cause an acc system failure or malfunction. When the condition that deactivated the system is no longer present, the system will return to the “adaptive cruise control of...

  • Page 215

    Note: do not change the adjustment fasteners or pull the sensor off of the bracket. Doing so may misalign the sensor. Store the sensor and bracket assembly in a safe location. The wiring and connector must be stowed properly after the sensor and bracket assembly is removed. A connector plug is stowe...

  • Page 216

    Service acc warning if the system turns off, and the evic displays “acc/ fcw unavailable service radar sensor”, it indicates there is an internal system fault. Although the vehicle is still drivable under normal conditions, have the system checked by an authorized dealer. Precautions while driving w...

  • Page 217

    Offset driving acc may not detect a vehicle in the same lane that is offset from your direct line of travel. There will not be sufficient distance to the vehicle ahead. The offset vehicle may move in and out of the line of travel, which can cause your vehicle to brake or accelerate unexpectedly. Tur...

  • Page 218

    Using acc on hills when driving on hills, acc may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, acc perfor- mance may be limited. Lane changing acc will not detect a vehicle until it is completely in the lane in which you...

  • Page 219

    Narrow vehicles some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There will not be suffi- cient distance to the vehicle ahead. 3 understanding the features of your vehicle 217.

  • Page 220

    Stationary objects and vehicles acc does not react to stationary objects and stationary vehicles. For example, acc will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if nece...

  • Page 221

    Warning! In the normal cruise control mode, the system will not react to vehicles ahead. In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is ...

  • Page 222

    To resume press the res + button and then remove your foot from the accelerator pedal. The evic will display the last set speed. To turn off the system will turn off and erase the set speed in memory if: • you push the on/off button. • you turn off the ignition. • you engage four-wheel drive low. If...

  • Page 223

    Note: • the minimum speed for fcw activation is 10 mph (16 km/h). • when entering or driving in a curve, the fcw alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course predic- tion. This is expected and is a part of normal fcw activation and func...

  • Page 224

    Fcw settings can only be changed when the vehicle is in park. The default status of fcw is the “far” setting, this allows the system to warn you of a possible collision with the vehicle in front of you when you are farther away. This gives you the most reaction time. Changing the fcw status to the “...

  • Page 225

    Changing the fcw status to “off” prevents the system from warning you of a possible collision with the vehicle in front of you. Note: in the “off” setting fcw off will be displayed in the evic. Example only fcw off example 3 understanding the features of your vehicle 223.

  • Page 226

    Note: • the system will retain the last setting selected by the driver after ignition shut down. • fcw will not react to irrelevant objects such as over- head objects, ground reflections, objects not in the path of the car, stationary objects that are far away, oncom- ing traffic, or leading vehicle...

  • Page 227

    Parksense 姞 rear park assist — if equipped the parksense 威 rear park assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to parksense 威 system usage precautions for limitations of...

  • Page 228

    The parksense 威 warning display is located in the instru- ment cluster’s evic display. It provides both visual and audible warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. Parksense 姞 display when the vehicle is in reverse, the warning display will turn on ...

  • Page 229

    The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the evic display will show fewer arcs and the sound tone will change from slow, to fast, to continuous. Park assist system off slow tone 3 under...

  • Page 230

    The vehicle is close to the obstacle when the evic display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: fast tone continuous tone 228 understanding the features of your vehicle.

  • Page 231

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-39 in (200-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible alert chime none single 1/2 second tone slow fast continuous display message park assist system on warning object detected warning object de...

  • Page 232

    “electronic vehicle information center (evic)” in “un- derstanding your instrument panel” for further informa- tion. When the shift lever is moved to reverse and the system is disabled, the evic will display the “park assist system off” message for as long as the vehicle is in reverse. The parksense...

  • Page 233

    Parksense 姞 system usage precautions note: • ensure that the rear bumper is free of snow, ice, mud, dirt and debris to keep the parksense 威 system operat- ing properly. • jackhammers, large trucks, and other vibrations could affect the performance of parksense 威 . • when you turn parksense 威 off, th...

  • Page 234

    • on vehicles equipped with a tailgate, parksense 威 should be disabled when the tailgate is in the lowered or open position and the vehicle is in reverse. A lowered tailgate could provide a false indication that an obstacle is behind the vehicle. Caution! • parksense 威 is only a parking aid and it i...

  • Page 235

    Warning! (continued) • before using the parksense 威 rear park assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles becau...

  • Page 236

    When displayed, static grid lines will illustrate the width of the vehicle while a dashed center-line will indicate the center of the vehicle to assist with aligning to a hitch/ receiver. The static grid lines will show separate zones that will help indicate the distance to the rear of the vehicle. ...

  • Page 237

    Warning! Drivers must be careful when backing up even when using the parkview 威 rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your...

  • Page 238

    4. Enable or disable the rear camera feature by selecting the “enable rear camera in reverse” soft-key. 5. Press the “save” soft-key. Turning parkview 姞 on or off — without navigation/multimedia radio 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 3. Enable or disable the rear came...

  • Page 239

    To turn the lights off, press the switch a second time. The lights also turn on when a door is opened. The lights will also turn on when the unlock button on the rke is pressed. Courtesy lights the courtesy lights can be turned on by pressing the top corner of the lens. To turn the lights off, press...

  • Page 240

    Sunglass bin door at the front of the console a compartment is provided for the storage of a pair of sunglasses. The storage compart- ment access is a “push/push” design. Push the chrome pad on the door to open. Push the chrome pad on the door to close. Garage door opener — if equipped homelink 威 re...

  • Page 241

    Note: homelink 威 is disabled when the vehicle secu- rity alarm is active. Homelink 威 buttons/overhead consoles homelink 威 buttons/sunvisor/headliner 3 understanding the features of your vehicle 239.

  • Page 242

    Before you begin programming homelink 姞 be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the ...

  • Page 243

    1. Turn the ignition switch to the on/run position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink 威 button you wish to program while keeping the homelink 威 indicator light in view. 3. Simultaneously press and hold both the homelink 威 button you want to program and t...

  • Page 244

    Note: you have 30 seconds in which to initiate the next step after the learn button has been pressed. 6. Return to the vehicle and press the programmed homelink 威 button twice (holding the button for two seconds each time). If the garage door opener/device activates, programming is complete. Note: i...

  • Page 245

    4. Continue to hold both buttons and observe the indi- cator light. The homelink 威 indicator will flash slowly and then rapidly after homelink 威 has received the fre- quency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid. 5. Press and...

  • Page 246

    To pick up the signal during programming. Similar to this canadian law, some u.S. Gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. 1. Turn the ignition switc...

  • Page 247

    Reprogramming a single homelink 威 button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink 威 button until the indicator light begins to flash after 20 seconds. Do not release the but...

  • Page 248

    Troubleshooting tips if you are having trouble programming homelink 威 , here are some of the most common solutions: • replace the battery in the original hand-held transmit- ter. • press the learn button on the garage door opener to complete the training for a rolling code. • did you unplug the devi...

  • Page 249

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 250

    Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • in a collision, there is a gre...

  • Page 251

    Position. The sunroof will close fully and stop automati- cally. This is called “express close”. During express close operation, any movement of the switch will stop the sunroof. Closing sunroof — manual mode to close the sunroof, press and hold the switch in the forward position. Any release of the...

  • Page 252

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) is in certain open or partially open positions. This is a normal occur- rence a...

  • Page 253

    Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • in a collision, there is a gre...

  • Page 254

    Opening sunroof — express press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automati- cally. This is called “express open”. During express open operation, any movement of the sunroof switch ...

  • Page 255

    Opening power shade — manual mode to open the shade, press and hold the switch rearward to full open. Any release of the switch will stop the move- ment and the shade will remain in a partially opened condition until the switch is pushed and held rearward again. Closing power shade — express press t...

  • Page 256

    Together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof maintenance use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition off operation the power sunroof switches...

  • Page 257

    Note: • all accessories connected to the “battery” powered outlets should be removed or turned off when the vehicle is not in use to protect the battery against discharge. • to ensure proper operation a mopar 威 knob and element must be used. Caution! Power outlets are designed for accessory plugs on...

  • Page 258

    In addition to the front power outlet, there is also a power outlet located in the storage area of the center console. The rear power outlet is located in the right rear cargo area. Note: the rear power outlet can be switched to “battery” powered all the time by switching the power outlet right rear...

  • Page 259

    Power outlet right rear quarter panel fuse power outlet fuse locations 1 — m7 fuse 20 a yellow power outlet right rear quarter panel 2 — m6 fuse 20 a yellow cigar lighter instrument panel 3 — m36 fuse 20 a yellow power outlet console bin 3 understanding the features of your vehicle 257.

  • Page 260

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 261

    Power inverter — if equipped there is a 115 volt, 150 watt inverter outlet located on the back of the center console to convert dc current to ac current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 watts. Certain high-end video games, su...

  • Page 262

    The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximat...

  • Page 263

    Cupholders there are two cupholders for the front seat passengers located in the center console. There are two cupholders for the rear seat passengers located in the fold-down center armrest. Front cupholder location rear cupholders 3 understanding the features of your vehicle 261.

  • Page 264

    Storage glove compartment the glove compartment is located on the right side of the instrument panel. To open the glove compartment, pull outward on the latch and lower the glove box door. Glove compartment opened glove compartment 262 understanding the features of your vehicle.

  • Page 265

    Door storage large storage areas are built into the door panels for easy access. Center console the center console contains both an upper and a lower storage area. Door panel storage storage compartment 3 understanding the features of your vehicle 263.

  • Page 266

    To open the upper storage compartment, pull upward on the small latch located on the lid. Lift upward on the larger of the latches to access the lower storage compartment. Storage compartment latches lower storage compartment 264 understanding the features of your vehicle.

  • Page 267

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injur...

  • Page 268

    To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Cargo storage bins there are four removable storage bins located in the rear cargo area. There are two storage bins located on either side of the cargo area. Three-press switch rear storage b...

  • Page 269

    Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether hook (attached to the bottom of the load floor) to the liftgate opening. Tether strap lower storage bins 3 understanding the features of your vehicle 267.

  • Page 270

    Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the...

  • Page 271

    Warning! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. D...

  • Page 272

    Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. • cargo tie-down hooks are not safe anchors for a child seat t...

  • Page 273

    Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the control lever. The control lever is located on the left side of the steering column. Rotate the center portion of the lever upward to the first detent for intermittent operation and to...

  • Page 274

    If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “park” position. If the liftgate flipper glass is open, the rear window wiper/washer functionality is interrupted and the wiper stops at that “park” position. When the liftgate flipper glass is...

  • Page 275

    Roof luggage rack — if equipped the crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Note: if not equipped with crossbars, your authorized ...

  • Page 276

    Caution! • to prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without the crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other ...

  • Page 277: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 279 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 280 䡵 instrument cluster descriptions . . . . . . . . . . . 281 䡵 electronic vehicle information center (evic) . . 291 ▫ electronic ...

  • Page 278

    ▫ turn menu off . . . . . . . . . . . . . . . . . . . . . . 314 ▫ tire psi . . . . . . . . . . . . . . . . . . . . . . . . . . . 315 ▫ keyless enter-n-go display — if equipped . . . . . . . . . . . . . . . . . . . . . . . . 316 ▫ compass / temperature display . . . . . . . . . 316 ▫ customer-program...

  • Page 279

    ▫ uconnect™ multimedia (satellite radio) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . 347 ▫ operating instructions (uconnect™ phone) — if equipped . . . . . . . . . . . . . . . . . . . . . . 351 䡵 ipod 威 /usb/mp3 control — if equipped . . . . . 351 ▫ connecting the ipod 威 or externa...

  • Page 280

    ▫ replacing the batteries . . . . . . . . . . . . . . . . 373 ▫ headphones operation . . . . . . . . . . . . . . . . 374 ▫ controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 ▫ replacing the batteries . . . . . . . . . . . . . . . . 376 ▫ unwired 威 stereo headphone lifetime limited wa...

  • Page 281

    Instrument panel features 1 — air outlet 6 — lower switch bank 11 — hood release 2 — instrument cluster 7 — hazard switch 12 — fuel door release 3 — radio 8 — storage bin 13 — headlight switch 4 — glove compartment 9 — esc button 14 — dimmer control 5 — climate controls 10 — ignition switch 4 unders...

  • Page 282

    Instrument cluster 280 understanding your instrument panel.

  • Page 283

    Instrument cluster descriptions 1. Tachometer indicates the engine speed in revolutions per minute (rpm x 1000). 2. Air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to the on/run position. If the light is either not on d...

  • Page 284

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to...

  • Page 285

    5. Tow/haul indicator light — if equipped this light will illuminate when the tow/ haul button has been selected. The tow/ haul button is located in the center of the instrument panel (below the climate controls). 6. Turn signal indicator the arrows will flash with the exterior turn signals when the...

  • Page 286

    As it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ service,...

  • Page 287

    Maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicato...

  • Page 288

    12. Park/headlight on indicator — if equipped this indicator will illuminate when the park lights or headlights are turned on. 13. Seat belt reminder light when the ignition switch is first turned to the on/run position, this light will turn on for four to eight seconds as a bulb check. During the b...

  • Page 289

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 290

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Anti-lock brake (abs) light this light monitors the anti-lock brake sy...

  • Page 291

    19. Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position. 20. Electronic vehicle information center (evic) white telltale area this area will display the evic reconfigurable white telltales. For further information, refer to “electronic v...

  • Page 292

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If ...

  • Page 293

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • vehicle information warning message displays • personal settings (cus...

  • Page 294

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: up button press and release the up button to scroll up- ward through the main menus (fuel economy, vehicle info, tire psi, cruise, messages, units, system setup, vehicle speed, trip in...

  • Page 295

    Back button press the back button to scroll back to a previous menu or sub-menu. Electronic vehicle information center (evic) displays the evic display consists of three sections: 1. The top line where compass direction, odometer line and outside temperature are displayed. 2. The main display area w...

  • Page 296

    • unstored messages until run these messages deal primarily with the remote start feature. This message type is displayed until the ignition is in the run state. Examples of this message type are ⬙ remote start aborted - door ajar ⬙ and ⬙ press brake pedal and push button to start ⬙ . • five second ...

  • Page 297

    • keyfob battery low • liftglass open • left front turn signal lamp out • right front turn signal lamp out • left rear turn signal lamp out • right rear turn signal lamp out • low tire pressure • esc system off • service blind spot system • blind spot detection unavailable • blind spot system off • ...

  • Page 298

    • acc cancelled — to disable the acc system. Refer to “adaptive cruise control (acc)” in “understanding the features of your vehicle” (if equipped). • sensed vehicle indicator — the system detects a slower moving vehicle in the same lane. Refer to “adaptive cruise control (acc)” in “understanding th...

  • Page 299

    • acc/fcw unavailable service radar sensor — if the acc system turns off due to an internal system fault that requires service from an authorized dealer. Refer to “adaptive cruise control (acc)” in “understand- ing the features of your vehicle” (if equipped). • cruise off when park brake is on • acc...

  • Page 300

    • memory system unavailable — not in park • memory system unavailable — seatbelt buckled • memory 1 profile recall • memory 2 profile recall • press brake pedal and push button to start • wrong key • damaged key • key not programmed • function currently unavailable — power liftgate • unlock to opera...

  • Page 301

    • terrain system settings not available • raising vehicle ride height (with icon) • lowering vehicle ride height (with icon) • normal vehicle ride height — this message is dis- played (for 5 seconds) when the vehicle has achieved the normal vehicle ride height. • off road ride height level 1 — this ...

  • Page 302

    • selected ride height not permitted — the vehicle speed is too high to enter one of the preset levels (entry/exit level/off road ride height level 1/off road ride height level 2). • air suspension system cooling down – please wait — this message is displayed if the compressor tempera- ture level is...

  • Page 303

    • electronic speed control set this light will turn on when the electronic speed control is set. For further information, refer to “electronic speed control” in “under- standing the features of your vehicle.” • adaptive cruise control (acc) on this light will turn on when the acc is on. For further ...

  • Page 304

    • if the condition persists, see your authorized dealer for service. Evic amber telltale lights this area will show reconfigurable amber caution tell- tales. These telltales include: • forward collision warning (fcw) off this light warns the driver of a potential colli- sion with the vehicle in fron...

  • Page 305

    A loose, improperly installed, or damaged fuel filler cap may also turn on the malfunction indicator light (mil). • windshield washer fluid low indicator this light will turn on to indicate the wind- shield washer fluid is low. • serv 4wd the serv 4wd light monitors the electric shift 4wd system. If...

  • Page 306

    • oil pressure warning light this telltale indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This...

  • Page 307

    Required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • engine temperature warning light this light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches h, this indicator will illuminate and...

  • Page 308

    Warning! If the transmission temperature warning light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. Engine oil change indicator system oil change due your v...

  • Page 309

    Vehicles not equipped with keyless enter-n-go 1. Turn the ignition switch to the on/run position (do not start the engine.) 2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 3. Turn the ignition switch to the off/lock position. Note: if the indicator message illuminates ...

  • Page 310

    (mds) (if equipped) allows the engine to operate on four cylinders, or if you are driving in a fuel efficient manner. This feature allows you to monitor when you are driving in a fuel efficient manner, and it can be used to modify driving habits in order to increase fuel economy. Distance to empty (...

  • Page 311

    Vehicle speed press and release the up or down button until “vehicle speed” displays highlighted in the evic and press the select button. Press the select button to display the current speed in mph or km/h. Pressing the select button a second time will toggle the unit of measure between mph or km/h....

  • Page 312

    Elapsed time shows the total elapsed time of travel since the last reset when the ignition switch is in the acc position. Elapsed time will increment when the ignition switch is in the on or start position. To reset the display reset will only occur while a resettable function is being displayed. Pr...

  • Page 313

    This light will illuminate when the sport mode is selected. This mode provides performance based tuning with improved handling through an electronic controlled damping system. This system reduces body roll and pitch in many driving situations including cornering, acceleration and braking. For furthe...

  • Page 314

    • pressing the select button will clear the current run time and display the vehicle’s best 0-60 mph (0-100 km/h) time. • to clear the vehicle’s best 0-60 mph (0-100 km/h) time, press and hold the select button for five seconds. Braking distance when selected, this screen displays the vehicle’s brak...

  • Page 315

    • dashes will display if the vehicle fails to reach 1/8 mile (1/4 mile) in less then 30 seconds. • the time and speed will continue to display until the select button is pressed. • pressing the select button will clear the current run and display the vehicle’s best 1/8 mile (1/4 mile) run. • to clea...

  • Page 316

    Press the up and down button to scroll through the available information displays, then press select to display any one of the following choices. • coolant temp displays the actual coolant temperature. • oil temperature displays the actual oil temperature. • oil pressure displays the actual oil pres...

  • Page 317

    Tire psi press and release the up or down button until “tire psi” displays highlighted in the evic and press the select button. Press and release the up/down but- tons until one of the following system status messages displays in the evic: • system ok • system warnings displayed (will display all cu...

  • Page 318

    To “tires-general information/tire inflation pres- sures” in “starting and operating” for additional information. • your system can be set to display pressure units in psi, kpa, or bar. Keyless enter-n-go display — if equipped when the engine start/stop button is pressed to change ignition switch po...

  • Page 319

    Metallic objects) until the cal indicator displayed in the evic turns off. The compass will now function normally. Note: a good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. Compass varia...

  • Page 320

    3. Press the down button until the “compass variance” message is displayed in the evic, then press the select button. The last variance zone number displays in the evic. 4. Press and release the select button until the proper variance zone is selected, according to the map. 5. Press and release the ...

  • Page 321

    Out of park or the vehicle begins moving, a warning message setup not available, is followed in three seconds by, vehicle not in park. Press and release the up or down button until setup displays in the evic. Use the up or down button to display one of the following choices. Select language when in ...

  • Page 322

    Remote unlock sequence when unlock driver door only on 1st press is selected, only the driver’s door will unlock on the first press of the rke transmitter unlock button. When driver door 1st press is selected, you must press the rke transmitter unlock button twice to unlock the passenger’s doors. Wh...

  • Page 323

    Removed showing the system has been deactivated. Refer to “driver memory seat” in “understanding the fea- tures of your vehicle.” remote start comfort sys. When this feature is selected and the remote start is activated, the heated steering wheel and driver heated seat features will automatically tu...

  • Page 324

    With or without the sound horn on lock feature selected. To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Headlamp off delay when this...

  • Page 325

    Note: the seat will return to the memorized seat location (if recall memory with remote key unlock is set to on) when the rke transmitter is used to unlock the door. Refer to “driver memory seat” in “understanding the features of your vehicle” for further information. Tilt mirror in reverse when thi...

  • Page 326

    Display eco symbol — if equipped the “eco” message is located in the compass/ temperature display; this message can be turned on or off. To make your selection, press and release the select button until a check-mark appears next to the setting, showing that the setting has been selected. Keyless ent...

  • Page 327

    Been deactivated. When this feature is deactivated, the system reverts to the standard intermittent wiper operation. Hill start assist (hsa) when this feature is selected, the hsa system is active. Refer to “electronic brake control system” in “starting and operating” for system function and operati...

  • Page 328

    Warn you of a possible collision with the vehicle in front of you when you are farther away. This gives you the most reaction time. To change the setting for more dynamic driving select the near setting. This warns you of a possible collision with the vehicle in front of you when you are much closer...

  • Page 329

    Media center 730n/430/430n (rhr/rer/rbz/ rhb) cd/dvd/hdd/nav — if equipped note: the sales code is located on the lower right side of the unit’s faceplate. Refer to your uconnect™ multimedia rhr, rer, rbz or rhb user’s manual for detailed operating instructions. Operating instructions (voice command...

  • Page 330

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 331

    4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the ...

  • Page 332

    Am/fm button press the buttons to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button. The symbol set 1 will now show in the display window. Select the button (1 to 6) you w...

  • Page 333

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 334

    If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ejecting with the ignition off is not allowed on convertible or soft-...

  • Page 335

    Notes on playing mp3 files the radio can play mp3 files; however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restric- tions. Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw...

  • Page 336

    Discs created with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for cd audio or mp3 playback may result in longer disc loading times. Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 fil...

  • Page 337

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 338

    Media center 130 with satellite radio (sales code res+rsc) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volume control (rota...

  • Page 339

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Voice command system (radio) — if equipped refer to “voice command” in the uconnect™ user ma...

  • Page 340

    3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob or wait fi...

  • Page 341

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 342

    Program type 16-digit character display information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports spor...

  • Page 343

    Hours, press the tune/scroll control knob to set the minutes. The minutes will begin to blink. Adjust the minutes using the right side tune/scroll control knob. Press the tune/scroll control knob to save time change. Am/fm button press the button to select either am or fm mode. Set/rnd button — to s...

  • Page 344

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on/run or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks a...

  • Page 345

    If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ejecting with the ignition off is not allowed on convertible or soft-...

  • Page 346

    Notes on playing mp3 files the radio can play mp3 files; however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restric- tions. Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw...

  • Page 347

    Discs created with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for cd audio or mp3 playback may result in longer disc loading times. Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 fil...

  • Page 348

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 349

    Press and hold the info button again for three seconds to return to ⬙ elapsed time ⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or cassette player and utilize the vehicle’s ...

  • Page 350

    Radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, including how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www- .Siriuscanada.Ca for ...

  • Page 351

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 352

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the channel. Music type button pressing thi...

  • Page 353

    Selected within five seconds after pressing the set but- ton, the channel will continue to play but will not be stored into pushbutton memory. You may add a second channel to each pushbutton by repeating the above procedure with this exception: press the set button twice and set 2 will show in the d...

  • Page 354

    Ipod 威 control supports mini, 4g, photo, nano, 5g ipod 威 and iphone 威 devices. Some ipod 威 software versions may not fully support the ipod 威 control features. Please visit apple’s website for software updates. Note: • if the radio has a usb port, refer to the appropriate uconnect™ multimedia radio ...

  • Page 355

    Without damaging it while closing the lid. If a cut out is not available in the center console base, route the cable away from the lid latch and in a place that will allow the lid to close without damaging the cable. Once the audio device is connected and synchronized to the vehicle’s ipod 威 /usb/mp...

  • Page 356

    Control mode, audio tracks (if available from audio device) start playing over the vehicle’s audio system. Play mode when switched to ipod 威 /usb/mp3 control mode, the ipod 威 or external usb device automatically starts play mode. In play mode, the following buttons on the radio faceplate may be used...

  • Page 357

    To the next screen of data for that track. Once all screens have been viewed, the last info button press will go back to the play mode screen on the radio. • pressing the repeat button will change the audio device mode to repeat the current playing track or press the vr button and say ⬙ repeat on ⬙ ...

  • Page 358

    Fast will scroll through the list faster. During fast scroll, a slight delay in updating the information on the radio display may be noticeable. • during all list modes, the ipod 威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backward (c...

  • Page 359

    Caution! • leaving the ipod 威 or external usb device (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufactur- er’s guidelines. • placing items on the ipod 威 or external usb device, or connections to the ipod...

  • Page 360

    2. After the ⬙ ready ⬙ prompt and the following beep, say ⬙ setup ⬙ , then ⬙ select audio devices ⬙ . 3. Say the name of the audio device or ask the uconnect™ phone system to list audio devices. Next track use the seek up button, or press the vr button on the radio and say “next track” to jump to th...

  • Page 361

    • with the ignition switch in the on or acc position, turn the radio on by pushing the on/off volume control knob. • when the video screen are open and a dvd is inserted into the radio, the screen turns on automatically, the headphone transmitters turn on and playback begins. Single video screen not...

  • Page 362

    2. While looking at the video screen, highlight disc by either pressing up/down/left/right buttons or by re- peatedly pressing the mode button, then press enter on the remote control. Note: the ves™ system will retain the last setting when turned off. Using the touch-screen radio controls 1. Press t...

  • Page 363

    3. Touch the 1 soft-key and then the disc soft-key in the media column. To exit touch the back arrow soft-key at the top left of the screen. Note: the “1” and “2” soft-keys are displayed for the headphone channels. Touch 1 or 2 based on which channel you want to change, select the new mode from the ...

  • Page 364

    Note: • to view a dvd on the radio press the radio/media hard-key, on the radio faceplate, then touch the disc tab soft-key and then the view video soft-key. • viewing a dvd on the touch-screen radio screen is not available in all states/provinces, and the vehicle must be stopped, and the shift leve...

  • Page 365

    When connecting an external source to the aux input, be sure to follow the standard color coding for the ves™ jacks: note: certain high-end video games, such as play- station3 and xbox360 will exceed the power limit of the vehicle’s power inverter. Refer to the power inverter section in your vehicle...

  • Page 366

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. Touch the 1 or 2 based on the headphone c...

  • Page 367

    Listen to an audio source on channel 2 while a video is playing on channel 1 ensure the remote control and headphone switch is on channel 2. Using the remote control 1. Press the mode button on the remote control and the mode select screen will display, unless a video is playing then only a small ba...

  • Page 368

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. To listen to an audio source on channel 2...

  • Page 369

    Important notes for single video screen system • ves™ is able to transmit two channels of stereo audio simultaneously. • in split screen mode the left side equates to channel 1 and right side equates to channel 2. • if a video source is selected on channel 1, then channel 2 is for audio only. Select...

  • Page 370

    Using the remote control 1. Press the mode button on the remote control. 2. While looking at screen 1, highlight disc by either pressing up/down/left/right buttons or by repeatedly pressing the mode button, then press enter. Note: • channel/screen 1 select mode information is shown on the left side ...

  • Page 371

    3. Touch the 1 or 2 soft-key based on the channel you want to change and then the disc soft-key in the media column. To exit touch the back arrow at the top left of the screen. Note: • to view a dvd on the radio press the radio/media hard-key, on the radio faceplate, then touch the disc tab soft-key...

  • Page 372

    Remote control controls and indicators 1. Power – turns the screen and wireless headphone transmitter for the selected channel on or off. To hear audio while the screen is closed, press the power button to turn the headphone transmitter on. 2. Channel selector indicators – when a button is pressed, ...

  • Page 373

    6. 䉲 / prev – in radio modes, press to select to the previous station. In disc modes, press to advance to the start of the current or previous audio track or video chapter. In menu modes, use to navigate in the menu. 7. Menu – press to return to the main menu of a dvd disc, to select a satellite aud...

  • Page 374

    And the disc is stopped, press the setup button to access the dvd setup menu. (see the dvd setup menu of this manual.) 16. Back – when navigating in menu mode, press to return to the previous screen. When navigating a dvds disc menu, the operation depends on the disc’s contents. 17. 䉳䉳 – in radio mo...

  • Page 375

    Locking the remote control all remote control functionality can be disabled as a parental control feature. • to disable the remote control from making any changes, press the video lock button add follow the radio’s instructions (select menu, rear ves, lock). If the vehicle is not equipped with a dvd...

  • Page 376

    Headphones operation the headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some headphone audio coverage to allow them to adjust the headphone volume for the young rear seat occupants that may not be able to do so for ...

  • Page 377

    Controls the headphone power indicator and controls are located on the right ear cup. Note: the rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video sys...

  • Page 378

    Replacing the batteries each set of headphones requires two aaa batteries for operation. To replace the batteries: • locate the battery compartment on the left ear cup of the headphones, and then slide the battery cover downward. • replace the batteries, making sure to orient them according to the p...

  • Page 379

    Nature whatsoever. Some states and jurisdictions may not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights. You may also have other rights, which vary from jurisdiction to jurisdiction...

  • Page 380

    Selected radio mode. When shared, the radio has priority over the ves™ or all radio modes (fm, am). The ves™ has the ability to switch tuner (am/fm), seek, scan, tune, and recall presets in radio modes as long as it is not in shared mode. When in shared disc both the radio and the ves™ have control ...

  • Page 381

    5. Channel 2 shared status 6. Channel 2 audio only/mute 7. Channel 1 enter button action 8. Channel 2 enter button action 9. Clock 10. Video lock 11. Not available / error 12. Disc changer status numeric keypad menu numeric keypad menu 4 understanding your instrument panel 379.

  • Page 382

    When the display for either channel 1 or channel 2 shows direct tune, pressing the remote control’s enter button activates a numeric keypad menu. This screen makes it easy to enter a specific tuner frequency, satellite channel, or track number. To enter the desired digit: 1. Press the remote control...

  • Page 383

    Disc menu when listening to a cd audio or cd data disc, pressing the remote control’s menu button displays a list of all commands which control playback of the disc. Using the options you can activate or cancel scan play and random play. Display settings when watching a video source (dvd video with ...

  • Page 384

    Settings are already set for optimum viewing, so there is no need to change these settings under normal circum- stances. To change the settings, press the remote control’s navi- gation buttons ( 䉱 , 䉲 ) to select an item, then press the remote control’s navigation buttons ( 䉴 , 䉳 ) to change the val...

  • Page 385

    Disc formats the ves™ dvd player is capable of playing the follow- ing types of discs (12 mm or 8 mm diameter): • dvd-video discs (mpeg-2 video compression) (see notes about dvd region codes) • dvd-audio discs (2 channel audio output only) • audio compact discs (cds) • cd data discs with mp3 and wma...

  • Page 386

    If you record a disc using a personal computer, there may be cases where the ves™ dvd player may not be able to play some or the entire disc, even if it is recorded in a compatible format and is playable on other players. To help avoid playback problems, use the following guide- lines when recording...

  • Page 387

    End with the extension ⬙ .Mp3 ⬙ or ⬙ .Mp3 ⬙ and wma files must always end with the extension ⬙ .Wma ⬙ or ⬙ .Wma ⬙ . To prevent incorrect playback, do not use these extensions for any other types of files. • for mp3 files, only version 1 id3 tag data (such as artist name, track title, album, etc.) ar...

  • Page 388

    If a disc has a damaged track which results in audible or visible errors that persists for 2.0 seconds, the dvd player will attempt to continue playing the disc by skipping forward 1.0 to 3.0 seconds at a time. If the end of the disc is reached, the dvd player will return to the beginning of the dis...

  • Page 389

    All of the language settings have a special ⬙ other ⬙ setting to accommodate languages other than japanese or eng- lish. These languages are selected using a special four- digit code. To enter a new language code, activate the dvd setup menu and follow these additional instructions: • using the remo...

  • Page 390

    Rating and password setup the rating and password settings work together to control the types of dvds that your family watches. Most dvd- video discs have a rating (from 1 to 8) assigned to them where lower numbers are designated for all audiences and higher numbers are designated for more adult aud...

  • Page 391

    To set the password, activate the dvd setup menu and follow these additional instructions: • using the remote control left and right cursor but- tons, select the rating tab. • highlight ⬙ change password ⬙ , and then press the remote control’s enter button. • enter the current password. Select a dig...

  • Page 392

    To set the rating, activate the dvd setup menu and follow these additional instructions: • using the remote control’s left and right cursor buttons, select the rating tab. • highlight ⬙ change rating ⬙ , and then press the remote control’s enter button. • enter the current password. Select a digit, ...

  • Page 393

    General information this system complies with part 15 of the fcc operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Harman kardon 姞 l...

  • Page 394

    Aux input; and is activated through the electronic vehicle information center (evic). Refer to “driver- selectable surround sound (dss)” under “electronic vehicle information center (evic)” in “understanding your instrument panel”. Selecting “audio surround” through the dss modes activates the harma...

  • Page 395

    The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will ...

  • Page 396

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 397

    Dual-zone automatic temperature control (atc) — if equipped • the automatic temperature control (atc) allows both driver and front passenger seat occupants to select individual comfort settings. • when occupants in the vehicle select an auto mode operation, auto blower operation is set by using a pu...

  • Page 398

    2. Recirculation control button press and release to change the current setting, the indicator illuminates when on. 3. Left front seat occupant temperature display this display shows the temperature setting for the left front seat occupant. 4. Mode display this display shows the current mode selecti...

  • Page 399

    11. Blower control there are seven blower speeds, the blower speed in- creases as you move the control to the right from the lowest blower setting. Performing this function will cause the atc to switch into manual mode. 12. Climate control on/off button press and release this button to turn the clim...

  • Page 400

    3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically. Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system auto...

  • Page 401

    Selected. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode. The operator can also select the direction of the airflow by selecting one of the following positions. Panel mode air comes from the outlets in the instrument panel. Each of the...

  • Page 402

    Defrost mode air comes from the windshield and side window demist outlets. Use defrost mode with maximum temperature settings for best windshield and side win- dow defrosting. When the defrost mode is selected, the blower will automatically default to medium-high unless the blower is controlled manu...

  • Page 403

    Recirculation control when outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by pressing the recirculation control button. Recirculation mode should only be used temporarily. The recirculation led will illuminate when this b...

  • Page 404

    Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Summer operation note: in some cases...

  • Page 405

    Operating tips chart 4 understanding your instrument panel 403.

  • Page 407: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 409 ▫ automatic transmission . . . . . . . . . . . . . . . 409 ▫ keyless enter-n-go . . . . . . . . . . . . . . . . . . . 410 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 411 ▫ extreme cold w...

  • Page 408

    ▫ active damping system . . . . . . . . . . . . . . . 428 䡵 driving through water . . . . . . . . . . . . . . . . . 428 ▫ flowing/rising water . . . . . . . . . . . . . . . . . 429 䡵 power steering . . . . . . . . . . . . . . . . . . . . . . . 431 䡵 parking brake . . . . . . . . . . . . . . . . . . ...

  • Page 409

    ▫ compact spare tire – if equipped . . . . . . . . 457 ▫ full size spare – if equipped . . . . . . . . . . . . 458 ▫ limited-use spare – if equipped . . . . . . . . . 459 ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . 460 ▫ tread wear indicators . . . . . . . . . . . . . . . . . 460 ▫...

  • Page 410

    䡵 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . 481 ▫ common towing definitions . . . . . . . . . . . . 482 ▫ trailer hitch classification . . . . . . . . . . . . . . 484 ▫ trailer towing weights (maximum trailer weight ratings) . . . . . . . . 485 ▫ trailer and tongue weight . . . ...

  • Page 411

    Starting procedures before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your ve...

  • Page 412

    Caution! (continued) • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle speed. • do not shift from reverse, park, or neutral into any forward gear when the engine is above idle speed. • before shifting into any gear, make sure your foot is fir...

  • Page 413

    2. Insert the engine start/stop button into the ignition switch with the lettering facing up and readable. 3. Press firmly on the center of the button to secure it into position. Removing the button 1. The engine start/stop button can be removed from the ignition switch for key fob use. 2. Insert th...

  • Page 414

    2. The ignition switch will return to the off position. 3. If the shift lever is not in park, the engine start/ stop button must be held for two seconds and vehicle speed must be above 5 mph (8 km/h) before the engine will shut off. The ignition switch position will remain in the acc position until ...

  • Page 415

    Extreme cold weather (below –20°f or ⫺ 29°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If engine fails to start warning! • never pour fuel or other flammable liquids into the ...

  • Page 416

    Clearing a flooded engine (using engine start/stop button) if the engine fails to start after you have followed the “normal starting” or “extreme cold weather ⬙ proce- dures, it may be flooded. To clear any excess fuel, press and hold the brake pedal, push the accelerator pedal all the way to the fl...

  • Page 417

    Automatic transmission caution! Damage to the automatic transmission may occur if the following precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at i...

  • Page 418

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, and remove the key fob. On...

  • Page 419

    Ignition when the ignition is in the lock/off position, and once removed the shift lever is locked in park. Brake/transmission shift interlock system this vehicle is equipped with a brake transmission shift interlock (btsi) system that holds the shift lever in the park position unless the brakes are...

  • Page 420

    Manual shifts can be made using the autostick 威 shift control (refer to “autostick 威 ” in this section). Pressing the shift paddles (-/+) while in the drive position, or tapping one of the steering wheel-mounted shift paddles (-/+), will manually select the transmission gear, and will display the cu...

  • Page 421

    Warning! (continued) • your vehicle could move and injure you and others if it is not completely in park. Check by trying to move the shift lever rearward (with the brake pedal released), after you have placed it in park. Make sure the transmission is in park before leaving the vehicle. • it is dang...

  • Page 422

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 423

    • with brake pedal released, verify that the shift lever will not move out of park. Reverse this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral use this range when the vehicle is standing for prolonged periods with engine runn...

  • Page 424

    When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading condi- tions, in hilly terrain, traveling into strong head winds, or while towing heavy trailers), use the “autostick 威 ” mode (refer to “autostick 威 ” in this section) to select a lower gear. Under th...

  • Page 425

    5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorize...

  • Page 426

    This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations. Operation when the shift lever is in the drive position, the trans- mission will operate automatically, shifting between the five av...

  • Page 427

    • the transmission will automatically downshift to first gear when coming to a stop. After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated. • you can start out in first or second gear. Tapping (+) (at a stop) will allow starting in second gear. Starting ...

  • Page 428

    Selec-track™ description selec-track™ combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance for all terrains. Selec-track™ consists of the following positions: • sport – dry weather, on-road calibration. Performance based tuning that provi...

  • Page 429

    • auto – fully automatic full time four-wheel drive operation can be used on and off road. Balances traction with seamless steering feel to provide im- proved handling and acceleration over two-wheel drive vehicles. The active suspension system will be in touring mode. • track – track road calibrati...

  • Page 430

    Active damping system this vehicle is equipped with an electronic controlled damping system. This system reduces body roll and pitch in many driving situations including cornering, accelera- tion and braking. There are 3 modes: • touring mode (available in terrain positions auto and snow) — used dur...

  • Page 431

    Flowing/rising water warning! Do not drive on, or cross, a road or a path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehic...

  • Page 432

    Caution! • driving through standing water may cause dam- age to your vehicle’s drivetrain components. Al- ways inspect your vehicle’s fluids (i.E., engine oil, transmission, axle, etc.) for signs of contamination (i.E., fluid that is milky or foamy in appearance) after driving through standing water...

  • Page 433

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 434

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the park position. The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully....

  • Page 435

    Note: • when the parking brake is applied and the transmis- sion is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that the park...

  • Page 436

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 437

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes the anti-lock brake system (abs), traction control system (tcs), brake assist system (bas), electronic roll mitigation (erm), and electronic stability control (esc). All five of th...

  • Page 438

    Differential (bld), functions similar to a limited-slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel...

  • Page 439

    Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicle speed are sufficient to potentially cause wheel lift...

  • Page 440

    Counteracting the oversteer or understeer condition. En- gine power may also be reduced to help the vehicle maintain the desired path. Esc uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not...

  • Page 441

    On this is the normal operating mode for esc. Whenever the vehicle is started, the esc system will be in this “on” mode. This mode should be used for most driving situations. Esc should only be turned to “partial off” mode for specific reasons as noted below. Partial off this mode is entered by mome...

  • Page 442

    Off” mode is overcome, turn esc back on by momen- tarily pressing the “esc off” switch. This may be done while the vehicle is in motion. Full off this mode is available in track mode only. Refer to “selec-terrain” in “starting and operating” for further information. In this mode, all tcs and esc sta...

  • Page 443

    Across an axle quite similarly to a limited slip differential. If one wheel on an axle is spinning faster than the other, the system will apply the brake of the spinning wheel and allow more engine torque to be applied to the wheel that is not spinning. To improve the vehicle’s traction when driving...

  • Page 444

    Warning! If tsc activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster ...

  • Page 445

    Note: • the “esc activation/malfunction indicator light” and the “esc off indicator light” come on momen- tarily each time the ignition switch is turned on. • each time the ignition is turned on, the esc system will be on even if it was turned off previously. • the esc system will make buzzing or cl...

  • Page 446

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 447

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ ....Blank.... ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t or s = temporary spare tire 31 = overall diameter in inches (in) 21...

  • Page 448

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 449

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 450

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 451

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Tire and loading information placard this placard tells you important information about the: ...

  • Page 452

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 453

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 454

    452 starting and operating.

  • Page 455

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 456

    Warning! (continued) • unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns...

  • Page 457

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage it. Inflation pressures specified on the placard are always cold tire inflation pressure. Cold tire inflation pressure...

  • Page 458

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 459

    Spare tire matching original equipped tire and wheel – if equipped your vehicle may be equivalent with a spare tire and wheel in look and function as the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehic...

  • Page 460

    Since this tire has limited tread life the original equip- ment tire should be repaired (or replaced) and reinstalled on your vehicle at the first opportunity. Note: the compact spare tire is to be used for rear wheel(s) only. For a flat front tire, move the rear tire to the front and use the compac...

  • Page 461

    Front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the temporary use full size spare tire needs to be replaced. Since it is not the same as your original equipment tire, replace (or repair) the original...

  • Page 462

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h). Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not ...

  • Page 463

    Life of tire the service life of a tire is dependent upon various factors including but not limited to: • driving style • tire pressure • distance driven warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result...

  • Page 464

    It is recommended you contact your original equipment or an authorized tire dealer with any questions you may have on tire specifications or capability. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. Warning! • do not use a tire, whee...

  • Page 465

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation ...

  • Page 466

    Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12°f (6.5°c). This means that when the outside...

  • Page 467

    For example, your vehicle has a recommended cold (parked for more than three hours) tire pressure of 33 psi (227 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressure is 28 psi (193 kpa), a tempera- ture drop to 20°f (-7°c) will decrease the tire pressure to approximately 24...

  • Page 468

    Note: • the tpms is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat ...

  • Page 469

    • various tire pressure monitoring system messages, which display in the electronic vehicle information center (evic), and a graphic displaying tire pressures • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will ill...

  • Page 470

    The system will automatically update, the graphic dis- play of the pressure value(s) will stop “flashing,” and the tire pressure monitoring telltale light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/...

  • Page 471

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, the ⬙ service tpm system ⬙ message will not be present, and a pressure value will be displayed...

  • Page 472

    Vehicle for up to 20 minutes above 15 mph (24 km/h), the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. In addition, the evic will display a “service tpm system ⬙ mes- sage for three seconds and then display dashes (- -) in place of the pressur...

  • Page 473

    Fuel requirements 6.4l engine the 6.4l engine is designed to meet all emissions regulations and provide excel- lent fuel economy and performance when using high-quality premium unleaded gasoline with an octane rating of 91 or higher. Light spark knock at low engine speeds is not harmful to your engi...

  • Page 474

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, mtbe, and etbe. Oxygen- ates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your ve...

  • Page 475

    To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to reset the engine controller memory more extensive repairs will be required for prolo...

  • Page 476

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition malfu...

  • Page 477

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 478

    1. Press the fuel filler door release switch (located under the headlamp switch). 2. Open the fuel filler door, and remove the fuel filler cap. Fuel filler door release switch fuel filler cap 476 starting and operating.

  • Page 479

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indi- cator light (mil)” to illuminate, due to f...

  • Page 480

    • tighten the gas cap about one-quarter turn until you hear one click. This is an indication that the cap is properly tightened. • if the gas cap is not tightened properly, the mil will come on. Be sure the gas cap is tightened every time the vehicle is refueled. Emergency fuel filler door release i...

  • Page 481

    In “understanding your instrument panel” for further information. Tighten the fuel filler cap properly and press the select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. Vehicle loading certification label as required by natio...

  • Page 482

    Springs, tires, or wheels). Heavier axles or suspension components, sometimes specified by purchasers for in- creased durability, does not necessarily increase the ve- hicle’s gvwr. Tire size the tire size on the label represents the actual tire size on your vehicle. Replacement tires must be equal ...

  • Page 483

    Until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving. Improper weight distributions can have an adverse affect on the way your vehicle steers and handles, and the way the brak...

  • Page 484

    Common towing definitions the following trailer towing related definitions will assist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load ...

  • Page 485

    Tongue weight (tw) the tongue weight is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal area the frontal area is the maximum height and ...

  • Page 486

    Warning! • an improperly adjusted weight-distributing hitch system may reduce handling, stability, braking performance, and could result in an accident. • weight-distributing hitch systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputabl...

  • Page 487

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 6.4l automatic...

  • Page 488

    Never exceed the maximum tongue weight stamped on your trailer hitch. Consider the following items when computing the weight on the front/rear axles of the vehicle: • the trailer tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weigh...

  • Page 489

    Towing requirements to promote proper break-in of your new vehicle drive- train components the following guidelines are recom- mended: caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, durin...

  • Page 490

    Warning! (continued) • safety chains must always be used between your vehicle and trailer. Always connect the chains to the hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parked on a gr...

  • Page 491

    − check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information” in “starting and operating” for proper inspection procedure. − when replacing tires, refer to “tires – general infor- mation” in “starting and operating” for proper tire replacement ...

  • Page 492

    Warning! • do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • towing any trailer will increase your stopping distance. When towing you should allow f...

  • Page 493

    Electronic speed control – if equipped − do not use in hilly terrain or with heavy loads. − when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − use speed control in flat terrain and with light loads to maxim...

  • Page 495: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . 494 䡵 if your engine overheats . . . . . . . . . . . . . . . . 494 䡵 jacking and tire changing . . . . . . . . . . . . . . . 495 ▫ run flat tires . . . . . . . . . . . . . . . . . . . . . . . 496 ▫ jack loca...

  • Page 496

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank just above the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. ...

  • Page 497

    Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads hot (h), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on hot (h), and you hear conti...

  • Page 498

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Run flat tires this vehicle is equipped with a compa...

  • Page 499

    Spare tire stowage the spare tire is stowed under the load floor in the rear cargo area and is secured to the body with a special wing nut. Preparations for jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery surfaces. Warning! Do not attempt to change a tire on the side of t...

  • Page 500

    6. Block both the front and rear of the wheel diagonally opposite of the jack- ing position. For example, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. 7. For vehicle equipped with quadra-lift 威 refer ...

  • Page 501

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. • only use the jack in the positions indicated and for lifting this vehicle during a tire change. • if working on or near a roadway, be extremely careful of motor tr...

  • Page 502

    3. Assemble the jack and jacking tools. Caution! Do not attempt to raise vehicle by jacking on loca- tions other than those indicated in the jacking in- structions for this vehicle. Jack and tool assembly jacking locations 500 what to do in emergencies.

  • Page 503

    4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do not raise the vehicle until you are sure the jack is fully engaged. Lift point symbol on sill molding front jacking location 6 what to do in em...

  • Page 504

    5. For a rear tire, place the jack in the slot on the rear tie-down bracket, just forward of the rear tire (as indi- cated by the triangular lift point symbol on the sill molding). Do not raise the vehicle until you are sure the jack is fully engaged. 6. Raise the vehicle by turning the jack screw c...

  • Page 505

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 7. Remove the lug nuts and wheel. 8. Position the spare wheel/tire on the vehicle and install the lug nuts with ...

  • Page 506

    9. Lower the vehicle by turning the jack screw counter- clockwise, and remove the jack and wheel blocks. 10. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. ...

  • Page 507

    Warning! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Road tire installation 1. Mount the road tire...

  • Page 508

    Note: when using a portable battery booster pack follow the manufacturer’s operating instructions and precautions. Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electr...

  • Page 509

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

  • Page 510

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) j...

  • Page 511

    8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the remote positive (+) post of the discharged vehicle. 10. Reinstall the protective cover over the remote posi- tive (+) bat...

  • Page 512

    Caution! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the en- gine to idle with the shift lever in neutral for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure du...

  • Page 513

    Emergency tow hooks — if equipped if your vehicle is equipped with tow hooks, there will be one in the rear and two mounted on the front of the vehicle. The rear hook will be located on the driver’s side of the vehicle. Note: for off-road recovery, it is recommended to use both of the front tow hook...

  • Page 514

    4. Using a screwdriver or similar tool, carefully remove the shift lever override access cover, located on the bottom of the cupholder. 5. Press and maintain firm pressure on the brake pedal. 6. Using the screwdriver or similar tool, press and hold the shift lock lever down. 7. Move the shift lever ...

  • Page 515: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 6.4l . . . . . . . . . . . . . 515 䡵 onboard diagnostic system – obd ii . . . . . . . 516 ▫ loose fuel filler cap message . . . . . . . . . . . 516 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 516

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 539 ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . 541 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . 542 ▫ automatic transmission . . . . . . . . . . . . . . . 543 ▫ appearance care and protection from corrosion ...

  • Page 517

    Engine compartment — 6.4l 1 — totally integrated power module (fuses) 6 — air cleaner filter 2 — engine oil dipstick 7 — power steering fluid reservoir 3 — engine oil fill 8 — coolant pressure cap (radiator) 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — washer fluid reservoir 7 maintain...

  • Page 518

    Onboard diagnostic system – obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 519

    The select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the malfunction indicator light (mil). Emissions inspection and maintenance programs in some l...

  • Page 520

    4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 521

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 522

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 523

    Caution! (continued) • operating the engine with the oil levels below the safe zone, or operating with oil levels that exceed the top of the safe zone may cause engine damage. Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled main...

  • Page 524

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity sae 0w-40 engine oil is preferred for use in all operating temperatures. The engine oil filler cap also shows the reco...

  • Page 525

    Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection the manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only hi...

  • Page 526

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Caution! • do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the ...

  • Page 527

    Warning! (continued) • batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive. Keep open flames or sparks away from the battery. • do not allow vehicles to touch each other as this could establish a ground connection and personal in...

  • Page 528

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 529

    The a/c air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to re- place the filter: 1. Open the glove compartment and remove all contents. 2. Push in on the sides of the glove compartment and lower the door. 3. Pivot the glove compartment downward. 4. ...

  • Page 530

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 7. Rotate the glove compartment door back into position. Body lubrication locks and all body pivot points...

  • Page 531

    Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Note: life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may ...

  • Page 532

    3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. 4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade an...

  • Page 533

    When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperat...

  • Page 534

    Caution! The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- ness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. Under normal operating conditions, the catalyti...

  • Page 535

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situati...

  • Page 536

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot eng...

  • Page 537

    Cooling system – drain, flush, and refill if the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant...

  • Page 538

    Adding coolant your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to 5 years or 102,000 miles (170 000 km) before replace- ment. To prevent reducing this extended maintenance period, it ...

  • Page 539

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign mat...

  • Page 540

    Disposal of used engine coolant used ethylene glycol based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol...

  • Page 541

    If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • do not overfill the coolant recovery bottle. • check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottl...

  • Page 542

    Disc brakes, fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. If the brake fluid level is abnormally low, check system for leaks. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further informat...

  • Page 543

    Warning! (continued) • do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident. Front/rear axle fluid for normal service, periodic fluid level checks are not required. Whe...

  • Page 544

    Caution! Do not over tighten the plugs as it could damage then and cause them to leak. Selection of lubricant use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintain- ing your vehicle” for further information. Transfer case fluid level check inspe...

  • Page 545

    Automatic transmission selection of lubricant it is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only the manufacturer’s recommended trans- mission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicl...

  • Page 546

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check regular automatic transmission fluid level checks are not required. For this reason the dipstick is ...

  • Page 547

    The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road...

  • Page 548

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty...

  • Page 549

    Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • to remove heavy soil and/or excessive brake dust, use mopar 威 wheel cleaner or equivalent or select a non-abrasive, non-...

  • Page 550

    Interior care use mopar 威 total clean or equivalent to clean fabric upholstery and carpeting. Interior trim should be cleaned starting with a damp cloth, a damp cloth with mopar 威 total clean or equiva- lent, then mopar 威 spot & stain remover or equivalent if absolutely necessary. Do not use harsh c...

  • Page 551

    When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be...

  • Page 552

    Fuses totally integrated power module the totally integrated power module is located in the engine compartment. This center contains cartridge fuses and mini fuses. A description of each fuse and compo- nent may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on t...

  • Page 553

    Cavity cartridge fuse mini fuse description j03 30 amp pink trailer tow j04 25 amp natural driver door node j05 25 amp natural passenger door node j06 40 amp green antilock brakes pump/stability control system j07 30 amp pink antilock brakes valve/stability control system j08 40 amp green power seat...

  • Page 554

    Cavity cartridge fuse mini fuse description j18 20 amp blue powertrain control module/powertrain control module transmission range j19 60 amp yellow radiator fan motor hi/radiator fan motor low j20 30 amp pink front wiper j21 20 amp blue front/rear washer control j22 25 amp natural sunroof module m1...

  • Page 555

    Cavity cartridge fuse mini fuse description m10 15 amp blue video/universal garage door opener m11 10 amp red heating, ventilation & air conditioning (climate control system) m12 30 amp green radio/amplifier m13 20 amp yellow instrument cluster m14 20 amp yellow back up camera – if equipped cavity c...

  • Page 556

    Cavity cartridge fuse mini fuse description m21 20 amp yellow automatic shutdown 3 m22 10 amp red horns (low/high) – right m23 10 amp red horns (low/high) – left m24 25 amp natural rear wiper m25 20 amp yellow fuel pump motor output/diesel lift pump (export only) m26 10 amp red driver door switch ba...

  • Page 557

    Cavity cartridge fuse mini fuse description m34 10 amp red park assist module/ climate control system module/infra red sensor/compass module m35 15 amp blue left rear parklamps m36 20 amp yellow power outlet m37 10 amp red antilock brakes/ stability control system module m38 25 amp natural all door ...

  • Page 558

    Vehicle storage if you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • remove fuse #j13 in the totally integrated power module (tipm) labeled ignition-off draw (iod#1). • or, disconnect the negative cable from the battery. • anyti...

  • Page 559

    Exterior lights bulb type headlamps (low beam) . . . . . . . . . . . . . . . . . . . H11 headlamps (high beam) . . . . . . . . . . . . . . . . . . 9005 headlamps (low beam) – high intensity discharge (hid) . . . . . . . . . . . . . . . . . . . . . . . . . D1s (serviced at authorized dealer) front pa...

  • Page 560

    Note: on vehicles equipped with high intensity dis- charge (hid) headlamps, when the headlamps are turned on, there is a blue hue to the lamps. This dimin- ishes and becomes more white after approximately 10 seconds, as the system charges. Halogen headlamps – if equipped 1. Open the hood. 2. Turn th...

  • Page 561

    2. Firmly grasp the bulb by the two latches and squeeze them together to unlock the bulb from the back of the front fog lamp housing. 3. Pull the bulb straight out from the keyed opening in the housing. Caution! • do not touch the new bulb with your fingers. Oil contamination will severely shorten b...

  • Page 562

    Rear tail, stop, turn signal, and backup lamps 1. Raise the liftgate. 2. Remove the two push-pins from the tail lamp housing. 3. Grasp the tail lamp and pull firmly rearward to disengage the lamp from the aperture panel. 4. Twist socket counter clockwise and remove from lamp. 5. Pull the bulb to rem...

  • Page 563

    8. Continue removing the trim. 9. Disconnect the two trim panel lights. 10. Tail lamps are now visible. Rotate socket(s) counter clockwise. 11. Remove/replace bulb(s). 12. Reinstall the socket(s) 13. Reverse process to reinstall the liftgate trim. Center high-mounted stop lamp (chmsl) the center hig...

  • Page 564

    Rear license lamp 1. Use a screw driver to gently pry against the side of the snap tab to remove the license lamp lens. 2. Pull bulb from socket. 3. Replace bulb. 4. Reinstall lens. Fluid capacities u.S. Metric fuel (approximate) 25 gallons 94 liters engine oil with filter 6.4 liter engine (sae 0w-4...

  • Page 565

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) or equivalent. Engine oil for best performance and maximum protection under all types of operating ...

  • Page 566

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 威 automatic transmission fluid or equivalent licensed atf+4 威 product. Transfer case mopar 威 nv146 transfer case fluid or equivalent. Usage of other fluid/lubricants is not recommended. Axle differential (front-...

  • Page 567: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedules . . . . . . . . . . . . . . . . . 566 ▫ required maintenance intervals . . . . . . . . . . 567 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 568

    Maintenance schedules the scheduled maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditio...

  • Page 569

    Referring to the steps described under “electronic vehicle information center (evic)/oil change required” in “understanding your instrument panel” for further in- formation. At each stop for fuel • check the engine oil level about five minutes after a fully warmed engine is shut off. Checking the oi...

  • Page 570

    6,000 miles (10,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. Odometer reading date repair order # dealer code signature, authorized service center 12,000 miles (20,000 km) or 12 months maintenance service schedule ❏ change the engine oil and engine ...

  • Page 571

    18,000 miles (30,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. Odometer reading date repair order # dealer code signature, authorized service center 24,000 miles (40,000 km) or 24 months maintenance service schedule ❏ change the engine oil and engin...

  • Page 572

    30,000 miles (50,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ replace the engine air cleaner filter. ❏ drain the transfer case and refill. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. Odometer reading date repair order...

  • Page 573

    42,000 miles (70,000 km) or 42 months maintenance service schedule ❏ change the engine oil and engine oil filter. Odometer reading date repair order # dealer code signature, authorized service center 48,000 miles (80,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engin...

  • Page 574

    54,000 miles (90,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. Odometer reading date repair order # dealer code signature, authorized service center 60,000 miles (100,000 km) or 60 months maintenance service schedule ❏ change the engine oil and engi...

  • Page 575

    66,000 miles (110,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. Odometer reading date repair order # dealer code signature, authorized service center 72,000 miles (120,000 km) or 72 months maintenance service schedule ❏ change the engine oil and eng...

  • Page 576

    78,000 miles (130,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. Odometer reading date repair order # dealer code signature, authorized service center 84,000 miles (140,000 km) or 84 months maintenance service schedule ❏ change the engine oil and eng...

  • Page 577

    90,000 miles (150,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ replace the engine air cleaner filter. ❏ inspect and replace pcv valve if necessary. ❏ drain the transfer case and refill. ❏ adjust parking brake on vehicles equipped with four-wheel ...

  • Page 578

    102,000 miles (170,000 km) or 102 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ flush and replace the engine coolant at 102,000 miles (170 000 km) or 60 months whichever comes first. Odometer reading date repair order # dealer code signature, authorized service...

  • Page 579

    114,000 miles (190,000 km) or 114 months maintenance service schedule ❏ change the engine oil and engine oil filter. Odometer reading date repair order # dealer code signature, authorized service center 120,000 miles (200,000 km) or 120 months maintenance service schedule ❏ change the engine oil and...

  • Page 580

    126,000 miles (210,000 km) or 126 months maintenance service schedule ❏ change the engine oil and engine oil filter. Odometer reading date repair order # dealer code signature, authorized service center 132,000 miles (220,000 km) or 132 months maintenance service schedule ❏ change the engine oil and...

  • Page 581

    138,000 miles (230,000 km) or 138 months maintenance service schedule ❏ change the engine oil and engine oil filter. Odometer reading date repair order # dealer code signature, authorized service center 144,000 miles (240,000 km) or 144 months maintenance service schedule ❏ change the engine oil and...

  • Page 582

    150,000 miles (250,000 km) or 150 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ replace the engine air cleaner filter. ❏ drain the transfer case and refill. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. Odometer reading date repair or...

  • Page 583

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • failure to properly inspect and mai...

  • Page 585: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585 ▫ prepare for the appointment . . . . . . . . . . . 585 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 585 ▫ be reasonable with r...

  • Page 586

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 591 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 591 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 591 ▫ temperature grades . . . . . . . . . . . . . . . . . . 59...

  • Page 587

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 588

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 589

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 590

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 591

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 592

    • service manuals these comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group llc vehicles. A complete working knowledge of the vehicle, system, and/or...

  • Page 593

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 594

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 595: Index

    Index 10

  • Page 596

    Adaptive cruise control (acc) (cruise control) . . 196 adding engine coolant (antifreeze) . . . . . . . . . . 536 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 475 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . 473 air conditioner maintenance . . . . . . . . . ...

  • Page 597

    Auxiliary electrical outlet (power outlet) . . . . . . 254 auxiliary power outlet . . . . . . . . . . . . . . . . . . . 254 b-pillar location . . . . . . . . . . . . . . . . . . . . . . . . 449 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524 keyless transmitter replacement ...

  • Page 598

    Center high mounted stop light . . . . . . . . . . . . 561 certification label . . . . . . . . . . . . . . . . . . . . . . . 479 chart, tire sizing . . . . . . . . . . . . . . . . . . . . . . . . 445 check engine light (malfunction indicator light) . . . . . . . . . . . . . . . 517 checking your veh...

  • Page 599

    Radiator cap . . . . . . . . . . . . . . . . . . . . . . . 537 selection of coolant (antifreeze) . . . . . . . 535,562 cruise control (speed control) . . . . . . . . . . . . . . 196 cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 customer assistance . . . . . . . . . . . . . ....

  • Page 600

    Emergency, in case of freeing vehicle when stuck . . . . . . . . . . . . . 509 hazard warning flasher . . . . . . . . . . . . . . . 494 jump starting . . . . . . . . . . . . . . . . . . . . . . . 505 tow hooks . . . . . . . . . . . . . . . . . . . . . . . . . 511 emission control system maintenance ...

  • Page 601

    Filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . 523 air conditioning . . . . . . . . . . . . . . . . . . . . . 526 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . 523 engine oil disposal . . . . . . . . . . . . . . . . . . . 522 finish care . . . . . . . . . . . . ...

  • Page 602

    Requirements . . . . . . . . . . . . . . . . . . . . 471,562 saver mode . . . . . . . . . . . . . . . . . . . . . . . . 307 tank capacity . . . . . . . . . . . . . . . . . . . . . . . 562 fuel optimizer . . . . . . . . . . . . . . . . . . . . . . . . . 307 fuel saver . . . . . . . . . . . . . . . . ...

  • Page 603

    Hill descent control indicator . . . . . . . . . . . . . . . 283 hitches trailer towing . . . . . . . . . . . . . . . . . . . . . . . 484 holder, cup . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 homelink® (garage door opener) transmitter . . 238 hood release . . . . . . . . . . . . . . ...

  • Page 604

    Lap/shoulder belts . . . . . . . . . . . . . . . . . . . . . . . 51 latch (lower anchors and tether for children) . . . . . 84,86 latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 lead free gasoline . . . . . . . . . . . . . . . . . . . . . . 471 leaks, fluid . . . . . . . ....

  • Page 605

    Rear tail . . . . . . . . . . . . . . . . . . . . . . . . . . . 560 seat belt reminder . . . . . . . . . . . . . . . . . . . 286 security alarm (theft alarm) . . . . . . . . . . . . 289 service . . . . . . . . . . . . . . . . . . . . . . . . . . . . 557 service engine soon (malfunction indicator) . ...

  • Page 606

    Electric remote . . . . . . . . . . . . . . . . . . . . . . 107 exterior folding . . . . . . . . . . . . . . . . . . . . . 107 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 outside . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 vanity . . . . . . . . . . . . . . . . ....

  • Page 607

    Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423 overdrive off switch . . . . . . . . . . . . . . . . . . . . 423 overhead console . . . . . . . . . . . . . . . . . . . . . . . 236 overheating, engine . . . . . . . . . . . . . . . . . . . 290,494 owner’s manual (operator manua...

  • Page 608

    Radial ply tires . . . . . . . . . . . . . . . . . . . . . . . . . 456 radiator cap (coolant pressure cap) . . . . . . . . . . 537 radio operation . . . . . . . . . . . . . . . . . . . . . . . . 394 rain sensitive wiper system . . . . . . . . . . . . . . . . 188 rear axle (differential) . . . . . . ...

  • Page 609

    Safety information, tire . . . . . . . . . . . . . . . . . . . 443 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 safety, exhaust gas . . . . . . . . . . . . . . . . . . . . . 47,95 satellite radio antenna . . . . . . . . . . . . . . . . . . . 348 schedule, maintenance . . ...

  • Page 610

    Service engine soon light (malfunction indicator) . . . . . . . . . . . . . . . . . . . . 281 service manuals . . . . . . . . . . . . . . . . . . . . . . . . 589 setting the clock . . . . . . . . . . . . . . . . . . . . . 328,337 settings, personal . . . . . . . . . . . . . . . . . . . . . . . . 318...

  • Page 611

    Sun visor extension . . . . . . . . . . . . . . . . . . . . . . 109 sunglasses storage . . . . . . . . . . . . . . . . . . . . . . . 238 supplemental restraint system - airbag . . . . . . . . 65 sway control, trailer . . . . . . . . . . . . . . . . . . . . . 441 system, remote starting . . . . . . ....

  • Page 612

    Tongue weight/trailer weight . . . . . . . . . . . . . . 485 tow hooks, emergency . . . . . . . . . . . . . . . . . . . 511 tow/haul indicator light . . . . . . . . . . . . . . . . . 283 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 481,512 24-hour towing assistance . . . . . . . . ...

  • Page 613

    Universal consumer interface (uci) connector . . . 351 universal transmitter . . . . . . . . . . . . . . . . . . . . . 238 unleaded gasoline . . . . . . . . . . . . . . . . . . . . . . . 471 untwisting procedure, seat belt . . . . . . . . . . . . . . 56 upholstery care . . . . . . . . . . . . . . . ...

  • Page 614

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 615

    Chrysler group llc 12 wk742-126 - ad -r 4th edition p rinted in u.S.A..