1. DL manuals
  2. Jeep
  3. Automobile
  4. Grand Cherokee 2012
  5. Owner's Manual

Jeep Grand Cherokee 2012 Owner's Manual

Manual is about: Grand Cherokee 2012

Summary of Grand Cherokee 2012

  • Page 1

    Grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2 0 12 g ra n d c h e ro k e e 12wk741-126-aa first edition printed in u.S.A. 2 0 1 2 907713 jeep cherokee om cover.Indd 1 3/10/11 1:09 pm.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 6 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 8 䡵 vehicle ide...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle. It can go places and perform tasks t...

  • Page 7

    Note: after reviewing the owner information, it should be stored in the vehicle for convenient referenc- ing and remain with the vehicle when sold. When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained tech- nicians and genuine mopar 威 parts, and...

  • Page 8

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million a...

  • Page 9

    1 introduction 7.

  • Page 10

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 11

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 1 introduct...

  • Page 13: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 14 ▫ wireless ignition node (win) . . . . . . . . . . . . 14 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ▫ removing key fob from ignition . . . . . . . . . . 16 ▫ ...

  • Page 14

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . 26 ▫ programming additional transmitters . . . . . . 26 ▫ transmitter battery replacement . . . . . . . . . . 27 ▫ general information . . . . . . . . . . . . . . . . . . . 29 䡵 remote starting system — if equipped . . . . . . . 29 ▫ how to u...

  • Page 15

    ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . 61 ▫ supplemental active head restraints (ahr) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 ▫ enhanced seat belt use reminder system (beltalert 威 ) . . . . . . . . . . . . . . . . . . . . . . . . . 65 ▫ seat belt lock out . ...

  • Page 16

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a wireless ignition node (win) with integral ignition switch. You can insert the key fob into the ignition switch with either side up. Keyless enter-n...

  • Page 17

    Key fob the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key ...

  • Page 18

    To remove the emergency key, slide the mechanical latch at the top of the key fob sideways with your thumb and then pull the key out with your other hand. Note: you can insert the double-sided emergency key into the lock cylinders with either side up. Removing key fob from ignition place the shift l...

  • Page 19

    • the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the off position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “electronic vehi...

  • Page 20

    Warning! (continued) • do not leave the key fob in or near the vehicle, and do not leave keyless enter-n-go in the acc or on/run mode. A child could operate power win- dows, other controls, or move the vehicle. • do not leave children or animals inside parked vehicles in hot weather. Interior heat b...

  • Page 21

    Vehicle can be used to start and operate the vehicle. The system will shut the engine off in two seconds if an invalid key fob is used to start the engine. After turning the ignition switch to the on/run posi- tion, the vehicle security light will turn on for three seconds for a bulb check. If the l...

  • Page 22

    Caution! • always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unat- tended. • with keyless enter-n-go, always remember to place the ignition in off. At the time of purchase, the original owner is provided with a four-digit personal identification number (pin). Ke...

  • Page 23

    Audio and visual signals, the horn will sound, the head- lights will turn on, park lamps and/or turn signals will flash repeatedly for three minutes. If the disturbance is still present (driver’s door, passenger door, other doors, ignition) after three minutes, the headlights, park lamps and/or turn...

  • Page 24

    Exterior zone (refer to ⬙ keyless enter-n-go ⬙ in ⬙ things to know before starting your vehicle ⬙ for further informa- tion). • press the lock button on the remote keyless entry (rke) transmitter. 3. If any doors are open, close them. To disarm the system the vehicle security alarm can be disarmed u...

  • Page 25

    • when the vehicle security alarm is armed, the interior power door lock switches will not unlock the doors. The vehicle security alarm is designed to protect your vehicle; however, you can create conditions where the system will give you a false alarm. If one of the previ- ously described arming se...

  • Page 26

    Note: • the front courtesy overhead console and door cour- tesy lights will turn on if the dimmer control is in the ⬙ dome on ⬙ position (extreme top position). • the illuminated entry system will not operate if the dimmer control is in the “dome defeat” position (extreme bottom position). Remote ke...

  • Page 27

    To unlock the doors press and release the unlock button on the rke transmitter once to unlock the driver’s door or twice to unlock all doors. The turn signal lamps will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Refer to “keyless enter-n-go” under “things...

  • Page 28

    To lock the doors press and release the lock button on the rke transmit- ter to lock all doors. The turn signal lamps will flash and the horn will chirp to acknowledge the signal. Refer to “keyless enter-n-go” under “things to know before starting your vehicle” for further information. Sound horn wi...

  • Page 29

    Transmitter battery replacement the recommended replacement battery is one cr2032 battery. Note: • perchlorate material — special handling may apply. See www.Dtsc.Ca.Gov/hazardouswaste/perchlorate • do not touch the battery terminals that are on the back housing or the printed circuit board. 1. Remo...

  • Page 30

    2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. 3. Remove and replace the battery. When replacing the battery, match the + sign on the battery to the + sig...

  • Page 31

    4. To assemble the rke transmitter case, snap the two halves together. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept ...

  • Page 32

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • liftgate/flipper glass closed • hazard switch off • brake switch inactive (brake pedal not pressed) • ignition key removed from ignition switc...

  • Page 33

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 34

    • the engine can be started two consecutive times with the rke transmitter. However, the ignition must be cycled by pushing the start/stop button twice (or the ignition switch must be cycled to the on/run position) before you can repeat the start sequence for a third cycle. To exit remote start mode...

  • Page 35

    Remote start comfort systems — if equipped when remote start is activated, the heated steering wheel, and driver heated seat features will automatically turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These featu...

  • Page 36

    Warning! • for personal security and safety in the event of an accident, lock the vehicle doors when you drive, as well as when you park and leave the vehicle. • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or...

  • Page 37

    If you press the door lock switch while the key fob is in the ignition switch and the driver’s door is open, the doors will not lock. If a rear door is locked, it cannot be opened from inside the vehicle without first unlocking the door. The door may be unlocked manually by raising the lock knob. Au...

  • Page 38

    3. Repeat steps 1 and 2 for the opposite rear door. Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged (locked). Child-protection door lock location child-protection door lock functi...

  • Page 39

    Note: for emergency exit from the rear seats when the child-protection door lock system is engaged, manually raise the door lock knob to the unlocked position, roll down the window, and open the door using the outside door handle. Keyless enter-n-go™ the passive entry system is an enhancement to the...

  • Page 40

    To unlock from the driver’s side: with a valid passive entry rke transmitter within 5 ft (1.5 m) of the driver’s door handle, grab the driver’s front door handle to unlock the driver’s door automatically. The interior door panel lock knob will raise when the door is unlocked. Note: if “unlock all do...

  • Page 41

    Preventing inadvertent locking of passive entry rke transmitter in vehicle to minimize the possibility of unintentionally locking a passive entry rke transmitter inside your vehicle, the passive entry system is equipped with an automatic door unlock feature which will function if there is no key fob...

  • Page 42

    Note: if “unlock all doors 1st press” is programmed in evic, all doors will unlock when you push the button on the liftgate. If ⬙ unlock driver door 1st press ⬙ is programmed in evic, the liftgate and flipper glass will unlock when you press the button on the liftgate for further information, refer ...

  • Page 43

    Note: • after pressing the door handle lock button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • the pas...

  • Page 44

    Warning! Never leave children in a vehicle with the key in the ignition switch or leave a vehicle with keyless enter- n-go in the acc or on/run position. Occupants, particularly unattended children, can become en- trapped by the windows while operating the power window switches. Such entrapment may ...

  • Page 45

    During auto up. If this happens, pull the switch lightly to the first detent and hold it to close the window manually. Warning! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Resetting the auto up feature should the au...

  • Page 46

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 47

    Liftgate flipper glass the liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. Note: the liftgate flipper glass will not open if the liftgate is ajar. Once the liftgate flipper glass has been opened, ...

  • Page 48

    Power liftgate — if equipped the power liftgate may be opened by pulling up on the liftgate handle or by pressing the liftgate button on the remote keyless entry (rke) transmitter. Press the liftgate button on the rke transmitter twice within five seconds, to open the power liftgate. Once the liftga...

  • Page 49

    Warning! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. Note: • the power liftgate will not operate if the liftgate flipper glass is open. • the power liftgate buttons will...

  • Page 50

    • if the liftgate handle is pulled while the power liftgate is opening, the liftgate motor will disengage to allow manual operation. • if the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and the liftgate must be opened or closed manu- ally...

  • Page 51

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belts for the driver and all passengers • advanced front air bags for driver and front passen- ger • supplemental active head restraints (ahr) located on top of th...

  • Page 52

    Infant and child restraint systems. For more information on latch, refer to lower anchors and tether for children (latch). Note: the advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severit...

  • Page 53

    3. The driver and front passenger seats should be moved back as far as practical to allow the advanced front air bags room to inflate. 4. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between...

  • Page 54

    Warning! (continued) • supplemental side air bag inflatable curtain (sabic) and seat-mounted side air bags (sab) also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • in a collision, you and your passengers can suffer much greater injuries if you...

  • Page 55

    Warning! • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much wo...

  • Page 56

    2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “cli...

  • Page 57

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you properly. In a sudden stop...

  • Page 58

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. Wa...

  • Page 59

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. In...

  • Page 60

    Adjustable upper shoulder belt anchorage in the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Press the release button to release the anchorage, and then move it up or down to the position that fits you best. As a guide, if yo...

  • Page 61

    Additional information, refer to “installing child re- straints using the vehicle seat belt” under the “child restraints” section. The chart below defines the type of feature for each seating position. Driver center passenger first row n/a n/a alr second row alr alr alr third row n/a n/a n/a • n/a —...

  • Page 62

    3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automati...

  • Page 63

    Seat belt pretensioners the seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by assuring that the belt is tight about the oc...

  • Page 64

    However if during a front impact, a secondary rear impact occurs, the ahr may deploy based on several factors, including the severity and type of the impact. Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed i...

  • Page 65

    1. Grasp the deployed ahr from the rear seat. 2. Position the hands on the top of the deployed ahr at a comfortable position. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand positioning points on ahr 1 — downward movement 2 — rearward moveme...

  • Page 66

    4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an autho...

  • Page 67

    Enhanced seat belt use reminder system (beltalert 姞 ) beltalert 威 is a feature intended to remind the driver and front passenger (if equipped with front passenger beltalert 威 ) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unb...

  • Page 68

    Seat belt lock out the center rear seat belt system has a lock out feature that will not allow you to extract the center webbing unless the rear seat upper latch is engaged. Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the moth...

  • Page 69

    Instrument panel, above the glove compartment. The words srs airbag are embossed on the air bag covers. Note: the driver and front passenger advanced front air bags are certified to the new federal regulations for advanced air bags. The advanced front air bags have a multistage inflator design. This...

  • Page 70

    This vehicle is equipped with supplemental seat- mounted side air bags (sab) to provide enhanced protection for an occupant during a side impact. The supplemental seat-mounted side air bags are located in the outboard side of the front seats. Note: • air bag covers may not be obvious in the interior...

  • Page 71

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 72

    Supplemental seat-mounted side air bags (sab) supplemental seat-mounted side air bags (sab) may provide enhanced protection to help protect an occupant during a side impact. The sab is marked with an air bag label sewn into the outboard side of the front seats. When the air bag deploys, it opens the...

  • Page 73

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the sab and sabic air bags during deployment could cause you to be severely injured or killed. • should a vehicle rollover occur, the pretensioners and/or sab and sabic ...

  • Page 74

    Warning! (continued) • do not use accessory seat covers or place objects between you and the side air bags; the perfor- mance could be adversely affected and/or objects could be pushed into you, causing serious injury. • your vehicle is equipped with sabic air bags, do not have any accessory items i...

  • Page 75

    Advanced front air bags are designed to provide addi- tional protection by supplementing the seat belts in certain frontal collisions depending on several factors, including the severity and type of collision. Advanced front air bags are not expected to reduce the risk of injury in rear, side, or ro...

  • Page 76

    Also, the orc turns on the air bag warning light in the instrument panel for approxi- mately four to eight seconds for a self-check when the ignition is first turned on. After the self-check, the air bag warning light will turn off. If the orc detects a malfunction in any part of the system, it turn...

  • Page 77

    Are possible, based on the collision type and severity. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The air bags fully inflate in about 50 to 70 milliseconds. This is about half of the...

  • Page 78

    A quantity of non-toxic gas is generated to inflate the sabic. The inflating sabic pushes the outside edge of the headliner out of the way and covers the window. The sabic inflates in about 30 milliseconds (about one- quarter of the time that it takes to blink your eyes) with enough force to injure ...

  • Page 79

    • unlock the doors automatically. In order to reset the enhanced accident response system functions after an event, the ignition switch must be changed from ign on to ign off. If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or ...

  • Page 80

    Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retrac- tor assemblies replaced by an authorized dealer im- mediately. Also, have the occupant restraint con- troller (orc) system servi...

  • Page 81

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, includ- ing your trim cover and cushio...

  • Page 82

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of t...

  • Page 83

    In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. Child restraints everyone in your vehicle needs to be buckled up all the time, including babies and children. Ev...

  • Page 84

    Facing child safety seat. Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. The infant carrier is only used rearward-facing in the vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrie...

  • Page 85

    Here are some tips for getting the most out of your child restraint: • before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. Chrysler group llc also recommends that you try a child restraint in the vehicle seats where you will use...

  • Page 86

    Note: for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck. Cana- dian residents should refer to transport canada’s web- site for additional information: http://www.Tc.Gc.Ca/ roadsafety/safedrivers/childsafety/index.Htm older children and child restraints children who are t...

  • Page 87

    • check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • if the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind the back. Lower anchors and tet...

  • Page 88

    The rear outboard seating positions have lower anchorages capable of accommodating latch-compatible child seats having flexible, webbing-mounted lower attachments and child seats with fixed lower attachments. The rear seat lower anchors can be readily identified by the symbol located on the seatback...

  • Page 89

    In addition, there are top tether strap anchorages behind each rear seating position located on the back of the seat. To access the top tether strap anchorages behind the rear seat, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchorages. Latch anchora...

  • Page 90

    Warning! Do not use the cargo tie downs located on the load floor. Improper usage of the tether can lead to a failure of an infant or child restraint. The child could be badly injured or killed. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having...

  • Page 91

    Gap panel. They are not visible until you fold the gap panel down. Do not use the cargo tie down hooks located on the floor behind the seat. Finally, tighten all three straps as you push the child restraint rearward and downward into the seat, removing slack in the straps according to the child rest...

  • Page 92

    Installing a child restraint with an alr: 1. To install a child restraint with alr, first, pull enough of the seat belt webbing from the retractor to route it through the belt path of the child restraint. Slide the latch plate into the buckle until you hear a “click.” next, extract all the seat belt...

  • Page 93

    Pull down on the tether to unhook it from the plastic seat backing, then raise the armrest and attach the tether hook to the strap located on the front of the arm rest. For center seating position route the tether strap over the seatback and headrest then attach the hook to the tether anchor located...

  • Page 94

    Top tether strap anchorage (located on seatback) top tether strap mounting 92 things to know before starting your vehicle.

  • Page 95

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly be- hind the child seat to secure a child restraint top tether strap. • do not use the cargo tie downs located on the load floor. Improper usag...

  • Page 96

    While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving t...

  • Page 97

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), whi...

  • Page 98

    Vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger c...

  • Page 99

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 100

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 101: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 ▫ inside day/night mirror . . . . . . . . . . . . . . . 107 ▫ automatic dimming mirror — if equipped . . 108 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . 109 ▫ o...

  • Page 102

    ▫ phone call features . . . . . . . . . . . . . . . . . . 130 ▫ uconnect™ phone features . . . . . . . . . . . . . 133 ▫ advanced phone connectivity . . . . . . . . . . . 137 ▫ things you should know about your uconnect™ phone . . . . . . . . . . . . . . . . . . . . 139 ▫ general information . . . ....

  • Page 103

    䡵 driver memory seat — if equipped . . . . . . . . 174 ▫ setting memory positions and linking remote keyless entry transmitter to memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 ▫ memory position recall . . . . . . . . . . . . . . . . 176 ▫ to disable a rke transmitter linked to mem...

  • Page 104

    ▫ lane change assist . . . . . . . . . . . . . . . . . . . 188 ▫ flash-to-pass . . . . . . . . . . . . . . . . . . . . . . . 188 ▫ high/low beam switch . . . . . . . . . . . . . . . 189 䡵 windshield wipers and washers . . . . . . . . . . 189 ▫ windshield wiper operation . . . . . . . . . . . . 190 ▫...

  • Page 105

    ▫ to cancel . . . . . . . . . . . . . . . . . . . . . . . . . . 207 ▫ to turn off . . . . . . . . . . . . . . . . . . . . . . . . 208 ▫ to resume speed . . . . . . . . . . . . . . . . . . . . 208 ▫ to vary the speed setting . . . . . . . . . . . . . . 209 ▫ setting the following distance in acc . . ...

  • Page 106

    ▫ turning parkview 威 on or off — without navigation/multimedia radio . . . . . . . . . . . 240 䡵 overhead console . . . . . . . . . . . . . . . . . . . . . 240 ▫ front map/reading lights . . . . . . . . . . . . . 240 ▫ courtesy lights . . . . . . . . . . . . . . . . . . . . . 241 ▫ sunglass bin door...

  • Page 107

    䡵 commandview 威 sunroof with power shade — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 255 ▫ opening sunroof — express . . . . . . . . . . . . 256 ▫ opening sunroof — manual mode . . . . . . . . 256 ▫ closing sunroof — express . . . . . . . . . . . . . 256 ▫ closing sunroof — man...

  • Page 108

    䡵 cargo area features . . . . . . . . . . . . . . . . . . . 269 ▫ rechargeable flashlight . . . . . . . . . . . . . . . . 269 ▫ cargo storage bins . . . . . . . . . . . . . . . . . . . 270 ▫ retractable cargo area cover — if equipped . . . . . . . . . . . . . . . . . . . . . . . . 271 ▫ cargo tie-do...

  • Page 109

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. The mirror should be adjusted while set in the day position (toward the windshield). Headlight glare can be reduced b...

  • Page 110

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will illuminate to indicate when the dim- ming feature is activated. The m...

  • Page 111

    Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they ...

  • Page 112

    Mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. Power mirror preselected positions can be controlled by the optional memory seat feature. Refer to “driv...

  • Page 113

    Shifted out of reverse position. Each stored memory setting will have an associated tilt mirrors in reverse position. Note: the tilt mirrors in reverse feature is not en- abled when delivered from the factory. The tilt mirrors in reverse feature can be enabled or disabled in the elec- tronic vehicle...

  • Page 114

    Blind spot monitoring — if equipped the blind spot monitoring (bsm) system uses two radar- based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle. Whe...

  • Page 115

    • the bsm system detection zone does not change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change. If the trailer or other object (i.E., bicycle, sports equipment) extends beyond the side of your v...

  • Page 116

    The bsm system notifies the driver of objects in the detection zones by illuminating the bsm warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “modes of operation” for further information. The bsm system monitors the...

  • Page 117

    Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Side monitoring rear monitoring 3 understanding the features of your vehicle 115.

  • Page 118

    Overtaking traffic if you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h)...

  • Page 119

    The bsm system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes. Stationary objects opposing traffic 3 understanding the features of your vehicle 117.

  • Page 120

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicles mirrors, glance over your shoulder...

  • Page 121

    Note: in a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When rcp is on and the vehicle is in reverse, the driver is alerted using both the visua...

  • Page 122

    Signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and detected object are present on the same side at the same time, both the visual and audio alerts will be issued. In addition to the audible a...

  • Page 123

    Phone using simple voice commands (e.G., “call” ѧ “mike” ѧ “work” or “dial” ѧ “248-555-1212”). Your mobile phone’s audio is transmitted through your vehi- cle’s audio system; the system will automatically mute your radio when using the uconnect™ phone. Note: the uconnect™ phone requires a mobile pho...

  • Page 124

    Warning! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in a collision causing serious injury or death. Uconnect™ phone button the radio or steering wheel con...

  • Page 125

    Operation voice commands can be used to operate the uconnect™ phone and to navigate through the uconnect™ phone menu structure. Voice commands are required after most uconnect™ phone prompts. You will be prompted for a specific command and then guided through the available options. • prior to giving...

  • Page 126

    Cancel command at any prompt, after the beep, you can say “cancel” and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (link) uconnect™ phone to a mobile phone to begin using your uconnect™ phone, you must pair your compatib...

  • Page 127

    Phone to use if multiple mobile phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the uconnect™ phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at an...

  • Page 128

    Add names to your uconnect™ phonebook note: adding names to the uconnect™ phonebook is recommended when the vehicle is not in motion. • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook new entry”. • when prompted, say the name of the new entry. Use of long...

  • Page 129

    • to call a name from the uconnect™ phonebook or downloaded phonebook, follow the procedure in “call by saying a name” section. • automatic download and update, if supported, begins as soon as the bluetooth 威 wireless phone connection is made to the uconnect™ phone, for example, after you start the ...

  • Page 130

    • after the “ready” prompt and the following beep, say “phonebook edit entry”. • you will then be asked for the name of the phonebook entry that you wish to edit. • next, choose the number designation (home, work, mobile, or other) that you wish to edit. • when prompted, recite the new phone number ...

  • Page 131

    • after you enter the name, the uconnect™ phone will ask you which designation you wish to delete: home, work, mobile, other, or all. Say the designation you wish to delete. • note that only the phonebook entry in the current language is deleted. • automatic downloaded phonebook entries cannot be de...

  • Page 132

    • the uconnect™ phone will then prompt you as to the number designation you wish to call. • the selected number will be dialed. Phone call features the following features can be accessed through the uconnect™ phone if the feature(s) are available on your mobile service plan. For example, if your mob...

  • Page 133

    Call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to “toggling between calls” in this section. To combine two calls, refer to “conference call” in this section. Place/retrieve a call from hold to put a call on hold, press the button until ...

  • Page 134

    Call termination to end a call in progress, momentarily press the button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is ...

  • Page 135

    Uconnect™ phone features language selection to change the language that the uconnect™ phone is using: • press the button to begin. • after the “ready” prompt and the following beep, say the name of the language you wish to switch to english, espanol, or francais. • continue to follow the system prom...

  • Page 136

    Canada and 060 for mexico). The number dialed may not be applicable with the available mobile service and area. • if supported, this number may be programmable on some systems. To do this, press the button and say “setup”, followed by “emergency”. • the uconnect™ phone does slightly lower your chanc...

  • Page 137

    Paging to learn how to page, refer to “working with automated systems”. Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the uconnect™ phone. Voice mail calling to learn how to access your voice mail, refer to “working with automate...

  • Page 138

    The uconnect™ phone will then send the corresponding phone number associated with the phonebook entry, as tones over the phone. Note: • you may not hear all of the tones due to mobile phone network configurations. This is normal. • some paging and voice mail systems have system time out settings tha...

  • Page 139

    Dialing using the mobile phone keypad you can dial a phone number with your mobile phone keypad and still use the uconnect™ phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired bluetooth 威 mobil...

  • Page 140

    From your uconnect™ phone paired mobile phone to the uconnect™ phone or vice versa, press the button and say “transfer call”. Connect or disconnect link between the uconnect™ phone and mobile phone your mobile phone can be paired with many different electronic devices, but can only be actively “conn...

  • Page 141

    • the selected phone will be used for the next phone call. If the selected phone is not available, the uconnect™ phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m)) the vehicle. Delete uconnect™ phone paired mobile phones • press the button to ...

  • Page 142

    You can either press the uconnect™ phone button to restore the factory setting or repeat the words and phrases when prompted by the uconnect™ phone. For best results, the voice training session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blow...

  • Page 143

    • fully closed windows, • dry weather condition. • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, the system may not always work for some. • when navigating through an automated system such as voice mail, or when sending a page, at the...

  • Page 144

    • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect™ phone. • echo at the phone far end can sometimes be reduced by lowering the in-veh...

  • Page 145

    Send messages: you can send messages using uconnect™ phone. To send a new message: • press the button. • after the “ready” prompt and the following beep, say “sms send” or “send message.” • you can either say the message you wish to send or say “list messages.” there are 20 preset messages. To send ...

  • Page 146

    16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and th...

  • Page 147

    3 understanding the features of your vehicle 145.

  • Page 148

    146 understanding the features of your vehicle.

  • Page 149

    3 understanding the features of your vehicle 147.

  • Page 150

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 148 unders...

  • Page 151

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

  • Page 152

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 153

    If you ever wish to interrupt the system while it lists options, press the voice command button, listen for the beep, and say your command. Pressing the voice command button while the system is speaking is known as “barging in.” the system will be interrupted, and after the beep, you can add or chan...

  • Page 154

    Changing the volume 1. Start a dialogue by pressing the voice command button. 2. Say a command (e.G., “help”). 3. Use the on/off volume rotary knob to adjust the volume to a comfortable level while the voice command system is speaking. Please note the volume setting for voice command is different th...

  • Page 155

    • “next station” (to select the next station) • “previous station” (to select the previous station) • “menu radio” (to switch to the radio menu) • “main menu” (to switch to the main menu) satellite radio to switch to satellite radio mode, say “sat” or “satellite radio”. In this mode, you may say the...

  • Page 156

    Memo to switch to the voice recorder mode, say “memo”. In this mode, you may say the following commands: • “new memo” (to record a new memo) — during the recording, you may press the voice command button to stop recording. You proceed by saying one of the following commands: − “save” (to save the me...

  • Page 157

    • “language spanish” • “tutorial” • “voice training” note: keep in mind that you have to press the voice command button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers ...

  • Page 158

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • be sure everyone in your vehicle is in a seat and using a seat belt properl...

  • Page 159

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 160

    Warning! (continued) • do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Caution! Do not place any article under a power seat or impede its abili...

  • Page 161

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 162

    Power lumbar — if equipped vehicles equipped with power driver or passenger seats are also equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat. Push the switch forward to increase the lumbar support. Push the switch rearward to decrease the lumbar su...

  • Page 163

    Manual front seats forward/rearward adjustment some models may be equipped with manual front driver or passenger seats. The seats can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor. While sitting in the seat, lift up on the bar located under t...

  • Page 164

    Manual front passenger seatback adjustment — recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired position and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the sea...

  • Page 165

    Heated seats — if equipped on some models, the front and rear seats may be equipped with heaters in both the seat cushions and seatbacks. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- ha...

  • Page 166

    Programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to know before starting your vehicle” for further informa- tion. Front heated seats there are two heated seat switches that allow the driver and passenger to operate the seats independently. The c...

  • Page 167

    You can choose from high, low or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high-level heating. Press the switch a second time to select low-l...

  • Page 168

    Ventilated seats — if equipped on some models, both the driver and passenger seats are ventilated. Located in the seat cushion and seatback are small fans that draw the air from the passenger compart- ment and blow air through fine perforations in the seat cover to help keep the driver and front pas...

  • Page 169

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 170

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. For comfort the active head restraints can be tilted forward and rearward. To tilt the head restrain...

  • Page 171

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 172

    Warning! (continued) • active head restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the ac- tive head restraint ensure that all cargo is se- cured, as loose cargo could contact the active head restraint during sudden st...

  • Page 173

    Warning! Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure the outboard head re- straints are in their upright positions when the seat is to be occupied. Note: for proper routing of a child seat tether refer to ...

  • Page 174

    Note: • do not fold the 60% rear seat down with the left outboard or rear center seat belt buckled. • do not fold the 40% rear seat down with the right outboard seat belt buckled. 2. Fold the rear seat completely forward. To raise rear seat raise the rear seatback and lock it into place. If interfer...

  • Page 175

    Warning! (continued) • the cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in a collision. Children should be seated and using the pro...

  • Page 176

    Driver memory seat — if equipped once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable steering wheel posi- tion (if equipped), and the radio station preset settings. Your remote keyless entry (rke) transmi...

  • Page 177

    Setting memory positions and linking remote keyless entry transmitter to memory note: each time the s (set) button and a numbered button 1 or 2 are pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key, and turn the ignition switch to the on/run posit...

  • Page 178

    To “electronic vehicle information center (evic)/ customer-programmable features” in “understanding your instrument panel” for further information. 12. Repeat the above steps to set the next memory position, using the other numbered memory button, or to link another rke transmitter to memory. Memory...

  • Page 179

    3. Press and release the memory s (set) button located on the driver’s door. 4. Within five seconds, press and release memory button 1 on the driver’s door. 5. Within five seconds, press and release the unlock button on the rke transmitter. To disable another rke transmitter linked to either memory ...

  • Page 180

    Driving position when the key is placed into the ignition, and turned out of the lock position toward the acc/on position. The easy entry/exit feature will be automatically dis- abled if the seat is already positioned closer than 0.9 in (23 mm) forward of the rear stop. At this position, there is no...

  • Page 181

    2. Reach under the hood, move safety latch to the left and lift the hood. Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. Warning! Be sure the hood is fully latched before driving your vehic...

  • Page 182

    Lights headlight switch the headlight switch is located on the left side of the instrument panel, next to the steering wheel. The head- light switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped). To turn on the headlights...

  • Page 183

    Caution! Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses. Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to...

  • Page 184

    Note: when your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “lights” in this section for further information. Smartbeam™ — if equipped the smartbeam™ system provides increased forward lighting at night by automa...

  • Page 185

    2. Push back on the multifunction lever once again to reactivate the system. Note: broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, e...

  • Page 186

    The headlight delay time is programmable on vehicles equipped with an electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)/customer-programmable features” in “under- standing your instrument panel” for further information. Parking lights and panel ligh...

  • Page 187

    Interior lights courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the headlight switch) is rotated to the its farthest upward position, or if equipped, when the unlock button is pressed on the remote keyless entry (rk...

  • Page 188

    Lights-on reminder if the headlights, parking lights, or cargo lights are left on after the ignition is turned off, a chime will sound when the driver’s door is opened. Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. I...

  • Page 189

    Each light can be turned on by pressing a switch on either side of the console. These buttons are backlit for night time visibility. To turn the lights off, press the switch a second time. The lights will also turn on when the unlock button on the remote keyless entry (rke) is pressed. Ambient light...

  • Page 190

    Multifunction lever the multifunction lever is located on the left side of the steering column. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light re...

  • Page 191

    High/low beam switch push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off. Windshield wipers and washers the windshield wiper/washer control...

  • Page 192

    Windshield wiper operation rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation. Caution! Always remove any buildup of snow that prevents the windshield wiper blades fro...

  • Page 193

    Note: if the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield washer operation to use the washer, push on the end of the lever (toward the steering wheel) and hold while spray is desired. If the lever is pushed while in the intermittent setting, the wipers will t...

  • Page 194

    Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist use the mist...

  • Page 195

    The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position 1 is the least sensitive, and wiper delay position 4 is the most sensi- tive. Setting 3 should be used for normal rain conditions. Settings 1 and 2 can be used if the driver desires less wiper sensitivit...

  • Page 196

    • transmission in neutral position — when the ignition is on, and the transmission is in the neu- tral position, the rain sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 5 mph (8 km/h), or the shift lever is moved out of the neutral position. Tilt/teles...

  • Page 197

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this war...

  • Page 198

    Note: for vehicles equipped with driver memory seat, you can use your remote keyless entry (rke) transmitter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to pre-programmed positions. Refer to “driver memory seat” in this section for further infor...

  • Page 199

    Note: the engine must be running for the heated steering wheel to operate. Vehicles equipped with remote start on models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to kn...

  • Page 200

    The electronic speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic ...

  • Page 201

    To set a desired speed turn the electronic speed control on. When the vehicle has reached the desired speed, press the set (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. Note: the vehicle should be traveling at a steady speed and on level ground b...

  • Page 202

    To accelerate for passing press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using electronic speed control on hills the transmission may downshift on hills to maintain the vehicle set speed. Note: the electronic speed control system ma...

  • Page 203

    Note: • if the sensor does not detect a vehicle ahead of you, acc will maintain a fixed set speed. • if the acc sensor detects a vehicle ahead, acc will apply limited braking or acceleration (not to exceed the original set speed) automatically to maintain a preset following distance, while matching ...

  • Page 204

    Warning! (continued) − cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions. − does not predict the lane curvature or the move- ment of preceding vehicles and will not compensate for such changes. − does not always fully recogniz...

  • Page 205

    The cruise control system has two control modes: • adaptive cruise control mode for maintaining an appropriate distance between vehicles. • normal (fixed speed) cruise control mode for cruising at a constant preset speed. For additional information, refer to “normal (fixed speed) cruise control mode...

  • Page 206

    Note: any chassis/suspension modifications to the vehicle will effect the performance of the adaptive cruise control. Activating adaptive cruise control (acc) you can only activate acc if the vehicle speed is above 20 mph (32 km/h). When the system is turned on and in the ready state, the electronic...

  • Page 207

    To activate push and release the on/off button. The acc menu in the evic displays “adaptive cruise ready.” to turn the system off, push and release the on/off button again. At this time, the system will turn off and the evic will display “adaptive cruise control off.” warning! Leaving the adaptive c...

  • Page 208

    To set a desired acc speed when the vehicle reaches the speed desired, push the set - button and release. The evic will display the set speed. Remove your foot from the accelerator pedal. If you do not, the vehicle may continue to accelerate beyond the set speed. If this occurs: • the message “drive...

  • Page 209

    To cancel the system will disable acc without erasing the memory if: • you softly tap the brake pedal. • you depress the brake pedal. • you press the cancel switch. • an anti-lock brake system (abs) event occurs. • a trailer sway control (tsc) event occurs. • if the transmission is shifted into neut...

  • Page 210

    Note: if acc is resumed or set with the esc/tcs off, esc will automatically be re-engaged. To turn off the system will turn off and erase the set speed in memory if: • you push the on/off button. • you turn off the ignition. • you switch to four-wheel drive low. To resume speed press the res + butto...

  • Page 211

    To vary the speed setting while acc is set, you can increase the set speed by pressing and holding the res + button. If the button is continually pressed, the set speed will continue to in- crease in 5 mph (8 km/h) increments until the button is released. The increase in set speed is reflected in th...

  • Page 212

    Setting the following distance in acc the specified following distance for acc can be set by varying the distance setting between 3 (long), 2 (me- dium), and 1 (short). Using this distance setting and the vehicle speed, acc calculates and sets the distance to the vehicle ahead. This distance setting...

  • Page 213

    To change the distance setting, press the distance button and release. Each time the button is pressed, the distance setting adjusts between long, medium, and short. If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle is detected in the same lane, the ev...

  • Page 214

    The maximum braking applied by acc is limited; how- ever, the driver can always apply the brakes manually, if necessary. Note: the brake lights will illuminate whenever the acc system applies the brakes. A proximity warning will alert the driver if acc predicts that its maximum braking level is not ...

  • Page 215

    Adaptive cruise control (acc) menu the evic displays the current acc system settings. The evic is located in the upper part of the instrument cluster between the speedometer and the tachometer. The information it displays depends on acc system status. Press the menu button (located on the steer- ing...

  • Page 216

    The acc screen will display once again if any acc activity occurs, which may include any of the following: • set speed change • distance setting change • system cancel • driver override • system off • acc proximity warning • acc unavailable warning the evic will return to the last display selected a...

  • Page 217

    Note: if the acc “clean radar sensor in front of vehicle” warning is active normal (fixed speed) cruise control is still available. For additional information refer to “normal (fixed speed) cruise control mode” in this section. If weather conditions are not a factor, the driver should examine the se...

  • Page 218

    • do not attach or install any accessories near the sensor, including transparent material or aftermarket grilles. Doing so could cause an acc system failure or malfunction. When the condition that deactivated the system is no longer present, the system will return to the “adaptive cruise control of...

  • Page 219

    Note: do not change the adjustment fasteners or pull the sensor off of the bracket. Doing so may misalign the sensor. Store the sensor and bracket assembly in a safe location. The wiring and connector must be stowed properly after the sensor and bracket assembly is removed. A connector plug is stowe...

  • Page 220

    Service acc warning if the system turns off, and the evic displays “acc/ fcw unavailable service radar sensor”, it indicates there is an internal system fault. Although the vehicle is still drivable under normal conditions, have the system checked by an authorized dealer. Precautions while driving w...

  • Page 221

    Offset driving acc may not detect a vehicle in the same lane that is offset from your direct line of travel. There will not be sufficient distance to the vehicle ahead. The offset vehicle may move in and out of the line of travel, which can cause your vehicle to brake or accelerate unexpectedly. Tur...

  • Page 222

    Using acc on hills when driving on hills, acc may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, acc perfor- mance may be limited. Lane changing acc will not detect a vehicle until it is completely in the lane in which you...

  • Page 223

    Narrow vehicles some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There will not be suffi- cient distance to the vehicle ahead. 3 understanding the features of your vehicle 221.

  • Page 224

    Stationary objects and vehicles acc does not react to stationary objects and stationary vehicles. For example, acc will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if nece...

  • Page 225

    Warning! In the normal cruise control mode, the system will not react to vehicles ahead. In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is ...

  • Page 226

    To resume press the res + button and then remove your foot from the accelerator pedal. The evic will display the last set speed. To turn off the system will turn off and erase the set speed in memory if: • you push the on/off button. • you turn off the ignition. • you engage four-wheel drive low. If...

  • Page 227

    Note: • the minimum speed for fcw activation is 10 mph (16 km/h). • when entering or driving in a curve, the fcw alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course predic- tion. This is expected and is a part of normal fcw activation and func...

  • Page 228

    Fcw settings can only be changed when the vehicle is in park. The default status of fcw is the “far” setting, this allows the system to warn you of a possible collision with the vehicle in front of you when you are farther away. This gives you the most reaction time. Changing the fcw status to the “...

  • Page 229

    Changing the fcw status to “off” prevents the system from warning you of a possible collision with the vehicle in front of you. Note: in the “off” setting fcw off will be displayed in the evic. Note: • the system will retain the last setting selected by the driver after ignition shut down. Example o...

  • Page 230

    • fcw will not react to irrelevant objects such as over- head objects, ground reflections, objects not in the path of the car, stationary objects that are far away, oncom- ing traffic, or leading vehicles with the same or higher rate of speed. • fcw will be disabled like acc below with the un- avail...

  • Page 231

    Parksense 姞 rear park assist — if equipped the parksense 威 rear park assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to parksense 威 system usage precautions for limitations of...

  • Page 232

    The parksense 威 warning display is located in the instru- ment cluster’s evic display. It provides both visual and audible warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. Parksense 姞 display when the vehicle is in reverse, the warning display will turn on ...

  • Page 233

    The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the evic display will show fewer arcs and the sound tone will change from slow, to fast, to continuous. Park assist system off slow tone 3 under...

  • Page 234

    The vehicle is close to the obstacle when the evic display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: fast tone continuous tone 232 understanding the features of your vehicle.

  • Page 235

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-39 in (200-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible alert chime none single 1/2 second tone slow fast continuous display message park assist sys- tem on warning object detected warning object ...

  • Page 236

    “electronic vehicle information center (evic)” in “un- derstanding your instrument panel” for further informa- tion. When the shift lever is moved to reverse and the system is disabled, the evic will display the “park assist system off” message for as long as the vehicle is in reverse. The parksense...

  • Page 237

    Parksense 姞 system usage precautions note: • ensure that the rear bumper is free of snow, ice, mud, dirt and debris to keep the parksense 威 system operat- ing properly. • jackhammers, large trucks, and other vibrations could affect the performance of parksense 威 . • when you turn parksense 威 off, th...

  • Page 238

    • on vehicles equipped with a tailgate, parksense 威 should be disabled when the tailgate is in the lowered or open position and the vehicle is in reverse. A lowered tailgate could provide a false indication that an obstacle is behind the vehicle. Caution! • parksense 威 is only a parking aid and it i...

  • Page 239

    Warning! (continued) • before using the parksense 威 rear park assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles becau...

  • Page 240

    When displayed, static grid lines will illustrate the width of the vehicle while a dashed center-line will indicate the center of the vehicle to assist with aligning to a hitch/ receiver. The static grid lines will show separate zones that will help indicate the distance to the rear of the vehicle. ...

  • Page 241

    Warning! Drivers must be careful when backing up even when using the parkview 威 rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your...

  • Page 242

    4. Enable or disable the rear camera feature by selecting the “enable rear camera in reverse” soft-key. 5. Press the “save” soft-key. Turning parkview 姞 on or off — without navigation/multimedia radio 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 3. Enable or disable the rear came...

  • Page 243

    To turn the lights off, press the switch a second time. The lights also turn on when a door is opened. The lights will also turn on when the unlock button on the rke is pressed. Courtesy lights the courtesy lights can be turned on by pressing the top corner of the lens. To turn the lights off, press...

  • Page 244

    Sunglass bin door at the front of the console a compartment is provided for the storage of a pair of sunglasses. The storage compart- ment access is a “push/push” design. Push the chrome pad on the door to open. Push the chrome pad on the door to close. Garage door opener — if equipped homelink 威 re...

  • Page 245

    Note: homelink 威 is disabled when the vehicle secu- rity alarm is active. Homelink 威 buttons/overhead consoles homelink 威 buttons/sunvisor/headliner 3 understanding the features of your vehicle 243.

  • Page 246

    Before you begin programming homelink 姞 be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the ...

  • Page 247

    1. Turn the ignition switch to the on/run position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink 威 button you wish to program while keeping the homelink 威 indicator light in view. 3. Simultaneously press and hold both the homelink 威 button you want to program and t...

  • Page 248

    Note: you have 30 seconds in which to initiate the next step after the learn button has been pressed. 6. Return to the vehicle and press the programmed homelink 威 button twice (holding the button for two seconds each time). If the garage door opener/device activates, programming is complete. Note: i...

  • Page 249

    4. Continue to hold both buttons and observe the indi- cator light. The homelink 威 indicator will flash slowly and then rapidly after homelink 威 has received the fre- quency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid. 5. Press and...

  • Page 250

    To pick up the signal during programming. Similar to this canadian law, some u.S. Gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. 1. Turn the ignition switc...

  • Page 251

    Reprogramming a single homelink 威 button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink 威 button until the indicator light begins to flash after 20 seconds. Do not release the but...

  • Page 252

    Troubleshooting tips if you are having trouble programming homelink 威 , here are some of the most common solutions: • replace the battery in the original hand-held transmit- ter. • press the learn button on the garage door opener to complete the training for a rolling code. • did you unplug the devi...

  • Page 253

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 254

    Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • in a collision, there is a gre...

  • Page 255

    Position. The sunroof will close fully and stop automati- cally. This is called “express close”. During express close operation, any movement of the switch will stop the sunroof. Closing sunroof — manual mode to close the sunroof, press and hold the switch in the forward position. Any release of the...

  • Page 256

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) is in certain open or partially open positions. This is a normal occur- rence a...

  • Page 257

    Commandview 姞 sunroof with power shade — if equipped the commandview 威 sunroof switch is located to the left between the sun visors on the overhead console. The power shade switch is located to the right between the sun visors on the overhead console. Warning! • never leave children in a vehicle wit...

  • Page 258

    Opening sunroof — express press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automati- cally. This is called “express open”. During express open operation, any movement of the sunroof switch ...

  • Page 259

    Opening power shade — manual mode to open the shade, press and hold the switch rearward to full open. Any release of the switch will stop the move- ment and the shade will remain in a partially opened condition until the switch is pushed and held rearward again. Closing power shade — express press t...

  • Page 260

    Open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buff...

  • Page 261

    • to ensure proper operation a mopar 威 knob and element must be used. Caution! Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by y...

  • Page 262

    In addition to the front power outlet, there is also a power outlet located in the storage area of the center console. The rear power outlet is located in the right rear cargo area. Note: the rear power outlet can be switched to “battery” powered all the time by switching the power outlet right rear...

  • Page 263

    Power outlet right rear quarter panel fuse power outlet fuse locations 1 — m7 fuse 20 a yellow power outlet right rear quarter panel 2 — m6 fuse 20 a yellow cigar lighter instrument panel 3 — m36 fuse 20 a yellow power outlet console bin 3 understanding the features of your vehicle 261.

  • Page 264

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 265

    Power inverter — if equipped there is a 115 volt, 150 watt inverter outlet located on the back of the center console to convert dc current to ac current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 watts. Certain high-end video games, su...

  • Page 266

    The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximat...

  • Page 267

    Cupholders there are two cupholders for the front seat passengers located in the center console. There are two cupholders for the rear seat passengers located in the fold-down center armrest. Front cupholder location rear cupholders 3 understanding the features of your vehicle 265.

  • Page 268

    Storage glove compartment the glove compartment is located on the right side of the instrument panel. To open the glove compartment, pull outward on the latch and lower the glove box door. Glove compartment opened glove compartment 266 understanding the features of your vehicle.

  • Page 269

    Door storage large storage areas are built into the door panels for easy access. Center console the center console contains both an upper and a lower storage area. Door panel storage storage compartment 3 understanding the features of your vehicle 267.

  • Page 270

    To open the upper storage compartment, pull upward on the small latch located on the lid. Lift upward on the larger of the latches to access the lower storage compartment. Storage compartment latches lower storage compartment 268 understanding the features of your vehicle.

  • Page 271

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injur...

  • Page 272

    To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Cargo storage bins there are four removable storage bins located in the rear cargo area. There are two storage bins located on either side of the cargo area. Three-press switch rear storage b...

  • Page 273

    Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether hook (attached to the bottom of the load floor) to the liftgate opening. Retractable cargo area cover — if equipped note: the purpose of this cover is for privac...

  • Page 274

    To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the pins on the ends of the cover into the slots in the pillar trim cover. 3. The liftgate may be opened with the cargo cover in place. Rear cargo cover 272 understanding the features of your veh...

  • Page 275

    Warning! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. D...

  • Page 276

    Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. • cargo tie-down hooks are not safe anchors for a child seat t...

  • Page 277

    Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the control lever. The control lever is located on the left side of the steering column. Rotate the center portion of the lever upward to the first detent for intermittent operation and to...

  • Page 278

    If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “park” position. If the liftgate flipper glass is open, the rear window wiper/washer functionality is interrupted and the wiper stops at that “park” position. When the liftgate flipper glass is...

  • Page 279

    Roof luggage rack — if equipped the crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Note: if not equipped with crossbars, your authorized ...

  • Page 280

    Caution! • to prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without the crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other ...

  • Page 281: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 283 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 284 䡵 instrument cluster descriptions . . . . . . . . . . . 285 䡵 electronic vehicle information center (evic) . . . . . . . . . . ....

  • Page 282

    ▫ messages # . . . . . . . . . . . . . . . . . . . . . . . . . 316 ▫ turn menu off . . . . . . . . . . . . . . . . . . . . . . 317 ▫ keyless enter-n-go display — if equipped . . . . . . . . . . . . . . . . . . . . . . . . 317 ▫ compass / temperature display . . . . . . . . . 317 ▫ customer-programma...

  • Page 283

    ▫ uconnect™ multimedia (satellite radio) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 349 ▫ operating instructions (uconnect™ phone) — if equipped . . . . . . . . . . . . . . . . . . . . . . 353 䡵 ipod 威 /usb/mp3 control — if equipped . . . . . 353 ▫ connecting the ipod 威 or ext...

  • Page 284

    ▫ replacing the batteries . . . . . . . . . . . . . . . . 375 ▫ headphones operation . . . . . . . . . . . . . . . . 376 ▫ controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 377 ▫ replacing the batteries . . . . . . . . . . . . . . . . 378 ▫ unwired 威 stereo headphone lifetime limited wa...

  • Page 285

    Instrument panel features 1 — air outlet 6 — lower switch bank 11 — hood release 2 — instrument cluster 7 — hazard switch 12 — fuel door release 3 — radio 8 — storage bin 13 — headlight switch 4 — glove compartment 9 — esc button 14 — dimmer control 5 — climate controls 10 — ignition switch 4 unders...

  • Page 286

    Instrument cluster 284 understanding your instrument panel.

  • Page 287

    Instrument cluster descriptions 1. Tachometer indicates the engine speed in revolutions per minute (rpm x 1000). 2. Air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to the on/run position. If the light is either not on d...

  • Page 288

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to...

  • Page 289

    5. Tow/haul indicator light — if equipped this light will illuminate when the tow/ haul button has been selected. The tow/ haul button is located in the center of the instrument panel (below the climate controls). 6. Turn signal indicator the arrows will flash with the exterior turn signals when the...

  • Page 290

    As it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ service,...

  • Page 291

    Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped wi...

  • Page 292

    12. Park/headlight on indicator — if equipped this indicator will illuminate when the park lights or headlights are turned on. 13. Seat belt reminder light when the ignition switch is first turned to the on/run position, this light will turn on for four to eight seconds as a bulb check. During the b...

  • Page 293

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 294

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Anti-lock brake (abs) light this light monitors the anti-lock brake sy...

  • Page 295

    18. Fuel door reminder the fuel pump symbol points to the side of the vehicle where the fuel door is located. 19. Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position. 20. Electronic vehicle information center (evic) white telltale area t...

  • Page 296

    25. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or ...

  • Page 297

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • fuel economy • acc: (if equipped) • vehicle speed • trip info • terrain: (if equipped...

  • Page 298

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: up button press and release the up button to scroll up- ward through the main menus (fuel economy, vehicle info, tire psi, cruise, messages, units, system setup, vehicle speed, trip in...

  • Page 299

    Back button press the back button to scroll back to a previous menu or sub-menu. Electronic vehicle information center (evic) displays the evic display consists of three sections: 1. The top line where compass direction, odometer line and outside temperature are displayed. 2. The main display area w...

  • Page 300

    Of this message type are ⬙ turn signal on ⬙ (if a turn signal is left on) and ⬙ lights on ⬙ (if driver leaves the vehicle). • unstored messages until run these messages deal primarily with the remote start feature. This message type is displayed until the ignition is in the run state. Examples of th...

  • Page 301

    • liftglass open • left front turn signal lamp out • right front turn signal lamp out • left rear turn signal lamp out • right rear turn signal lamp out • low tire pressure • esc system off • service blind spot system • blind spot detection unavailable • blind spot system off • blind spot system una...

  • Page 302

    • sensed vehicle indicator — the system detects a slower moving vehicle in the same lane. Refer to “adaptive cruise control (acc)” in “understanding the features of your vehicle” (if equipped). • driver override — if you apply the accelerator after setting the desired speed in the acc system. Refer ...

  • Page 303

    To “adaptive cruise control (acc)” in “understand- ing the features of your vehicle” (if equipped). • cruise off when park brake is on • acc cancelled below min. Speed. • coolant low • service air suspension system • oil change due • key in ignition • lights on • key in ignition lights on • ignition...

  • Page 304

    • memory 1 profile recall • memory 2 profile recall • press brake pedal and push button to start • wrong key • damaged key • key not programmed • function currently unavailable — power liftgate • unlock to operate — power liftgate • put in park to operate — power liftgate • automatic high beams on •...

  • Page 305

    • raising vehicle ride height (with icon) • lowering vehicle ride height (with icon) • normal vehicle ride height — this message is dis- played (for 5 seconds) when the vehicle has achieved the normal vehicle ride height. • off road ride height level 1 — this message is displayed (for 5 seconds) whe...

  • Page 306

    • selected ride height not permitted — the vehicle speed is too high to enter one of the preset levels (entry/exit level/off road ride height level 1/off road ride height level 2). • air suspension system cooling down – please wait — this message is displayed if the compressor tempera- ture level is...

  • Page 307

    • electronic speed control set this light will turn on when the electronic speed control is set. For further information, refer to “electronic speed control” in “under- standing the features of your vehicle.” • adaptive cruise control (acc) on this light will turn on when the acc is on. For further ...

  • Page 308

    • if the condition persists, see your authorized dealer for service. Evic amber telltale lights this area will show reconfigurable amber caution tell- tales. These telltales include: • forward collision warning (fcw) off this light warns the driver of a potential colli- sion with the vehicle in fron...

  • Page 309

    A loose, improperly installed, or damaged fuel filler cap may also turn on the malfunction indicator light (mil). • windshield washer fluid low indicator this light will turn on to indicate the wind- shield washer fluid is low. • serv 4wd the serv 4wd light monitors the electric shift 4wd system. If...

  • Page 310

    • oil pressure warning light this telltale indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This...

  • Page 311

    Required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • engine temperature warning light this light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches h, this indicator will illuminate and...

  • Page 312

    Warning! If the transmission temperature warning light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. Engine oil change indicator system oil change due your v...

  • Page 313

    Vehicles not equipped with keyless enter-n-go 1. Turn the ignition switch to the on/run position (do not start the engine.) 2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 3. Turn the ignition switch to the off/lock position. Note: if the indicator message illuminates ...

  • Page 314

    (mds) (if equipped) allows the engine to operate on four cylinders, or if you are driving in a fuel efficient manner. This feature allows you to monitor when you are driving in a fuel efficient manner, and it can be used to modify driving habits in order to increase fuel economy. Distance to empty (...

  • Page 315

    Cruise control press and release the up or down button until ⬙ acc ⬙ (if equipped with adaptive cruise control) or ⬙ cruise ⬙ is highlighted in the evic. Status of the acc or cruise is displayed in the menu line also. Press and release the select (right arrow) button to display the following informa...

  • Page 316

    Trip info press and release the up or down button until “trip info” displays highlighted in the evic and press the select button. Press and release the up/down but- tons until one of the following trip functions displays in the evic: • trip a • trip b • elapsed time press the up/down buttons to cycl...

  • Page 317

    Down until the preferred setting is highlighted, then press and release the select button until a check-mark appears next to the setting, showing that the setting has been selected. Vehicle info (customer information features) press and release the up or down button until “vehicle info” displays in ...

  • Page 318

    • tire pressure monitor system (shows the current pres- sure of all four road tires). For additional information, refer to “tire pressure monitor system” in “starting and operating”. Note: • tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi...

  • Page 319

    Turn menu off select from main menu using the down button. Press- ing the select button blanks the menu display. Pressing any one of the four steering wheel buttons brings the menu back. Keyless enter-n-go display — if equipped when the engine start/stop button is pressed to change ignition switch p...

  • Page 320

    Metallic objects) until the cal indicator displayed in the evic turns off. The compass will now function normally. Note: a good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. Compass varia...

  • Page 321

    3. Press the down button until the “compass variance” message is displayed in the evic, then press the select button. The last variance zone number displays in the evic. 4. Press and release the select button until the proper variance zone is selected, according to the map. 5. Press and release the ...

  • Page 322

    Out of park or the vehicle begins moving, a warning message setup not available, is followed in three seconds by, vehicle not in park. Press and release the up or down button until setup displays in the evic. Use the up or down button to display one of the following choices. Select language when in ...

  • Page 323

    Remote unlock sequence when unlock driver door only on 1st press is selected, only the driver’s door will unlock on the first press of the rke transmitter unlock button. When driver door 1st press is selected, you must press the rke transmitter unlock button twice to unlock the passenger’s doors. Wh...

  • Page 324

    Removed showing the system has been deactivated. Refer to “driver memory seat” in “understanding the fea- tures of your vehicle.” remote start comfort sys. When this feature is selected and the remote start is activated, the heated steering wheel and driver heated seat features will automatically tu...

  • Page 325

    With or without the sound horn on lock feature selected. To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Headlamp off delay when this...

  • Page 326

    Note: the seat will return to the memorized seat location (if recall memory with remote key unlock is set to on) when the rke transmitter is used to unlock the door. Refer to “driver memory seat” in “understanding the features of your vehicle” for further information. Tilt mirror in reverse when thi...

  • Page 327

    Display fuel saver — if equipped the “eco” message is located in the compass/ temperature display; this message can be turned on or off. To make your selection, press and release the select button until a check-mark appears next to the setting, showing that the setting has been selected. Keyless ent...

  • Page 328

    Been deactivated. When this feature is deactivated, the system reverts to the standard intermittent wiper operation. Hill start assist (hsa) when this feature is selected, the hsa system is active. Refer to “electronic brake control system” in “starting and operating” for system function and operati...

  • Page 329

    Warn you of a possible collision with the vehicle in front of you when you are farther away. This gives you the most reaction time. To change the setting for more dynamic driving select the near setting. This warns you of a possible collision with the vehicle in front of you when you are much closer...

  • Page 330

    Select button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Calibrate compass refer to “compass display” for more information. Compass variance refer to “compass display” for more information...

  • Page 331

    Media center 130 (sales code res) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume contro...

  • Page 332

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 333

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 334

    Set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these butt...

  • Page 335

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 336

    Rw/ff press and hold the ff (fast forward) button and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (reverse) button works in a similar manner. Am/fm button press the button to select either am or fm mode. Set/rnd button (random play but...

  • Page 337

    • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result i...

  • Page 338

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and a...

  • Page 339

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the dis...

  • Page 340

    Operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume ...

  • Page 341

    Phone button uconnect™ phone — if equipped press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” in the uconnect™ user manual located on the dvd for further details. If your vehicle is not equipped with or this feature is not available on your vehicle, a ...

  • Page 342

    Info button press the info button for an rds station (one with call letters displayed). The radio will return a radio text message broadcast from an fm station (fm mode only). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the directi...

  • Page 343

    Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast music type inf...

  • Page 344

    Program type 16-digit character display top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a prese...

  • Page 345

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored i...

  • Page 346

    If you insert a disc with the ignition on/run and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player wil...

  • Page 347

    Rw/ff press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or another cd button is pressed. The rw (reverse) button works in a similar manner. Am/fm button press the button to select either am or fm mode. Set/rnd button (random play button) press t...

  • Page 348

    • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in...

  • Page 349

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and a...

  • Page 350

    List button (cd mode for mp3 play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that folde...

  • Page 351

    Time button (auxiliary mode) press this button to change the display to time of day. The time of day will display for five seconds (when the ignition is off). Uconnect™ multimedia (satellite radio) — if equipped satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide c...

  • Page 352

    Using the tune/scroll control knob until sirius id is selected. Press the tune/scroll control knob and the sirius id number will display. The sirius id number display will time out in two minutes. Press any button on the radio to exit this screen. Selecting uconnect™ multimedia (satellite) mode pres...

  • Page 353

    Seek buttons press and release the seek buttons to search for the next channel in satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without st...

  • Page 354

    Toggle the music type button again to select the music type. By pressing the seek button when the music type function is active, the radio will be tuned to the next channel with the same selected music type name. If a preset button is activated while in the music type (program type) mode, the music ...

  • Page 355

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the channels that you commit to pushbutton memory (12 satellite stations). Operating instructions (uconnect™ phone) — if equipped refer to “uconnect™ phone” in the uconnect™ ...

  • Page 356

    Connecting the ipod 姞 or external usb device use the connection cable to connect an ipod 威 or external usb device to the vehicle’s usb/aux connector port which is located in the center console or glove compart- ment. Note: the center console will have a position where the ipod 威 or consumer electron...

  • Page 357

    Note: if the audio device battery is completely dis- charged, it may not communicate with the ipod 威 /usb/ mp3 control system until a minimum charge is attained. Leaving the audio device connected to the ipod 威 /usb/ mp3 control system may charge it to the required level. Using this feature by using...

  • Page 358

    • turning it clockwise (forward) by one click, while playing a track, skips to the next track or press the vr button and say ⬙ next track ⬙ . • turning it counterclockwise (backward) by one click, will jump to the previous track in the list or press the vr button and say ⬙ previous track ⬙ • jump ba...

  • Page 359

    Scan button again. During scan mode, pressing the seek and seek >> buttons will select the previ- ous and next tracks. • rnd button (available on sales code res radio only): pressing this button toggles between shuffle on and shuffle off modes for the ipod 威 or external usb device, or press the vr b...

  • Page 360

    • preset 2 – artists • preset 3 – albums • preset 4 – genres • preset 5 – audiobooks • preset 6 – podcasts • pressing a preset button will display the current list on the top line and the first item in that list on the second line. • to exit list mode without selecting a track, press the same preset...

  • Page 361

    Warning! Do not plug in or remove the ipod 威 or external usb device while driving. Failure to follow this warning could result in an accident. Bluetooth streaming audio (btsa) music can be streamed from your cellular phone to the uconnect™ phone system. Controlling btsa using radio buttons to get in...

  • Page 362

    Previous track use the seek down button, or press the vr button on the radio and say “previous track” to jump to the previous track music on your cellular phone. Browse browsing is not available on a btsa device. Only the current song that is playing will display info. Uconnect™ multimedia video ent...

  • Page 363

    Single video screen note: typically there are two different ways to operate the features of the video entertainment system (ves)™. • the remote control • the touch-screen radio (if equipped) play a dvd 1. Press the open/close or load hard-key on the radio faceplate (touch-screen). Or press the load ...

  • Page 364

    Using the remote control 1. Press the mode button on the remote control. 2. While looking at the video screen, highlight disc by either pressing up/down/left/right buttons or by re- peatedly pressing the mode button, then press enter on the remote control. Note: the ves™ system will retain the last ...

  • Page 365

    3. Touch the 1 soft-key and then the disc soft-key in the media column. To exit touch the back arrow soft-key at the top left of the screen. Note: the “1” and “2” soft-keys are displayed for the headphone channels. Touch 1 or 2 based on which channel you want to change, select the new mode from the ...

  • Page 366

    Note: • to view a dvd on the radio press the radio/media hard-key, on the radio faceplate, then touch the disc tab soft-key and then the view video soft-key. • viewing a dvd on the touch-screen radio screen is not available in all states/provinces, and the vehicle must be stopped, and the shift leve...

  • Page 367

    When connecting an external source to the aux input, be sure to follow the standard color coding for the ves™ jacks: note: certain high-end video games, such as playsta- tion3 and xbox360 will exceed the power limit of the vehicle’s power inverter. Refer to the power inverter section in your vehicle...

  • Page 368

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. Touch the 1 or 2 based on the headphone c...

  • Page 369

    Listen to an audio source on channel 2 while a video is playing on channel 1 ensure the remote control and headphone switch is on channel 2. Using the remote control 1. Press the mode button on the remote control and the mode select screen will display, unless a video is playing then only a small ba...

  • Page 370

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. To listen to an audio source on channel 2...

  • Page 371

    Important notes for single video screen system • ves™ is able to transmit two channels of stereo audio simultaneously. • in split screen mode the left side equates to channel 1 and right side equates to channel 2. • if a video source is selected on channel 1, then channel 2 is for audio only. Select...

  • Page 372

    Using the remote control 1. Press the mode button on the remote control. 2. While looking at screen 1, highlight disc by either pressing up/down/left/right buttons or by repeatedly pressing the mode button, then press enter. Note: • channel/screen 1 select mode information is shown on the left side ...

  • Page 373

    3. Touch the 1 or 2 soft-key based on the channel you want to change and then the disc soft-key in the media column. To exit touch the back arrow at the top left of the screen. Note: • to view a dvd on the radio press the radio/media hard-key, on the radio faceplate, then touch the disc tab soft-key...

  • Page 374

    Remote control controls and indicators 1. Power – turns the screen and wireless headphone transmitter for the selected channel on or off. To hear audio while the screen is closed, press the power button to turn the headphone transmitter on. 2. Channel selector indicators – when a button is pressed, ...

  • Page 375

    6. 䉲 / prev – in radio modes, press to select to the previous station. In disc modes, press to advance to the start of the current or previous audio track or video chapter. In menu modes, use to navigate in the menu. 7. Menu – press to return to the main menu of a dvd disc, to select a satellite aud...

  • Page 376

    And the disc is stopped, press the setup button to access the dvd setup menu. (see the dvd setup menu of this manual.) 16. Back – when navigating in menu mode, press to return to the previous screen. When navigating a dvds disc menu, the operation depends on the disc’s contents. 17. 䉳䉳 – in radio mo...

  • Page 377

    Locking the remote control all remote control functionality can be disabled as a parental control feature. • to disable the remote control from making any changes, press the video lock button add follow the radio’s instructions (select menu, rear ves, lock). If the vehicle is not equipped with a dvd...

  • Page 378

    Headphones operation the headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some headphone audio coverage to allow them to adjust the headphone volume for the young rear seat occupants that may not be able to do so for ...

  • Page 379

    Controls the headphone power indicator and controls are located on the right ear cup. Note: the rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video sys...

  • Page 380

    Replacing the batteries each set of headphones requires two aaa batteries for operation. To replace the batteries: • locate the battery compartment on the left ear cup of the headphones, and then slide the battery cover downward. • replace the batteries, making sure to orient them according to the p...

  • Page 381

    Nature whatsoever. Some states and jurisdictions may not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights. You may also have other rights, which vary from jurisdiction to jurisdiction...

  • Page 382

    Selected radio mode. When shared, the radio has priority over the ves™ or all radio modes (fm, am). The ves™ has the ability to switch tuner (am/fm), seek, scan, tune, and recall presets in radio modes as long as it is not in shared mode. When in shared disc both the radio and the ves™ have control ...

  • Page 383

    5. Channel 2 shared status 6. Channel 2 audio only/mute 7. Channel 1 enter button action 8. Channel 2 enter button action 9. Clock 10. Video lock 11. Not available / error 12. Disc changer status numeric keypad menu numeric keypad menu 4 understanding your instrument panel 381.

  • Page 384

    When the display for either channel 1 or channel 2 shows direct tune, pressing the remote control’s enter button activates a numeric keypad menu. This screen makes it easy to enter a specific tuner frequency, satellite channel, or track number. To enter the desired digit: 1. Press the remote control...

  • Page 385

    Disc menu when listening to a cd audio or cd data disc, pressing the remote control’s menu button displays a list of all commands which control playback of the disc. Using the options you can activate or cancel scan play and random play. Display settings when watching a video source (dvd video with ...

  • Page 386

    Settings are already set for optimum viewing, so there is no need to change these settings under normal circum- stances. To change the settings, press the remote control’s navi- gation buttons ( 䉱 , 䉲 ) to select an item, then press the remote control’s navigation buttons ( 䉴 , 䉳 ) to change the val...

  • Page 387

    Disc formats the ves™ dvd player is capable of playing the follow- ing types of discs (12 mm or 8 mm diameter): • dvd-video discs (mpeg-2 video compression) (see notes about dvd region codes) • dvd-audio discs (2 channel audio output only) • audio compact discs (cds) • cd data discs with mp3 and wma...

  • Page 388

    If you record a disc using a personal computer, there may be cases where the ves™ dvd player may not be able to play some or the entire disc, even if it is recorded in a compatible format and is playable on other players. To help avoid playback problems, use the following guide- lines when recording...

  • Page 389

    End with the extension ⬙ .Mp3 ⬙ or ⬙ .Mp3 ⬙ and wma files must always end with the extension ⬙ .Wma ⬙ or ⬙ .Wma ⬙ . To prevent incorrect playback, do not use these extensions for any other types of files. • for mp3 files, only version 1 id3 tag data (such as artist name, track title, album, etc.) ar...

  • Page 390

    If a disc has a damaged track which results in audible or visible errors that persists for 2.0 seconds, the dvd player will attempt to continue playing the disc by skipping forward 1.0 to 3.0 seconds at a time. If the end of the disc is reached, the dvd player will return to the beginning of the dis...

  • Page 391

    All of the language settings have a special ⬙ other ⬙ setting to accommodate languages other than japanese or eng- lish. These languages are selected using a special four- digit code. To enter a new language code, activate the dvd setup menu and follow these additional instructions: • using the remo...

  • Page 392

    Them where lower numbers are designated for all audi- ences and higher numbers are designated for more adult audiences. When a dvd-video disc is loaded, its rating is compared to the setting in the dvd player. If the rating of the disc is higher than the setting in the player, a password screen is d...

  • Page 393

    To set the password, activate the dvd setup menu and follow these additional instructions: • using the remote control left and right cursor but- tons, select the rating tab. • highlight ⬙ change password ⬙ , and then press the remote control’s enter button. • enter the current password. Select a dig...

  • Page 394

    To set the rating, activate the dvd setup menu and follow these additional instructions: • using the remote control’s left and right cursor buttons, select the rating tab. • highlight ⬙ change rating ⬙ , and then press the remote control’s enter button. • enter the current password. Select a digit, ...

  • Page 395

    General information this system complies with part 15 of the fcc operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Steering wheel au...

  • Page 396

    Pressing the center button will make the radio switch between the various modes available. The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The following describes the left-hand contr...

  • Page 397

    3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become ...

  • Page 398

    Dual-zone manual heating and air conditioning the dual-zone manual climate controls allow both driver and front passenger seat occupants to select indi- vidual comfort settings. The controls consist of a series of outer rotary dials and inner push knobs. Blower control rotate this control to regulat...

  • Page 399

    • passenger temperature control rotate this control to regulate the tem- perature of the air inside the passenger compartment for the right front seat occupant. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warm...

  • Page 400

    Floor air is directed through the floor outlets with a small amount flowing through the defrost and side window demist outlets. Mix air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat to the windshiel...

  • Page 401

    Note: • continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • the use of the recirculation mode in cold or damp weather could cause windows to fog on the inside, because of moisture buildup inside the veh...

  • Page 402

    Dual-zone automatic temperature control (atc) — if equipped • the automatic temperature control (atc) allows both driver and front passenger seat occupants to select individual comfort settings. • when occupants in the vehicle select the auto mode operation, a comfort temperature can be set by using...

  • Page 403

    2. Recirculation control button press and release to change the current setting, the indicator illuminates when on. 3. Left front seat occupant temperature display this display shows the temperature setting for the left front seat occupant. 4. Mode display this display shows the current mode selecti...

  • Page 404

    11. Blower control there are seven blower speeds, the blower speed in- creases as you move the control to the right from the lowest blower setting. Performing this function will cause the atc to switch into manual mode. 12. Climate control off button press and release this button to turn the climate...

  • Page 405

    3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically. Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system auto...

  • Page 406

    Selected. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode. The operator can also select the direction of the airflow by selecting one of the following positions. Panel mode air comes from the outlets in the instrument panel. Each of the...

  • Page 407

    Temperature settings for best windshield and side win- dow defrosting. When the defrost mode is selected, the blower will automatically default to medium-high unless the blower is controlled manually. Note: while operating in the other modes, the system will not automatically sense the presence of f...

  • Page 408

    Mode is not allowed in the defrost mode to improve window clearing operation. Recirculation will be dis- abled automatically if this mode is selected. Operating tips window fogging windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperat...

  • Page 409

    Winter operation when operating the system during the winter months, make sure the air intake, located directly in front of the windshield, is free of ice, slush, snow, or other obstructions. Vacation storage anytime you store your vehicle, or keep it out of service (i.E. Vacation) for two weeks or ...

  • Page 410

    Operating tips chart 408 understanding your instrument panel.

  • Page 411: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 415 ▫ automatic transmission . . . . . . . . . . . . . . . 415 ▫ keyless enter-n-go . . . . . . . . . . . . . . . . . . . 416 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 417 ▫ extreme cold w...

  • Page 412

    䡵 four-wheel drive operation . . . . . . . . . . . . . 442 ▫ quadra-trac i 威 operating instructions/ precautions – if equipped . . . . . . . . . . . . . . 442 ▫ quadra-trac ii 威 operating instructions/ precautions – if equipped . . . . . . . . . . . . . . 442 ▫ shift positions . . . . . . . . . . . ...

  • Page 413

    䡵 power steering . . . . . . . . . . . . . . . . . . . . . . . 461 ▫ 3.6l engine . . . . . . . . . . . . . . . . . . . . . . . . 461 ▫ 5.7l engine . . . . . . . . . . . . . . . . . . . . . . . . 462 ▫ power steering fluid check . . . . . . . . . . . . . 463 䡵 multi-displacement system (mds) (if equi...

  • Page 414

    䡵 tires — general information . . . . . . . . . . . . . 489 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . 489 ▫ tire inflation pressures . . . . . . . . . . . . . . . . 490 ▫ tire pressures for high speed operation . . . 492 ▫ radial-ply tires . . . . . . . . . . . . . . . . . . . . ...

  • Page 415

    ▫ e-85 usage in non-flex fuel vehicles . . . . . . 512 ▫ mmt in gasoline . . . . . . . . . . . . . . . . . . . . 513 ▫ materials added to fuel . . . . . . . . . . . . . . . 514 ▫ fuel system cautions . . . . . . . . . . . . . . . . . 514 ▫ carbon monoxide warnings . . . . . . . . . . . . 515 䡵 flexi...

  • Page 416

    ▫ towing requirements . . . . . . . . . . . . . . . . . 534 ▫ towing tips . . . . . . . . . . . . . . . . . . . . . . . . 539 䡵 snow plow . . . . . . . . . . . . . . . . . . . . . . . . . . 540 䡵 recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . 541 ▫ towing this vehicle b...

  • Page 417

    Starting procedures before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your ve...

  • Page 418

    Caution! (continued) • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle speed. • do not shift from reverse, park, or neutral into any forward gear when the engine is above i...

  • Page 419

    Installing and removing the engine start/stop button installing the button 1. Remove the key fob from the ignition switch. 2. Insert the engine start/stop button into the ignition switch with the lettering facing up and readable. 3. Press firmly on the center of the button to secure it into position...

  • Page 420

    To turn off the engine using engine start/stop button 1. Place the shift lever in park, then press and release the engine start/stop button. 2. The ignition switch will return to the off position. 3. If the shift lever is not in park, the engine start/ stop button must be held for two seconds and ve...

  • Page 421

    • press the engine start/stop button a second time to change the ignition switch to the run position (evic displays “ignition mode run”), • press the engine start/stop button a third time to return the ignition switch to the off position (evic displays “ignition mode off”). Extreme cold weather (bel...

  • Page 422

    Clearing a flooded engine (using engine start/stop button) if the engine fails to start after you have followed the “normal starting” or “extreme cold weather ⬙ proce- dures, it may be flooded. To clear any excess fuel, press and hold the brake pedal, push the accelerator pedal all the way to the fl...

  • Page 423

    The engine block heater cord is located: • 3.6l engine – coiled and strapped to the engine oil dipstick tube. • 5.7l engine – bundled and fastened to the injector harness. The engine block heater must be plugged in at least one hour to have an adequate warming effect on the engine. Warning! Remember...

  • Page 424

    Warning! • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, and remove the key fob. Once the key f...

  • Page 425

    Warning! (continued) • children should be warned not to touch the park- ing brake, brake pedal or the shift lever. Do not leave the key fob in or near the vehicle, and do not leave keyless enter-n-go in the acc or on/run mode. A child could operate power windows, other controls, or move the vehicle....

  • Page 426

    Shifting from drive to park or reverse should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when moving the shift lever between these gears. The transmission shift lever has only park, reverse, neutral, and drive shift p...

  • Page 427

    Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use park while vehicle is in motion. Apply the parking brake when leaving vehicle in this range. When parking on a level surface, you may place the shift lever in the ...

  • Page 428

    Warning! (continued) • it is dangerous to move the shift lever out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone ...

  • Page 429

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. Do not leave the key fob in or near the ve...

  • Page 430

    • with brake pedal released, verify that the shift lever will not move out of park. Reverse this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral use this range when the vehicle is standing for prolonged periods with engine runn...

  • Page 431

    When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading condi- tions, in hilly terrain, traveling into strong head winds, or while towing heavy trailers), use the electronic range select (ers) feature (refer to “electronic range select (ers)” in this sectio...

  • Page 432

    Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required...

  • Page 433

    Note: to select the proper gear position for maximum deceleration (engine braking), simply press and hold the shift lever to the left (-). The transmission will shift to the range from which the vehicle can best be slowed down. Overdrive operation the automatic transmission includes an electronicall...

  • Page 434

    Right (-/+) while in the drive position will select the highest available transmission gear, and will display that gear in the instrument cluster as 6, 5, 4, 3, 2, 1. Gear ranges do not race the engine when shifting from park or neutral into another gear range. Park this range supplements the parkin...

  • Page 435

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to move...

  • Page 436

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, and remove the key fob. On...

  • Page 437

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 438

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 439

    These conditions, using a lower gear range will improve performance and extend transmission life by reducing excessive shifting and heat buildup. If the transmission operating temperature exceeds nor- mal operating limits, the powertrain controller will modify the transmission shift schedule and exp...

  • Page 440

    Transmission limp home mode transmission function is monitored electronically for abnormal conditions. If a condition is detected that could result in transmission damage, transmission limp home mode is activated. In this mode, the transmission remains in third gear regardless of which forward gear ...

  • Page 441

    The transmission into 3 (third gear), the transmission will never shift above third gear, but will shift down into second and first gear normally. Use of ers (or tow/haul mode) also enables an additional underdrive gear which is not normally used during through-gear accelerations. This additional ge...

  • Page 442

    Shift lever to the left (-). The transmission will shift to the range from which the vehicle can best be slowed down. Overdrive operation the automatic transmission includes an electronically controlled overdrive (fourth and fifth gears). The trans- mission will automatically shift into the overdriv...

  • Page 443

    The “tow/haul indicator light” will illuminate in the instrument cluster to indicate that tow/haul mode has been activated. Pressing the switch a second time restores normal operation. If the tow/haul mode is desired, the switch must be pressed each time the engine is started. Torque converter clutc...

  • Page 444

    Electronic range select (ers) feature, when the trans- mission is sufficiently warm, will demonstrate that the transmission is able to shift into and out of overdrive. • if the vehicle has not been driven for several days, the first few seconds of operation after shifting the trans- mission into gea...

  • Page 445

    When additional traction is required, the 4wd low position can be used to lock the front and rear driveshafts together and force the front and rear wheels to rotate at the same speed. The 4wd low position is intended for loose, slippery road surfaces only. Driving in the 4wd low position on dry, har...

  • Page 446

    Note: refer to “selec-terrain 威 – if equipped” in “start- ing and operating” for further information on the vari- ous positions and their intended usages. Neutral this range disengages both the front and rear driveshafts from the powertrain. It is to be used for flat towing behind another vehicle. R...

  • Page 447

    Note: if shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “for 4x4 low slow below 3 mph or 5 kph put trans in n press 4 low” message will flash from the electronic vehicle information center (evic). Refer to “electronic vehicle information ...

  • Page 448

    “electronic vehicle information center (evic)” in “understanding your instrument panel” for further information. • shifting into or out of 4wd low is possible with the vehicle completely stopped; however, difficulty may occur due to the mating clutch teeth not being prop- erly aligned. Several attem...

  • Page 449

    Note: if shift conditions/interlocks are not met, a “to tow vehicle safely, read neutral shift procedure in owners manual” message will flash from the electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)” in “understanding your instrument panel” for fu...

  • Page 450

    Selec-terrain™ — if equipped description selec-terrain™ combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance for all terrains. Selec-terrain™ consists of the following positions: • sport – dry weather, on-road calibration. Only avail- abl...

  • Page 451

    With air suspension, the level will change to normal ride height (nrh) if the transfer case is in high range. The level will change to off-road 1 if the transfer case is in low range. • auto – fully automatic full time four-wheel drive operation can be used on and off road. Balances traction with se...

  • Page 452

    Quadra-lift™ — if equipped description the quadra-lift™ air suspension system provides full time load leveling capability along with the benefit of being able to adjust vehicle height by the push of a button. Selec-terrain™ switch 1 — up button 2 — down button 3 — park mode indicator lamp 4 — normal...

  • Page 453

    • normal ride height (nrh) – this is the standard position of the suspension and is meant for normal driving. • off-road 1 (or1) (raises the vehicle approximately 1.3 in (33 mm) – this position should be the default position for all off-road driving until or2 is needed. A smoother and more comfortab...

  • Page 454

    Selec-terrain™ knob is turned to the “sport” posi- tion. Turning the selec-terrain™ knob to the “auto” position will return the system to normal operation. • park mode (lowers the vehicle approximately 1.5 in (38 mm) – this position lowers the vehicle for easier passenger entry and exit as well as l...

  • Page 455

    After the engine is turned off, it may be noticed that the air suspension system operates briefly, this is normal. The system is correcting the position of the vehicle to ensure a proper appearance. To assist with changing a spare tire, the quadra-lift™ air suspension system has a feature which allo...

  • Page 456

    Operation the indicator lamps 3 through 6 will illuminate to show the current position of the vehicle. Flashing indicator lamps will show a position which the system is working to achieve. When raising, if multiple indicator lamps are flashing on the “up” button, the highest flashing indica- tor lam...

  • Page 457

    • normal ride height (nrh) – indicator lamp 4 will be illuminated when the vehicle is in this position. • park mode – indicator lamp 3 will be illuminated when the vehicle is in park mode. If park mode is requested while vehicle speed is between 15 mph (24 km/h) and 25 mph (40 km/h), indicator lamp ...

  • Page 458

    Off-road driving tips note: prior to off-road driving, remove the front air dam to prevent damage. The front air dam is attached to the lower front fascia with seven quarter turn fasteners and can be removed by hand. Quadra-lift™ – if equipped when off-roading, it is recommended that the lowest usea...

  • Page 459

    Caution! Do not use 4wd low range when operating the vehicle on dry pavement. Driveline hardware dam- age can result. Driving through water although your vehicle is capable of driving through water, there are a number of precautions that must be considered before entering the water. Note: your vehic...

  • Page 460

    And/or the flow rate is reduced. If you must cross flowing water avoid depths in excess of 9 inches (23 cm). The flowing water can erode the streambed, causing your vehicle to sink into deeper water. Determine exit point(s) that are downstream of your entry point to allow for drifting. Standing wate...

  • Page 461

    If you stall or begin to lose forward motion while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brakes. Restart the engine, and shift into reverse. Back slowly down the hill, allowing the compression braking of the engine to help regulate your speed. If the b...

  • Page 462

    After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect...

  • Page 463

    • if you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material. Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation. Power steering 3.6l engine your vehicle is equipped with an electro-...

  • Page 464

    Occurred, which caused an over temperature condition in the power steering system. You will lose power steering assistance momentarily until the over temperature con- dition no longer exists. Once driving conditions are safe, then pull over and let vehicle idle for a few moments until the light turn...

  • Page 465

    System. This noise should be considered normal, and it does not in any way damage the steering system. Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the ...

  • Page 466

    If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Multi-displacement system (mds) (if equipped) — 5.7l engine only thi...

  • Page 467

    When the parking brake is applied with the ignition switch in the on position, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the transmis- sion is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, ...

  • Page 468

    Warning! (continued) • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others ...

  • Page 469

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes the anti-lock brake system (abs), traction control system (tcs), brake assist system (bas), electronic roll mitigation (erm), and electronic stability control (esc). All five of th...

  • Page 470

    Differential (bld), functions similar to a limited-slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel...

  • Page 471

    Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicle speed are sufficient to potentially cause wheel lift...

  • Page 472

    Electronic stability control (esc) this system enhances directional control and stability of the vehicle under various driving conditions. Esc cor- rects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteer or unders...

  • Page 473

    Warning! The electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent col- lisions, including those resulting from excessive speed in turns, driving on very ...

  • Page 474

    To be used if the vehicle is in deep snow, sand, or gravel conditions and more wheel spin than esc would nor- mally allow is required to gain traction. To turn esc on again, momentarily press the “esc off” switch. This will restore the normal “esc on” mode of operation. Note: to improve the vehicle’...

  • Page 475

    Trailer sway control (tsc) tsc uses sensors in the vehicle to recognize an exces- sively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appro- priate wheel(s) to counteract the sway of the trailer. Tsc ...

  • Page 476

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 6% (approximate) grade or greater hill. • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphi...

  • Page 477

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision w...

  • Page 478

    Ready alert braking – if equipped ready alert braking may reduce the time required to reach full braking during emergency braking situations. It anticipates when an emergency braking situation may occur by monitoring how fast the throttle is released by the driver. When the throttle is released very...

  • Page 479

    When hdc is enabled, the hdc icon will be illuminated in the instrument cluster. Hdc will automatically apply the brakes to control downhill speed to the selected level when necessary on grades greater than approximately 8%. It will usually not activate on level ground. The hdc speed may be adjusted...

  • Page 480

    4wd low range set speeds • 1st = 1 mph (1.6 km/h) • 2nd = 2.5 mph (4 km/h) • 3rd = 4 mph (6 km/h) • 4th = 5.5 mph (9 km/h) • 5th, 6th or d (drive) = 7.5 mph (12 km/h) • reverse = 1 mph (1.6 km/h) • neutral = 2.5 mph (4 km/h) • park = hdc will not function hdc is intended for low speed off-road drivi...

  • Page 481

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is turned to the on position. It should turn off with the engine running. If the “esc activation/malfunction indicat...

  • Page 482

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 483

    Compact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Ex- ample: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing chart...

  • Page 484

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 485

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 486

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 487

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Tire and loading information placard this placard tells you important information about the: ...

  • Page 488

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 489

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 490

    488 starting and operating.

  • Page 491

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 492

    Warning! (continued) • unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns...

  • Page 493

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage it. Inflation pressures specified on the placard are always cold tire inflation pressure. Cold tire inflation pressure...

  • Page 494

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 495

    Vehicle. If your vehicle has this option refer to an authorized tire dealer for the recommended tire rotation pattern. If your vehicle is not equipped with an original equip- ment tire and wheel as a spare, a non-matching tempo- rary emergency use spare may be equipped with your vehicle. Temporary u...

  • Page 496

    Warning! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnin...

  • Page 497

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressure listed on your tire and loading info...

  • Page 498

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 499

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place wit...

  • Page 500

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 501

    • due to limited clearance, use sae class “s” low profile cables or traction devices only. Security chain com- pany (scc) super z6 #sz 441 cables or equivalent are recommended. Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. ...

  • Page 502

    Caution! (continued) • observe the traction device manufacturer’s in- structions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufac- turer’s if it is less than 30 mph (48 km/h). • do not use traction devices on a com...

  • Page 503

    These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on on/off-road type tires. Rotation will increase tread life, help to main- tain mud, snow, and wet traction levels, and contribute to a smooth, qu...

  • Page 504

    The outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three-hour pe...

  • Page 505

    Light will still be on. In this situation, the tire pressure monitoring telltale light will turn off only after the tires have been inflated to the vehicle’s recommended cold tire pressure value. Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures have ...

  • Page 506

    • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure using an accurate tire gauge, even if under-inflation has not reached the level to trigger illumination of the tire pressure monitoring telltale light. • seasonal tem...

  • Page 507

    Will automatically update and the tire pressure monitor- ing telltale light will extinguish, once the updated tire pressures have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. The tire pressure monitoring telltale light will...

  • Page 508

    For 75 seconds and then remain on solid. In addition, a “service tpm system” message will be displayed for a minimum of five seconds. For each subsequent ignition switch cycle, a chime will sound, a “service tpm system” message will be displayed for a minimum of five seconds, and the tire pressure m...

  • Page 509

    • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illuminate in the instrument cluster, and an au- dible chime will be activated, when one or more of the four active road tire pressures are low. In addition, the ...

  • Page 510

    Once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. Service tpm system warning the tire pressure monitoring telltale light will flash on and off for 75 seconds, and remain on solid when a sys...

  • Page 511

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, the ⬙ service tpm system ⬙ message will not be present, and a pressure value will be displayed...

  • Page 512

    Tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. In addition, the evic will display a “service tpm system ⬙ mes- sage for five seconds and then display dashes (- -) in place of the pressure value. For each subsequent ignition switch cycle, a chim...

  • Page 513

    Fuel requirements 3.6l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high-quality unleaded “regular” gaso- line having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide a...

  • Page 514

    Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline.” reformulated gasoline contains oxygenates and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of ref...

  • Page 515

    If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: • operate in a lean mode • obd ii “malfunction indicator light” on • poor engine performance • poor cold start and cold driveability • increased risk for fuel system component corrosion t...

  • Page 516

    Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the f...

  • Page 517

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 518

    The other sections of this manual for information on features that are common between flexible fuel and gasoline-only powered vehicles. Caution! Only vehicles with the e-85 fuel filler door label can operate on e-85. E-85 fuel cap e-85 badge 516 starting and operating.

  • Page 519

    Ethanol fuel (e-85) e-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Warning! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap)...

  • Page 520

    • some additives used in regular gasoline are not fully compatible with e-85 and may form deposits in your engine. To eliminate driveability issues that may be caused by these deposits, a supplemental gasoline additive, such as mopar 威 injector cleanup or techron may be used. Selection of engine oil...

  • Page 521

    Replacement parts many components in your flexible fuel vehicle (ffv) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol com- patible parts. Caution! Replacing fuel system components with non-ethanol compatible components can damage your veh...

  • Page 522

    1. Press the fuel filler door release switch (located under the headlamp switch). 2. Open the fuel filler door, and remove the fuel filler cap. Fuel filler door release switch fuel filler cap 520 starting and operating.

  • Page 523

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indi- cator light (mil)” to illuminate, due to f...

  • Page 524

    • tighten the gas cap about one-quarter turn until you hear one click. This is an indication that the cap is properly tightened. • if the gas cap is not tighten properly, the mil will come on. Be sure the gas cap is tightened every time the vehicle is refueled. Emergency fuel filler door release if ...

  • Page 525

    In “understanding your instrument panel” for further information. Tighten the fuel filler cap properly and press the select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. Vehicle loading certification label as required by natio...

  • Page 526

    Springs, tires, or wheels). Heavier axles or suspension components, sometimes specified by purchasers for in- creased durability, does not necessarily increase the ve- hicle’s gvwr. Tire size the tire size on the label represents the actual tire size on your vehicle. Replacement tires must be equal ...

  • Page 527

    Until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving. Improper weight distributions can have an adverse affect on the way your vehicle steers and handles, and the way the brak...

  • Page 528

    Exceed the gvwr. Refer to “vehicle loading/vehicle certification label” in “starting and operating” for further information. Gross trailer weight (gtw) the gtw is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- porary) loaded in or on the trailer ...

  • Page 529

    Gross axle weight rating (gawr) the gawr is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear gawr. Refer to “vehicle loading/vehicle certifica- tion label” in “starting and operating” for...

  • Page 530

    Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kind of hitches are the most popular on the market today and they are commonly used to tow small- and medium- size...

  • Page 531

    Warning! • an improperly adjusted weight-distributing hitch system may reduce handling, stability, and brak- ing performance, and could result in a collision. • weight-distributing hitch systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a re...

  • Page 532

    With weight-distributing hitch (correct) improper adjustment of weight-distributing hitch (incorrect) 530 starting and operating.

  • Page 533

    Trailer hitch classification your vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional trailer tow prep package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weig...

  • Page 534

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/model model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l 4x2 10,40...

  • Page 535

    Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels, or heavier in the rear, can cause the trailer to sway severely side-to...

  • Page 536

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to “tire safety information/tire and loading information...

  • Page 537

    Warning! (continued) • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision. •...

  • Page 538

    Towing requirements – tires − do not attempt to tow a trailer while using a compact spare tire. − proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation proce...

  • Page 539

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 540

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 541

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic transmission the drive range can be selected when towing. How- ever, if frequent shifting occurs while in this range, the tow/haul mode (if equipped), or a lower...

  • Page 542

    Cooling system to reduce potential for engine and transmission over- heating, take the following actions: − city driving when stopped for short periods of time, shift the trans- mission into neutral and increase engine idle speed. − highway driving reduce speed. − air conditioning turn off temporari...

  • Page 543

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheel off the ground two-wheel drive models four-wheel drive models flat tow none not allowed see instructions • transmission in park • transfer case in neutral (n) • tow in forward direction dol...

  • Page 544

    Recreational towing – two-wheel drive models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is allowed only if the rear wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly...

  • Page 545

    Caution! Towing this vehicle in violation of the above require- ments can cause severe transmission and/or transfer case damage. Damage from improper towing is not covered under the new vehicle limited warranty. Recreational towing – quadra–trac ii 姞 /quadra–drive 姞 ii four-wheel drive models the tr...

  • Page 546

    Caution! (continued) • failure to follow these procedures can cause se- vere transmission and/or transfer case damage. Damage from improper towing is not covered under the new vehicle limited warranty. • do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damage...

  • Page 547

    Caution! It is necessary to follow these steps to be certain that the transfer case is fully in neutral (n) before recreational towing to prevent damage to internal parts. 1. Bring the vehicle to a complete stop and shift the transmission to park. 2. Turn off the engine. 3. For vehicles with keyless...

  • Page 548

    7. Using the point of a ballpoint pen or similar object, press and hold the recessed transfer case neutral (n) button (located by the selector switch) for four seconds, until the light behind the n symbol starts to blink, indicating shift in progress. The light will stop blinking (stay on solid) whe...

  • Page 549

    Caution! Damage to the transmission may occur if the trans- mission is shifted into park with the transfer case in neutral (n) and the engine running. With the transfer case in neutral (n) ensure that the engine is off prior to shifting the transmission into park. 15. Attach the vehicle to the tow v...

  • Page 550

    Shifting out of neutral (n) use the following procedure to prepare your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply the parking brake. 3. Turn the ignition switch to the on/run position, but do not start the engine. 4....

  • Page 551

    8. After the neutral (n) button has been released, the transfer case will shift to the position indicated by the selector switch. 9. Shift the transmission into park. 10. Release the brake pedal. 11. Disconnect vehicle from the tow vehicle. 12. Start the engine. 13. Press and hold the brake pedal. 1...

  • Page 553: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . 552 䡵 if your engine overheats . . . . . . . . . . . . . . . . 552 䡵 jacking and tire changing . . . . . . . . . . . . . . . 553 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 554 ▫ spare tire...

  • Page 554

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank just above the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. ...

  • Page 555

    • you can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. Caution! Driving with a hot cooling system could damage ...

  • Page 556

    Warning! (continued) • being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be ra...

  • Page 557

    Spare tire stowage the spare tire is stowed under the load floor in the rear cargo area and is secured to the body with a special wing nut. Preparations for jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery surfaces. Warning! Do not attempt to change a tire on the side of t...

  • Page 558

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the ...

  • Page 559

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare tire, jack, and tools from storage. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left, one turn, while the whee...

  • Page 560

    Caution! Do not attempt to raise vehicle by jacking on loca- tions other than those indicated in the jacking in- structions for this vehicle. 4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do n...

  • Page 561

    5. For a rear tire, place the jack in the slot on the rear tie-down bracket, just forward of the rear tire (as indi- cated by the triangular lift point symbol on the sill molding). Do not raise the vehicle until you are sure the jack is fully engaged. Front jacking location lift point symbol on sill...

  • Page 562

    6. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. Warning! Raising the vehicle higher than necessary can make the vehicle le...

  • Page 563

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 9. Lower the vehicle by turning the jack screw counter- clockwise, and remove the jack and wheel block...

  • Page 564

    12. Remove the small center cap and securely store the road wheel in the cargo area. 13. Have the aluminum road wheel and tire repaired as soon as possible, properly secure the spare tire with the special wing nut torqued to 3.7 ft-lbs (5 n·m), reinstall the jack and tool kit foam tray, and latch th...

  • Page 565

    Road tire installation 1. Mount the road tire on the axle. 2. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has b...

  • Page 566

    Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electrical system may occur. Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode ...

  • Page 567

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

  • Page 568

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) j...

  • Page 569

    8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the remote positive (+) post of the discharged vehicle. 10. Reinstall the protective cover over the remote posi- tive (+) bat...

  • Page 570

    Caution! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the en- gine to idle with the shift lever in neutral for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure du...

  • Page 571

    Emergency tow hooks — if equipped if your vehicle is equipped with tow hooks, there will be one in the rear and two mounted on the front of the vehicle. The rear hook will be located on the driver’s side of the vehicle. Note: for off-road recovery, it is recommended to use both of the front tow hook...

  • Page 572

    4. Using a screwdriver or similar tool, carefully remove the shift lever override access cover, located on the bottom of the cupholder. 5. Press and maintain firm pressure on the brake pedal. 6. Using the screwdriver or similar tool, press and hold the shift lock lever down. 7. Move the shift lever ...

  • Page 573

    Note: vehicles equipped with quadra-lift™ must be lowered to the park (lowest) level, and have automatic leveling disabled, before tying them down (from the body) on a trailer or flatbed truck. Refer to the section on quadra-lift™ for more information. If the vehicle cannot be lowered to the park le...

  • Page 574

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members o...

  • Page 575

    Two-wheel drive models the manufacturer recommends towing your vehicle with all four wheels off the ground using a flatbed. If flatbed equipment is not available, and the transmis- sion is operable, the vehicle may be towed (with rear wheels on the ground) with the transmission in neu- tral . Speed ...

  • Page 576

    Four-wheel drive models the manufacturer recommends towing with all wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of vehicle raised and the opposite end on a towing dolly. If flatbed equipment is not available, and the transfer case is operable, vehicl...

  • Page 577: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . . . . . 577 䡵 engine compartment — 5.7l . . . . . . . . . . . . . 578 䡵 onboard diagnostic system – obd ii . . . . . . . 579 ▫ loose fuel filler cap message . . . . . . . . . . . 579 䡵 emissions inspection and maintenanc...

  • Page 578

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 603 ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . 605 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . 606 ▫ automatic transmission . . . . . . . . . . . . . . . 607 ▫ appearance care and protection from corrosion ...

  • Page 579

    Engine compartment — 3.6l 1 — totally integrated power module (fuses) 6 — air cleaner filter 2 — engine oil dipstick 7 — washer fluid reservoir 3 — engine oil fill 8 — coolant pressure cap (radiator) 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — power steering fluid reservoir 7 maintain...

  • Page 580

    Engine compartment — 5.7l 1 — totally integrated power module (fuses) 6 — washer fluid reservoir 2 — automatic transmission dipstick 7 — engine oil dipstick 3 — engine oil fill 8 — coolant pressure cap (radiator) 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — air cleaner filter 578 maint...

  • Page 581

    Onboard diagnostic system – obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 582

    The select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the malfunction indicator light (mil). Emissions inspection and maintenance programs in some l...

  • Page 583

    4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 584

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 585

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 586

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to “maintenance schedule” for further information. Note: under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or six months, whichev...

  • Page 587

    Engine oil viscosity – 3.6l engine sae 5w-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil...

  • Page 588

    Materials added to engine oils do not add any supplemental materials, other than leak detection dyes, to your engine oil. Engine oil is an engineered product and its performance may be im- paired by supplemental additives. Disposing of used engine oil and oil filters care should be taken in disposin...

  • Page 589

    Warning! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compa...

  • Page 590

    Warning! (continued) • battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories...

  • Page 591

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt condition should also be checked at t...

  • Page 592

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency (epa) and is an ozone-saving product. However, the manufacturer recommends that air condi- tioning service be performed by authorized dealers ...

  • Page 593

    5. Remove the a/c air filter by pulling it straight out of the housing. 6. Install the a/c air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. Caution! The a/c air filter is identified with an arrow...

  • Page 594

    Hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of...

  • Page 595

    Note: the rear wiper arm cannot be raised fully upward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. 1 ...

  • Page 596

    4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade and snap the pivot cap into place. Adding washer fluid on vehicles equipped with a electronic vehicle informa- tion cente...

  • Page 597

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 598

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions con- trol device and may seriously reduce engine per- formance and cause serious damage to the engine. • damage to the catalytic converter can r...

  • Page 599

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 600

    Accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Insp...

  • Page 601

    Caution! • mixing of engine coolant (antifreeze), other than the specified hoat engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. If a non-hoat engine cool- ant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced wit...

  • Page 602

    • mix a minimum solution of 50% hoat engine coolant (antifreeze) and distilled water. Use higher concentra- tions (not to exceed 70%) if temperatures below -34°f (-37°c) are anticipated. • use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifre...

  • Page 603

    Warning! • the warning words do not open hot on the cooling system pressure cap are a safety precau- tion. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To pre...

  • Page 604

    Of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the...

  • Page 605

    • keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in uns...

  • Page 606

    With disc brakes, the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in fluid level may be caused by a leak and a system check should be conducted. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Warn...

  • Page 607

    Warning! (continued) • do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Front/rear axle fluid for normal service, periodic fluid level checks are not required. Whe...

  • Page 608

    Caution! Do not over tighten the plugs as it could damage then and cause them to leak. Selection of lubricant use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintain- ing your vehicle” for further information. Transfer case fluid level check inspe...

  • Page 609

    Automatic transmission selection of lubricant it is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only the manufacturer’s recommended trans- mission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicl...

  • Page 610

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check – 3.6l engine regular fluid level checks are not required. For this reason, the dipstick is omitted....

  • Page 611

    Fluid level check – 5.7l engine check the fluid level while the transmission is at normal operating temperature. This occurs after at least 15 miles (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably between the fingertips. To check the fluid level properly, the...

  • Page 612

    Caution! Be aware that if the fluid temperature is below 50°f (10°c) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission afte...

  • Page 613

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar 威 car wash or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar 威 super kleen bug and tar remove...

  • Page 614

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause which destroys the paint and protective coating, have your vehicle repaired a...

  • Page 615

    Stain repel fabric cleaning procedure – if equipped stain repel seats may be cleaned in the following man- ner: • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar 威 total clean or a mild ...

  • Page 616

    Taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather condi- tioner is not required to maintain the original condition. Warning! Do ...

  • Page 617

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol con...

  • Page 618

    Fuses totally integrated power module the totally integrated power module is located in the engine compartment. This center contains cartridge fuses and mini fuses. A description of each fuse and compo- nent may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on t...

  • Page 619

    Cavity cartridge fuse mini fuse description j03 30 amp pink trailer tow j04 25 amp natural driver door node j05 25 amp natural passenger door node j06 40 amp green antilock brakes pump/stability control system j07 30 amp pink antilock brakes valve/stability control system j08 40 amp green power seat...

  • Page 620

    Cavity cartridge fuse mini fuse description j18 20 amp blue powertrain control module/powertrain control module transmission range j19 60 amp yellow radiator fan motor hi/radiator fan motor low j20 30 amp pink front wiper j21 20 amp blue front/rear washer control j22 25 amp natural sunroof module m1...

  • Page 621

    Cavity cartridge fuse mini fuse description m11 10 amp red heating, ventilation & air conditioning (cli- mate control system) m12 30 amp green radio/amplifier m13 20 amp yellow instrument cluster m14 20 amp yellow back up camera – if equipped m15 20 amp yellow power seat module(s)/adaptive cruise co...

  • Page 622

    Cavity cartridge fuse mini fuse description m25 20 amp yellow fuel pump motor output/diesel lift pump (export only) m26 10 amp red driver door switch bank m27 10 amp red ignition switch/ wireless control module/keyless entry module m28 15 amp blue powertrain controller/ transmission controller m29 1...

  • Page 623

    Cavity cartridge fuse mini fuse description m37 10 amp red antilock brakes/ stability control system module m38 25 amp natural all door lock &unlock caution! • when installing the totally integrated power mod- ule cover, it is important to ensure the cover is properly positioned and fully latched. F...

  • Page 624

    • anytime you store your vehicle, or keep it out of service (i.E. Vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage wh...

  • Page 625

    Bulb replacement high intensity discharge headlamps (hid) – if equipped the headlamps are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlamp switch off and the key removed. Because of this, you should not attempt to service a headlamp bulb yourself. ...

  • Page 626

    Front turn signal 1. Open the hood. 2. Turn the turn signal bulb one–quarter turn counter- clockwise to remove from housing. 3. Disconnect the electrical connector and replace the bulb. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bu...

  • Page 627

    4. Align the index tabs of the front fog lamp bulb with the slots in the collar of the bulb opening on the back of the front fog lamp housing. 5. Insert the bulb into the housing until the index tabs are engaged in the slots of the collar. 6. Firmly and evenly push the bulb straight into the lamp ho...

  • Page 628

    6. Replace the bulb, reinstall the socket, and reattach the lamp assembly. Rear liftgate mounted tail lamp 1. Raise the liftgate. 2. Use a fiber stick or flat blade screw driver to pry the lower trim from the liftgate. 3. Once lower trim is loose, close the liftgate. 4. Open the flipper glass. 5. Pu...

  • Page 629

    Center high-mounted stop lamp (chmsl) the center high-mounted stop lamp is an led assembly. See your authorized dealer for replacement. Rear license lamp 1. Use a screw driver to gently pry against the side of the snap tab to remove the license lamp lens. 2. Pull bulb from socket. 3. Replace bulb. 4...

  • Page 630

    Fluid capacities u.S. Metric fuel (approximate) all engines 24.6 gallons 93 liters engine oil with filter 3.6l engine (sae 5w-30, api certified) 6 quarts 5.6 liters 5.7l engine (sae 5w-20, api certified) 7 quarts 6.6 liters cooling system * 3.6l engine (mopar 威 engine coolant/antifreeze 5-year/100,0...

  • Page 631

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hy- brid organic additive technology) or equivalent. Engine oil – 3.6l engine use api certified sae 5w-30 engine oil, meeting the requi...

  • Page 632

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 威 automatic transmission fluid or equivalent li- censed atf+4 威 product. Transfer case – 3.6l engine shell automatic transmission fluid 3353 or equivalent. Transfer case – 5.7l engine mopar 威 atf+4 威 automatic t...

  • Page 633

    Component fluid, lubricant, or genuine part power steering reservoir – 3.6l engine mopar 威 hydraulic fluid or equivalent meeting ms-11655, such as fuchs eg zh 3044 or pentosin chf 11s. Power steering reservoir – 5.7l engine mopar 威 power steering fluid +4, mopar 威 atf+4 威 automatic transmission flui...

  • Page 635: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 634 ▫ required maintenance intervals . . . . . . . . . . 636 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 636

    Maintenance schedule the scheduled maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating condition...

  • Page 637

    Note: • the oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is not illuminated. • change your engine oil more often if you drive your vehicle off...

  • Page 638

    Once a month • check tire pressure and look for unusual wear or damage. • check the fluid levels of the coolant reservoir, brake master cylinder, power steering and transmission (5.7l only) and add as needed. • check all lights and other electrical items for correct operation. At each oil change • c...

  • Page 639

    8,000 miles (13,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). Odometer reading date repair order # dealer code signature, authorized ser...

  • Page 640

    24,000 miles (39,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 24,000 miles (39 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. ❏ inspect the front ...

  • Page 641

    40,000 miles (65,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). Odometer reading date repair order # dealer code signature, authorized ...

  • Page 642

    56,000 miles (91,000 km) or 42 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km). Odometer reading date repair order # dealer code signature, authorized ...

  • Page 643

    64,000 miles (104,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). ❏ replace the engine air cleaner filter. ❏ replace the air conditioni...

  • Page 644

    72,000 miles (117,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. ❏ inspect the fron...

  • Page 645

    88,000 miles (143,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). Odometer reading date repair order # dealer code signature, authorize...

  • Page 646

    96,000 miles (156,000 km) or 72 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏ replace the engine air cleaner filter. ❏ replace the air conditioni...

  • Page 647

    104,000 miles (169,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ flush and replace the engine coolant at 104,000 miles (169 000 km...

  • Page 648

    120,000 miles (195,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. ❏ inspect the fr...

  • Page 649

    128,000 miles (208,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). ❏ replace the engine air cleaner filter. ❏ replace the air conditio...

  • Page 650

    144,000 miles (234,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 144,000 miles (234 000 km). ❏ if using your vehicle for any of the following: dusty or off-roa...

  • Page 651

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • failure to properly inspect and mai...

  • Page 653: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653 ▫ prepare for the appointment . . . . . . . . . . . 653 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 653 ▫ be reasonable with r...

  • Page 654

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 659 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 659 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 659 ▫ temperature grades . . . . . . . . . . . . . . . . . . 66...

  • Page 655

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 656

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 657

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 658

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 659

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 660

    • service manuals these comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group llc vehicles. A complete working knowledge of the vehicle, system, and/or...

  • Page 661

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 662

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 663: Index

    Index 10

  • Page 664

    Adaptive cruise control (acc) (cruise control) . . 200 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 519 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . 514 air cleaner, engine (engine air cleaner filter) . . . 586 air conditioner maintenance . . . . . . . . . ....

  • Page 665

    Fluid and filter changes . . . . . . . . . . . . . . . 607 fluid level check . . . . . . . . . . . . . . . . . 608,609 fluid type . . . . . . . . . . . . . . . . . . . . . . . . . 607 special additives . . . . . . . . . . . . . . . . . . . . . 607 autostick . . . . . . . . . . . . . . . . . . . . . ...

  • Page 666

    Cargo area cover . . . . . . . . . . . . . . . . . . . . . . . 271 cargo area features . . . . . . . . . . . . . . . . . . . . . . 269 cargo compartment . . . . . . . . . . . . . . . . . . . . . . 269 light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 cargo light . . . . . . . . . ....

  • Page 667

    Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . 597 adding coolant (antifreeze) . . . . . . . . . . . . . 599 coolant capacity . . . . . . . . . . . . . . . . . . . . . 628 coolant level . . . . . . . . . . . . . . . . . . . . . . . 601 disposal of used coolant . . . . . . . . . . ....

  • Page 668

    E-85 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515 electric remote mirrors . . . . . . . . . . . . . . . . . . . 109 electrical outlet, auxiliary (power outlet) . . . . . . 258 electronic brake control system . . . . . . . . . . . . . 467 anti-lock brake system . . . . . . . . ....

  • Page 669

    Oil selection . . . . . . . . . . . . . . . . . . . . . 584,628 oil synthetic . . . . . . . . . . . . . . . . . . . . . . . . 585 overheating . . . . . . . . . . . . . . . . . . . . . . . . 552 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 temperature gauge . . . . . . . . . . ....

  • Page 670

    Fluid leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 fluid level checks automatic transmission . . . . . . . . . . 607,608,609 brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 603 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . 583 power steering . . ....

  • Page 671

    Garage door opener (homelink®) . . . . . . . . . . . 242 gas cap (fuel filler cap) . . . . . . . . . . . . 519,522,579 gasoline (fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 511 conserving . . . . . . . . . . . . . . . . . . . . . . . . . 311 gasoline, clean air . . . . . . . . . . . . . ...

  • Page 672

    Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14,16 ignition key removal . . . . . . . . . . . . . . . . . . . . . 16 illuminated entry . . . . . . . . . . . . . . . . . . . . . . . . 23 immobilizer (sentry key...

  • Page 673

    Leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496 liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 liftgate flipper glass . . . . . . . . . . . . . . . . . . . . . . 45 liftgate...

  • Page 674

    Service engine soon (malfunction indicator) . . . . . . . . . . . . . . . . 285 side marker . . . . . . . . . . . . . . . . . . . . . . . . 625 smartbeams . . . . . . . . . . . . . . . . . . . . . . . . 182 tire pressure monitoring (tpms) . . . . . . . . . 288 tow/haul indicator . . . . . . . . . . ...

  • Page 675

    Mode fuel saver . . . . . . . . . . . . . . . . . . . . . . . . . . 311 modifications/alterations, vehicle . . . . . . . . . . . . . 9 monitor, tire pressure system . . . . . . . . . . . . . . . 501 mopar parts . . . . . . . . . . . . . . . . . . . . . . . . . 581,656 mtbe/etbe . . . . . . . . . . ....

  • Page 676

    Overheating, engine . . . . . . . . . . . . . . . . . . . 294,552 owner’s manual (operator manual) . . . . . . . . . 6,657 paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610 paint damage . . . . . . . . . . . . . . . . . . . . . . . . . . 610 panic alarm . . . . . . . . . . . ....

  • Page 677

    Radial ply tires . . . . . . . . . . . . . . . . . . . . . . . . . 492 radio operation . . . . . . . . . . . . . . . . . . . . . . . . 395 rain sensitive wiper system . . . . . . . . . . . . . . . . 192 rear axle (differential) . . . . . . . . . . . . . . . . . . . . 605 rear camera . . . . . . . . ...

  • Page 678

    Safety checks inside vehicle . . . . . . . . . . . . . . . . . 96 safety checks outside vehicle . . . . . . . . . . . . . . . 98 safety defects, reporting . . . . . . . . . . . . . . . . . . 656 safety information, tire . . . . . . . . . . . . . . . . . . . 480 safety tips . . . . . . . . . . . . . ...

  • Page 679

    Service engine soon light (malfunction indicator) . . . . . . . . . . . . . . . . . . . . 285 service manuals . . . . . . . . . . . . . . . . . . . . . . . . 657 setting the clock . . . . . . . . . . . . . . . . . . . . . 330,339 settings, personal . . . . . . . . . . . . . . . . . . . . . . . . 319...

  • Page 680

    Steering wheel mounted sound system controls . . . . . . . . . . . . . . . . . . . . . . . . . 393 storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 621 storage, vehicle . . . . . . . . . . . . . . . . . . . . . . 407,621 storing your vehicle . . . . . . . . . . . . . . . . . . ....

  • Page 681

    Pressure warning light . . . . . . . . . . . . . . . . 288 quality grading . . . . . . . . . . . . . . . . . . . . . 659 radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492 replacement . . . . . . . . . . . . . . . . . . . . . . . . 497 rotation . . . . . . . . . . . . . . . . . . . ....

  • Page 682

    Transmitter battery service (remote keyless entry) . . . . . . . . . . . . . . . . . . . . 27 transmitter programming (remote keyless entry) . . . . . . . . . . . . . . . . . . . . 24 transmitter, garage door opener (homelink®) . . 242 transmitter, remote keyless entry (rke) . . . . . . . . 24 tread...

  • Page 683

    Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 windshield defroster . . . . . . . . . . . . . . . . . . . 96,398 windshield washers . . . . . . . . . . . . . . . . . . . . . . 189 fluid . . . . . . . . . . . ....

  • Page 684

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 685

    Chrysler group llc 12wk741-126-ae -r1 5th edition printed in u.S.A..