1. DL manuals
  2. Jeep
  3. Scooter
  4. Grand Cherokee
  5. Owner's Manual

Jeep Grand Cherokee Owner's Manual

Manual is about: 2015

Summary of Grand Cherokee

  • Page 1

    Grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2 0 12 g ra n d c h e ro k e e 12wk741-126-aa first edition printed in u.S.A. 2 0 1 2 907713 jeep cherokee om cover.Indd 1 3/10/11 1:09 pm.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 5 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 7 䡵 vehicle ide...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the unive...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ wireless ignition node (win) . . . . . . . . . . . . 12 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ removing key fob from ignition . . . . . . . . . . 14 ▫ ...

  • Page 12

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . 24 ▫ programming additional transmitters . . . . . . 25 ▫ transmitter battery replacement . . . . . . . . . . 25 ▫ general information . . . . . . . . . . . . . . . . . . . 27 䡵 remote starting system — if equipped . . . . . . . 27 ▫ how to u...

  • Page 13

    ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . 59 ▫ supplemental active head restraints (ahr) . . 59 ▫ enhanced seat belt use reminder system (beltalert 威 ) . . . . . . . . . . . . . . . . . . . . . . . . . 63 ▫ seat belt lock out . . . . . . . . . . . . . . . . . . . . 64 ▫ seat belts ...

  • Page 14

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a wireless ignition node (win) with integral ignition switch. You can insert the key fob into the ignition switch with either side up. Keyless enter-n...

  • Page 15

    Key fob the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key ...

  • Page 16

    To remove the emergency key, slide the mechanical latch at the top of the key fob sideways with your thumb and then pull the key out with your other hand. Note: you can insert the double-sided emergency key into the lock cylinders with either side up. Removing key fob from ignition place the shift l...

  • Page 17

    • the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the off position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “electronic vehi...

  • Page 18

    Warning! (continued) • do not leave the key fob in or near the vehicle, and do not leave keyless enter-n-go in the acc or on/run mode. A child could operate power win- dows, other controls, or move the vehicle. • do not leave children or animals inside parked vehicles in hot weather. Interior heat b...

  • Page 19

    Sentry key 姞 the sentry key 威 immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses the factory-mated key fob with remot...

  • Page 20

    Replacement keys note: only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle. Caution! • always remove the key fobs from the vehicle and lock all doors when le...

  • Page 21

    • this device must accept any interference that may be received, including interference that may cause unde- sired operation. Vehicle security alarm — if equipped this vehicle security alarm monitors the vehicle doors, liftgate, liftgate flipper glass, and ignition for unauthor- ized operation. When...

  • Page 22

    • for vehicles not equipped with keyless enter-n-go, make sure the vehicle ignition system is ⬙ off ⬙ and the key is physically removed from the ignition. 2. Perform one of the following methods to lock the vehicle: • press lock on the interior power door lock switch with the driver and/or passenger...

  • Page 23

    Note: • the driver’s door key cylinder and the liftgate button on the rke transmitter cannot arm or disarm the vehicle security alarm. • the vehicle security alarm remains armed during power liftgate entry. Pressing the liftgate button will not disarm the vehicle security alarm. If someone enters th...

  • Page 24

    This feature also turns on the approach lighting in the outside mirrors (if equipped). Refer to “mirrors” in “understanding the features of your vehicle” for fur- ther information. The lights will fade to off after approximately 30 seconds or they will immediately fade to off once the ignition switc...

  • Page 25

    To unlock the doors press and release the unlock button on the rke transmitter once to unlock the driver’s door or twice to unlock all doors. The turn signal lamps will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Refer to “keyless enter-n-go” under “things...

  • Page 26

    Illuminated approach this feature activates the headlights for up to 90 seconds when the doors are unlocked with the rke transmitter. The time for this feature is programmable on vehicles equipped with the electronic vehicle information center (evic). Refer to “electronic vehicle information center ...

  • Page 27

    Note: the interior lights will turn off if you turn the ignition switch to the acc or on/run position while the panic alarm is activated. However, the exterior lamps and horn will remain on. Programming additional transmitters programming key fobs or rke transmitters may be performed at an authorize...

  • Page 28

    2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. 3. Remove and replace the battery. When replacing the battery, match the + sign on the battery to the + sig...

  • Page 29

    4. To assemble the rke transmitter case, snap the two halves together. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept ...

  • Page 30

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • liftgate/flipper glass closed • hazard switch off • brake switch inactive (brake pedal not pressed) • ignition key removed from ignition switc...

  • Page 31

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 32

    • the engine can be started two consecutive times with the rke transmitter. However, the ignition must be cycled by pushing the start/stop button twice (or the ignition switch must be cycled to the on/run position) before you can repeat the start sequence for a third cycle. To exit remote start mode...

  • Page 33

    Remote start comfort systems — if equipped when remote start is activated, the heated steering wheel, and driver heated seat features will automatically turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These featu...

  • Page 34

    Warning! • for personal security and safety in the event of an accident, lock the vehicle doors when you drive, as well as when you park and leave the vehicle. • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or...

  • Page 35

    If you press the door lock switch while the key fob is in the ignition switch and the driver’s door is open, the doors will not lock. If a rear door is locked, it cannot be opened from inside the vehicle without first unlocking the door. The door may be unlocked manually by raising the lock knob. Au...

  • Page 36

    3. Repeat steps 1 and 2 for the opposite rear door. Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged (locked). Child-protection door lock location child-protection door lock functi...

  • Page 37

    Note: for emergency exit from the rear seats when the child-protection door lock system is engaged, manually raise the door lock knob to the unlocked position, roll down the window, and open the door using the outside door handle. Keyless enter-n-go the passive entry system is an enhancement to the ...

  • Page 38

    To unlock from the driver’s side: with a valid passive entry rke transmitter within 5 ft (1.5 m) of the driver’s door handle, grab the driver’s front door handle to unlock the driver’s door automatically. The interior door panel lock knob will raise when the door is unlocked. Note: if “unlock all do...

  • Page 39

    Preventing inadvertent locking of passive entry rke transmitter in vehicle to minimize the possibility of unintentionally locking a passive entry rke transmitter inside your vehicle, the passive entry system is equipped with an automatic door unlock feature which will function if there is no key fob...

  • Page 40

    Note: if “unlock all doors 1st press” is programmed in evic, all doors will unlock when you push the button on the liftgate. If ⬙ unlock driver door 1st press ⬙ is programmed in evic, the liftgate and flipper glass will unlock when you press the button on the liftgate for further information, refer ...

  • Page 41

    Note: • after pressing the door handle lock button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • the pas...

  • Page 42

    Warning! Never leave children in a vehicle with the key in the ignition switch or leave a vehicle with keyless enter- n-go in the acc or on/run position. Occupants, particularly unattended children, can become en- trapped by the windows while operating the power window switches. Such entrapment may ...

  • Page 43

    During auto up. If this happens, pull the switch lightly to the first detent and hold it to close the window manually. Warning! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Resetting the auto up feature should the au...

  • Page 44

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 45

    Liftgate flipper glass the liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. Note: the liftgate flipper glass will not open if the liftgate is ajar. Once the liftgate flipper glass has been opened, ...

  • Page 46

    Power liftgate — if equipped the power liftgate may be opened by pulling up on the liftgate handle or by pressing the liftgate button on the remote keyless entry (rke) transmitter. Press the liftgate button on the rke transmitter twice within five seconds, to open the power liftgate. Once the liftga...

  • Page 47

    Warning! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. • the power liftgate will not operate if the liftgate flipper glass is open. • the power liftgate buttons will not o...

  • Page 48

    • if the liftgate handle is pulled while the power liftgate is opening, the liftgate motor will disengage to allow manual operation. • if the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and the liftgate must be opened or closed manu- ally...

  • Page 49

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belts for the driver and all passengers • advanced front air bags for driver and front passen- ger • supplemental active head restraints (ahr) located on top of th...

  • Page 50

    Infant and child restraint systems. For more information on latch, refer to lower anchors and tether for children (latch). Note: the advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severit...

  • Page 51

    3. The driver and front passenger seats should be moved back as far as practical to allow the advanced front air bags room to inflate. 4. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between...

  • Page 52

    Warning! (continued) • supplemental side air bag inflatable curtain (sabic) and seat-mounted side air bags (sab) also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • in a collision, you and your passengers can suffer much greater injuries if you...

  • Page 53

    Warning! • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much wo...

  • Page 54

    2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “cli...

  • Page 55

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you properly. In a sudden stop...

  • Page 56

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. Wa...

  • Page 57

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. In...

  • Page 58

    Adjustable upper shoulder belt anchorage in the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Press the release button to release the anchorage, and then move it up or down to the position that fits you best. As a guide, if yo...

  • Page 59

    Seat belts in passenger seating positions the seat belts in the passenger seating positions are equipped with automatic locking retractors (alr) which are used to secure a child restraint system. For additional information, refer to “installing child re- straints using the vehicle seat belt” under t...

  • Page 60

    Position that has a belt with this feature. Children 12 years old and under should always be properly restrained in the rear seat. How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extrac...

  • Page 61

    Seat belt pretensioners the seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by assuring that the belt is tight about the oc...

  • Page 62

    However if during a front impact, a secondary rear impact occurs, the ahr may deploy based on several factors, including the severity and type of the impact. Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed i...

  • Page 63

    1. Grasp the deployed ahr from the rear seat. 2. Position the hands on the top of the deployed ahr at a comfortable position. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand positioning points on ahr 1 — downward movement 2 — rearward moveme...

  • Page 64

    4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an autho...

  • Page 65

    Enhanced seat belt use reminder system (beltalert 姞 ) beltalert 威 is a feature intended to remind the driver and front passenger (if equipped with front passenger beltalert 威 ) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unb...

  • Page 66

    Seat belt lock out the center rear seat belt system has a lock out feature that will not allow you to extract the center webbing unless the rear seat upper latch is engaged. Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the moth...

  • Page 67

    Instrument panel, above the glove compartment. The words srs airbag are embossed on the air bag covers. Note: the driver and front passenger advanced front air bags are certified to the new federal regulations for advanced air bags. The advanced front air bags have a multistage inflator design. This...

  • Page 68

    This vehicle is equipped with supplemental side air bag inflatable curtains (sabic) to protect the driver, front, and rear passengers sitting next to a window. The sabic air bags, are located above the side windows and their covers are also labeled: srs airbag. This vehicle is equipped with suppleme...

  • Page 69

    • front seat belt pretensioners, seat belt buckle switch, and seat track position sensors advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined ...

  • Page 70

    Supplemental seat-mounted side air bags (sab) supplemental seat-mounted side air bags (sab) may provide enhanced protection to help protect an occupant during a side impact. The sab is marked with an air bag label sewn into the outboard side of the front seats. When the air bag deploys, it opens the...

  • Page 71

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the sab and sabic air bags during deployment could cause you to be severely injured or killed. • should a vehicle rollover occur, the pretensioners and/or sab and sabic ...

  • Page 72

    Warning! (continued) • do not use accessory seat covers or place objects between you and the side air bags; the perfor- mance could be adversely affected and/or objects could be pushed into you, causing serious injury. • if your vehicle is equipped with sabic air bags, do not have any accessory item...

  • Page 73

    Advanced front air bags are designed to provide addi- tional protection by supplementing the seat belts in certain frontal collisions depending on the severity and type of collision. Advanced front air bags are not expected to reduce the risk of injury in rear, side, or rollover collisions. The adva...

  • Page 74

    Also, the orc turns on the air bag warning light in the instrument panel for approxi- mately four to eight seconds for a self-check when the ignition is first turned on. After the self-check, the air bag warning light will turn off. If the orc detects a malfunction in any part of the system, it turn...

  • Page 75

    Are possible, based on the collision type and severity. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The air bags fully inflate in about 50 to 70 milliseconds. This is about half of the...

  • Page 76

    A quantity of non-toxic gas is generated to inflate the sabic. The inflating sabic pushes the outside edge of the headliner out of the way and covers the window. The sabic inflates in about 30 milliseconds (about one- quarter of the time that it takes to blink your eyes) with enough force to injure ...

  • Page 77

    • unlock the doors automatically. In order to reset the enhanced accident response system functions after an event, the ignition switch must be changed from ign on to ign off. If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or ...

  • Page 78

    Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retrac- tor assemblies replaced by an authorized dealer im- mediately. Also, have the occupant restraint con- troller (orc) system servi...

  • Page 79

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, includ- ing your trim cover and cushio...

  • Page 80

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of t...

  • Page 81

    In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. Child restraints everyone in your vehicle needs to be buckled up all the time, including babies and children. Ev...

  • Page 82

    Facing child safety seat. Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. The infant carrier is only used rearward-facing in the vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrie...

  • Page 83

    Here are some tips for getting the most out of your child restraint: • before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. Chrysler group llc also recommends that you try a child restraint in the vehicle seats where you will use...

  • Page 84

    Note: for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck. Cana- dian residents should refer to transport canada’s web- site for additional information: http://www.Tc.Gc.Ca/ roadsafety/safedrivers/childsafety/index.Htm older children and child restraints children who are t...

  • Page 85

    • if the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind the back. Lower anchors and tether for children (latch) your vehicle’s rear seat is equipped with the child restraint anchorage sy...

  • Page 86

    The rear outboard seating positions have lower anchorages capable of accommodating latch- compatible child seats having flexible, webbing-mounted lower attachments and child seats with fixed lower attachments. The rear seat lower anchors can be readily identified by the symbol located on the seatbac...

  • Page 87

    In addition, there are top tether strap anchorages behind each rear seating position located on the back of the seat. To access the top tether strap anchorages behind the rear seat, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchorages. Latch anchora...

  • Page 88

    Warning! Do not use the cargo tie downs located on the load floor. Improper usage of the tether can lead to a failure of an infant or child restraint. The child could be badly injured or killed. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having...

  • Page 89

    Gap panel. They are not visible until you fold the gap panel down. Do not use the cargo tie down hooks located on the floor behind the seat. Finally, tighten all three straps as you push the child restraint rearward and downward into the seat, removing slack in the straps according to the child rest...

  • Page 90

    Installing a child restraint with an alr: 1. To install a child restraint with alr, first, pull enough of the seat belt webbing from the retractor to route it through the belt path of the child restraint. Slide the latch plate into the buckle until you hear a “click.” next, extract all the seat belt...

  • Page 91

    For center seating position route the tether strap over the seatback and headrest then attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, route the tether under the head re- straints, and attach the hook to the top tether anchor located on the b...

  • Page 92

    Top tether strap anchorage (located on seatback) top tether strap mounting 90 things to know before starting your vehicle.

  • Page 93

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly be- hind the child seat to secure a child restraint top tether strap. • do not use the cargo tie downs located on the load floor. Improper usag...

  • Page 94

    While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. However, wide-open throttle acceleration in low gear can be detrimental and should be avoided. The engine oil, transmission fluid, and axle lubricant installed at the factory is h...

  • Page 95

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), whi...

  • Page 96

    Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, ...

  • Page 97

    Floor mat safety information always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in o...

  • Page 98

    Warning! (continued) • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • if required, mounting posts must be properly installed, if not equipped...

  • Page 99: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 ▫ automatic dimming mirror . . . . . . . . . . . . . 104 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . 105 ▫ outside mirrors folding feature . . . . . . . . . 105...

  • Page 100

    ▫ things you should know about your uconnect™ phone . . . . . . . . . . . . . . . . . . . . 135 ▫ general information . . . . . . . . . . . . . . . . . . 146 䡵 voice command — if equipped . . . . . . . . . . . 146 ▫ voice command system operation . . . . . . . . 146 ▫ commands . . . . . . . . . . . ...

  • Page 101

    ▫ to disable a rke transmitter linked to memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 ▫ easy entry/exit seat . . . . . . . . . . . . . . . . . . 172 䡵 to open and close the hood . . . . . . . . . . . . 173 䡵 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 ▫ h...

  • Page 102

    ▫ intermittent wiper system . . . . . . . . . . . . . . 184 ▫ windshield washer operation . . . . . . . . . . . 185 ▫ mist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 ▫ rain sensing wipers — if equipped . . . . . . . 187 䡵 tilt/telescoping steering column . . . . . . . . . . 188 䡵 ...

  • Page 103

    ▫ adaptive cruise control (acc) menu . . . . . 207 ▫ display warnings and maintenance . . . . . . . 208 ▫ precautions while driving with acc . . . . . . 212 ▫ general information . . . . . . . . . . . . . . . . . . 216 ▫ normal (fixed speed) cruise control mode . . . . . . . . . . . . . . . . . . . ...

  • Page 104

    ▫ programming a rolling code . . . . . . . . . . . 238 ▫ programming a non-rolling code . . . . . . . . 240 ▫ canadian/gate operator programming . . . . 241 ▫ using homelink 威 . . . . . . . . . . . . . . . . . . . 242 ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 ▫ troubleshoo...

  • Page 105

    ▫ closing power shade — express . . . . . . . . . 250 ▫ closing power shade — manual mode . . . . . 250 ▫ pinch protect feature . . . . . . . . . . . . . . . . . 251 ▫ pinch protect override . . . . . . . . . . . . . . . . 251 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . 251 ▫ sunroo...

  • Page 106

    Mirrors automatic dimming mirror this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will illuminate to indicate when the dim- ming feature is activated. The mirror ...

  • Page 107

    Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they ...

  • Page 108

    Mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. Power mirror preselected positions can be controlled by the optional memory seat feature. Refer to “driv...

  • Page 109

    Lift the cover to reveal the mirror. The light will turn on automatically. Sun visor extension this feature has a pull out extension on the sun visor for increased coverage. Blind spot monitoring — if equipped the blind spot monitoring (bsm) system uses two radar- based sensors, located inside the r...

  • Page 110

    When the vehicle is started, the bsm warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational. The bsm system sensors operate when the vehicle is in any forward gear or reverse and enters stand by mode when the vehicle is in pa...

  • Page 111

    The bsm system notifies the driver of objects in the detection zones by illuminating the bsm warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “modes of operation” for further information. The bsm system monitors the...

  • Page 112

    Entering from the side vehicles that move into your adjacent lanes from either side of the vehicle. Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Side monitoring rear monitor...

  • Page 113

    Overtaking traffic if you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h)...

  • Page 114

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The bsm system will not alert you of objects t...

  • Page 115

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicles mirrors, glance over your shoulder...

  • Page 116

    Note: in a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When rcp is on and the vehicle is in reverse, the driver is alerted using both the visua...

  • Page 117

    Signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and detected object are present on the same side at the same time, both the visual and audio alerts will be issued. In addition to the audible a...

  • Page 118

    Phone using simple voice commands (e.G., “call” ѧ “mike” ѧ “work” or “dial” ѧ “248-555-1212”). Your mobile phone’s audio is transmitted through your vehi- cle’s audio system; the system will automatically mute your radio when using the uconnect™ phone. Note: the uconnect™ phone requires a mobile pho...

  • Page 119

    Warning! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in a collision causing serious injury or death. Uconnect™ phone button the radio or steering wheel con...

  • Page 120

    Operation voice commands can be used to operate the uconnect™ phone and to navigate through the uconnect™ phone menu structure. Voice commands are required after most uconnect™ phone prompts. You will be prompted for a specific command and then guided through the available options. • prior to giving...

  • Page 121

    Cancel command at any prompt, after the beep, you can say “cancel” and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (link) uconnect™ phone to a mobile phone to begin using your uconnect™ phone, you must pair your compatib...

  • Page 122

    Phone to use if multiple mobile phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the uconnect™ phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at an...

  • Page 123

    • the uconnect™ system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Add names to your uconnect™ phonebook note: adding names to the uconnect™ phonebook is recommended when the vehicle is not in motion. • press the button to be...

  • Page 124

    Phonebook download – automatic phonebook transfer from mobile phone if equipped and specifically supported by your phone, uconnect™ phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific bluetooth 威 phones with phone book access profile may s...

  • Page 125

    Edit uconnect™ phonebook entries note: • editing names in the phonebook is recommended when the vehicle is not in motion. • automatic downloaded phonebook entries cannot be deleted or edited. • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook edit entry”. ...

  • Page 126

    • after you enter the phonebook delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say “list names” to hear a list of the entries in the phonebook from which you choose. To select ...

  • Page 127

    • after the “ready” prompt and the following beep, say “phonebook list names”. • the uconnect™ phone will play the names of all the phonebook entries, including the downloaded phone- book entries, if available. • to call one of the names in the list, press the button during the playing of the desire...

  • Page 128

    Answer or reject an incoming call — call currently in progress if a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your mobile phone. Press the button to place the current call on hold and answ...

  • Page 129

    Conference call when two calls are in progress (one active and one on hold), press and hold the button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-way calling to initiate three-way calling, press the button while a call is in progress, ...

  • Page 130

    Call continuation call continuation is the progression of a phone call on the uconnect™ phone after the vehicle ignition key has been switched to off. Call continuation functionality avail- able on the vehicle can be any one of three types: • after the ignition key is switched to off, a call can con...

  • Page 131

    Emergency assistance if you are in an emergency and the mobile phone is reachable: • pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the uconnect™ phone is operational, you may reach the emergency number as follows: • press the button to begi...

  • Page 132

    Towing assistance if you need towing assistance: • press the button to begin. • after the “ready” prompt and the following beep, say “towing assistance”. Note: • the towing assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the u.S., 1-877-213-4525 f...

  • Page 133

    When calling a number with your uconnect™ phone that normally requires you to enter in a touch-tone sequence on your mobile phone keypad, you can press the button and say the sequence you wish to enter, followed by the word “send”. For example, if required to enter your pin followed with a pound, (3...

  • Page 134

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G., the uconnect™ phone will not repeat a phone number before you dial it). • press the button to begin. • after the “ready” prompt and the following beep, say one of the followi...

  • Page 135

    Mute/un-mute (mute off) when you mute the uconnect™ phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect™ phone: • press the button. • following the beep, say “mute”. In order to un-mute th...

  • Page 136

    • when prompted, say “list phones”. • the uconnect™ phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the button and say “select” or “delete”. Also, see the next two sec- tions f...

  • Page 137

    Things you should know about your uconnect™ phone uconnect™ phone tutorial to hear a brief tutorial of the system features, press the button and say “uconnect™ tutorial.” voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect™ pho...

  • Page 138

    Voice command • for best performance, adjust the rearview mirror to provide at least 1 ⁄ 2 in (1 cm) gap between the overhead console (if equipped) and the mirror. • always wait for the beep before speaking. • speak normally, without pausing, just as you would speak to a person sitting a few feet/me...

  • Page 139

    • numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • you can say “o” (letter “o”) for “0” (zero). • even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • in a ...

  • Page 140

    Sms uconnect™ phone can read or send new messages on your phone. Read messages: if you receive a new text message while your phone is connected to uconnect™ phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • press the button. • ...

  • Page 141

    List of preset messages: 1. Yes 2. No 3. Where are you? 4. I need more direction. 5. L o l 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See you in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18....

  • Page 142

    Turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and the following beep, say “setup, sms incoming message announcement,” you will then be given a choice to ...

  • Page 143

    3 understanding the features of your vehicle 141.

  • Page 144

    142 understanding the features of your vehicle.

  • Page 145

    3 understanding the features of your vehicle 143.

  • Page 146

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 144 unders...

  • Page 147

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

  • Page 148

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 149

    If you ever wish to interrupt the system while it lists options, press the voice command button, listen for the beep, and say your command. Pressing the voice command button while the system is speaking is known as “barging in.” the system will be interrupted, and after the beep, you can add or chan...

  • Page 150

    3. Use the on/off volume rotary knob to adjust the volume to a comfortable level while the voice command system is speaking. Please note the volume setting for voice command is different than the audio system. Main menu start a dialogue by pressing the voice command button. You may say “main menu” t...

  • Page 151

    • “menu radio” (to switch to the radio menu) • “main menu” (to switch to the main menu) satellite radio to switch to satellite radio mode, say “sat” or “satellite radio”. In this mode, you may say the following com- mands: • “channel number” (to change the channel by its spoken number) • “next chann...

  • Page 152

    − “continue” (to continue recording) − “delete” (to delete the recording) • “play memos” (to play previously recorded memos) — during the playback you may press the voice command button to stop playing memos. You proceed by saying one of the following commands: − “repeat” (to repeat a memo) − “next”...

  • Page 153

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect™ voice “voice training” feature may be used. 1. Press the voice command button, say “system setup” and once you are in that menu then say “voice training.” this will train your...

  • Page 154

    Are located on the outboard side of the seat. There are two switches that control the movement of the seat cushion and the seatback. Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the directio...

  • Page 155

    Reclining the seatback the angle of the seatback can be adjusted forward or backward. Push the seatback switch forward or rear- ward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Warning! • adjusting a seat while driving may be dan...

  • Page 156

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting the seat up or down the height of the seats...

  • Page 157

    Caution! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Power lumbar — if equipped vehicles equipped with power driver or passenger seat...

  • Page 158

    Manual front seats forward/rearward adjustment some models may be equipped with manual front driver or passenger seats. The seats can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor. While sitting in the seat, lift up on the bar located under t...

  • Page 159

    Manual front passenger seatback adjustment — recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired position and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the sea...

  • Page 160

    Front passenger seat fold-flat feature — if equipped to fold the seatback to the flat load-floor position, lift the recline lever and push the seatback forward. To return to the seating position, raise the seatback and lock it into place. Heated seats — if equipped on some models, the front and rear...

  • Page 161

    Vehicles equipped with remote start on models that are equipped with remote start, the driver’s heated seat and heated steering wheel can be programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to know before starting your vehicle” for further infor...

  • Page 162

    Rear heated seats on some models, the two outboard seats are equipped with heated seats. There are two heated seat switches that allow the rear passengers to operate the seats indepen- dently. The heated seat switches for each heater are located on the rear of the center console. You can choose from...

  • Page 163

    To one, indicating the change. The low-level setting will turn off automatically after a maximum of 45 minutes. Ventilated seats — if equipped on some models, both the driver and passenger seats are ventilated. Located in the seat cushion and seatback are small fans that draw the air from the passen...

  • Page 164

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear- impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be...

  • Page 165

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. For comfort the active head restraints can be tilted forward and rearward. To tilt the head restrain...

  • Page 166

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 167

    Warning! (continued) • active head restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the ac- tive head restraint ensure that all cargo is se- cured, as loose cargo could contact the active head restraint during sudden st...

  • Page 168

    Warning! Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure the outboard head re- straints are in their upright positions when the seat is to be occupied. Note: for proper routing of a child seat tether refer to ...

  • Page 169

    2. Fold the rear seat completely forward. To raise rear seat raise the rear seatback and lock it into place. If interfer- ence from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Warning! • be certain that the seatback is ...

  • Page 170

    Reclining rear seat to recline the seatback, lift the lever located on the outboard side of the seat, lean back and release the lever at the desired position. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the seatback reclined so that the shoul...

  • Page 171

    Your vehicle is equipped with two rke transmitters. One or both rke transmitters can be linked to either memory position. The memory system can accommodate up to four rke transmitters, each one linked to either of the two memory positions. Setting memory positions and linking remote keyless entry tr...

  • Page 172

    5. Turn on the radio and set the radio station presets (up to 12 am and 12 fm stations can be set). 6. Turn the ignition switch to the lock/off position and remove the key. 7. Press and release the s (set) button located on the driver’s door. 8. Within five seconds, press and release memory button 1...

  • Page 173

    To recall the memory setting for driver two, press memory button number 2 on the driver’s door, or the unlock button on the rke transmitter linked to memory position 2. A recall can be cancelled by pressing any of the memory buttons on the drivers door during a recall (s, 1, or 2). When a recall is ...

  • Page 174

    Easy entry/exit seat this feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. There are two possible easy entry/exit adjustments available: • the seat cushion will move rearward approximately 2.5 in (60 mm), if the starting position of...

  • Page 175

    To open and close the hood to open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door. 2. Reach under the hood, move safety latch to the left and lift the hood. Caution! To prevent possible damage, do not slam the ho...

  • Page 176

    Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. Lights headlight switch the headlight switch is located...

  • Page 177

    Note: • your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less susceptible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore differ- ent lens cleaning procedures must be followed. • to minimize the po...

  • Page 178

    Information center (evic)/customer-programmable features” in “understanding your instrument panel” for further information. If your vehicle is equipped with a “rain sensitive wiper system” and it is activated, the headlights will automati- cally turn on after the wipers complete five wipe cycles wit...

  • Page 179

    Note: this system will not activate until the vehicle is at or above 20 mph (32 km/h). To deactivate 1. Pull the multifunction lever toward you (or rearward in car) to manually deactivate the system (normal opera- tion of low beams). 2. Push back on the multifunction lever once again to reactivate t...

  • Page 180

    On, and then the headlight switch is cycled off. Headlight delay can be cancelled by either turning the headlight switch on then off, or by turning the ignition on. The headlight delay time is programmable on vehicles equipped with an electronic vehicle information center (evic). Refer to “electroni...

  • Page 181

    Interior lights courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the headlight switch) is rotated to the its farthest upward position, or if equipped, when the unlock button is pressed on the remote keyless entry (rk...

  • Page 182

    Lights-on reminder if the headlights, parking lights, or cargo lights are left on after the ignition is turned off, a chime will sound when the driver’s door is opened. Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. I...

  • Page 183

    Each light can be turned on by pressing a switch on either side of the console. These buttons are backlit for night time visibility. To turn the lights off, press the switch a second time. The lights will also turn on when the unlock button on the remote keyless entry (rke) is pressed. Ambient light...

  • Page 184

    Multifunction lever the multifunction lever is located on the left side of the steering column. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light re...

  • Page 185

    High/low beam switch push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off. Windshield wipers and washers the windshield wiper/washer control...

  • Page 186

    Windshield wiper operation rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation. Caution! Always remove any buildup of snow that prevents the windshield wiper blades fro...

  • Page 187

    Note: if the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield washer operation to use the washer, push on the end of the lever (toward the steering wheel) and hold while spray is desired. If the lever is pushed while in the intermittent setting, the wipers will t...

  • Page 188

    Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist use the mist...

  • Page 189

    Rain sensing wipers — if equipped this feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of ...

  • Page 190

    Operate until the wiper switch is moved, vehicle speed is greater than 0 mph (0 km/h), or the outside tem- perature is greater than 32°f (0°c). • transmission in neutral position — when the ignition is on, and the transmission is in the neu- tral position, the rain sensing system will not operate un...

  • Page 191

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this war...

  • Page 192

    Note: for vehicles equipped with driver memory seat, you can use your remote keyless entry (rke) transmitter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to pre-programmed positions. Refer to “driver memory seat” in this section for further infor...

  • Page 193

    Note: the engine must be running for the heated steering wheel to operate. Vehicles equipped with remote start on models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to kn...

  • Page 194

    The electronic speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic ...

  • Page 195

    To set a desired speed turn the electronic speed control on. When the vehicle has reached the desired speed, press the set (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. Note: the vehicle should be traveling at a steady speed and on level ground b...

  • Page 196

    To decrease speed while the electronic speed control is set, push the set (-) button. If the button is continually held in the set (-) position, the set speed will continue to decrease until the button is released. Release the button when the desired speed is reached, and the new set speed will be e...

  • Page 197

    Adaptive cruise control (acc) — if equipped adaptive cruise control (acc) increases the driving convenience provided by cruise control while traveling on highways and major roadways. However, it is not a safety system and not designed to prevent collisions. Acc will allow you to keep cruise control ...

  • Page 198

    Warning! (continued) • the acc system: − does not react to pedestrians, oncoming ve- hicles, and stationary objects (e.G., a stopped ve- hicle in a traffic jam or a disabled vehicle). − cannot take street, traffic, and weather condi- tions into account, and may be limited upon ad- verse sight distan...

  • Page 199

    The cruise control system has two control modes: • adaptive cruise control mode for maintaining an appropriate distance between vehicles. • normal (fixed speed) cruise control mode for cruising at a constant preset speed. For additional information, refer to “normal (fixed speed) cruise control mode...

  • Page 200

    Note: any chassis/suspension modifications to the vehicle will effect the performance of the adaptive cruise control. Activating adaptive cruise control (acc) you can only activate acc if the vehicle speed is above 20 mph (32 km/h). When the system is turned on and in the ready state, the electronic...

  • Page 201

    To activate push and release the on/off button. The acc menu in the evic displays “adaptive cruise ready.” to turn the system off, push and release the on/off button again. At this time, the system will turn off and the evic will display “adaptive cruise control off.” warning! Leaving the adaptive c...

  • Page 202

    To set a desired acc speed when the vehicle reaches the speed desired, push the set - button and release. The evic will display the set speed. Remove your foot from the accelerator pedal. If you do not, the vehicle may continue to accelerate beyond the set speed. If this occurs: • the message “drive...

  • Page 203

    To cancel the system will disable acc without erasing the memory if: • you softly tap the brake pedal. • you depress the brake pedal. • you press the cancel switch. • an anti-lock brake system (abs) event occurs. • a trailer sway control (tsc) event occurs. • if the transmission is shifted into neut...

  • Page 204

    Note: if acc is resumed or set with the esc/tcs off, esc will automatically be re-engaged. To turn off the system will turn off and erase the set speed in memory if: • you push the on/off button. • you turn off the ignition. • you switch to four-wheel drive low. To resume speed press the res + butto...

  • Page 205

    To vary the speed setting while acc is set, you can increase the set speed by pressing and holding the res + button. If the button is continually pressed, the set speed will continue to in- crease in 5 mph (8 km/h) increments until the button is released. The increase in set speed is reflected in th...

  • Page 206

    Setting the following distance in acc the specified following distance for acc can be set by varying the distance setting between 3 (long), 2 (me- dium), and 1 (short). Using this distance setting and the vehicle speed, acc calculates and sets the distance to the vehicle ahead. This distance setting...

  • Page 207

    To change the distance setting, press the distance button and release. Each time the button is pressed, the distance setting adjusts between long, medium, and short. If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle is detected in the same lane, the ev...

  • Page 208

    • the system disengages. (refer to the information on acc activation). The maximum braking applied by acc is limited; how- ever, the driver can always apply the brakes manually, if necessary. Note: the brake lights will illuminate whenever the acc system applies the brakes. A proximity warning will ...

  • Page 209

    Adaptive cruise control (acc) menu the evic displays the current acc system settings. The evic is located in the upper part of the instrument cluster between the speedometer and the tachometer. The information it displays depends on acc system status. Press the menu button (located on the steer- ing...

  • Page 210

    The acc screen will display once again if any acc activity occurs, which may include any of the following: • set speed change • distance setting change • system cancel • driver override • system off • acc proximity warning • acc unavailable warning the evic will return to the last display selected a...

  • Page 211

    Note: if the acc “clean radar sensor in front of vehicle” warning is active normal (fixed speed) cruise control is still available. For additional information refer to “normal (fixed speed) cruise control mode” in this section. If weather conditions are not a factor, the driver should examine the se...

  • Page 212

    • do not attach or install any accessories near the sensor, including transparent material or aftermarket grilles. Doing so could cause an acc system failure or malfunction. When the condition that deactivated the system is no longer present, the system will return to the “adaptive cruise control of...

  • Page 213

    Note: do not change the adjustment fasteners or pull the sensor off of the bracket. Doing so may misalign the sensor. Store the sensor and bracket assembly in a safe location. The wiring and connector must be stowed properly after the sensor and bracket assembly is removed. A connector plug is stowe...

  • Page 214

    Service acc warning if the system turns off, and the evic displays “acc/ fcw unavailable service radar sensor”, it indicates there is an internal system fault. Although the vehicle is still drivable under normal conditions, have the system checked by an authorized dealer. Precautions while driving w...

  • Page 215

    Offset driving acc may not detect a vehicle in the same lane that is offset from your direct line of travel. There will not be sufficient distance to the vehicle ahead. The offset vehicle may move in and out of the line of travel, which can cause your vehicle to brake or accelerate unexpectedly. Tur...

  • Page 216

    Using acc on hills when driving on hills, acc may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, acc perfor- mance may be limited. Lane changing acc will not detect a vehicle until it is completely in the lane in which you...

  • Page 217

    Narrow vehicles some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There will not be suffi- cient distance to the vehicle ahead. 3 understanding the features of your vehicle 215.

  • Page 218

    Stationary objects and vehicles acc does not react to stationary objects and stationary vehicles. For example, acc will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if nece...

  • Page 219

    Warning! In the normal cruise control mode, the system will not react to vehicles ahead. In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is ...

  • Page 220

    To resume press the res + button and then remove your foot from the accelerator pedal. The evic will display the last set speed. To turn off the system will turn off and erase the set speed in memory if: • you push the on/off button. • you turn off the ignition. • you engage four-wheel drive low. If...

  • Page 221

    Note: • the minimum speed for fcw activation is 10 mph (16 km/h). • when entering or driving in a curve, the fcw alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course predic- tion. This is expected and is a part of normal fcw activation and func...

  • Page 222

    Fcw settings can only be changed when the vehicle is in park. The default status of fcw is the “far” setting, this allows the system to warn you of a possible collision with the vehicle in front of you when you are farther away. This gives you the most reaction time. Changing the fcw status to the “...

  • Page 223

    Changing the fcw status to “off” prevents the system from warning you of a possible collision with the vehicle in front of you. Note: in the “off” setting fcw off will be displayed in the evic. Note: • the system will retain the last setting selected by the driver after ignition shut down. Example o...

  • Page 224

    • fcw will not react to irrelevant objects such as over- head objects, ground reflections, objects not in the path of the car, stationary objects that are far away, oncom- ing traffic, or leading vehicles with the same or higher rate of speed. • fcw will be disabled like acc below with the un- avail...

  • Page 225

    Parksense 姞 rear park assist — if equipped the parksense 威 rear park assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to parksense 威 system usage precautions for limitations of...

  • Page 226

    The parksense 威 warning display is located in the instru- ment cluster’s evic display. It provides both visual and audible warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. Parksense 姞 display when the vehicle is in reverse, the warning display will turn on ...

  • Page 227

    The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the evic display will show fewer arcs and the sound tone will change from slow, to fast, to continuous. Park assist system off slow tone 3 under...

  • Page 228

    The vehicle is close to the obstacle when the evic display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: fast tone continuous tone 226 understanding the features of your vehicle.

  • Page 229

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-39 in (200-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible alert chime none single 1/2 second tone slow fast continuous display message park assist system on warning object detected warning object de...

  • Page 230

    “electronic vehicle information center (evic)” in “un- derstanding your instrument panel” for further informa- tion. When the shift lever is moved to reverse and the system is disabled, the evic will display the “park assist system off” message for as long as the vehicle is in reverse. The parksense...

  • Page 231

    Parksense 姞 system usage precautions note: • ensure that the rear bumper is free of snow, ice, mud, dirt and debris to keep the parksense 威 system operat- ing properly. • jackhammers, large trucks, and other vibrations could affect the performance of parksense 威 . • when you turn parksense 威 off, th...

  • Page 232

    • on vehicles equipped with a tailgate, parksense 威 should be disabled when the tailgate is in the lowered or open position and the vehicle is in reverse. A lowered tailgate could provide a false indication that an obstacle is behind the vehicle. Caution! • parksense 威 is only a parking aid and it i...

  • Page 233

    Warning! (continued) • before using the parksense 威 rear park assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles becau...

  • Page 234

    When displayed, static grid lines will illustrate the width of the vehicle while a dashed center-line will indicate the center of the vehicle to assist with aligning to a hitch/ receiver. The static grid lines will show separate zones that will help indicate the distance to the rear of the vehicle. ...

  • Page 235

    Warning! Drivers must be careful when backing up even when using the parkview 威 rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your...

  • Page 236

    4. Enable or disable the rear camera feature by selecting the “enable rear camera in reverse” soft-key. 5. Press the “save” soft-key. Turning parkview 姞 on or off — without navigation/multimedia radio 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 3. Enable or disable the rear came...

  • Page 237

    To turn the lights off, press the switch a second time. The lights also turn on when a door is opened. The lights will also turn on when the unlock button on the rke is pressed. Sunglass bin door at the front of the console a compartment is provided for the storage of a pair of sunglasses. The stora...

  • Page 238

    Garage door opener — if equipped homelink 威 replaces up to three hand-held transmitters that operate devices such as garage door openers, motor- ized gates, lighting or home security systems. The homelink 威 unit is powered by your vehicles 12 volt battery. The homelink 威 buttons, located on either t...

  • Page 239

    Note: homelink 威 is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink 姞 be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is rec...

  • Page 240

    Programming a rolling code for programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “learn” or “train” button located where the hanging antenna is attached to the garage door opener. It is not the button that is normally used to open...

  • Page 241

    3. Simultaneously press and hold both the homelink 威 button you want to program and the hand-held transmit- ter button. 4. Continue to hold both buttons and observe the indi- cator light. The homelink 威 indicator will flash slowly and then rapidly after homelink 威 has received the fre- quency signal...

  • Page 242

    2. Press and hold the desired homelink 威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “program- ming a rolling code” step 2 and follow all remaining steps. Programming a non-rolling code for programming gar...

  • Page 243

    Reprogramming a single homelink 威 button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink 威 button until the indicator light begins to flash after 20 seconds. Do not release the but...

  • Page 244

    4. Watch for the homelink 威 indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you are programming. 5. Press and hold the programmed homelink 威 button and observe the indicator light. • if...

  • Page 245

    Security it is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The homelink 威 universal transceiver i...

  • Page 246

    Warning! • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” fea...

  • Page 247

    Power sunroof — if equipped the power sunroof switch is located between the sun visors on the overhead console. Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating t...

  • Page 248

    Opening sunroof — express press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automati- cally. This is called “express open”. During express open operation, any movement of the sunroof switch ...

  • Page 249

    Note: if three consecutive sunroof close attempts re- sult in pinch protect reversals, the fourth close attempt will be a manual close movement with pinch protect disabled. Venting sunroof — express press and release the vent button within one half second and the sunroof will open to the vent positi...

  • Page 250

    Ignition off operation the power sunroof switches remain active for up to approximately ten minutes after the ignition switch has been turned off. Opening either front door will cancel this feature. The time is programmable. Refer to “elec- tronic vehicle information center (evic)/personal set- ting...

  • Page 251

    Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • in a collision, there is a gre...

  • Page 252

    Position. The sunroof will close fully and stop automati- cally. This is called “express close”. During express close operation, any movement of the switch will stop the sunroof. Closing sunroof — manual mode to close the sunroof, press and hold the switch in the forward position. Any release of the...

  • Page 253

    Pinch protect feature this feature will detect an obstruction in the opening of the sunroof during express close operation. If an ob- struction is detected, the sunroof will automatically re- tract. Remove the obstruction if this occurs. Next, press the switch forward and release to express close. N...

  • Page 254

    The ignition switch has been turned off. Refer to “elec- tronic vehicle information center (evic)/customer- programmable features (system setup)” in “under- standing your instrument panel” for further information. Note: opening either front door will cancel this feature. Sunroof fully closed press t...

  • Page 255

    The front power outlet is located inside the storage area on the center stack of the instrument panel. Push inward on the storage lid to open the compartment and gain access to this power outlet. In addition to the front power outlet, there is also a power outlet located in the storage area of the c...

  • Page 256

    The rear power outlet is located in the right rear cargo area. Note: the rear power outlet can be switched to “battery” powered all the time by switching the power outlet right rear quarter panel fuse in the fuse panel. Rear power outlet power outlet right rear quarter panel fuse 254 understanding t...

  • Page 257

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 258

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 259

    The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximat...

  • Page 260

    Warning! To avoid serious injury or death: • do not use a three-prong adaptor. • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled it may cause an electric shock and failure. Cupholders there are two cuphold...

  • Page 261

    There are two cupholders for the rear seat passengers located in the fold-down center armrest. Storage glove compartment the glove compartment is located on the right side of the instrument panel. Rear cupholders glove compartment 3 understanding the features of your vehicle 259.

  • Page 262

    To open the glove compartment, pull outward on the latch and lower the glove box door. Door storage large storage areas are built into the door panels for easy access. Opened glove compartment door panel storage 260 understanding the features of your vehicle.

  • Page 263

    Center console the center console contains both an upper and a lower storage area. To open the upper storage compartment, pull upward on the small latch located on the lid. Storage compartment storage compartment latches 3 understanding the features of your vehicle 261.

  • Page 264

    Lift upward on the larger of the latches to access the lower storage compartment. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices whi...

  • Page 265

    To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Press and release three-press switch 3 understanding the features of your vehicle 263.

  • Page 266

    Cargo storage bins there are four removable storage bins located in the rear cargo area. There are two storage bins located on either side of the cargo area. Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether hoo...

  • Page 267

    Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the...

  • Page 268

    3. The liftgate may be opened with the cargo cover in place. Warning! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remo...

  • Page 269

    Cargo tie-down hooks the cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying ...

  • Page 270

    Warning! (continued) • do not carry loads which exceed the load limits described on the label attached to the left door or left door center pillar. • always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • place as much cargo as possible in front of...

  • Page 271

    Rotate the center portion of the lever upward to the first detent for intermittent operation and to the second detent for continuous rear wiper operation. Rotating the center portion upward once more will activate the washer pump which will continue to operate as long as the switch is held. Upon rel...

  • Page 272

    Note: to prevent excessive battery drain, use the rear window defroster only when the engine is operating. Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior su...

  • Page 273

    Rack frame. Once the crossbar is in the desired position, retighten the with the wrench to lock the crossbar into position. Note: • to help control wind noise when the crossbars are not in use, place the front and rear crossbars approxi- mately 24 in (61 cm) apart. Optimal noise reduction can then b...

  • Page 274

    Caution! (continued) • long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • travel at reduced speeds and turn corners care- fully when carrying large or heavy loads on the roof ...

  • Page 275: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 277 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 278 䡵 instrument cluster descriptions . . . . . . . . . . . 279 䡵 electronic vehicle information center (evic) . . 289 ▫ electronic ...

  • Page 276

    ▫ turn menu off . . . . . . . . . . . . . . . . . . . . . . 312 ▫ tire psi . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ keyless enter-n-go display — if equipped . . . . . . . . . . . . . . . . . . . . . . . . 314 ▫ compass / temperature display . . . . . . . . . 314 ▫ customer-program...

  • Page 277

    ▫ uconnect™ multimedia (satellite radio) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 346 ▫ operating instructions (uconnect™ phone) — if equipped . . . . . . . 350 䡵 ipod 威 /usb/mp3 control — if equipped . . . . . 350 ▫ connecting the ipod 威 or external usb device . . . . . . ....

  • Page 278

    ▫ replacing the batteries . . . . . . . . . . . . . . . . 371 ▫ headphones operation . . . . . . . . . . . . . . . . 372 ▫ controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 ▫ replacing the batteries . . . . . . . . . . . . . . . . 374 ▫ unwired 威 stereo headphone lifetime limited wa...

  • Page 279

    Instrument panel features 1 — air outlet 6 — lower switch bank 11 — hood release 2 — instrument cluster 7 — hazard switch 12 — fuel door release 3 — radio 8 — storage bin 13 — headlight switch 4 — glove compartment 9 — esc button 14 — dimmer control 5 — climate controls 10 — ignition switch 4 unders...

  • Page 280

    Instrument cluster 278 understanding your instrument panel.

  • Page 281

    Instrument cluster descriptions 1. Tachometer indicates the engine speed in revolutions per minute (rpm x 1000). 2. Air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to the on/run position. If the light is either not on d...

  • Page 282

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to...

  • Page 283

    5. Tow/haul indicator light — if equipped this light will illuminate when the tow/ haul button has been selected. The tow/ haul button is located in the center of the instrument panel (below the climate controls). 6. Turn signal indicator the arrows will flash with the exterior turn signals when the...

  • Page 284

    As it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ service,...

  • Page 285

    Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped wi...

  • Page 286

    12. Park/headlight on indicator — if equipped this indicator will illuminate when the park lights or headlights are turned on. 13. Seat belt reminder light when the ignition switch is first turned to the on/run position, this light will turn on for four to eight seconds as a bulb check. During the b...

  • Page 287

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 288

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Anti-lock brake (abs) light this light monitors the anti-lock brake sy...

  • Page 289

    19. Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position. 20. Electronic vehicle information center (evic) white telltale area this area will display the evic reconfigurable white telltales. For further information, refer to “electronic v...

  • Page 290

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If ...

  • Page 291

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • vehicle information warning message displays • personal settings (cus...

  • Page 292

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: up button press and release the up button to scroll up- ward through the main menus (fuel economy, vehicle info, tire psi, cruise, messages, units, system setup, vehicle speed, trip in...

  • Page 293

    Back button press the back button to scroll back to a previous menu or sub-menu. Electronic vehicle information center (evic) displays the evic display consists of three sections: 1. The top line where compass direction, odometer line and outside temperature are displayed. 2. The main display area w...

  • Page 294

    Of this message type are ⬙ turn signal on ⬙ (if a turn signal is left on) and ⬙ lights on ⬙ (if driver leaves the vehicle). • unstored messages until run these messages deal primarily with the remote start feature. This message type is displayed until the ignition is in the run state. Examples of th...

  • Page 295

    • keyfob battery low • liftglass open • left front turn signal lamp out • right front turn signal lamp out • left rear turn signal lamp out • right rear turn signal lamp out • low tire pressure • esc system off • service blind spot system • blind spot detection unavailable • blind spot system off • ...

  • Page 296

    • acc cancelled — to disable the acc system. Refer to “adaptive cruise control (acc)” in “understanding the features of your vehicle” (if equipped). • sensed vehicle indicator — the system detects a slower moving vehicle in the same lane. Refer to “adaptive cruise control (acc)” in “understanding th...

  • Page 297

    • acc/fcw unavailable service radar sensor — if the acc system turns off due to an internal system fault that requires service from an authorized dealer. Refer to “adaptive cruise control (acc)” in “understand- ing the features of your vehicle” (if equipped). • cruise off when park brake is on • acc...

  • Page 298

    • memory system unavailable — not in park • memory system unavailable — seatbelt buckled • memory 1 profile recall • memory 2 profile recall • press brake pedal and push button to start • wrong key • damaged key • key not programmed • function currently unavailable — power liftgate • unlock to opera...

  • Page 299

    • terrain system settings not available • raising vehicle ride height (with icon) • lowering vehicle ride height (with icon) • normal vehicle ride height — this message is dis- played (for 5 seconds) when the vehicle has achieved the normal vehicle ride height. • off road ride height level 1 — this ...

  • Page 300

    • selected ride height not permitted — the vehicle speed is too high to enter one of the preset levels (entry/exit level/off road ride height level 1/off road ride height level 2). • air suspension system cooling down – please wait — this message is displayed if the compressor tempera- ture level is...

  • Page 301

    • electronic speed control set this light will turn on when the electronic speed control is set. For further information, refer to “electronic speed control” in “under- standing the features of your vehicle.” • adaptive cruise control (acc) on this light will turn on when the acc is on. For further ...

  • Page 302

    • if the condition persists, see your authorized dealer for service. Evic amber telltale lights this area will show reconfigurable amber caution tell- tales. These telltales include: • forward collision warning (fcw) off this light warns the driver of a potential colli- sion with the vehicle in fron...

  • Page 303

    A loose, improperly installed, or damaged fuel filler cap may also turn on the malfunction indicator light (mil). • windshield washer fluid low indicator this light will turn on to indicate the wind- shield washer fluid is low. • serv 4wd the serv 4wd light monitors the electric shift 4wd system. If...

  • Page 304

    • oil pressure warning light this telltale indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This...

  • Page 305

    Required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • engine temperature warning light this light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches h, this indicator will illuminate and...

  • Page 306

    Warning! If the transmission temperature warning light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. Engine oil change indicator system oil change due your v...

  • Page 307

    Vehicles not equipped with keyless enter-n-go 1. Turn the ignition switch to the on/run position (do not start the engine.) 2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 3. Turn the ignition switch to the off/lock position. Note: if the indicator message illuminates ...

  • Page 308

    (mds) (if equipped) allows the engine to operate on four cylinders, or if you are driving in a fuel efficient manner. This feature allows you to monitor when you are driving in a fuel efficient manner, and it can be used to modify driving habits in order to increase fuel economy. Distance to empty (...

  • Page 309

    Vehicle speed press and release the up or down button until “vehicle speed” displays highlighted in the evic and press the select button. Press the select button to display the current speed in mph or km/h. Pressing the select button a second time will toggle the unit of measure between mph or km/h....

  • Page 310

    Elapsed time shows the total elapsed time of travel since the last reset when the ignition switch is in the acc position. Elapsed time will increment when the ignition switch is in the on or start position. To reset the display reset will only occur while a resettable function is being displayed. Pr...

  • Page 311

    This light will illuminate when the sport mode is selected. This mode provides performance based tuning with improved handling through an electronic controlled damping system. This system reduces body roll and pitch in many driving situations including cornering, acceleration and braking. For furthe...

  • Page 312

    • the time will continue to display until the select button is pressed. • pressing the select button will clear the current run time and display the vehicle’s best 0-60 mph (0-100 km/h) time. • to clear the vehicle’s best 0-60 mph (0-100 km/h) time, press and hold the select button for five seconds....

  • Page 313

    • dashes will display if the vehicle fails to reach 1/8 mile (1/4 mile) in less then 30 seconds. • the time and speed will continue to display until the select button is pressed. • pressing the select button will clear the current run and display the vehicle’s best 1/8 mile (1/4 mile) run. • to clea...

  • Page 314

    Vehicle info (customer information features) press and release the up or down button until “vehicle info” displays in the evic and press the select button. Press the up and down button to scroll through the available information displays, then press select to display any one of the following choices...

  • Page 315

    Tire psi press and release the up or down button until “tire psi” displays highlighted in the evic and press the select button. Press and release the up/down but- tons until one of the following system status messages displays in the evic: • system ok • system warnings displayed (will display all cu...

  • Page 316

    • your system can be set to display pressure units in psi, kpa, or bar. Keyless enter-n-go display — if equipped when the engine start/stop button is pressed to change ignition switch positions, the keyless enter-n-go icon momentarily appears in the lower right corner of the evic display showing the...

  • Page 317

    Note: a good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. Compass variance compass variance is the difference between magnetic north and geographic north. To compensate for the differenc...

  • Page 318

    3. Press the down button until the “compass variance” message is displayed in the evic, then press the select button. The last variance zone number displays in the evic. 4. Press and release the select button until the proper variance zone is selected, according to the map. 5. Press and release the ...

  • Page 319

    Customer-programmable features (system setup) personal settings allows you to set and recall features when the transmission is in park. If the transmission is out of park or the vehicle begins moving, a warning message setup not available, is followed in three seconds by, vehicle not in park. Press ...

  • Page 320

    Feature showing the system has been activated, or the check-mark is removed showing the system has been deactivated. Remote unlock sequence when unlock driver door only on 1st press is selected, only the driver’s door will unlock on the first press of the rke transmitter unlock button. When driver d...

  • Page 321

    Make your selection, press and release the select button a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Refer to “driver memory seat” in “understanding the fea- tures of your vehicle.” remote start ...

  • Page 322

    Flash lamps with lock when this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the rke transmitter. This feature may be selected with or without the sound horn on lock feature selected. To make your selection, press and release the select b...

  • Page 323

    Easy entry/exit seat (available with memory seat only) this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection, press and release the select button until a check-mark appears next to the feature showing the syst...

  • Page 324

    Illuminated approach when this feature is selected, the headlights will activate and remain on for 0, 30, 60, or 90 seconds when the doors are unlocked with the rke transmitter. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the select bu...

  • Page 325

    Wiper mode — if equipped when this feature is selected, the system will automati- cally activate the windshield wipers if it senses moisture on the windshield. To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activ...

  • Page 326

    Forward collision warning the forward collision warning (fcw) feature can be can be set to far, set to near or turned off. The default status of fcw is the far setting. This means the system will warn you of a possible collision with the vehicle in front of you when you are farther away. This gives ...

  • Page 327

    Calibrate compass refer to “compass display” for more information. Compass variance refer to “compass display” for more information. Media center 730n/430/430n (rhr/rer/rbz/ rhb) cd/dvd/hdd/nav — if equipped note: the sales code is located on the lower right side of the unit’s faceplate. Refer to yo...

  • Page 328

    Media center 130 (sales code res) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume contro...

  • Page 329

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. Time button press the time button to alternate display of the time and radio frequency. Clo...

  • Page 330

    Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary tune/scroll control knob a fourth time and balance will display. Turn the tune/ scroll control knob to the r...

  • Page 331

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory (12 am and 12 fm stations). Disc button pressing the disc button will allow you to switch from am/fm modes to disc modes. Op...

  • Page 332

    Caution! • this cd player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • the res media center is a single cd player. Do not attempt to insert a second c...

  • Page 333

    Am/fm button press the button to select either am or fm mode. Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek bu...

  • Page 334

    A number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙ . ⬙ and a three- character extension) • l...

  • Page 335

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and a...

  • Page 336

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the dis...

  • Page 337

    Operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume ...

  • Page 338

    Phone button uconnect™ phone — if equipped press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” in the uconnect™ user manual located on the dvd for further details. If your vehicle is not equipped with or this feature is not available on your vehicle, a ...

  • Page 339

    Info button press the info button for an rds station (one with call letters displayed). The radio will return a radio text message broadcast from an fm station (fm mode only). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the directi...

  • Page 340

    Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast music type inf...

  • Page 341

    Program type 16-digit character display top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a prese...

  • Page 342

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored i...

  • Page 343

    If you insert a disc with the ignition on/run and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player wil...

  • Page 344

    Rw/ff press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or another cd button is pressed. The rw (reverse) button works in a similar manner. Am/fm button press the button to select either am or fm mode. Set/rnd button (random play button) press t...

  • Page 345

    • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. With a maximum number of files, exce...

  • Page 346

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and a...

  • Page 347

    List button (cd mode for mp3 play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that folde...

  • Page 348

    Time button (auxiliary mode) press this button to change the display to time of day. The time of day will display for five seconds (when the ignition is off). Uconnect™ multimedia (satellite radio) — if equipped satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide c...

  • Page 349

    Using the tune/scroll control knob until sirius id is selected. Press the tune/scroll control knob and the sirius id number will display. The sirius id number display will time out in two minutes. Press any button on the radio to exit this screen. Selecting uconnect™ multimedia (satellite) mode pres...

  • Page 350

    Seek buttons press and release the seek buttons to search for the next channel in satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without st...

  • Page 351

    By pressing the seek button when the music type function is active, the radio will be tuned to the next channel with the same selected music type name. If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the prese...

  • Page 352

    Operating instructions (uconnect™ phone) — if equipped refer to “uconnect™ phone” in the uconnect™ user manual located on the dvd for further details. Ipod 姞 /usb/mp3 control — if equipped note: this section is for sales code res and req/ rel/ret radios only with uconnect™. For sales code rbz/rhb, r...

  • Page 353

    Note: the center console will have a position where the ipod 威 or consumer electronic audio device cable can be routed through without damaging the cable when closing the lid. A factory cut out space for the cable to be routed may be located in the base of the center console on either the front or s...

  • Page 354

    Using this feature by using ipod cable or external usb device to connect to usb port: • the audio device can be played on the vehicle’s sound system, providing metadata (artist, track title, album, etc.) information on the radio display. • the audio device can be controlled using the radio buttons t...

  • Page 355

    • jump backward in the current track by pressing and holding the rw button. Holding the rw button long enough will jump to the beginning of the current track. • jump forward in the current track by pressing and holding the ff >> button. • a single press backward rw or forward ff >> will jump backwar...

  • Page 356

    Device, or press the vr button and say ⬙ shuffle on ⬙ or ⬙ shuffle off ⬙ . If the rnd icon is showing on the radio display, then the shuffle mode is on. List or browse mode during play mode, pressing any of the buttons described below, will bring up list mode. List mode enables scrolling through the...

  • Page 357

    • preset 6 – podcasts • pressing a preset button will display the current list on the top line and the first item in that list on the second line. • to exit list mode without selecting a track, press the same preset button again to go back to play mode . • list button: the list button will display t...

  • Page 358

    Bluetooth streaming audio (btsa) music can be streamed from your cellular phone to the uconnect™ phone system. Controlling btsa using radio buttons to get into the btsa mode, press either “aux” button on the radio or press the vr button and say “bluetooth streaming audio”. Play mode when switched to...

  • Page 359

    Uconnect™ multimedia video entertainment system (ves)™ — if equipped getting started • screen located in the overhead console : unfold the overhead lcd screen by pushing the button on the overhead console behind the screen. • with the ignition switch in the on or acc position, turn the radio on by p...

  • Page 360

    Or press the load button then corresponding number (1–6) where the dvd is to be loaded (non-touch-screen). 2. Insert the dvd with the label facing up. The radio automatically selects the appropriate mode after the disc is recognized and displays the menu screen or starts playing the first track. 3. ...

  • Page 361

    2. Touch the rear ves soft-key to display the rear ves controls. If a channel list appears on the right side of the screen, touch the hide list soft-key to display the rear ves controls screen. 3. Touch the 1 soft-key and then the disc soft-key in the media column. To exit touch the back arrow soft-...

  • Page 362

    Note: • to view a dvd on the radio press the radio/media hard-key, on the radio faceplate, then touch the disc tab soft-key and then the view video soft-key. • viewing a dvd on the touch-screen radio screen is not available in all states/provinces, and the vehicle must be stopped, and the shift leve...

  • Page 363

    When connecting an external source to the aux input, be sure to follow the standard color coding for the ves™ jacks: note: certain high-end video games, such as playsta- tion3 and xbox360 will exceed the power limit of the vehicle’s power inverter. Refer to the power inverter section in your vehicle...

  • Page 364

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. Touch the 1 or 2 based on the headphone c...

  • Page 365

    Listen to an audio source on channel 2 while a video is playing on channel 1 ensure the remote control and headphone switch is on channel 2. Using the remote control 1. Press the mode button on the remote control and the mode select screen will display, unless a video is playing then only a small ba...

  • Page 366

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. To listen to an audio source on channel 2...

  • Page 367

    Important notes for single video screen system • ves™ is able to transmit two channels of stereo audio simultaneously. • in split screen mode the left side equates to channel 1 and right side equates to channel 2. • if a video source is selected on channel 1, then channel 2 is for audio only. Select...

  • Page 368

    Using the remote control 1. Press the mode button on the remote control. 2. While looking at screen 1, highlight disc by either pressing up/down/left/right buttons or by repeatedly pressing the mode button, then press enter. Note: • channel/screen 1 select mode information is shown on the left side ...

  • Page 369

    3. Touch the 1 or 2 soft-key based on the channel you want to change and then the disc soft-key in the media column. To exit touch the back arrow at the top left of the screen. Note: • to view a dvd on the radio press the radio/media hard-key, on the radio faceplate, then touch the disc tab soft-key...

  • Page 370

    Remote control controls and indicators 1. Power – turns the screen and wireless headphone transmitter for the selected channel on or off. To hear audio while the screen is closed, press the power button to turn the headphone transmitter on. 2. Channel selector indicators – when a button is pressed, ...

  • Page 371

    6. 䉲 / prev – in radio modes, press to select to the previous station. In disc modes, press to advance to the start of the current or previous audio track or video chapter. In menu modes, use to navigate in the menu. 7. Menu – press to return to the main menu of a dvd disc, to select a satellite aud...

  • Page 372

    And the disc is stopped, press the setup button to access the dvd setup menu. (see the dvd setup menu of this manual.) 16. Back – when navigating in menu mode, press to return to the previous screen. When navigating a dvds disc menu, the operation depends on the disc’s contents. 17. 䉳䉳 – in radio mo...

  • Page 373

    Locking the remote control all remote control functionality can be disabled as a parental control feature. • to disable the remote control from making any changes, press the video lock button add follow the radio’s instructions (select menu, rear ves, lock). If the vehicle is not equipped with a dvd...

  • Page 374

    Headphones operation the headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some headphone audio coverage to allow them to adjust the headphone volume for the young rear seat occupants that may not be able to do so for ...

  • Page 375

    Controls the headphone power indicator and controls are located on the right ear cup. Note: the rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video sys...

  • Page 376

    Replacing the batteries each set of headphones requires two aaa batteries for operation. To replace the batteries: • locate the battery compartment on the left ear cup of the headphones, and then slide the battery cover downward. • replace the batteries, making sure to orient them according to the p...

  • Page 377

    Nature whatsoever. Some states and jurisdictions may not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights. You may also have other rights, which vary from jurisdiction to jurisdiction...

  • Page 378

    Selected radio mode. When shared, the radio has priority over the ves™ or all radio modes (fm, am). The ves™ has the ability to switch tuner (am/fm), seek, scan, tune, and recall presets in radio modes as long as it is not in shared mode. When in shared disc both the radio and the ves™ have control ...

  • Page 379

    5. Channel 2 shared status 6. Channel 2 audio only/mute 7. Channel 1 enter button action 8. Channel 2 enter button action 9. Clock 10. Video lock 11. Not available / error 12. Disc changer status numeric keypad menu numeric keypad menu 4 understanding your instrument panel 377.

  • Page 380

    When the display for either channel 1 or channel 2 shows direct tune, pressing the remote control’s enter button activates a numeric keypad menu. This screen makes it easy to enter a specific tuner frequency, satellite channel, or track number. To enter the desired digit: 1. Press the remote control...

  • Page 381

    Disc menu when listening to a cd audio or cd data disc, pressing the remote control’s menu button displays a list of all commands which control playback of the disc. Using the options you can activate or cancel scan play and random play. Display settings when watching a video source (dvd video with ...

  • Page 382

    Settings are already set for optimum viewing, so there is no need to change these settings under normal circum- stances. To change the settings, press the remote control’s navi- gation buttons ( 䉱 , 䉲 ) to select an item, then press the remote control’s navigation buttons ( 䉴 , 䉳 ) to change the val...

  • Page 383

    Disc formats the ves™ dvd player is capable of playing the follow- ing types of discs (12 mm or 8 mm diameter): • dvd-video discs (mpeg-2 video compression) (see notes about dvd region codes) • dvd-audio discs (2 channel audio output only) • audio compact discs (cds) • cd data discs with mp3 and wma...

  • Page 384

    If you record a disc using a personal computer, there may be cases where the ves™ dvd player may not be able to play some or the entire disc, even if it is recorded in a compatible format and is playable on other players. To help avoid playback problems, use the following guide- lines when recording...

  • Page 385

    • the dvd player always uses the file extension to determine the audio format, so mp3 files must always end with the extension ⬙ .Mp3 ⬙ or ⬙ .Mp3 ⬙ and wma files must always end with the extension ⬙ .Wma ⬙ or ⬙ .Wma ⬙ . To prevent incorrect playback, do not use these extensions for any other types o...

  • Page 386

    And the disc is automatically ejected. A dirty, damaged, or incompatible disc format are all potential causes for a ⬙ disc error ⬙ message. If a disc has a damaged track which results in audible or visible errors that persists for 2.0 seconds, the dvd player will attempt to continue playing the disc...

  • Page 387

    All of the language settings have a special ⬙ other ⬙ setting to accommodate languages other than japanese or eng- lish. These languages are selected using a special four- digit code. To enter a new language code, activate the dvd setup menu and follow these additional instructions: • using the remo...

  • Page 388

    Them where lower numbers are designated for all audi- ences and higher numbers are designated for more adult audiences. When a dvd-video disc is loaded, its rating is compared to the setting in the dvd player. If the rating of the disc is higher than the setting in the player, a password screen is d...

  • Page 389

    To set the password, activate the dvd setup menu and follow these additional instructions: • using the remote control left and right cursor but- tons, select the rating tab. • highlight ⬙ change password ⬙ , and then press the remote control’s enter button. • enter the current password. Select a dig...

  • Page 390

    To set the rating, activate the dvd setup menu and follow these additional instructions: • using the remote control’s left and right cursor buttons, select the rating tab. • highlight ⬙ change rating ⬙ , and then press the remote control’s enter button. • enter the current password. Select a digit, ...

  • Page 391

    General information this system complies with part 15 of the fcc operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Harman kardon 姞 l...

  • Page 392

    Aux input; and is activated through the electronic vehicle information center (evic). Refer to “driver- selectable surround sound (dss)” under “electronic vehicle information center (evic)” in “understanding your instrument panel”. Selecting “audio surround” through the dss modes activates the harma...

  • Page 393

    The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will ...

  • Page 394

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 395

    Dual-zone automatic temperature control (atc) — if equipped • the automatic temperature control (atc) allows both driver and front passenger seat occupants to select individual comfort settings. • when occupants in the vehicle select an auto mode operation, auto blower operation is set by using a pu...

  • Page 396

    2. Recirculation control button press and release to change the current setting, the indicator illuminates when on. 3. Left front seat occupant temperature display this display shows the temperature setting for the left front seat occupant. 4. Mode display this display shows the current mode selecti...

  • Page 397

    11. Blower control there are seven blower speeds, the blower speed in- creases as you move the control to the right from the lowest blower setting. Performing this function will cause the atc to switch into manual mode. 12. Climate control on/off button press and release this button to turn the clim...

  • Page 398

    3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically. Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system auto...

  • Page 399

    The blower fan speed can be set to any fixed speed by adjusting the blower control outer dial. The fan will now operate at a fixed speed until additional speeds are selected. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode. The operator...

  • Page 400

    Defrost mode air comes from the windshield and side window demist outlets. Use defrost mode with maximum temperature settings for best windshield and side win- dow defrosting. When the defrost mode is selected, the blower will automatically default to medium-high unless the blower is controlled manu...

  • Page 401

    Note: in cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation mode is not allowed in the floor/defrost mix and defrost modes to improve window clearing operation. Recirculation will be disabled automatically if these modes are selected. Operating tips windo...

  • Page 402

    Summer operation note: in some cases during high temperature trailer tow operation the air conditioning system performance may be reduced. This is to help protect the engine from overheating during the high load condition. Your air conditioning system is also equipped with an automatic recirculation...

  • Page 403

    Operating tips chart 4 understanding your instrument panel 401.

  • Page 405: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 407 ▫ automatic transmission . . . . . . . . . . . . . . . 407 ▫ keyless enter-n-go . . . . . . . . . . . . . . . . . . . 408 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 409 ▫ extreme cold w...

  • Page 406

    ▫ active damping system . . . . . . . . . . . . . . . 426 䡵 driving through water . . . . . . . . . . . . . . . . . 426 ▫ flowing/rising water . . . . . . . . . . . . . . . . . 427 䡵 power steering . . . . . . . . . . . . . . . . . . . . . . . 429 䡵 parking brake . . . . . . . . . . . . . . . . . . ...

  • Page 407

    ▫ compact spare tire – if equipped . . . . . . . . 455 ▫ full size spare – if equipped . . . . . . . . . . . . 457 ▫ limited-use spare – if equipped . . . . . . . . . 457 ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . 458 ▫ tread wear indicators . . . . . . . . . . . . . . . . . 458 ▫...

  • Page 408

    䡵 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . 479 ▫ common towing definitions . . . . . . . . . . . . 480 ▫ trailer hitch classification . . . . . . . . . . . . . . 482 ▫ trailer towing weights (maximum trailer weight ratings) . . . . . . . . 483 ▫ trailer and tongue weight . . . ...

  • Page 409

    Starting procedures before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your ve...

  • Page 410

    Caution! (continued) • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle speed. • do not shift from reverse, park, or neutral into any forward gear when the engine is above idle speed. • before shifting into any gear, make sure your foot is fir...

  • Page 411

    Installing and removing the engine start/stop button installing the button 1. Remove the key fob from the ignition switch. 2. Insert the engine start/stop button into the ignition switch with the lettering facing up and readable. 3. Press firmly on the center of the button to secure it into position...

  • Page 412

    To turn off the engine using engine start/stop button 1. Place the shift lever in park, then press and release the engine start/stop button. 2. The ignition switch will return to the off position. 3. If the shift lever is not in park, the engine start/ stop button must be held for two seconds and ve...

  • Page 413

    • press the engine start/stop button a second time to change the ignition switch to the run position (evic displays “ignition mode run”), • press the engine start/stop button a third time to return the ignition switch to the off position (evic displays “ignition mode off”). Extreme cold weather (bel...

  • Page 414

    Clearing a flooded engine (using engine start/stop button) if the engine fails to start after you have followed the “normal starting” or “extreme cold weather ⬙ proce- dures, it may be flooded. To clear any excess fuel, press and hold the brake pedal, push the accelerator pedal all the way to the fl...

  • Page 415

    Automatic transmission caution! Damage to the automatic transmission may occur if the following precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at i...

  • Page 416

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, and remove the key fob. On...

  • Page 417

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the shift lever to be placed in park before the ignition switch can be turned to the lock/ off position. The key fob can only be removed from the ignition when the ignition is in the lock/off pos...

  • Page 418

    Sport mode is only available in the “selec-track” posi- tions of track and sport. Manual shifts can be made using the autostick 威 shift control (refer to “autostick 威 ” in this section). Pressing the shift paddles (-/+) while in the drive position, or tapping one of the steering wheel-mounted shift ...

  • Page 419

    Warning! (continued) • your vehicle could move and injure you and others if it is not completely in park. Check by trying to move the shift lever rearward (with the brake pedal released), after you have placed it in park. Make sure the transmission is in park before leaving the vehicle. • it is dang...

  • Page 420

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 421

    • with brake pedal released, verify that the shift lever will not move out of park. Reverse this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral use this range when the vehicle is standing for prolonged periods with engine runn...

  • Page 422

    When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading condi- tions, in hilly terrain, traveling into strong head winds, or while towing heavy trailers), use the “autostick 威 ” mode (refer to “autostick 威 ” in this section) to select a lower gear. Under th...

  • Page 423

    5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorize...

  • Page 424

    This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situa- tions. Operation when the shift lever is in the drive position, the transmission will operate automatically, shifting between the five av...

  • Page 425

    • you can start out in first or second gear. Tapping (+) (at a stop) will allow starting in second gear. Starting out in second gear is helpful in snowy or icy conditions. • the system will ignore attempts to upshift at too low of a vehicle speed. • avoid using speed control when autostick 威 is en- ...

  • Page 426

    Selec-track™ description selec-track™ combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance for all terrains. Selec-track™ consists of the following positions: • sport – dry weather, on-road calibration. Performance based tuning that provi...

  • Page 427

    • auto – fully automatic full time four-wheel drive operation can be used on and off road. Balances traction with seamless steering feel to provide im- proved handling and acceleration over two-wheel drive vehicles. The active suspension system will be in touring mode. • track – track road calibrati...

  • Page 428

    Active damping system this vehicle is equipped with an electronic controlled damping system. This system reduces body roll and pitch in many driving situations including cornering, accelera- tion and braking. There are 3 modes: • touring mode (available in terrain positions auto and snow) — used dur...

  • Page 429

    Flowing/rising water warning! Do not drive on, or cross, a road or a path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehic...

  • Page 430

    Caution! • driving through standing water may cause dam- age to your vehicle’s drivetrain components. Al- ways inspect your vehicle’s fluids (i.E., engine oil, transmission, axle, etc.) for signs of contamination (i.E., fluid that is milky or foamy in appearance) after driving through standing water...

  • Page 431

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 432

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the park position. The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully....

  • Page 433

    Note: • when the parking brake is applied and the transmis- sion is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that the park...

  • Page 434

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 435

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes the anti-lock brake system (abs), traction control system (tcs), brake assist system (bas), electronic roll mitigation (erm), and electronic stability control (esc). All five of th...

  • Page 436

    Differential (bld), functions similar to a limited-slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel...

  • Page 437

    Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicle speed are sufficient to potentially cause wheel lift...

  • Page 438

    Counteracting the oversteer or understeer condition. En- gine power may also be reduced to help the vehicle maintain the desired path. Esc uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not...

  • Page 439

    On this is the normal operating mode for esc. Whenever the vehicle is started, the esc system will be in this “on” mode. This mode should be used for most driving situations. Esc should only be turned to “partial off” mode for specific reasons as noted below. Partial off this mode is entered by mome...

  • Page 440

    Off” mode is overcome, turn esc back on by momen- tarily pressing the “esc off” switch. This may be done while the vehicle is in motion. Full off this mode is available in track mode only. Refer to “selec-terrain” in “starting and operating” for further information. In this mode, all tcs and esc sta...

  • Page 441

    Across an axle quite similarly to a limited slip differential. If one wheel on an axle is spinning faster than the other, the system will apply the brake of the spinning wheel and allow more engine torque to be applied to the wheel that is not spinning. To improve the vehicle’s traction when driving...

  • Page 442

    Warning! If tsc activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster ...

  • Page 443

    Note: • the “esc activation/malfunction indicator light” and the “esc off indicator light” come on momen- tarily each time the ignition switch is turned on. • each time the ignition is turned on, the esc system will be on even if it was turned off previously. • the esc system will make buzzing or cl...

  • Page 444

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 445

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ ....Blank.... ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t or s = temporary spare tire 31 = overall diameter in inches (in) 21...

  • Page 446

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 447

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 448

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 449

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Tire and loading information placard this placard tells you important information about the: ...

  • Page 450

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 451

    2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and pas- sengers from xxx lbs or xxx kg. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amou...

  • Page 452

    450 starting and operating.

  • Page 453

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 454

    Warning! (continued) • unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns...

  • Page 455

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage it. Inflation pressures specified on the placard are always cold tire inflation pressure. Cold tire inflation pressure...

  • Page 456

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 457

    Spare tire matching original equipped tire and wheel – if equipped your vehicle may be equivalent with a spare tire and wheel in look and function as the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehic...

  • Page 458

    Since this tire has limited tread life the original equip- ment tire should be repaired (or replaced) and reinstalled on your vehicle at the first opportunity. Note: the compact spare tire is to be used for rear wheel(s) only. For a flat front tire, move the rear tire to the front and use the compac...

  • Page 459

    Full size spare – if equipped the full size spare is for temporary emergency use only. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the te...

  • Page 460

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h). Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not ...

  • Page 461

    Life of tire the service life of a tire is dependent upon various factors including but not limited to: • driving style • tire pressure • distance driven warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result...

  • Page 462

    It is recommended you contact your original equipment or an authorized tire dealer with any questions you may have on tire specifications or capability. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. Warning! • do not use a tire, whee...

  • Page 463

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation ...

  • Page 464

    Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12°f (6.5°c). This means that when the outside...

  • Page 465

    For example, your vehicle has a recommended cold (parked for more than three hours) tire pressure of 33 psi (227 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressure is 28 psi (193 kpa), a tempera- ture drop to 20°f (-7°c) will decrease the tire pressure to approximately 24...

  • Page 466

    Note: • the tpms is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat ...

  • Page 467

    • various tire pressure monitoring system messages, which display in the electronic vehicle information center (evic), and a graphic displaying tire pressures • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will ill...

  • Page 468

    Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is “flashing” on the graphic display to the vehicle’s recommended cold tire pressure. The system will automatically update, the graphic dis- play of the pre...

  • Page 469

    Message will not be present, and a pressure value will be displayed instead of dashes. A system fault can occur by any of the following: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing some form of aftermarket w...

  • Page 470

    The evic will display a “service tpm system ⬙ mes- sage for three seconds and then display dashes (- -) in place of the pressure value. For each subsequent ignition switch cycle, a chime will sound, the tire pressure monitoring telltale light will flash on and off for 75 sec- onds and then remain on...

  • Page 471

    Fuel requirements 6.4l engine the 6.4l engine is designed to meet all emissions regulations and provide excel- lent fuel economy and performance when using high-quality premium unleaded gasoline with an octane rating of 91 or higher. Light spark knock at low engine speeds is not harmful to your engi...

  • Page 472

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, mtbe, and etbe. Oxygen- ates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your ve...

  • Page 473

    To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to reset the engine controller memory more extensive repairs will be required for prolo...

  • Page 474

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition malfu...

  • Page 475

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 476

    1. Press the fuel filler door release switch (located under the headlamp switch). 2. Open the fuel filler door, and remove the fuel filler cap. Fuel filler door release switch fuel filler cap 474 starting and operating.

  • Page 477

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indi- cator light (mil)” to illuminate, due to f...

  • Page 478

    • tighten the gas cap about one-quarter turn until you hear one click. This is an indication that the cap is properly tightened. • if the gas cap is not tightened properly, the mil will come on. Be sure the gas cap is tightened every time the vehicle is refueled. Emergency fuel filler door release i...

  • Page 479

    In “understanding your instrument panel” for further information. Tighten the fuel filler cap properly and press the select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. Vehicle loading certification label as required by natio...

  • Page 480

    Springs, tires, or wheels). Heavier axles or suspension components, sometimes specified by purchasers for in- creased durability, does not necessarily increase the ve- hicle’s gvwr. Tire size the tire size on the label represents the actual tire size on your vehicle. Replacement tires must be equal ...

  • Page 481

    Until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving. Improper weight distributions can have an adverse affect on the way your vehicle steers and handles, and the way the brak...

  • Page 482

    Common towing definitions the following trailer towing related definitions will assist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load ...

  • Page 483

    Tongue weight (tw) the tongue weight is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal area the frontal area is the maximum height and ...

  • Page 484

    Warning! • an improperly adjusted weight-distributing hitch system may reduce handling, stability, braking performance, and could result in an accident. • weight-distributing hitch systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputabl...

  • Page 485

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 6.4l automatic...

  • Page 486

    Never exceed the maximum tongue weight stamped on your trailer hitch. Consider the following items when computing the weight on the front/rear axles of the vehicle: • the trailer tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weigh...

  • Page 487

    Caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. Thi...

  • Page 488

    Warning! (continued) • vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle transmission in park. Always, block or ⴖ chock ⴖ the trailer wheels. • gcwr must not be exceeded. • total weight must be distributed between th...

  • Page 489

    Towing requirements – trailer brakes − do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. − an electronically actuated trailer brake controller is required when towing a trailer w...

  • Page 490

    Warning! (continued) • towing any trailer will increase your stopping distance. When towing you should allow for addi- tional space between your vehicle and the vehicle in front of you. Failure to do so could result in an accident. Towing tips note: to provide optimum towing performance and to prote...

  • Page 491

    − when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − use speed control in flat terrain and with light loads to maximize fuel efficiency. Cooling system to reduce potential for engine and transmission over- ...

  • Page 493: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . 492 䡵 if your engine overheats . . . . . . . . . . . . . . . . 492 䡵 jacking and tire changing . . . . . . . . . . . . . . . 493 ▫ run flat tires . . . . . . . . . . . . . . . . . . . . . . . 494 ▫ jack loca...

  • Page 494

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank just above the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. ...

  • Page 495

    Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads hot (h), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on hot (h), and you hear conti...

  • Page 496

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Run flat tires this vehicle is equipped with a compa...

  • Page 497

    Spare tire stowage the spare tire is stowed under the load floor in the rear cargo area and is secured to the body with a special wing nut. Preparations for jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery surfaces. Warning! Do not attempt to change a tire on the side of t...

  • Page 498

    6. Block both the front and rear of the wheel diagonally opposite of the jack- ing position. For example, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. 7. For vehicle equipped with quadra-lift 威 refer ...

  • Page 499

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. • only use the jack in the positions indicated and for lifting this vehicle during a tire change. • if working on or near a roadway, be extremely careful of motor tr...

  • Page 500

    3. Assemble the jack and jacking tools. Caution! Do not attempt to raise vehicle by jacking on loca- tions other than those indicated in the jacking in- structions for this vehicle. 4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lif...

  • Page 501

    Lift point symbol on sill molding front jacking location 6 what to do in emergencies 499.

  • Page 502

    5. For a rear tire, place the jack in the slot on the rear tie-down bracket, just forward of the rear tire (as indi- cated by the triangular lift point symbol on the sill molding). Do not raise the vehicle until you are sure the jack is fully engaged. 6. Raise the vehicle by turning the jack screw c...

  • Page 503

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 7. Remove the lug nuts and wheel. 8. Position the spare wheel/tire on the vehicle and install the lug nuts with ...

  • Page 504

    9. Lower the vehicle by turning the jack screw counter- clockwise, and remove the jack and wheel blocks. 10. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. ...

  • Page 505

    Warning! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Road tire installation 1. Mount the road tire...

  • Page 506

    5. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure that all lug nuts are properly seated against the wheel. Jump-starting if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portab...

  • Page 507

    Preparations for jump-start the battery in your vehicle is located under the passen- ger’s front seat. There are remote locations located under the hood to assist in jump-starting. Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition...

  • Page 508

    3. Remove the protective cover over the remote positive (+) battery post. Pull upward on the cover to remove it. 4. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not allow vehi...

  • Page 509

    Warning! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then st...

  • Page 510

    Freeing a stuck vehicle if the vehicle becomes stuck in snow, sand or mud, it can often be moved by a rocking motion. Move the shift lever rhythmically between drive and reverse while ap- plying slight pressure to the accelerator. In general, the least amount of accelerator pedal pressure to maintai...

  • Page 511

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 512

    Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use the following procedure to temporarily move the shift lever: 1. Firmly apply the parking brake. 2. Turn the engine off. 3. Remove the rubber liner from the cupholder (located next t...

  • Page 513

    5. Press and maintain firm pressure on the brake pedal. 6. Using the screwdriver or similar tool, press and hold the shift lock lever down. 7. Move the shift lever to the neutral position. 8. The vehicle may then be started in neutral. 9. Reinstall the shift lever override access cover and install t...

  • Page 515: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 6.4l . . . . . . . . . . . . . 515 䡵 onboard diagnostic system – obd ii . . . . . . . 516 ▫ loose fuel filler cap message . . . . . . . . . . . 516 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 516

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 538 ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . 540 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . 541 ▫ automatic transmission . . . . . . . . . . . . . . . 542 ▫ appearance care and protection from corrosion ...

  • Page 517

    Engine compartment — 6.4l 1 — totally integrated power module (fuses) 6 — air cleaner filter 2 — engine oil dipstick 7 — power steering fluid reservoir 3 — engine oil fill 8 — coolant pressure cap (radiator) 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — washer fluid reservoir 7 maintain...

  • Page 518

    Onboard diagnostic system – obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 519

    The select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the malfunction indicator light (mil). Emissions inspection and maintenance programs in some l...

  • Page 520

    4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 521

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 522

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 523

    Caution! (continued) • operating the engine with the oil levels below the safe zone, or operating with oil levels that exceed the top of the safe zone may cause engine damage. Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled main...

  • Page 524

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity sae 0w-40 engine oil is preferred for use in all operating temperatures. The engine oil filler cap also shows the reco...

  • Page 525

    Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection the manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only hi...

  • Page 526

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Caution! • do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the ...

  • Page 527

    Warning! (continued) • batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive. Keep open flames or sparks away from the battery. • do not allow vehicles to touch each other as this could establish a ground connection and personal in...

  • Page 528

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 529

    When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant, such as mopar 威 lock cyli...

  • Page 530

    Rear wiper blade removal/installation 1. Lift the pivot cap on the rear wiper arm upward, this will allow the rear wiper blade to be raised off of the liftgate glass. Note: the rear wiper arm cannot be raised fully upward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to rai...

  • Page 531

    4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade and snap the pivot cap into place. Adding washer fluid on vehicles equipped with a electronic vehicle informa- tion cente...

  • Page 532

    To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. Warning! Commercially available windshield washer solvents are flamma...

  • Page 533

    Caution! The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- ness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. Under normal operating conditions, the catalyti...

  • Page 534

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situati...

  • Page 535

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot eng...

  • Page 536

    Cooling system – drain, flush, and refill if the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant...

  • Page 537

    Adding coolant your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to 5 years or 102,000 miles (170 000 km) before replace- ment. To prevent reducing this extended maintenance period, it ...

  • Page 538

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign mat...

  • Page 539

    Coolant level the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine off and cold, the level of the engine coolant (antifreeze) in the bottle should be between the ranges indicated on the bottle. The radiator normally remains completely ...

  • Page 540

    • if frequent engine coolant (antifreeze) additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • maintain engine coolant (antifreeze) concentration at 50% hoat engine coolant (antifreeze) (...

  • Page 541

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid ...

  • Page 542

    Warning! (continued) • do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident. Front/rear axle fluid for normal service, periodic fluid level checks are not required. Whe...

  • Page 543

    Caution! Do not over tighten the plugs as it could damage then and cause them to leak. Selection of lubricant use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintain- ing your vehicle” for further information. Transfer case fluid level check inspe...

  • Page 544

    Automatic transmission selection of lubricant it is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only the manufacturer’s recommended trans- mission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicl...

  • Page 545

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check regular automatic transmission fluid level checks are not required. For this reason the dipstick is ...

  • Page 546

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 547

    Caution! (continued) • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important that the drain hol...

  • Page 548

    Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • to remove heavy soil and/or excessive brake dust, use mopar 威 wheel cleaner or equivalent or select a non-abrasive, non-...

  • Page 549

    Interior care use mopar 威 total clean or equivalent to clean fabric upholstery and carpeting. Interior trim should be cleaned starting with a damp cloth, a damp cloth with mopar 威 total clean or equiva- lent, then mopar 威 spot & stain remover or equivalent if absolutely necessary. Do not use harsh c...

  • Page 550

    When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be...

  • Page 551

    Cavity cartridge fuse mini fuse description j01 40 amp green air suspension j02 30 amp pink power liftgate mod- ule cavity cartridge fuse mini fuse description j03 30 amp pink trailer tow j04 25 amp natural driver door node j05 25 amp natural passenger door node j06 40 amp green antilock brakes pump...

  • Page 552

    Cavity cartridge fuse mini fuse description j10 30 amp pink headlamp wash relay contact j11 30 amp pink drive train control module j12 30 amp pink rear defroster j13 60 amp yellow main ignition off draw (iod) j14 20 amp blue trailer tow lamps/ park lamps j15 40 amp green front cabin fan/ blower j17 ...

  • Page 553

    Cavity cartridge fuse mini fuse description m2 20 amp yellow electronic limit slip differential/air suspension m3 20 amp yellow liftgate/headrest m5 25 amp natural 115v ac power inverter m6 20 amp yellow cigar lighter m7 20 amp yellow power outlet #2 (switchable) m8 20 amp yellow front heated seat &...

  • Page 554

    Cavity cartridge fuse mini fuse description m16 10 amp red occupant restraint controller m18 15 amp blue stop lamp m19 25 amp natural automatic shutdown 1 and 2 m20 15 amp blue instrument cluster m21 20 amp yellow automatic shutdown 3 m22 10 amp red horns (low/high) – right m23 10 amp red horns (low...

  • Page 555

    Cavity cartridge fuse mini fuse description m31 20 amp yellow backup lamps m32 10 amp red occupant restraint controller m33 10 amp red powertrain controller/ transmission controller m34 10 amp red park assist module/ climate control sys- tem module/infra red sensor/compass module m35 15 amp blue lef...

  • Page 556

    Caution! (continued) • when replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem i...

  • Page 557

    Exterior lights bulb type headlamps (low beam) . . . . . . . . . . . . . . . . . . . H11 headlamps (high beam) . . . . . . . . . . . . . . . . . . 9005 headlamps (low beam) – high intensity discharge (hid) . . . D1s (serviced at authorized dealer) front park/turn lamp . . . . . . . . . . . . . . . ....

  • Page 558

    Note: on vehicles equipped with high intensity dis- charge (hid) headlamps, when the headlamps are turned on, there is a blue hue to the lamps. This dimin- ishes and becomes more white after approximately 10 seconds, as the system charges. Halogen headlamps – if equipped 1. Open the hood. 2. Turn th...

  • Page 559

    2. Firmly grasp the bulb by the two latches and squeeze them together to unlock the bulb from the back of the front fog lamp housing. 3. Pull the bulb straight out from the keyed opening in the housing. Caution! • do not touch the new bulb with your fingers. Oil contamination will severely shorten b...

  • Page 560

    Rear tail, stop, turn signal, and backup lamps 1. Raise the liftgate. 2. Remove the two push-pins from the tail lamp housing. 3. Grasp the tail lamp and pull firmly rearward to disengage the lamp from the aperture panel. 4. Twist socket counter clockwise and remove from lamp. 5. Pull the bulb to rem...

  • Page 561

    8. Continue removing the trim. 9. Disconnect the two trim panel lights. 10. Tail lamps are now visible. Rotate socket(s) counter clockwise. 11. Remove/replace bulb(s). 12. Reinstall the socket(s) 13. Reverse process to reinstall the liftgate trim. Center high-mounted stop lamp (chmsl) the center hig...

  • Page 562

    Rear license lamp 1. Use a screw driver to gently pry against the side of the snap tab to remove the license lamp lens. 2. Pull bulb from socket. 3. Replace bulb. 4. Reinstall lens. Fluid capacities u.S. Metric fuel (approximate) 25 gallons 94 liters engine oil with filter 6.4 liter engine (sae 0w-4...

  • Page 563

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hy- brid organic additive technology) or equivalent. Engine oil for best performance and maximum protection under all types of operat- ...

  • Page 564

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 威 automatic transmission fluid or equivalent licensed atf+4 威 product. Transfer case mopar 威 nv146 transfer case fluid or equivalent. Usage of other fluid/ lubricants is not recommended. Axle differential (front...

  • Page 565: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedules . . . . . . . . . . . . . . . . . 564 ▫ required maintenance intervals . . . . . . . . . . 565 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 566

    Maintenance schedules the scheduled maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditio...

  • Page 567

    Referring to the steps described under “electronic vehicle information center (evic)/oil change required” in “understanding your instrument panel” for further in- formation. At each stop for fuel • check the engine oil level about five minutes after a fully warmed engine is shut off. Checking the oi...

  • Page 568

    6,000 miles (10,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. Odometer reading date repair order # dealer code signature, authorized service center 12,000 miles (20,000 km) or 12 months maintenance service schedule ❏ change the engine oil and engine ...

  • Page 569

    18,000 miles (30,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. Odometer reading date repair order # dealer code signature, authorized service center 24,000 miles (40,000 km) or 24 months maintenance service schedule ❏ change the engine oil and engin...

  • Page 570

    30,000 miles (50,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ replace the engine air cleaner filter. ❏ drain the transfer case and refill. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. Odometer reading date repair order...

  • Page 571

    48,000 miles (80,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake linings; replace if neces...

  • Page 572

    60,000 miles (100,000 km) or 60 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ replace the engine air cleaner filter. ❏ inspect the brake linings; replace if necessary. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change the automat...

  • Page 573

    72,000 miles (120,000 km) or 72 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake linings; replace if nece...

  • Page 574

    84,000 miles (140,000 km) or 84 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake linings; replace if nece...

  • Page 575

    96,000 miles (160,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ replace the spark plugs. ❏ inspect the bra...

  • Page 576

    108,000 miles (180,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake linings; replace if ne...

  • Page 577

    120,000 miles (200,000 km) or 120 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ replace the engine air cleaner filter. ❏ inspect the brake linings; replace if necessary. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ inspect the cv j...

  • Page 578

    132,000 miles (220,000 km) or 132 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake linings; replace if ne...

  • Page 579

    144,000 miles (240,000 km) or 144 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake linings; replace if ne...

  • Page 580

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • failure to properly inspect and mai...

  • Page 581: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581 ▫ prepare for the appointment . . . . . . . . . . . 581 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 581 ▫ be reasonable with r...

  • Page 582

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 587 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 587 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 587 ▫ temperature grades . . . . . . . . . . . . . . . . . . 58...

  • Page 583

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 584

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 585

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 586

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 587

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 588

    • service manuals these comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group llc vehicles. A complete working knowledge of the vehicle, system, and/or...

  • Page 589

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 590

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 591: Index

    Index 10

  • Page 592

    Adaptive cruise control (acc) (cruise control) . . 195 adding engine coolant (antifreeze) . . . . . . . . . . 535 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 473 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . 471 air conditioner maintenance . . . . . . . . . ...

  • Page 593

    Auxiliary power outlet . . . . . . . . . . . . . . . . . . . 252 b-pillar location . . . . . . . . . . . . . . . . . . . . . . . . 447 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524 keyless transmitter replacement (rke) . . . . . 25 belts, seat . . . . . . . . . . . . . . ...

  • Page 594

    Certification label . . . . . . . . . . . . . . . . . . . . . . . 477 chart, tire sizing . . . . . . . . . . . . . . . . . . . . . . . . 443 check engine light (malfunction indicator light) . . . . . . . . . . . . . . . 517 checking your vehicle for safety . . . . . . . . . . . . . 92 checks, safety...

  • Page 595

    Selection of coolant (antifreeze) . . . . . . . 534,560 cruise control (speed control) . . . . . . . . . . . . . . 195 cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258 customer assistance . . . . . . . . . . . . . . . . . . . . . 581 data recorder, event . . . . . . . . . . . ....

  • Page 596

    Emergency, in case of freeing vehicle when stuck . . . . . . . . . . . . . 508 hazard warning flasher . . . . . . . . . . . . . . . 492 jump starting . . . . . . . . . . . . . . . . . . . . . . . 504 tow hooks . . . . . . . . . . . . . . . . . . . . . . . . . 509 emission control system maintenance ...

  • Page 597

    Engine oil disposal . . . . . . . . . . . . . . . . . . . 522 finish care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544 flashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492 hazard warning . . . . . . . . . . . . . . . . . . . . . 492 turn signal . . . . . . . . . . ...

  • Page 598

    Fuel saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 fuel system caution . . . . . . . . . . . . . . . . . . . . . 475 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548 garage door opener (homelink®) . . . . . . . . . . . 236 gas cap (fuel filler cap) . . ...

  • Page 599

    Homelink® (garage door opener) transmitter . . 236 hood release . . . . . . . . . . . . . . . . . . . . . . . . . . 173 ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12,14 ignition key removal . . . . . . . . ....

  • Page 600

    Lead free gasoline . . . . . . . . . . . . . . . . . . . . . . 469 leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459 liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 liftgate fl...

  • Page 601

    Service engine soon (malfunction indicator) . . . . . . . . . . . . . . . . 279 side marker . . . . . . . . . . . . . . . . . . . . . . . . 558 smartbeams . . . . . . . . . . . . . . . . . . . . . . . . 176 tire pressure monitoring (tpms) . . . . . . . . . 282 tow/haul indicator . . . . . . . . . . ...

  • Page 602

    Mode fuel saver . . . . . . . . . . . . . . . . . . . . . . . . . 305 modifications/alterations, vehicle . . . . . . . . . . . . . 8 monitor, tire pressure system . . . . . . . . . . . . . . . 462 mopar parts . . . . . . . . . . . . . . . . . . . . . . . . . 518,584 mtbe/etbe . . . . . . . . . . . ....

  • Page 603

    Paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543 paint damage . . . . . . . . . . . . . . . . . . . . . . . . . . 543 panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 park sense system, rear . . . . . . . . . . . . . . . . . . . 223 parking brake . . . ....

  • Page 604

    Rear cupholder . . . . . . . . . . . . . . . . . . . . . . . . . 258 rear park sense system . . . . . . . . . . . . . . . . . . . 223 rear seat, folding . . . . . . . . . . . . . . . . . . . . . . . 166 rear window defroster . . . . . . . . . . . . . . . . . . . 269 rear window features . . . . . . ...

  • Page 605

    Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50,94 adjustable upper shoulder anchorage . . . . . . 56 and pregnant women . . . . . . . . . . . . . . . . . . 64 child restraint . . . . . . . . . . . . . . . . . . . . . 79,87 extender . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 606

    Short message service (sms) . . . . . . . . . . . . . . . . 138 shoulder belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 side airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 signals, turn . . . . . . . . . . . . . . . . . . . 96,281,556,558 smartbeams . . . . . . ....

  • Page 607

    Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 telescoping steering column . . . . . . . . . . . . . 188,189 temperature control, automatic (atc) . . . . . . . . 393 temperature gauge, engine coolant . . . . . . . . . . 287 tether anchor, child restraint . . . . . . . . . . ....

  • Page 608

    Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483 recreational . . . . . . . . . . . . . . . . . . . . . . . . 489 weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483 towing assistance . . . . . . . . . . . . . . . . . . . . . . . 130 towing vehicle behind a motorhom...

  • Page 609

    Vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 106 variance, compass . . . . . . . . . . . . . . . . . . . . . . . 315 vehicle certification label . . . . . . . . . . . . . . . . . 477 vehicle identification number (vin) . . . . . . . . . . . . 7 vehicle loading . . . . . . . . ....

  • Page 610

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 611

    Chrysler group llc 12 wk742-126 - ad 4th edition p rinted in u.S.A..