1. DL manuals
  2. Jeep
  3. Automobile
  4. Grand Cherokee SRT 2014
  5. Owner's Manual

Jeep Grand Cherokee SRT 2014 Owner's Manual

Summary of Grand Cherokee SRT 2014

  • Page 1

    Cherokee chrysler group llc o w n e r ’ s m a n u a l 2014 cherokee 14kl74-126-aa first edition printed in u.S.A. 2 0 1 4.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million a...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against oper- ating procedures that could result in a collision or bodily injury. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss important ...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ ignition node module (ignm) — if equipped. .12 ▫ keyless ignition node (kin) . . . . . . . . . . . . . .13 ▫ key fob — if equipped . . . . . . . . . . . . . . . . . .14 ▫ ignition or accessory...

  • Page 12

    ▫ transmitter battery replacement . . . . . . . . . . .26 ▫ general information . . . . . . . . . . . . . . . . . . . .29 䡵 remote starting system — if equipped . .29 ▫ how to use remote start . . . . . . . . . . . . . . . .30 䡵 door locks . . . . . . . . . . . . . . . . . . . . . . . . .34 ▫ manual...

  • Page 13

    ▫ supplemental restraint system (srs) — air bags . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ advanced front air bag features . . . . . . . . . . .70 ▫ air bag deployment sensors and controls . . . .74 ▫ event data recorder (edr) . . . . . . . . . . . . . . .91 ▫ child restraints . . ...

  • Page 14

    A word about your keys your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a either a bladed key with an immobilizer chip in it, or a key fob with remote keyless entry (rke) transmitter and an ignition node module (ignm). The key...

  • Page 15

    Keyless ignition node (kin) this feature allows the driver to operate the ignition switch with the push of a button, as long as the remote keyless entry (rke) transmitter is in the passenger compartment. The keyless ignition node (kin) has four operating positions, three of which are labeled and wil...

  • Page 16

    Key fob — if equipped the key fob also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the key fob go dead. You can keep the emergency key with ...

  • Page 17

    Note: you can insert the double-sided emergency key into the lock cylinders with either side up. Emergency key removal (ignm) emergency key removal (kin) 2 things to know before starting your vehicle 15.

  • Page 18

    Ignition or accessory on message opening the driver’s door when the ignition is in acc or on (engine not running), a chime will sound to remind you to place the ignition in the off position. In addition to the chime, the ignition or accessory on message will display in the cluster. Note: with the uc...

  • Page 19

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. S...

  • Page 20

    Caution! The sentry key® immobilizer system is not compat- ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the key fobs provided with your new vehicle have been programmed to the vehicle electron...

  • Page 21

    Note: when having the sentry key® immobilizer sys- tem serviced, bring all vehicle keys with you to an authorized dealer. Customer key programming programming key fobs or rke transmitters may be performed at an authorized dealer. General information the sentry key® system complies with fcc rules par...

  • Page 22

    To arm the system follow these steps to arm the vehicle security alarm: 1. Remove the key from the ignition system (refer to ⬙ starting procedures ⬙ in ⬙ starting and operating ⬙ for further information). • for vehicles equipped with keyless enter-n-go™, make sure the vehicle ignition system is ⬙ of...

  • Page 23

    • cycle the vehicle ignition system out of the off position. • for vehicles equipped with keyless enter-n-go™ , press the keyless enter-n-go™ start/stop button (requires at least one valid key fob in the vehicle). • for vehicles not equipped with keyless enter-n-go™ , insert a valid key into the ign...

  • Page 24

    Security system manual override the vehicle security alarm will not arm if you lock the doors using the manual door lock plunger. Illuminated entry the courtesy lights will turn on when you use the remote keyless entry (rke) transmitter to unlock the doors or open any door. This feature also turns o...

  • Page 25

    Note: driving at speeds 5 mph (8 km/h) and above disables the system from responding to all rke transmit- ter buttons for all rke transmitters. Emergency key removal (kin) emergency key removal (ignm) 2 things to know before starting your vehicle 23.

  • Page 26

    To unlock the doors and liftgate press and release the unlock button on the rke transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn ...

  • Page 27

    To lock the doors and liftgate press and release the lock button on the rke transmit- ter to lock all doors and liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. If the vehicle is equipped with passive entry, refer to “keyless enter-n-go™” under “things t...

  • Page 28

    Programming additional transmitters programming key fobs or rke transmitters may be performed at an authorized dealer. Transmitter battery replacement the recommended replacement battery is one cr2032 battery. Note: • perchlorate material — special handling may apply. See www.Dtsc.Ca.Gov/hazardouswa...

  • Page 29

    2. Separating rke halves requires screw removal and gently prying the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. Emergency key removal (kin) remove screw from transmitter case 2 things to know before starting your vehicle 27.

  • Page 30

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the b...

  • Page 31

    New battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4. To assemble the rke transmitter case, snap the two halves together. General information this device complies with part 15 of the fcc rules and rss 210 of industry canad...

  • Page 32

    Note: • the vehicle must be equipped with an automatic transmission to be equipped with remote start. • obstructions between the vehicle and rke transmitter may reduce this range. How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever i...

  • Page 33

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Carbon monoxide is poisonous and can cause serious in- jury or death when inhaled. • keep remote keyless entry (rke) transmitters away from child...

  • Page 34

    To enter remote start mode press and release the remote start button on the rke transmitter twice within five seconds. The vehicle doors will lock, the parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the remote start...

  • Page 35

    To exit remote start mode and drive the vehicle before the end of 15 minute cycle, press and release the unlock button on the rke transmitter to unlock the doors and disarm the vehicle security alarm (if equipped). Then, prior to the end of the 15 minute cycle, press and release the start/stop butto...

  • Page 36

    Door locks manual door locks to lock each door, rotate the door lock knob on each door trim panel forward. To unlock the front doors, pull the inside door handle to the first detent or rotate the door lock button until the red indicator is visible. To unlock the rear doors, rotate the door lock butt...

  • Page 37

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n-go™ in the acc or on/run mode. A child could operate power windows, other controls, or move the vehicle. Power doo...

  • Page 38

    If you press the power door lock switch while the ignition is in the acc or on/run position, and any front door is open, the power locks will not operate. This prevents you from accidentally locking the key fob in the vehicle. Place the ignition to the off position or closing the door will allow the...

  • Page 39

    Child-protection door lock system — rear doors to provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a child-protection door lock system. To use the system, open each rear door, use a flat blade screwdriver (or ignition key) and rotate the dial ...

  • Page 40

    Note: • when the child lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. • after disengaging the child-protection door lock system, always test the door from the inside to make certain it is in the desir...

  • Page 41

    Note: • passive entry may be programmed on/off; refer to “uconnect® settings” in “understanding your instru- ment panel” for further information. • if wearing gloves on your hands, or if it has been raining on the passive entry door handle, the unlock sensitivity can be affected, resulting in a slow...

  • Page 42

    To unlock from the passenger side with a valid passive entry rke transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors and the liftgate automatically. Note: all doors will unlock when the front passenger door handle is grabbed reg...

  • Page 43

    Note: the vehicle will only unlock the doors when a valid passive entry rke transmitter is detected inside the vehicle, and no valid passive entry rke transmitter is detected outside the vehicle. The vehicle will not unlock the doors when any of the following conditions are true: • the doors are man...

  • Page 44

    Note: if “unlock all doors 1st press” is programmed in evic, all doors will unlock when you push the electronic liftgate release. If ⬙ unlock driver door 1st press ⬙ is programmed in uconnect®, only the liftgate will unlock when you press the electronic liftgate release. For further information, ref...

  • Page 45

    Note: • after pressing the door handle lock button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • the pas...

  • Page 46

    Windows power windows the window controls on the driver’s door control all the door windows. There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate only when the ignition is in the acc or on/run position. Note: f...

  • Page 47

    Warning! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, and do not leave the ignition of a vehicle equipped with keyless enter-n-go™ in the acc or on/run mode. Occu- pants, particularly unattended childr...

  • Page 48

    Note: • if the window runs into any obstacle during auto- closure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window. • any impact due to rough road conditions may trigger the auto-reverse function unexpectedly during auto- closu...

  • Page 49

    Window lockout switch the window lockout switch on the driver’s door trim panel allows you to disable the window controls on the rear passenger doors. To disable the window controls, press and release the window lockout button (setting it in the down position). To enable the window controls, press a...

  • Page 50

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof or sky slider™ (if equipped) in certain open or partially open positions. This is a normal oc...

  • Page 51

    Note: use the power door lock switch on either front door trim panel or the remote keyless entry (rke) transmitter to lock and unlock the liftgate. The manual door locks on the doors and the driver’s door lock cylinder will not lock and unlock the liftgate. Warning! Driving with the liftgate open ca...

  • Page 52

    The power liftgate may also be opened or closed by pressing the liftgate button located on the front overhead console, or closed by pressing the liftgate button located on left rear trim panel, near the liftgate opening. Pressing the liftgate button located on left rear trim panel once will close th...

  • Page 53

    Note: • the power liftgate buttons will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). • the power liftgate will not operate in temperatures below −22°f (−30°c) or temperatures above 150°f (65°c). Be sure to remove any buildup of snow or ice from the liftgate bef...

  • Page 54

    • if your liftgate is power closing and you put the vehicle in gear, the liftgate will continue to power close. However, vehicle movement may result in a detection of an obstruction. Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passenger...

  • Page 55

    • front seat belts incorporate pretensioners that may enhance occupant protection by managing occupant energy during an impact event • all seat belt systems (except the driver’s) include automatic locking retractors (alrs), which lock the seat belt webbing into position by extending the belt all the...

  • Page 56

    Warning! • never place a rear facing infant seat in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. • only use a rearward-facing child restraint in a vehicle with a...

  • Page 57

    5. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer center. Phone numbers are provided under ⴖ if you need assistance ⴖ . Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work wit...

  • Page 58

    Warning! (continued) • in a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up...

  • Page 59

    Warning! • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much wo...

  • Page 60

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” pulling out the lap/shoulder belt latch plate inserting latch plate into buckle 58 things to know before starting your vehicle.

  • Page 61

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden st...

  • Page 62

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collisio...

  • Page 63

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed posi- tion. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protec...

  • Page 64

    As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you will prefer a higher position. Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as po...

  • Page 65

    Seat belts in passenger seating positions the seat belts in the passenger seating positions are equipped with automatic locking retractors (alr) which are used to secure a child restraint system. For additional information, refer to “installing child re- straints using the vehicle seat belt” under t...

  • Page 66

    Position that has a belt with this feature. Children 12 years old and under should always be properly re- strained in a vehicle with a rear seat. How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire...

  • Page 67

    Energy management feature this vehicle has a safety belt system with an energy management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on collision. This safety belt system has a retractor assembly that is designed to release webbing in a co...

  • Page 68

    Passenger is unbelted, the seat belt reminder light will turn on and remain on until both front seat belts are fastened. The beltalert® warning sequence begins after the vehicle speed is over 5 mph (8 km/h), by blinking the seat belt reminder light and sounding an intermittent chime. Once the sequen...

  • Page 69

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt lo...

  • Page 70

    Panel below the steering column and a supplemental passenger side knee air bag mounted in the instrument panel below the glove compartment. Note: the driver and front passenger advanced front air bags are certified to the new federal regulations for advanced air bags. The advanced front air bags hav...

  • Page 71

    And rear passengers sitting next to a window. The sabic air bags, are located above the side windows and their covers are also labeled: srs airbag. This vehicle is equipped with supplemental seat- mounted side air bags (sab) to provide enhanced protection for an occupant during a side impact. The su...

  • Page 72

    • supplemental passenger side knee air bag • front and side impact sensors • front seat belt pretensioners, seat belt buckle switch, and seat track position sensors • occupant classification system (ocs) advanced front air bag features the advanced front air bag system has multistage driver and fron...

  • Page 73

    Supplemental seat-mounted side air bags (sab) supplemental seat-mounted side air bags (sab) may provide enhanced protection to help protect an occupant during a side impact. The sab is marked with an air bag label sewn into the outboard side of the seats. When the air bag deploys, it opens the seam ...

  • Page 74

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the sab and sabic air bags during deployment could cause you to be severely injured or killed. • should a vehicle rollover occur, the pretensioners and/or sab and sabic ...

  • Page 75

    Warning! • your vehicle is equipped with left and right sabic, do not stack luggage or other cargo up high enough to block the location of the sabic. The area where the side curtain air bag is located should remain free from any obstructions. • do not use accessory seat covers or place objects betwe...

  • Page 76

    Along with seat belts and pretensioners, advanced front air bags work with the supplemental driver and pas- senger side knee air bags and the knee bolsters to provide improved protection for the driver and front passenger. Side air bags also work with seat belts to improve occupant protection. Suppl...

  • Page 77

    Including the severity and type of collision. Advanced front air bags and supplemental driver and front passenger knee air bags are not expected to reduce the risk of injury in rear, side, or rollover collisions. The advanced front air bags and supplemental driver and front passenger knee air bags w...

  • Page 78

    The orc contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. Also, the orc turns on the air bag warning light in the instrument panel for approxi- mately four to eight seconds for a self-check when the igni...

  • Page 79

    • occupant classification module (ocm) located in the front passenger seat • ocs sensor located in the front passenger seat • air bag warning light the ocs will not prevent deployment of the passenger advanced front air bag. The ocs may reduce the inflation rate of the passenger advanced front air b...

  • Page 80

    Warning! • never place a rear facing infant seat in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. • children 12 years or younger should always ride buckled up in ...

  • Page 81

    Warning! Occupants in the front passenger seat sitting improp- erly may cause the ocs to not classify the passen- ger’s weight accurately. This may result in serious injury or death in a collision. Always wear your seat belt and sit properly, with the seat back in an upright position, your back agai...

  • Page 82

    The ocs may not classify the front passenger properly if: • the front passenger’s weight is transferred to another part of the vehicle (like the door, arm rest or instru- ment panel) • the front passenger leans forward, sideways or turns around • the front passenger seatback is not in the full uprig...

  • Page 83

    Not seated properly not seated properly 2 things to know before starting your vehicle 81.

  • Page 84

    Not seated properly not seated properly 82 things to know before starting your vehicle.

  • Page 85

    S warning! Placing an object on the floor under the front pas- senger seat may prevent the ocs from working properly, which may result in serious injury or death in a collision. Do not place any objects on the floor under the front passenger. The air bag warning light will turn on whenever the ocs i...

  • Page 86

    Warning! Make sure that objects inside the flip ’n stow™ front passenger seat storage bin do not interfere with the latch before closing the seat. In addition, after closing the front passenger seat storage bin, make sure the front passenger seat cushion is pushed downward and fully latched to the b...

  • Page 87

    Warning! (continued) passenger if the vehicle is involved in a collision. A modified vehicle may not comply with required federal motor vehicle safety standards (fmvss) and/or canadian motor vehicle safety standards (cmvss). Driver and passenger advanced front air bag inflator units the driver and p...

  • Page 88

    Air bag deploys down and around the knee blocker/ glove box surface allowing the air bags to inflate to the full size. The air bags fully inflate in about 15 to 20 milliseconds. Supplemental seat-mounted side air bag (sab) inflator units the supplemental seat-mounted side air bags are de- signed to ...

  • Page 89

    Where the sabic inflates. This especially applies to children. The sabic is only about 3-1/2 in (9 cm) thick when it is inflated. Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of whether or not an air bag should have deployed. Note: in a ro...

  • Page 90

    If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or al...

  • Page 91

    Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! Deployed air bags and seat belt pretensioners can not protect you in another collision. Have the air bags, seat belt pretensioners, and t...

  • Page 92

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion,...

  • Page 93

    • the air bag warning light remains on after the four to eight-second interval. • the air bag warning light comes on intermittently or remains on while driving. Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be dis...

  • Page 94

    Note: edr data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the edr under normal driving conditions and no per- sonal data (e.G., name, gender, age, and crash location) are recorded. However, other parties, such as law en- forcement, could combin...

  • Page 95

    Before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. You should also make sure that you can install it in the vehicle where you will use it. Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck. ...

  • Page 96

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 97

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 98

    Have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above t...

  • Page 99

    Integrated child booster seat — if equipped the integrated child booster seat is located in each outboard second-row passenger seat. The booster seat is designed for children weighing between 48 and 85 lbs (22 and 39 kg) and between 47 in (119 cm) and 57 in (145 cm) tall. To position a child into th...

  • Page 100

    Warning! Securely lock the seat cushion into position before using the seat. Otherwise, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat cushion could cause serious injury. Children too large for booster seats children who are large enough ...

  • Page 101

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 102

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 103

    Latch-equipped child seats without using the vehicle’s seat belts. Some seating positions may have a top tether anchorage but no lower anchorages. In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint. Please see the following table for m...

  • Page 104

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 105

    Can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information. Can the head restraints be removed?...

  • Page 106

    Locating the latch anchorages in addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to...

  • Page 107

    Center seat latch this vehicle has 5 lower latch anchorages in the rear seat. Anchorages a and b are used for the right outboard position behind the front passenger (1). Anchorages d and e are used for the left outboard position behind the driver (3). Anchorages c and d are used for the center seati...

  • Page 108

    And buckle, the center seat belt can be used to restraint an occupant or child restraint in the center seating position. 2. Right outboard and center seating positions (1 and 2): install the first child seat in the right outboard seating position using lower anchorages a and b. Install the second ch...

  • Page 109

    Warning! (continued) • if you are installing three child restraints next to each other, you must use the seat belt and the center tether anchor for the center position. You must use the latch anchors to install the child seat in position (3), behind the driver. You may use either the latch anchors o...

  • Page 110

    4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 5. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 111

    The child restraint installation, instead of buckling it behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. Do not lock the seatbelt. Remind all children in the vehicle that the seat belts are not toys and that they should not play with them. Wa...

  • Page 112

    Into the retractor. For additional information on alr, refer to the “automatic locking mode” description un- der “occupant restraints.” the cinching latch plate is designed to hold the lap portion of the seatbelt tight when webbing is pulled tight and straight through a child restraint’s belt path. ...

  • Page 113

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for- ward facing child restrai...

  • Page 114

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 115

    8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test...

  • Page 116

    4. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat. 5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether str...

  • Page 117

    Installing child restraints using the top tether anchorage 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for t...

  • Page 118

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly be- hind the child seat to secure a child restraint top tether strap. If your vehicle is equipped with a split rear seat, make sure the tether ...

  • Page 119

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of diff...

  • Page 120

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 121

    Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat b...

  • Page 122

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 123

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 125: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 ▫ inside day/night mirror . . . . . . . . . . . . . . . .130 ▫ automatic dimming mirror — if equipped . . .130 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . .132 ▫ p...

  • Page 126

    ▫ head restraints . . . . . . . . . . . . . . . . . . . . . .154 ▫ 60/40 split folding rear seat with fold-flat feature . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 䡵 driver memory seat — if equipped . . . .159 ▫ programming the memory feature . . . . . . . . .159 ▫ linking and unlinki...

  • Page 127

    ▫ interior lights . . . . . . . . . . . . . . . . . . . . . . .173 ▫ battery saver feature . . . . . . . . . . . . . . . . . .175 䡵 windshield wipers and washers . . . . . .175 ▫ windshield wiper operation . . . . . . . . . . . . .176 ▫ intermittent wiper system . . . . . . . . . . . . . . .177 ▫ wi...

  • Page 128

    ▫ to resume . . . . . . . . . . . . . . . . . . . . . . . . . .196 ▫ to vary the speed setting . . . . . . . . . . . . . . .197 ▫ setting the following distance in acc . . . . . .198 ▫ overtake aid . . . . . . . . . . . . . . . . . . . . . . . .202 ▫ acc operation at stop . . . . . . . . . . . . . ....

  • Page 129

    ▫ parksense® system usage precautions. . . . . . .239 䡵 parksense® front and rear park assist — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .241 ▫ parksense® sensors . . . . . . . . . . . . . . . . . . . .243 ▫ parksense® warning display . . . . . . . . . . . . .244 ▫ parksense® disp...

  • Page 130

    ▫ using homelink®. . . . . . . . . . . . . . . . . . . . .282 ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . .282 ▫ troubleshooting tips . . . . . . . . . . . . . . . . . . .282 ▫ general information. . . . . . . . . . . . . . . . . . . .283 䡵 power sunroof with power shade — if eq...

  • Page 131

    ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . .293 ▫ sky slider™ maintenance . . . . . . . . . . . . . . . .294 䡵 electrical power outlets . . . . . . . . . . .294 䡵 power inverter — if equipped . . . . . . . .297 䡵 wireless charging pad — if equipped . .298 ▫ wireless charging pad op...

  • Page 132

    Mirrors inside day/night mirror a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjus...

  • Page 133

    Left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you. Note: • the automatic dimming mirror feature is disabled when the vehicle is in reverse gear to improve re...

  • Page 134

    Assist call the rear view mirror contains an assist push button which automatically connects the vehicle occupants to one of several predefined locations for immediate sup- port: • roadside assistance – if you get a flat tire, or need a tow, just press the assist button and you’ll be con- nected to ...

  • Page 135

    Note: the passenger side convex outside mirror will give a much wider view to the rear, and especially of the lane next to your vehicle. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your pass...

  • Page 136

    Models with express window feature press and release the mirror select button marked l (left) or r (right) and then press one of the four arrow buttons to move the mirror in the direction the arrow is pointing. The selection will time out after 30 seconds of inactivity to guard against accidentally ...

  • Page 137

    • the mirrors are accidentally manually folded/unfolded. • the mirrors come out of the unfolded position. • the mirrors shake and vibrate at normal driving speeds. To reset the power folding mirrors : fold and unfold them by pressing the button. (this may require multiple button pushes). This resets...

  • Page 138

    Sun visor “slide-on-rod” feature — if equipped the sun visor “slide-on-rod” feature allows for addi- tional flexibility in positioning the sun visor to block out the sun. 1. Fold down the sun visor. 2. Unclip the visor from the center clip. 3. Pull the sun visor toward the inside rearview mirror to ...

  • Page 139

    The bsm detection zone covers approximately one lane on both sides of the vehicle (12 ft or 3.8 m). The zone starts at the outside rear view mirror and extends ap- proximately 23 ft (7 m) to the rear of the vehicle. The bsm system monitors the detection zones on both sides of the vehicle when the ve...

  • Page 140

    The bsm system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary. The bsm system will issue an alert during these types of zone entries. Entering from the side vehicles that move into your adjacent lanes from either side o...

  • Page 141

    Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Overtaking traffic if you pass another vehicle slowly (with a relative speed less than 15 mph (24 km/h) and the vehicle remains ...

  • Page 142

    Overtaking/approaching overtaking/passing 140 understanding the features of your vehicle.

  • Page 143

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The bsm system will not alert you of objects t...

  • Page 144

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicles mirrors, glance over your shoulder...

  • Page 145

    Note: in a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When rcp is on and the vehicle is in reverse, the driver is alerted using both the visua...

  • Page 146

    Blind spot alert lights/chime when operating in blind spot alert lights/chime mode, the bsm system will provide a visual alert in the appro- priate side view mirror based on a detected object. If the turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, a...

  • Page 147

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 148

    Reclining the seatback forward or rearward the seatback can be reclined both forward and rearward. Push the seat recliner switch forward or rearward, the seatback will move in the direction of the switch. Release the switch when the desired position has been reached. Warning! Do not ride with the se...

  • Page 149

    Manual seats — if equipped manual front seat forward/rearward adjustment on models equipped with manual seats, the adjusting bar is located at the front of the seats, near the floor. Power lumbar switch front seat adjustment 3 understanding the features of your vehicle 147.

  • Page 150

    While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! • adjusting a seat while driving...

  • Page 151

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Manual seat height adjustment — if equipped the driver’s seat height can be raised or ...

  • Page 152

    Heated seats — if equipped on some models, the front and rear seats may be equipped with heaters located in the seat cushions. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or o...

  • Page 153

    Note: once a heat setting is selected, heat will be felt within two to five minutes. When the hi-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal hi-level. If the hi-level setting is sele...

  • Page 154

    Note: once a heat setting is selected, heat will be felt within two to five minutes. When the hi-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal hi-level. If the hi-level setting is sele...

  • Page 155

    Front ventilated seats with uconnect® 8.4a/8.4an — if equipped on some models, both the driver and passenger seats are ventilated. Located in the seat cushion and seatback are small fans that draw the air from the passenger compart- ment and pull air through fine perforations in the seat cover to he...

  • Page 156

    Vehicles equipped with remote start on models that are equipped with remote start, the driver’s ventilated seat can be programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to know before starting your vehicle” for further information. Head restraint...

  • Page 157

    The ahrs will automatically return to their normal position following a rear impact. If the ahrs do not return to their normal position see your authorized dealer immediately. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located ...

  • Page 158

    Warning! Do not place items over the top of the active head restraint, such as coats, seat covers or portable dvd players. These items may interfere with the operation of the active head restraint in the event of a collision and could result in serious injury or death. Rear head restraints the rear ...

  • Page 159

    Note: prior to folding the rear seat, it may be necessary to position the front seat to its mid-track position. Also, be sure that the front seats are fully upright and posi- tioned forward. This will allow the rear seat to fold down easily. Warning! • it is extremely dangerous to ride in a cargo ar...

  • Page 160

    To raise the rear seat note: if interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Raise the seatback and lock it into place. Warning! Be certain that the seatback is securely locked into position. If the sea...

  • Page 161

    Driver memory seat — if equipped this feature allows the driver to store up to two different memory profiles, for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat and side mirrors and a set of desired radio station presets. The memory sw...

  • Page 162

    2. Adjust all memory profile settings to desired prefer- ences (i.E., seat, side mirror and radio station presets). 3. Press and release the set button on the memory switch, then press the side of the number (1) button within five seconds. The electronic vehicle informa- tion center (evic), if equip...

  • Page 163

    Linking and unlinking the remote keyless entry transmitter to memory your remote keyless entry (rke) transmitters can be programmed to recall one of two pre-programmed memory profiles with a press of the unlock button on the rke transmitter. Note: before programming your rke transmitters you must se...

  • Page 164

    Memory position recall note: • for vehicles equipped with an automatic transmission, the vehicle must be in park to recall memory posi- tions. If a recall is attempted when the vehicle is not in park, a message will display in the evic, if equipped. • for vehicles equipped with a manual transmission...

  • Page 165

    The distance the driver seat moves depends on where you have the driver seat positioned when you remove the key from the ignition switch. • when you remove the key from the ignition switch, the driver seat will move about 2.4 in (60 mm) rear- ward if the driver’s seat position is greater than or equ...

  • Page 166

    To open and close the hood two latches must be released to open the hood. 1. Pull the hood release lever located under the drivers side of the instrument panel. 2. Move to the outside of the vehicle and pull the safety latch release lever forward (toward you). The safety latch release lever is locat...

  • Page 167

    Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood is fu...

  • Page 168

    Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Rotate the headlight switch to the second detent for headlight, parking light and instrument panel light op- eration. Automatic headlights — if equipped this system automatically turns t...

  • Page 169

    Headlights on with wipers (available with automatic headlights only) when this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the headlight switch is placed in the auto position. In addition, the headlights will turn off when the wipers are ...

  • Page 170

    If you turn the headlights off before the ignition, they will turn off in the normal manner. Note: • the lights must be turned off within 45 seconds of placing the ignition in the off position to activate this feature. • the headlight delay time is programmable using the uconnect® system, refer to “...

  • Page 171

    Note: • automatic high beam headlamp control can be turned on or off using the uconnect® system, refer to “uconnect® settings” in “understanding your instru- ment panel” for further information. • broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause head...

  • Page 172

    Fog lights — if equipped the front fog light switch is built into the headlight switch. To activate the front fog lights, turn on the parking lights or the low beam headlights and press the headlight switch. To turn off the front fog lights, either press the headlight switch a second time or turn of...

  • Page 173

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: • if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside...

  • Page 174

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/low beam switch push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction le...

  • Page 175

    There are courtesy lights located above the front seats. If your vehicle is equipped with a power sunroof the courtesy lights are located above the rear seats. The courtesy lights can be turned on by pressing the lens. To turn the lights off, press the lens a second time. Interior lights the interio...

  • Page 176

    With the parking lights or headlights on, rotating the right dimmer control upward will increase the brightness of the instrument panel lights and lighted cupholders — if equipped. Ambient light control rotate the dimmer control upward or downward to increase or decrease the brightness of the ambien...

  • Page 177

    Dome light position rotate the instrument panel dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the instrument panel dimmer control is in this position. Interior light defeat (off) rotate the instrument panel dimmer contro...

  • Page 178

    Windshield wiper operation rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation. Windshield wiper/washer lever windshield wiper operation 176 understanding the features ...

  • Page 179

    Caution! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur. Intermittent wiper system use one of the...

  • Page 180

    Windshield washer operation to use the washer, pull the lever rearward toward you and hold while spray is desired. If the lever is pulled while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the lever is released, and then resume the intermittent inter...

  • Page 181

    Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist use the mist...

  • Page 182

    Rain sensing wipers — if equipped this feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of ...

  • Page 183

    The rain sensing system has protection features for the wiper blades and arms, and will not operate under the following conditions: • low ambient temperature — when the ignition is first turned on, the rain sensing system will not operate until the wiper switch is moved, vehicle speed is greater tha...

  • Page 184

    To unlock the steering column, push the control handle downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as de- sired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering col...

  • Page 185

    Heated steering wheel — if equipped the steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate up to 80 minutes before automatically shutting o...

  • Page 186

    Uconnect® 8.4 system — if equipped touch the “controls” soft-key then touch the “heated steering wheel” soft-key to turn on the heated steering wheel. Press the “heated steering wheel” soft-key a second time to turn the heated steering wheel off. Note: the engine must be running for the heated steer...

  • Page 187

    Vehicles equipped with remote start on models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to know before starting your vehicle” for further information. Warning! • person...

  • Page 188

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 189

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 190

    Pressing the set (+) button once will result in a 1 mph (1 km/h) increase in set speed. Each subsequent tap of the button results in an increase of 1 mph (1 km/h). To decrease speed while the electronic speed control is set, push the set (-) button. If the button is continually held in the set (-) p...

  • Page 191

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 192

    Warning! • adaptive cruise control (acc) is a convenience system. It is not a substitute for active driving involvement. It is always the driver’s responsibil- ity to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead; and, most importantly, brake ope...

  • Page 193

    Warning! (continued) • when entering a turn lane or highway off ramp; when driving on roads that are winding, icy, snow- covered, slippery, or have steep uphill or downhill slopes. • when towing a trailer up or down steep slopes. • when circumstances do not allow safe driving at a constant speed. Th...

  • Page 194

    Note: any chassis/suspension or tire size modifica- tions to the vehicle will effect the performance of the adaptive cruise control. Activating adaptive cruise control (acc) you can only engage acc if the vehicle speed is above 0 mph (0 km/h). The minimum set speed for the acc system is 20 mph (32 k...

  • Page 195

    Note: you cannot enable acc under the following conditions: • when in four-wheel drive low. • when you apply the brakes. • when the parking brake is set. • when the automatic transmission is in park, re- verse or neutral. • when the vehicle speed is outside of the speed range. • when the brakes are ...

  • Page 196

    To turn the system off, push and release the adaptive cruise control (acc) on/off button again. At this time, the system will turn off and the evic will display “adaptive cruise control (acc) off.” warning! Leaving the adaptive cruise control (acc) system on when not in use is dangerous. You could a...

  • Page 197

    If the system is set when the vehicle speed is below 20 mph (32 km/h), the set speed shall be defaulted to 20 mph (32 km/h). If the system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle. Note: acc cannot be set if there is a stationar...

  • Page 198

    To turn off the system will turn off and clear the set speed in memory if: • you push the adaptive cruise control (acc) on/ off button. • you push the normal (fixed speed) cruise control on/off button. • you turn off the ignition. • you switch to four-wheel drive low. To resume if there is a set spe...

  • Page 199

    To vary the speed setting while acc is set, you can increase the set speed by pressing the set + button. Pressing the set + button once will result in a 1 mph (1 km/h) increase in set speed. Each subsequent tap of the button results in an increase of 1 mph (1 km/h). If the set + button is continuall...

  • Page 200

    • the acc system maintains set speed when driving up hill and down hill. However, a slight speed change on moderate hills is normal. In addition, downshifting may occur while climbing uphill or descending down- hill. This is normal operation and necessary to main- tain set speed. When driving up hil...

  • Page 201

    Distance setting 3 bars (long) distance setting 2 bars (medium) 3 understanding the features of your vehicle 199.

  • Page 202

    To increase the distance setting, press the distance set- ting — increase button and release. Each time the button is pressed, the distance setting increases by one bar (longer). To decrease the distance setting, press the distance setting — decrease button and release. Each time the button is press...

  • Page 203

    • the distance setting is changed. • the system disengages. (refer to the information on acc activation). The maximum braking applied by acc is limited; how- ever, the driver can always apply the brakes manually, if necessary. Note: the brake lights will illuminate whenever the acc system applies th...

  • Page 204

    Overtake aid when driving with acc engaged and following a target vehicle, the system will provide an additional accelera- tion to assist in passing vehicles in front. This additional acceleration is triggered when the driver utilizes the left turn signal. In locations with left hand drive traffic, ...

  • Page 205

    Warning! When the acc system is resuming speed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle. Failure to follow these warnings can result in a collision and death or serious personal injury. Adaptive cruise control (acc) menu the evic displays ...

  • Page 206

    • system off • acc proximity warning • acc unavailable warning • the evic will return to the last display selected after five seconds of no acc display activity. Display warnings and maintenance “wipe front radar sensor in front of vehicle” warning the “acc / fcw unavailable wipe front radar sensor”...

  • Page 207

    If weather conditions are not a factor, the driver should examine the sensor. It may require cleaning or removal of an obstruction. The sensor is located in the center of the vehicle behind the lower grille. To keep the acc system operating properly, it is impor- tant to note the following maintenan...

  • Page 208

    “clean front windshield” warning the “acc / fcw limited functionality clean front windshield” warning will display and also a chime will indicate when conditions temporarily limit system per- formance. This most often occurs at times of poor visibil- ity, such as in snow or heavy rain and fog. The a...

  • Page 209

    Service acc/fcw warning if the system turns off, and the evic displays “acc/ fcw unavailable service required”or “cruise/fcw unavailable service required”, there may be an internal system fault or a temporary malfunction that limits acc functionality. Although the vehicle is still drivable under nor...

  • Page 210

    Turns and bends when driving on a curve with acc engaged, the system may decrease the vehicle speed and acceleration for stability reasons, with no target vehicle detected. Once the vehicle is out of the curve the system will resume your original set speed. This is a part of normal acc system functi...

  • Page 211

    Using acc on hills when driving on hills, acc may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, acc perfor- mance may be limited. Lane changing acc may not detect a vehicle until it is completely in the lane in which you ...

  • Page 212

    Narrow vehicles some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead. 210 understanding the features of your vehicle.

  • Page 213

    Stationary objects and vehicles acc does not react to stationary objects and stationary vehicles. For example, acc will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if nece...

  • Page 214

    (fixed speed) control off. Pressing of the normal (fixed speed) cruise control on/off button will result in turning on (changing to) the normal (fixed speed) cruise control mode. Warning! In the normal (fixed speed) cruise control mode, the system will not react to vehicles ahead. Be sure to maintai...

  • Page 215

    Set speed will continue to increase in 5 mph (10 km/h) increments until the button is released. The increase in set speed is reflected in the evic display. To decrease speed while the normal (fixed speed) cruise control is set, push the set (-) button. If the button is continually held in the set (-...

  • Page 216

    To turn off the system will turn off and erase the set speed in memory if: • you push the normal (fixed speed) cruise control on/off button. • you turn off the ignition. • you engage four-wheel drive low. • you push the adaptive cruise control (acc) on/off button. Forward collision warning (fcw) wit...

  • Page 217

    Note: fcw monitors the information from the forward looking sensors as well as the electronic brake controller (ebc), to calculate the probability of a forward collision. When the system determines that a forward collision is probable, the driver will be provided with audible and visual warnings and...

  • Page 218

    Note: • the minimum speed for fcw activation is 5 mph (10 km/h). • the fcw alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course prediction. This is expected and is a part of normal fcw activation and functionality. • it is unsafe to test the fc...

  • Page 219

    To turn the fcw system off, press the forward collision button once to turn the system off (led turns on). To turn the fcw system back on, press the forward collision button again to turn the system on (led turns off). • changing the fcw status to “off” prevents the system from warning you of a poss...

  • Page 220

    Changing fcw and active braking status to change the fcw sensitivity and active braking settings with uconnect® 8.4/8.4a system screen — if equipped. Follow these steps to set the fcw sensitivity and active braking: note: the settings can only be changed when the vehicle is in park. 1. Press the “co...

  • Page 221

    5. Press the “fwd collision warning” far or near soft-key for your desired preference. Then press the back arrow. 6. Press the second “fwd collision w...” soft-key. 7. Press the “active braking” on or off soft-key. The default status of fcw is the “far” setting and the active braking is the “on” set...

  • Page 222

    Once the condition that limited the system performance is no longer present, the system will return to its full performance state. If the problem persists, see your authorized dealer. Service fcw warning if the system turns off, and the evic displays: • acc/fcw unavailable service required • cruise/...

  • Page 223

    The driver may manually override the haptic warning by applying torque into the steering wheel at any time. When only a single lane marking is detected and the driver unintentionally drifts across the lane marking (no turn signal applied), the lanesense system provides a visual warning through the i...

  • Page 224

    To turn the lanesense system on, press the lanesense button to turn the system on (led turns off). A “lane sense on” message is shown in the evic. To turn the lanesense system off, press the lanesense button once to turn the system off (led turns on). Note: the lanesense system will retain the last ...

  • Page 225

    Left lane departure — only left lane detected • when the lanesense system is on, the lanesense indicator is solid white when only the left lane mark- ing has been detected and the system is ready to provide visual warnings in the evic if an uninten- tional lane departure occurs. • when the lanesense...

  • Page 226

    Note: the lanesense system operates with the similar behavior for a right lane departure when only the right lane marking has been detected. Left lane departure — both lanes detected • when the lanesense system is on, the lane lines turn from gray to white to indicate that the lane markings have bee...

  • Page 227

    • for example: if approaching the left side of the lane the steering wheel will turn to the right. • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left lane line flashes from a thin yellow line to thick yellow line and the lanesense indicator...

  • Page 228

    Note: the lanesense system operates with the similar behavior for a right lane departure. 7.0 evic screen — if equipped when the lanesense system is on; the lane lines are gray when the lane boundaries have not been detected and the lanesense indicator is solid white. Lane approached (flashing thin ...

  • Page 229

    Left lane departure — only left lane detected • when the lanesense system is on, the lanesense indicator is solid white when only the left lane mark- ing has been detected and the system is ready to provide visual warnings in the evic if an uninten- tional lane departure occurs. • when the lanesense...

  • Page 230

    Left lane departure — both lanes detected • when the lanesense system is on, the lane lines turn from gray to white to indicate that the lane markings have been detected. The lanesense indicator is solid green when both lane markings have been detected and the system is “armed” to provide visual war...

  • Page 231

    • for example: if approaching the left side of the lane the steering wheel will turn to the right. • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes thick yellow to thin yellow. The lanesense indicator changes from ...

  • Page 232

    Note: the lanesense system operates with the similar behavior for a right lane departure. Changing lanesense status the lanesense system settings can be configured through the uconnect® system screen. Follow these steps to change the lanesense settings: 1. Press the “controls” soft-key located on th...

  • Page 233

    Note: • when enabled the system operates above 37 mph (60 km/h) and below 112 mph (180 km/h). • use of the turn signal suppresses the warnings. • the system will not apply torque to the steering wheel whenever a safety system engages. (anti-lock brakes, traction control system, electronic stability ...

  • Page 234

    (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orienta- tion of the obstacle. Parksense® warning display the parksense® warning screen will only be displayed if sound and display is selected from the customer - programmable features section of t...

  • Page 235

    Single 1/2 second tone/solid arc slow tone/solid arc 3 understanding the features of your vehicle 233.

  • Page 236

    Slow tone/solid arc fast tone/flashing arc 234 understanding the features of your vehicle.

  • Page 237

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: fast tone/flashing arc continuous tone/flashing arc 3 understanding the features of you...

  • Page 238

    Warning alerts rear dis- tance (in/cm) greater than 79 in (200 cm) 79-59 in (200-150 cm) 59-47 in (150-120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) arcs — left none none none none none 2nd flash- ing 1st flashing arcs — center none 6th solid 5th soli...

  • Page 239

    Note: parksense® will reduce the volume of the radio, if on, when the system is sounding an audio tone. Enabling and disabling parksense® parksense® can be enabled and disabled with the parksense® switch, located on the switch panel below the uconnect® display. When the parksense® switch is pressed ...

  • Page 240

    Reverse and the system is disabled, the evic will display the “parksense off” message for as long as the vehicle is in reverse. The parksense® switch led will be on when parksense® is disabled or requires service. The parksense® switch led will be off when the system is enabled. If the parksense® sw...

  • Page 241

    Cleaning the parksense® system clean the parksense® sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could dam- age the sensors. Parksense® system usage precautions note: • ensure that the rear bumper is free of s...

  • Page 242

    System misinterpreting a close object as a sensor problem, causing the “parksense unavailable service required” message to be displayed in the evic. • on vehicles equipped with a tailgate, parksense® should be disabled when the tailgate is in the lowered or open position and the vehicle is in revers...

  • Page 243

    Warning! (continued) • before using parksense®, it is strongly recom- mended that the ball mount and hitch ball assem- bly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be...

  • Page 244

    • automatic brakes will not be available if esc is not available. • automatic brakes will not be available if there is a faulted condition detected with the parksense® park assist system or the braking system module. • the automatic braking function may only be applied if the vehicle deceleration is...

  • Page 245

    Parksense® will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the on/run position. Parksense® can be active only when the shift lever is in reverse or drive (non-reverse for manual trans- mission). If parksense® is enabled at one of t...

  • Page 246

    Parksense® warning display the parksense® warning screen will only be displayed if sound and display is selected from the customer - programmable features section of the uconnect® sys- tem. Refer to ⬙ uconnect® settings” in “understanding your instrument panel” for further information. The parksense...

  • Page 247

    If an obstacle is detected in the left and/or right rear region, the display will show a single flashing arc in the left and/or right rear region and will produce a fast sound tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the...

  • Page 248

    Slow tone/solid arc fast tone/flashing arc 246 understanding the features of your vehicle.

  • Page 249

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: fast tone/flashing arc continuous tone/flashing arc 3 understanding the features of you...

  • Page 250

    Warning alerts rear dis- tance (in/cm) greater than 79 in (200 cm) 79-59 in (200-150 cm) 59-47 in (150-120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) arcs — left none none none none none 2nd flash- ing 1st flashing arcs — center none 6th solid 5th soli...

  • Page 251

    Radio vol- ume re- duced no yes yes yes yes yes yes note: parksense® will reduce the volume of the radio, if on, when the system is sounding an audio tone. Front park assist when the vehicle is in drive or non-reverse for manual transmission, the parksense warning screen will be displayed when an ob...

  • Page 252

    No tone/solid arc no tone/flashing arc 250 understanding the features of your vehicle.

  • Page 253

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: fast tone/flashing arc continuous tone/flashing arc 3 understanding the features of you...

  • Page 254

    Warning alerts front distance (in/cm) greater than 47 in (120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) arcs — left none none none 2nd flashing 1st flashing arcs — center none 4th solid 3rd flashing 2nd flashing 1st flashing arcs — right none none non...

  • Page 255

    If the uconnect® system is equipped, chime volume settings will not be accessible from the evic. The chime volume settings include low, medium, and high. The factory default volume setting is medium. Parksense will retain its last known configuration state through ignition cycles. Enabling and disab...

  • Page 256

    Reverse and the system is disabled, the evic will display the “parksense off” message for as long as the vehicle is in reverse. The parksense® switch led will be on when parksense® is disabled or requires service. The parksense® switch led will be off when the system is enabled. If the parksense® sw...

  • Page 257

    If ⬙ parksense unavailable wipe rear sensors ⬙ or ⬙ parksense unavailable wipe front sen- sors ⬙ appears in the electronic vehicle information center (evic) make sure the outer surface and the underside of the rear fascia/bumper and/or front fascia/ bumper is clean and clear of snow, ice, mud, dirt ...

  • Page 258

    • parksense®, when on, will reduce the volume of the radio when it is sounding a tone. • clean the parksense® sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not workin...

  • Page 259

    Caution! (continued) • the vehicle must be driven slowly when using parksense® in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using parksense®. Warning! • drivers must be careful when backing up even when using par...

  • Page 260

    Providing audible/visual instructions, and controlling the steering wheel. The parksense® active park assist system is defined as “semi-automatic” since the driver maintains control of the accelerator, shift lever and brakes. Depending on the driver’s parking maneuver selection, the parksense® activ...

  • Page 261

    To enable the parksense® active park assist system, press the parksense® active park assist switch once (led turns on). To disable the parksense® active park assist system, press the parksense® active park assist switch again (led turns off). The parksense® active park assist system will turn off au...

  • Page 262

    • performing 6 parking attempts to position the vehicle into the parking space. The parksense® active park assist system will only operate and search for a parking space when the follow- ing conditions are present: • gear position is in drive (automatic transmission) or in a forward gear (manual tra...

  • Page 263

    Display. You may switch to perpendicular parking if you desire. Push the ok button on the left side steering wheel switch to change your parking space setting. Note: • when searching for a parking space, use the turn signal indicator to select which side of the vehicle you want to perform the parkin...

  • Page 264

    When an available parking space has been found, and the vehicle is not in position, you will be instructed to move forward to position the vehicle for a parallel parking sequence. Once the vehicle is in position, you will be instructed to place the shift lever into the reverse position. When the dri...

  • Page 265

    Note: • it is the driver’s responsibility to use the brake and accelerator during the semi-automatic parking maneu- ver. • when the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly. • the parksense® acti...

  • Page 266

    When the vehicle has been moved into the parallel park position you will be instructed to place the shift lever into the drive position, move forward slowly and check your surroundings. After moving forward and checking your surroundings you may be instructed to place the shift lever into the revers...

  • Page 267

    Your vehicle is now in the parallel park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to park. The ⬙ active parksense complete - check parking position ⬙ message...

  • Page 268

    Wheel switch to change your parking space setting to a perpendicular maneuver. You may switch back to paral- lel parking if you desire. Note: • when searching for a parking space, use the turn signal indicator to select which side of the vehicle you want to perform the parking maneuver. The parksens...

  • Page 269

    When an available parking space has been found, and the vehicle is not in position, you will be instructed to move forward to position the vehicle for a perpendicular parking sequence. Once the vehicle is in position you will be instructed to place the shift lever into the reverse position. When the...

  • Page 270

    Note: • it is the driver’s responsibility to use the brake and accelerator during the semi-automatic parking maneu- ver. • when the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly. • the parksense® acti...

  • Page 271

    When the vehicle has been moved into the perpendicular park position you will be instructed to place the shift lever into the drive position, move forward slowly, and check your surroundings. After moving forward and checking your surroundings you may be instructed to place the shift lever into the ...

  • Page 272

    Your vehicle is now in the perpendicular park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to park. The ⬙ active parksense complete - check parking position ⬙ me...

  • Page 273

    Caution! • the parksense® active park assist system is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in cl...

  • Page 274

    Warning! (continued) • before using the parksense® active park assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles beca...

  • Page 275

    Vehicle is shifted into park or the ignition is switched to the off position. A touch screen control (soft button) to disable display of the camera image is made available when the vehicle is not in reverse gear. Display of the camera image after shifting out of reverse can be disabled via a touch s...

  • Page 276

    Warning! Drivers must be careful when backing up even when using the parkview® rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your ...

  • Page 277

    4. Press the check box soft key next to “parkview® backup camera” to enable/disable. Note: a check mark will appear in the selection box to indicate the system is turned on. Turning parkview® on or off — with uconnect® 8.4a/8.4an 1. Press the “controls” soft-key located on the bottom of the uconnect...

  • Page 278

    Note: homelink® is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recom...

  • Page 279

    Note: • erasing all channels should only be performed when programming homelink® for the first time. Do not erase channels when programming additional buttons. • if you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the internet at www.Homelink.Com for informat...

  • Page 280

    2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keeping the homelink® indicator light in view. 3. Simultaneously press and hold both the homelink® button you want to program and the hand-held trans- mitter button. 4. Continue to hol...

  • Page 281

    Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink® button until the indicator light begins to flash after 20 seconds. Do not release the butto...

  • Page 282

    • to program the remaining two homelink® buttons, repeat each step for each remaining button. Do not erase the channels. Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Press and hol...

  • Page 283

    2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keeping the homelink® indicator light in view. 3. Continue to press and hold the homelink® button, while you press and release (“cycle”), your hand-held transmitter every two seconds u...

  • Page 284

    3. Without releasing the button proceed with “canadian/gate operator programming” step 2 and follow all remaining steps. Using homelink® to operate, press and release the programmed homelink® button. Activation will now occur for the programmed device (i.E., garage door opener, gate opera- tor, secu...

  • Page 285

    Warning! • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” fea...

  • Page 286

    Power sunroof with power shade — if equipped the power sunroof switch is located to the left between the sun visors on the overhead console. The power shade switch is located to the right between the sun visors on the overhead console. Power sunroof switch power shade switch 284 understanding the fe...

  • Page 287

    Warning! • never leave children unattended in a vehicle, and do not leave the key fob in or near the vehicle. Do not leave the ignition of a vehicle equipped with keyless enter-n-go™ in the acc or on/run mode. Occupants, particularly unattended chil- dren, can become entrapped by the power sunroof w...

  • Page 288

    Opening sunroof — manual mode a comfort stop position is a programmed automatic stop for the sunroof open position. The comfort stop position has been optimized to minimize wind buffeting. To open the sunroof, press and hold the switch rearward. The sunroof will stop automatically at the comfort sto...

  • Page 289

    Note: if the sunshade is in the closed position when the vent switch is pressed, the sunshade will automatically cycle to the halfway open position prior to the sunroof opening to the vent position. Opening power shade — express press the shade switch rearward and release it within one-half second a...

  • Page 290

    Closing power shade — manual mode to close the shade, press and hold the switch in the forward position. Any release of the switch will stop the movement and the shade will remain in a partially closed condition until the switch is pushed and held forward again. Pinch protect feature this feature wi...

  • Page 291

    Ignition off operation for vehicles not equipped with the electronic vehicle information center (evic) the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. For vehicles equipped with t...

  • Page 292

    Caution! (continued) • never attempt to open or close the sky slider™ when it is frozen. Wait until the sky slider™ is thawed before operating. • opening the sky slider™ when damp, wet, or dirty can cause stains, mildew, and damage to the soft- top material and the inside of your vehicle. Make sure ...

  • Page 293

    Warning! (continued) • if potential danger exists while opening or closing the sky slider™ in automatic mode, press and release the switch immediately to interrupt the operation. • if potential danger exists while opening or closing the sky slider™ in operator mode, release the switch immediately to...

  • Page 294

    • to resume the operation from a partially open posi- tion, press and release the switch a second time. • the sky slider™ will not open from the front and the rear at the same time. The sky slider™ must close fully before opening it from the opposite end. Using operator mode press the switch rearwar...

  • Page 295

    Manual override the sky slider™ drive motors are mounted to the roof above the cargo lamp. In the event that your vehicle losses battery power, you can close the sky slider™ by turning the drive gears in the appropriate motor with a 6 mm allen wrench. To do so, you must first remove the cargo lamp f...

  • Page 296

    Sky slider™ maintenance refer to “sky slider™ top care” in “maintaining your vehicle” for further information. Electrical power outlets your vehicle is equipped with 12 volt (13 amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessori...

  • Page 297

    In addition to the front power outlet, there is also a power outlet located in the storage area of the center console. The rear power outlet is located in the right rear cargo area. Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted i...

  • Page 298

    Warning! (continued) • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in us...

  • Page 299

    Power inverter — if equipped there is a 115 volt, 150 watt inverter outlet located on the back of the center console to convert dc current to ac current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 watts. Certain high-end video games, su...

  • Page 300

    Warning! To avoid serious injury or death: • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Wireless charging pad — if equipped your vehicle may be equipped wi...

  • Page 301

    Your qi enabled mobile phone. Qi is a standard that uses magnetic induction to transfer power to your mobile device. Your mobile phone must be designed for qi wireless charging, be equipped with an aftermarket sleeve or equipped with a back plate from your mobile phone provider. The wireless chargin...

  • Page 302

    Note: the initial adjustment will only need to be done once as long as only one mobile phone is used. If a different mobile phone is used, the cradle will need to be readjusted. The led indicator will flash green while the mobile phone is charging. The qi enabled phone is able to function normally a...

  • Page 303

    Cupholders there are two cupholders for the front seat passengers, located in the center console. There are two cupholders for the rear seat passengers, located in the center armrest. Front cupholders rear cupholders 3 understanding the features of your vehicle 301.

  • Page 304

    Storage glove box storage compartment the glove box storage compartment is located on the passengers side of the instrument panel. Pull outward on the latch to open the storage compartment. There is also an additional storage bin located above the instrument panel in the center of the dash. Glove bo...

  • Page 305

    Console storage compartment some vehicles may be equipped with a wireless charging pad located in the upper portion of the center console. Refer to wireless charging pad-if equipped in this section for more information. To open, pull up on the latch and lift the cover. Upper console charging pad cen...

  • Page 306

    The center console has a storage area which can hold cell phones, pdas, and other small items. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of thes...

  • Page 307

    Rear storage bin the rear storage bins are located in the rear of the vehicle on the sides of the load floor. Cargo tie-down hooks and loops the tie-downs located on the cargo area floor should be used to secure loads safely when the vehicle is moving. Cargo tie-down loops are located on the trim pa...

  • Page 308

    Warning! The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. To avoid loss of control resulting in per- sonal injury, follow these guidelines for loading your vehicle: • do not carry loads that exceed the load limits described on the label a...

  • Page 309

    The removable retractable cargo area cover mounts in the cargo area behind the top of the rear seats. The cover, when extended, covers the cargo area to keep items out of sight. Notches in the trim panels near the liftgate opening secure the extended cover in place. The cover rolls away neatly insid...

  • Page 310

    Warning! In a collision, a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. D...

  • Page 311

    And operate for several wipe cycles after the end of the lever is released, and then resume the intermittent inter- val previously selected. If the lever is pushed while the wiper is in the off position, the wiper will operate for several wipe cycles, then turn off. Note: as a protective measure, th...

  • Page 312

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 313

    Caution! • to avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as pos- sible and secure the load appropriately. • long loads, which extend over the windshield, such as wood panels or surfboards, should be secured to...

  • Page 315: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .315 䡵 instrument cluster — base . . . . . . . . . .316 䡵 instrument cluster — premium . . . . . .317 䡵 instrument cluster descriptions . . . . .318 䡵 electronic vehicle information center (evic) . . . . . . ....

  • Page 316

    䡵 uconnect® radios — if equipped . . . . . . . .382 䡵 ipod®/usb/mp3 control — if equipped . .382 䡵 steering wheel audio controls — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .383 ▫ radio operation . . . . . . . . . . . . . . . . . . . . . .384 ▫ cd player . . . . . . . . . . . ....

  • Page 317

    Instrument panel features 1 — air demister outlet 5 — instrument cluster 9 — passenger air bag 13 — stop/start ignition button 2 — air outlet 6 — electronic speed controls 10 — glove compartment 14 — trunk release button 3 — electronic vehicle informa- tion center (evic) controls 7 — storage compart...

  • Page 318

    Instrument cluster — base 316 understanding your instrument panel.

  • Page 319

    Instrument cluster — premium 4 understanding your instrument panel 317.

  • Page 320

    Instrument cluster descriptions 1. Tachometer indicates the engine speed in revolutions per minute (rpm x 1000). 2. High beam indicator indicates that headlights are on high beam. 3. Front fog light indicator — if equipped this indicator will illuminate when the front fog lights are on. 4. Park/head...

  • Page 321

    When the appropriate conditions exist, this display shows the electronic vehicle information center (evic) messages. Refer to “electronic vehicle information center”. 6. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the...

  • Page 322

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the anti-lock brake system (abs), are also equipped with el...

  • Page 323

    Brakes. If the abs light does not turn on when the ignition switch is turned to the on/run position, have the light inspected by an authorized dealer. 8. Electronic stability control (esc) activation/ malfunction indicator light — if equipped the “esc activation/malfunction indicator light” in the i...

  • Page 324

    10. Speedometer indicates vehicle speed. 11. Seat belt reminder light when the ignition switch is first turned to the on/run position, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb ...

  • Page 325

    Possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that t...

  • Page 326

    Caution! (continued) equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can or balance beads if your vehic...

  • Page 327

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “maintaining your vehicle”. Follow the warnings unde...

  • Page 328

    Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warni...

  • Page 329

    This system allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The evic consists of the following: • speedometer • vehicle info • driver assist • fuel economy info • trip (trip a/trip b) • stop/start — if equipped • audio info • messag...

  • Page 330

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: • up arrow button press and release the up arrow button to scroll upward through the main menu and sub- menus (main gauge, mph/km/h, vehicle info, terrain, driver assist, fuel economy,...

  • Page 331

    • back/left arrow button press and release the left arrow button to access the information screens or sub-menu screens of a main menu item. • ok button press the ok button to access/select the information screens or sub-menu screens of a main menu item. Press and hold the ok arrow button for one sec...

  • Page 332

    If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the brake booster has been detected by the anti-lock brake system (abs) / el...

  • Page 333

    Operation of the brake warning light can be checked by turning the ignition switch from the off position to the on/run position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light ...

  • Page 334

    Messages that consist of approximately 60 possible warn- ing or information messages. These pop up messages fall into several categories: • five second stored messages when the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns...

  • Page 335

    5. Lane departure warning (ldw) — if equipped the lane departure warning (ldw) system provides the driver with visual and steering torque warnings when the vehicle starts to drift out of its lane unintentionally without the use of a turn signal. • when the ldw system is on and ready the lane lines a...

  • Page 336

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 337

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 7. Fuel gauge fuel gauge displays the level of fuel in the fuel tank when ...

  • Page 338

    Warning! If you continue operating the vehicle when the transmission temperature warning light is illumi- nated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. • low coolant level indicator this telltale will turn on to indicate the veh...

  • Page 339

    11. Dedicated speed warning telltale — if equipped this area displays the dedicated speed warn- ing telltale. 12. Speed for electronic cruise control setting this displays the set speed of the electronic speed control. 13. Reconfigurable telltale area • hill descent indicator — if equipped the symbo...

  • Page 340

    14. Reconfigurable telltale display • power steering system over temperature — if equipped if the “power steering system over temp” message and a icon are displayed on the evic screen, it indicates that extreme steer- ing maneuvers may have occurred, which caused an over temperature condition in the...

  • Page 341

    • oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on....

  • Page 342

    Required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • oil temperature warning light this telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon ...

  • Page 343

    Caution! (continued) “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear continuous chimes, turn the engine off immediately and call an autho- rized dealer for serv...

  • Page 344

    1. Lane departure warning (ldw) the lane departure warning (ldw) system provides the driver with visual and steering torque warnings when the vehicle starts to drift out of its lane unintentionally without the use of a turn signal. • when the ldw system is on and ready the lane lines and ldw indicat...

  • Page 345

    If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the brake booster has been detected by the anti-lock brake system (abs) / el...

  • Page 346

    Operation of the brake warning light can be checked by turning the ignition switch from the off position to the on/run position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light ...

  • Page 347

    Examples of this message type are “turn signal on” (if a turn signal is left on) and “lights on” (if driver leaves the vehicle). • unstored messages until run these messages deal primarily with the remote start feature. This message type is displayed until the ignition is in the run state. Examples ...

  • Page 348

    9. Reconfigurable telltale area • hill descent indicator — if equipped the symbol illuminates (is armed) when the 4wd low switch is activated and the transmis- sion range indicator is in low or reverse position (off-road mode). • selec speed control indicator — if equipped the symbol illuminates and...

  • Page 349

    11. Instructional area this area will display text to the visual warnings (i.E., “push brake to start”). 12. Amber reconfigurable telltale display • transmission temperature warning light this light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage...

  • Page 350

    • rear axle lock indicator — if equipped this light indicates when the rear axle lock has been activated. • low coolant level indicator this telltale will turn on to indicate the vehicle coolant level is low. • windshield washer fluid low indicator this telltale will turn on to indicate the wind- sh...

  • Page 351

    • lanesense service — if equipped this telltale will turn on to indicate that the lane sense departure has detected a failure. • loose fuel filler cap message indicator this telltale will turn on to indicate the fuel filler cap is loose. 13. Odometer display / fuel gauge / temperature gauge / submen...

  • Page 352

    • temperature gauge the temperature gauge shows engine coolant tem- perature. Any reading within the normal range indi- cates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tem- perature when driving in hot weather, up mountain grades, or ...

  • Page 353

    14. Red reconfigurable telltale display • engine temperature warning light this light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches h, this indicator will illuminate and a single chime will sound after reaching a set threshold. If the light turns on while...

  • Page 354

    Note: • even if power steering assistance is no longer opera- tional, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. • if the condition persists, see your a...

  • Page 355

    If jump starting is required, refer to “jump starting procedures” in “what to do in emergencies”. • electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. The light will come on when the ignition is first turned on and remain on...

  • Page 356

    Unless reset, this message will continue to display each time you turn the ignition switch to the on/run position or cycle the ignition to the on/run position if equipped with keyless enter-n-go™. To turn off the message temporarily, press and release the menu but- ton. To reset the oil change indic...

  • Page 357

    Spress the adaptive cruise control (acc) on/ off button (located on the steering wheel) until one of the following displays in the evic: adaptive cruise control off when acc is deactivated, the display will read “adap- tive cruise control off.” adaptive cruise control ready when acc is activated but...

  • Page 358

    • passenger seatbelt unbuckled • service airbag system • traction control off • washer fluid low • oil pressure low • oil change due • fuel low • service antilock brake system • service electronic throttle control • service power steering • cruise off • cruise ready • cruise set to xxx mph • tire pr...

  • Page 359

    • key in ignition • key in ignition lights on • remote start active key to run • remote start active push start button • remote start aborted fuel low • remote start aborted too cold • remote start aborted door open • remote start aborted hood open • remote start aborted tailgate open • remote start...

  • Page 360

    • transmission cool ready to drive • service transmission • service shifter • engage park brake to prevent rolling • transmission too cold idle with engine on • washer fluid low the reconfigurable telltales section is divided into the white telltales area on the right, amber telltales in the middle,...

  • Page 361

    Transmission temperature – automatic transmission only oil temp coolant temperature oil life battery voltage tire pressure press and release the up or down arrow button until “tire pressure” is highlighted in the evic. Press and release the right arrow button and one of the following will be display...

  • Page 362

    Fuel economy press and release the up or down arrow button until the fuel economy icon is highlighted. • average fuel economy/miles per gallon (mpg or l/100 km with bargraph) • range to empty (rte) • current miles per gallon (mpg) trip info press and release the up or down arrow button until the tri...

  • Page 363

    Screen setup press and release the up or down arrow button until the screen setup display icon is highlighted in the evic. Press and release the ok button to enter the sub-menus. The screen setup feature allows you to change what information is displayed in the instrument cluster as well as the loca...

  • Page 364

    Upper right • none • compass (default setting) • outside temp • oil temp • time • range to empty (rte) • average mpg • current mpg • trip a • trip b restore to defaults (restores all settings to default settings) • cancel • okay center • none • compass • outside temp. • time • range to empty • avera...

  • Page 365

    • trip b • audio information • menu title (default setting) uconnect® settings the uconnect® system uses a combination of soft and hard keys located on the center of the instrument panel that allows you to access and change the customer programmable features. Uconnect® 5.0 soft-keys and hard-keys 1 ...

  • Page 366

    Hard-keys hard-keys are located below the uconnect® system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side of the climate controls in the center of the instrument panel. Turn the control knob to scroll through menus and change settin...

  • Page 367

    Soft-keys soft-keys are accessible on the uconnect® display. Customer programmable features — uconnect® 5.0/8.4 settings press the apps soft-key, then press the settings soft-key to display the menu setting screen. In this mode the uconnect® system allows you to access programmable features that may...

  • Page 368

    • display brightness with headlights on when in this display, you may select the brightness with the headlights on. Adjust the brightness with the + and – setting soft-keys or by selecting any point on the scale between the + and – soft-keys. Then touch the arrow back soft-key. • display brightness ...

  • Page 369

    • touchscreen beep when in this display, you may turn on or shut off the sound heard when a touch screen button (soft-key) is pressed. Touch the touchscreen beep soft-key until a check-mark appears next to the setting, showing that setting has been selected. Touch the back arrow soft-key to return t...

  • Page 370

    • set time minutes when in this display, you may adjust the minutes. The sync with gps time soft-key must be unchecked. To make your selection, touch the + or - soft-keys to adjust the minutes up or down. Touch the back arrow soft-key to return to the previous menu or touch the x soft-key to close o...

  • Page 371

    • forward collision warning (fcw) active braking — if equipped the fcw system includes advanced brake assist (aba). When this feature is selected, it will apply the brakes to slow your vehicle in case of potential forward collision. The aba applies additional brake pressure when the driver requests ...

  • Page 372

    • parksense® active park assist — if equipped the rear park assist system will scan for objects behind the vehicle when the transmission shift lever is in re- verse and the vehicle speed is less than 11 mph (18 km/h). The system can be enabled with sound only, or sound and display. To change the par...

  • Page 373

    Refer to “parksense® rear park assist” in “understand- ing the features of your vehicle” for system function and operating information. • tilt mirrors in reverse — if equipped when this feature is selected, the outside sideview mir- rors will tilt downward when the ignition is in the run position an...

  • Page 374

    Image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed on the radio touchscreen display along with a caution note to “check entire surroundings” across the top of the screen. After five seconds, this note will disappear. The parkview®...

  • Page 375

    Setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. • electric park brake service mode this feature provides a means for a technician or vehicle owner to utilize a vehicle integrated, menu driven sys- tem, to command the electric park brake ...

  • Page 376

    The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, touch the headlights with wipers soft- key, until a check-mark appears next to setting, indicating that the setting has been selected. Touch the back arrow soft-key to ret...

  • Page 377

    • flash headlights with lock when this feature is selected, the headlights will flash when the doors are locked or unlocked with the remote keyless entry (rke) transmitter. This feature may be selected with or without the sound horn on lock feature selected. To make your selection, touch the flash h...

  • Page 378

    • sound horn with remote start when this feature is selected, the horn will sound when the remote start is activated. To make your selection, touch the sound horn with remote start soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft...

  • Page 379

    Return to the previous menu. Refer to “keyless enter-n- go™” in “things to know before starting your vehicle”. • memory to fob — if equipped this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection, touch the mem...

  • Page 380

    Seats soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. Engine off options after pressing the engine off options soft-key the fol- lowing settings will be available. • engine off power delay whe...

  • Page 381

    Note: keep magnetic materials away from the top of the instrument panel, such as ipod’s, mobile phones, laptop computers and radar detectors. This is where the com- pass module is located, and it can cause interference with the compass sensor, and it may give false readings. • perform compass calibr...

  • Page 382

    • equalizer when in this display you may adjust the bass, mid and treble settings. Adjust the settings with the + and – setting soft-keys or by selecting any point on the scale between the + and – soft-keys. Then touch the arrow back soft-key. Note: bass/mid/treble allow you to simply slide your fin...

  • Page 383

    Radio setup after pressing the radio setup soft-key the following settings will be available. • traffic announcement when this feature is selected it allows the system to pause receivers and media to issue a traffic bulletin. To change the traffic announcement setting touch the off or on soft-key. A...

  • Page 384

    Clear personal data after pressing the clear personal data settings soft-key the following settings will be available: • clear personal data when this feature is selected it will remove personal data including bluetooth® devices and presets. To clear per- sonal data touch the yes or no soft-key. A c...

  • Page 385

    Located in the front storage area, this feature allows an ipod® or external usb device to be plugged into the usb port. Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versions may not fully support the ipod® control features. Please visit apple’s webs...

  • Page 386

    Pressing the center button will make the radio switch between the various modes available (am/fm/sxm/ cd/aux, etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The following des...

  • Page 387

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 388

    Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. This system can be operated through either the controls on the instrument panel or through the uconnect® system dis- play. When the uconnect® system is in different modes (ra- dio, p...

  • Page 389

    Front blower control there are seven blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position. Note: for vehicles equipped with remote start, the climate controls...

  • Page 390

    Max a/c for maximum cooling, when max a/c is selected the a/c is turned on automatically and the air is recirculated. Note: a/c cannot be deselected when in max a/c position. The led will blink three times if the a/c button is pushed. If your air conditioning performance seems lower than expected, c...

  • Page 391

    Bi-level mode air is directed through the panel and floor outlets. Note: there is a difference in temperature (in any conditions other than full cold or full hot), between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort dur...

  • Page 392

    Recirculation control press this button to choose between outside air intake or recirculation of the air inside the vehicle. A led will illuminate when you are in recirculation mode. Only use the recirculation mode to temporarily block out any outside odors, smoke, or dust, and to cool the interior ...

  • Page 393

    Economy mode if economy mode is desired, press the a/c button to turn off the led indicator and the a/c compressor. Rotate the temperature control knob to the desired tem- perature. Also, make sure to select only panel, bi-level or floor modes. Stop/start system – if equipped while in an autostop, t...

  • Page 394

    Soft-keys soft-keys are accessible on the uconnect® system screen. Uconnect® 5.0 manual temperature controls — soft-keys uconnect® 8.4 manual temperature controls — soft-keys 392 understanding your instrument panel.

  • Page 395

    Button descriptions (applies to both hard-keys and soft-keys) 1. Max a/c button press and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manual mode and the max a/c indicator will tur...

  • Page 396

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 397

    7. Modes the airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, demist outlets and defrost outlets. The mode settings are as follows: • panel mode air comes from the outlets in the instrument panel. Each of these outlets can be individually adjus...

  • Page 398

    Note: the air conditioning compressor operates in mix and defrost modes even if the a/c button is not pressed. This dehumidifies the air to help dry the wind- shield. To improve fuel economy, use these modes only when necessary. 8. Climate control off button press and release this button to turn the...

  • Page 399

    Automatic climate controls with touch-screen — if equipped hard-keys the hard-keys located below the uconnect® screen. Soft-keys soft-keys are accessible on the uconnect® system screen. Uconnect® automatic climate controls — hard-keys uconnect® 8.4 automatic temperature controls — soft-keys 4 unders...

  • Page 400

    Button descriptions (applies to both hard-keys and soft-keys) 1. Max a/c button press and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manual mode and the max a/c indicator will tur...

  • Page 401

    6. Rear defrost button press and release this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 10 minutes. For each additional press of ...

  • Page 402

    8. Passenger temperature control down button provides the passenger with independent temperature control. Push the hard-key button for cooler temperature settings or on the touch-screen, press and slide the soft-key temperature bar towards the blue arrow soft-key for cooler temperature settings. Not...

  • Page 403

    11. Modes the airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, demist outlets and defrost outlets. The mode settings are as follows: • panel mode air comes from the outlets in the instrument panel. Each of these outlets can be individually adju...

  • Page 404

    12. Climate control off button press and release this button to turn the climate control on/off. 13. Driver temperature control down button provides the driver with independent temperature con- trol. Push the hard-key button for cooler temperature settings or on the touch-screen, press and slide the...

  • Page 405

    Note: • if fog or mist appears on the windshield or side glass, select defrost mode and increase blower speed. • if your air conditioning performance seems lower than expected, check the front of the a/c condenser (lo- cated in front of the radiator), for an accumulation of dirt or insects. Clean wi...

  • Page 406

    Note: in cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (soft button greyed out) if conditions exist that could create fogging on the inside of the windshield. On systems with manual climate con- trols, the recirculation mod...

  • Page 407

    Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode, and blower speed to provide comfort as quickly as possible. • the temperature can be displayed in u.S. Or metric units by selecting the uconnect® customer- p...

  • Page 408

    Operating tips note: refer to the chart at the end of this section for suggested control settings for various weather condi- tions. Summer operation the engine cooling system must be protected with a high-quality antifreeze coolant to provide proper corro- sion protection and to protect against engi...

  • Page 409

    Note: • recirculate without a/c should not be used for long periods, as fogging may occur. • automatic temperature controls (atc) will automati- cally adjust the climate control settings to reduce or eliminate window fogging on the front windshield. When this occurs, recirculation will be unavailabl...

  • Page 410

    Control setting suggestions for various weather conditions 408 understanding your instrument panel.

  • Page 411: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .414 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .414 ▫ extreme cold weather (below –20°f or −29°c) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .415 ▫ extended park starting. . . . . . . ...

  • Page 412

    ▫ srear electronic locker (e-locker) system – if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .436 䡵 selec-terrain™ . . . . . . . . . . . . . . . . . . . . .437 ▫ description . . . . . . . . . . . . . . . . . . . . . . . . . .437 䡵 on-road driving tips . . . . . . . . . . . . . . . ....

  • Page 413

    ▫ electronic stability control (esc) . . . . . . . . . .466 ▫ esc activation/malfunction indicator light and esc off indicator light . . . . . . . . . . . . . . . .470 ▫ trailer sway control (tsc) . . . . . . . . . . . . . . .471 ▫ ready alert braking (rab). . . . . . . . . . . . . . .472 ▫ rain bra...

  • Page 414

    䡵 tire pressure monitor system (tpms) . .500 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . .503 ▫ premium system – if equipped. . . . . . . . . . . .506 ▫ general information . . . . . . . . . . . . . . . . . . .511 䡵 fuel requirements . . . . . . . . . . . . . . . . . .511 ▫ reformu...

  • Page 415

    ▫ towing this vehicle behind another vehicle . .534 ▫ recreational towing — front-wheel drive (fwd) models . . . . . . . . . . . . . . . . . . . . . . . . . . . . .535 ▫ recreational towing — 4wd models with 1-speed power transfer unit. . . . . . . . . . . . . . . . . . . .536 ▫ recreational towing ...

  • Page 416

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or with access to...

  • Page 417

    Within 10 seconds, turn the ignition switch to the lock position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Tip start feature turn the ignition switch to start position and release it as soon as the starter engages. The starter motor will continue to run, but will automatic...

  • Page 418

    If engine fails to start warning! • never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. • do not attempt to push or tow your vehicle to get it started. Vehicles equippe...

  • Page 419

    Switch to the lock position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Caution! To prevent damage to the starter, wait 10 to 15 seconds before trying again. After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Engine block h...

  • Page 420

    Caution! (continued) • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle speed. • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting into any gear, make sure your foot is firmly pressi...

  • Page 421

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 422

    Brake/transmission shift interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the shift lever in park unless the brakes are applied. To shift the transmission out of park, the ignition switch must be turned to the on/run position (engine runnin...

  • Page 423

    Operation ⬙ in this section for further information). Mov- ing the shift lever into the ers (-/+) position (beside the drive position) displays the current gear in the instru- ment cluster, and prevents automatic upshifts beyond this gear. In ers mode, toggling the shift lever forward (-) or rearwar...

  • Page 424

    When parking on a hill, apply the parking brake before shifting the transmission to park, otherwise the load on the transmission locking mechanism may make it diffi- cult to move the shift lever out of park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away f...

  • Page 425

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 426

    Caution! • before moving the shift lever out of park, you must place the ignition from the lock/off posi- tion to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear rang...

  • Page 427

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 428

    If the transmission operating temperature exceeds nor- mal operating limits, the transmission controller may modify the transmission shift schedule, reduce engine torque, and/or expand the range of torque converter clutch engagement. This is done to prevent transmission damage due to overheating. If...

  • Page 429

    To operate. The malfunction indicator light (mil) may be illuminated. Limp home mode allows the vehicle to be driven to an authorized dealer for service without dam- aging the transmission. In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing t...

  • Page 430

    Moving the shift lever to the ers position (beside drive) will activate ers mode, display the current gear in the instrument cluster, and maintain that gear as the top available gear. Once in ers mode, moving the shift lever forward (-) or rearward (+) will change the top available gear. To exit ers...

  • Page 431

    Additionally, on dry pavement under heavy throttle input (where one may have no wheel spin), torque will be sent to the rear in a pre-emptive effort to improve vehicle launch and performance characteristics. Caution! All wheels must have the same size and type tires. Unequal tire sizes must not be u...

  • Page 432

    2–speed four-wheel drive (4wd) — if equipped the four-wheel drive is fully automatic in the normal driving mode. The selec-terrain buttons provide three selectable mode positions: • 4wd low • rear lock (if equipped) • neutral 2–speed 4wd switch selec-terrain switch 430 starting and operating.

  • Page 433

    When additional traction is required, the 4wd low range position can be used to provide an additional gear reduction which allows for increased torque to be deliv- ered to both the front and rear wheels. 4wd low is intended for loose, slippery road surfaces only. Driving in 4wd low on dry, hard-surf...

  • Page 434

    Warning! You or others could be injured if you leave the vehicle unattended with the power transfer unit in the neutral (n) position without first fully engag- ing the parking brake. The neutral (n) position disengages both the front and rear drive shafts from the powertrain and will allow the vehic...

  • Page 435

    Note: if shift conditions/interlocks are not met a mes- sage will flash from the electronic vehicle information center (evic) with instructions on how to complete the requested shift. Refer to “electronic vehicle information center (evic)” in “understanding your instrument panel” for further informa...

  • Page 436

    • shifting into or out of 4wd low is possible with the vehicle completely stopped; however, difficulty may occur due to the mating clutch teeth not being prop- erly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur. The preferred method is with the ve...

  • Page 437

    6. Using a ballpoint pen or similar object, press and hold the recessed power transfer unit neutral (n) button (lo- cated above the selector switch) for four seconds. The light behind the neutral (n) symbol will blink, indi- cating shift in progress. The light will stop blinking (stay on solid) when...

  • Page 438

    Rear electronic locker (e-locker) system – if equipped the rear e-locker system features a mechanical locking rear differential to provide better traction in the 4wd low position. The “rear lock” button is on the selec-terrain knob. Activating the rear e-locker to activate the rear e-locker system, ...

  • Page 439

    • when disengaging rear e-locker, the indicator lights in the instrument cluster and on the rear lock button will begin to flash. When the shift is complete the rear lock indicator lights will remain off. • shifting into or out of rear e-locker is possible with the vehicle completely stopped; howeve...

  • Page 440

    Selec-terrain™ offers the following modes: • auto – fully automatic full time four-wheel drive operation can be used on and off road. Balances traction with seamless steering feel to provide im- proved handling and acceleration over two-wheel drive vehicles. • snow – tuning set for additional stabil...

  • Page 441

    • rock – off-road calibration only available in 4wd low range. Traction based tuning with improved steer-ability for use on high traction off-road surfaces. Use for low speed obstacles such as large rocks, deep ruts, etc. Note: rock mode is only available on the vehicles equipped with the off-road p...

  • Page 442

    Off-road driving tips when to use 4wd low range when off-road driving, shift to 4wd low for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low-speed pulling power (refer to “all wheel drive and four-wheel drive operation” in thi...

  • Page 443

    Flowing water if the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced. If you must cross flowing-water, avoid depths in excess of 9 inches (22 cm). The flowing water can erode the streambed causing your vehicle to si...

  • Page 444

    Avoid abrupt downshifts on icy or slippery roads be- cause engine braking may cause skidding and loss of control. Hill climbing note: before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gea...

  • Page 445

    Traction downhill shift the transmission into a low gear and the 4wd system to 4wd low range or select hill descent control if equipped (refer to ⬙ electronic brake control system ⬙ in this section for further information. Let the vehicle go slowly down the hill with all four wheels turning against ...

  • Page 446

    Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent a collision. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if y...

  • Page 447

    Note: • even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at low speeds and during parking maneuvers. • if the condition persists, see your authorized d...

  • Page 448

    To apply the parking brake manually, pull up on the switch momentarily. You may hear a slight whirring sound from the back of the vehicle while the parking brake engages. Once the parking brake is fully engaged, the brake warning lamp in the instrument cluster and an indicator on the switch will ill...

  • Page 449

    To release the park brake manually, the ignition switch must be on. Put your foot on the brake pedal, then push the parking brake switch down momentarily. You may hear a slight whirring sound from the back of the car while the parking brake disengages. You may also notice a small amount of movement ...

  • Page 450

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave a vehicle equipped with keyless enter-n- go™ in the acc or on/run mode. A child could operate power windows, other controls, or move the vehicle. • be sure the parking br...

  • Page 451

    Reaches approximately 3 mph, the parking brake will remain engaged. Warning! Driving the vehicle with the parking brake engaged, or repeated use of the parking brake to slow the vehicle may cause serious damage to the brake sys- tem. In the unlikely event of a malfunction of the electric park brake ...

  • Page 452

    Safehold can be temporarily bypassed by pressing the electric park brake switch while the driver door is open. Once manually bypassed, safehold will be enabled again once the vehicle reaches 12 mph (20 km/h) or the ignition is turned to the off position and back to on again. Brake service mode we re...

  • Page 453

    Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. Anti-lock brake system the anti-...

  • Page 454

    Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the abs cannot prevent the natural laws of phys- ics from acting on the ve...

  • Page 455

    • engines may idle at higher speeds during warm-up, which could cause rear wheels to spin and result in loss of vehicle control. Be especially careful while driving on slippery roads, in close-quarter maneuver- ing, parking, or stopping. • do not drive too fast for road conditions, especially when r...

  • Page 456

    Anti-lock brake system (abs) this system aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lock-up to help avoid skidding on slippery surfaces during braking. Refer to “anti-lock brake system” in “starting a...

  • Page 457

    Or the “full off” mode. Refer to “electronic stability control (esc)” in this section for further information. Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing...

  • Page 458

    Applies the appropriate brake and may also reduce engine power to lessen the chance that wheel lift will occur. Erm will only intervene during very severe or evasive driving maneuvers. Erm can only reduce the chance of wheel lift occurring during severe or evasive driving maneuvers. It cannot preven...

  • Page 459

    The following conditions must be met in order for hsa to activate: • the vehicle must be stopped. • the vehicle must be on a 7% (approximate) grade or greater hill. • the gear selection must match vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle backing uphill is in ...

  • Page 460

    Towing with hsa hsa will provide assistance during acceleration on an incline while towing a trailer. Warning! • if you use a trailer brake controller with your trailer, the trailer brakes may be activated and deactivated with the brake switch. If so, there may not be enough brake pressure to hold b...

  • Page 461

    Hill descent control (hdc) — if equipped hdc is intended for low speed off road driving while in 4wd low range. Hdc maintains vehicle speed while descending hills during various driving situations. Hdc controls vehicle speed by actively controlling the brakes. Hdc has three states: 1. Off (feature i...

  • Page 462

    Activating hdc once hdc is enabled it will activate automatically if driven down a grade of sufficient magnitude (greater than approximately 8%). The set speed for hdc is selectable by the driver, and can be adjusted by using the gear shift lever. The following summarizes the hdc set speeds: • p = n...

  • Page 463

    Deactivating hdc hdc will be deactivated but remain available if any of the following conditions occur: • driver overrides hdc set speed with throttle or brake application. • vehicle speed exceeds 20 mph but remains below 40 mph. • vehicle is on a downhill grade of insufficient magni- tude (less tha...

  • Page 464

    • the cluster icon and switch lamp will flash for several seconds then extinguish when the driver presses the hdc switch but enable conditions are not met. • the cluster icon and switch lamp will flash for several seconds then extinguish when hdc deactivates due to excess speed. • the cluster icon a...

  • Page 465

    Enabling ssc ssc is enabled by pressing the ssc switch, but the following conditions must also be met to enable ssc: • driveline is in 4wd low range • vehicle speed is below 5 mph • parking brake is released • driver door is closed • driver is not applying throttle activating ssc once ssc is enabled...

  • Page 466

    • 7th= 4.3 mph (7 km/h) • 8th = 5 mph (8 km/h) • 9th = 5.6 mph (9 km/h) • reverse = .6 mph (1 km/h) • neutral = 1.2 mph (2 km/h) • park = ssc remains enabled but not active note: these ssc default set speeds are dependent on hill grade. That is the steeper the grade of the hill the vehicle travels o...

  • Page 467

    Deactivating ssc ssc will be deactivated but remain available if any of the following conditions occur: • driver overrides ssc set speed with throttle or brake application. • vehicle speed exceeds 20 mph but remains below 40 mph. • vehicle is shifted to park. Disabling ssc ssc will deactivate and be...

  • Page 468

    • the cluster icon and switch lamp will flash for several seconds then extinguish when the driver presses the ssc switch but enable conditions are not met. • the cluster icon and switch lamp will flash for several seconds then extinguish when ssc deactivates due to excess speed. • the cluster icon a...

  • Page 469

    The “esc activation/malfunction indicator light” lo- cated in the instrument cluster will start to flash as soon as the tires lose traction and the esc system becomes active. The “esc activation/malfunction indicator light” also flashes when the tcs is active. If the “esc activation/malfunction indi...

  • Page 470

    Esc on – two-wheel drive vehicles and four-wheel drive vehicles in 2wd and 4wd high range this is the normal operating mode for esc when oper- ating a two-wheel drive vehicle. It is also the normal mode for operating a four-wheel drive vehicle in 2wd or 4wd high range. The esc system will be in “esc...

  • Page 471

    Warning! • when in “partial off” mode, the tcs functionality of esc, (except for the limited slip feature de- scribed in the tcs section), has been disabled and the “esc off indicator light” will be illuminated. When in “partial off” mode, the engine power reduction feature of tcs is disabled, and t...

  • Page 472

    Note: • “full off” is the only operating mode for esc in 4wd low range. The esc system will be in this mode whenever the vehicle is started in 4wd low range or the power transfer unit is shifted into 4wd low range. • the “esc off” message will display and a chime will sound when the shift lever is m...

  • Page 473

    Speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected. The “esc activation/malfunction indicator light” (lo- cated in the instrument cluster) starts to flash as soon as the tires lose traction and the esc system becomes act...

  • Page 474

    Appropriate wheel(s) to counteract the sway of the trailer. Tsc will become active automatically once an excessively swaying trailer is recognized. Always use caution when towing a trailer and follow the trailer tongue weight recommendations. When tsc is functioning, the “esc activation/malfunction ...

  • Page 475

    Rain brake support (rbs) rain brake support may improve braking performance in wet conditions. It will periodically apply a small amount of brake pressure to remove any water buildup on the front brake rotors. It is triggered by the windshield wiper setting and only functions when they are in use. W...

  • Page 476

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 477

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 478

    Example: 10.5 = section width in inches (in) r = construction code — ⬙ r ⬙ means radial construction — ⬙ d ⬙ means diagonal or bias construction 15 = rim diameter in inches (in) service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol...

  • Page 479

    Example: load identification: ⴖ ....Blank.... ⴖ = absence of any text on the sidewall of the tire indicates a standard load (sl) tire extra load (xl) = extra load (or reinforced) tire light load (ll) = light load tire c, d, e, f, g = load range associated with the maximum load a tire can carry at a ...

  • Page 480

    Example: dot ma l9 abcd 0301 dot = department of transportation — this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 481

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 482

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. B-pillar location for tire and loading information placard 480 starting and operating.

  • Page 483

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the ve- hicle. 2) total weight your vehicle can carry. 3) tire size designed for your vehicle. 4) cold tire inflation pressures for the front, rear, and spare tires...

  • Page 484

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 485

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 486

    484 starting and operating.

  • Page 487

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 488

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear pat- terns...

  • Page 489

    • inspect tires for signs of tire wear or visible damage. Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard...

  • Page 490

    Loading may be required for high-speed vehicle opera- tion. Refer to your authorized tire dealer or original equipment vehicle dealer for recommended safe operat- ing speeds, loading and cold tire inflation pressures. Warning! High speed driving with your vehicle under maxi- mum load is dangerous. T...

  • Page 491

    • the puncture is no greater than ¼ ⬙ (6 mm). Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service de...

  • Page 492

    If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Snow tires generally have lower speed ratings than what was originally equipped with y...

  • Page 493

    Spare tires – if equipped note: for vehicles equipped with tirefit instead of a spare tire, please refer to “tirefit kit” in “what to do in emergencies” for further information. Caution! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a compact, f...

  • Page 494

    Wheel is designed specifically for the compact spare tire. Do not install more than one compact spare tire and wheel on the vehicle at any given time. Warning! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have l...

  • Page 495

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your tire and loading inf...

  • Page 496

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further infor- mation. Life of t...

  • Page 497

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 498

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 499

    • use on front tires only • due to limited clearance, the following traction de- vices are recommended: front wheel drive (fwd) models • original equipment 225/60r17 and 225/55r18 tire sizes are not chainable. • the use of 7mm snow chains is permitted with the use of 215/60r17 tires on size 17 x 7.0...

  • Page 500

    Caution! (continued) • damage to four wheel drive (4wd) trailhawk models may result if tire chains or traction devices are used with original equipment size tires. Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could los...

  • Page 501

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation ...

  • Page 502

    Caution! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause (continued) caution! (continued) damage to the power transfer unit. Tire rotation schedule should be followed to balance tire wear. Tir...

  • Page 503

    In “starting and operating” for information on how to properly inflate the vehicle’s tires. The tire pressure will also increase as the vehicle is driven. This is normal and there should be no adjustment for this increased pres- sure. The tpms will warn the driver of a low tire pressure if the tire ...

  • Page 504

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, t...

  • Page 505

    • driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and i...

  • Page 506

    Tire pressure monitoring low pressure warnings the “tire pressure monitoring telltale light” will illuminate in the instrument cluster, a “low tire pressure” message will display in the instrument cluster, an ⬙ inflate to xx ⬙ message will be displayed and a chime will sound when tire pressure is lo...

  • Page 507

    4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with tpms sensors. Vehicles with full-size spare 1. The matching full-size spare wheel and tire assembly has a tire pressure monitoring sensor that can be monitored by the tpms. 2. If you install the matching full-size spare in ...

  • Page 508

    5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare, the tpms will update automatically and the “tpms telltale light” will turn off, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires...

  • Page 509

    Tire pressure monitoring low pressure warnings the “tire pressure monitoring telltale light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the electronic vehicle information center (evic) will dis...

  • Page 510

    Values in the graphic display in the evic will return to their original color, and the “tire pressure monitoring telltale light” will turn off. The vehicle may need to be driven for up to 20 minutes above 15.5 mph (25 km/h) in order for the tpms to receive this information. Service tpms warning when...

  • Page 511

    If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” will no longer flash, and the “service tpm system message will no longer display, and a pressure value will display i...

  • Page 512

    4. The evic will display a graphic showing the tire pressure value in the same color as the other pressure values in place of the different color low tire pressure value. The evic will also display a “spare low pressure” message to remind you to service the flat tire. Vehicles with compact spare 1. ...

  • Page 513

    Low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15.5 mph (25 km/h) in order for the tpms to receive this information. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. O...

  • Page 514

    Consistent gasoline specifications (the worldwide fuel charter, wwfc) which define fuel properties necessary to deliver enhanced emissions, performance, and dura- bility for your vehicle. The manufacturer recommends the use of gasoline that meet the wwfc specifications if they are available. 3.2l en...

  • Page 515

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Fuels blended with oxygenates may be used in your vehicle. Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in start...

  • Page 516

    • disconnect and reconnect the battery to reset the engine controller memory. More extensive repairs will be required for prolonged exposure to e-85 fuel. Mmt in gasoline mmt (methylcyclopentadienyl manganese tricarbonyl) is a manganese-containing metallic additive that is blended into some gasoline...

  • Page 517

    Caution! (continued) • an out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate ser- vice. Contact your authorized...

  • Page 518

    Warning! (continued) • guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Adding fuel the gas cap is located behind the fu...

  • Page 519

    2. Open the fuel filler door, and remove the fuel filler cap. Note: • in certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button. Do not pry on the door. •...

  • Page 520

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gaso...

  • Page 521

    Vehicle loading certification label as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle w...

  • Page 522

    Tire size the tire size on the vehicle certification label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim size this is the rim size that is appropriate for the tire size listed. Inflation pressure this is the cold tire inf...

  • Page 523

    Items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving. Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. Caution! Do not load your vehicle any heavier than the ...

  • Page 524

    Exceed the gvwr. Refer to “vehicle loading/vehicle certification label” in “starting and operating” for further information. Gross trailer weight (gtw) the gtw is the weight of the trailer plus the weight of all cargo, consumables, and equipment (permanent or tem- porary) loaded in or on the trailer...

  • Page 525

    Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision. Tongue weight (tw) the tongue weight is the downward force exerted on the hitch ball by t...

  • Page 526

    Weight-distributing hitch a weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s direc...

  • Page 527

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 528

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission model frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.4l/automatic 4x2 or 4x4 32 sq ft (2.97 sq...

  • Page 529

    Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to s...

  • Page 530

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “tire and loading information” placard for the maximum combine...

  • Page 531

    Warning! (continued) • when hauling cargo, or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance, or dam- age to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires. • safety chains must always be use...

  • Page 532

    • check the trailer tires for proper tire inflation pres- sures before trailer usage. • check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information” in “starting and operating” for the proper inspection procedure. • when replacing tires, refer t...

  • Page 533

    Warning! • do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have a collision. • towing any trailer will increase your stopping distance. When towing you should allow f...

  • Page 534

    Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground 2 — backup lamps 6 — left stop/turn 3 — right stop/turn 7 — running lamps 4 — electric brakes 532 starting and operating.

  • Page 535

    Towing tips before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Automatic transmission - if equipped the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting wh...

  • Page 536

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle 4wd models towing condition wheel off the ground front-wheel drive (fwd) models 1-speed power transfer unit 2-speed power transfer unit flat tow none not allowed not allowed see instructions: • transmission in pa...

  • Page 537

    Recreational towing — front-wheel drive (fwd) models automatic transmission - if equipped do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing of automatic transmission vehicles is allowed only if the front wheels are off the ground. This may be accomplished using ...

  • Page 538

    Caution! Towing this vehicle in violation of the above require- ments can cause severe engine and/or transmission damage. Damage from improper towing is not cov- ered under the new vehicle limited warranty. Recreational towing — 4wd models with 1-speed power transfer unit recreational towing is not ...

  • Page 539

    Caution! • do not dolly tow any 4wd vehicle. Internal damage to the transmission or power transfer unit will occur if a dolly is used when recreational towing. • tow only in a forward direction. Towing this ve- hicle backwards can cause severe damage to the power transfer unit. • the transmission mu...

  • Page 540

    Warning! (continued) position disengages both the front and rear drive- shafts from the powertrain and will allow the vehicle to move, even if the transmission is in park. The parking brake should always be applied when the driver is not in the vehicle. Use the following procedure to prepare your ve...

  • Page 541

    7. After the shift is completed and the neutral (n) light stays on, release the neutral (n) button. 8. Start the engine. 9. Shift the transmission into reverse. 10. Release the brake pedal for five seconds and ensure that there is no vehicle movement. 11. Shift the transmission to neutral. 12. Apply...

  • Page 542

    Note: • steps 1 through 5 are requirements that must be met prior to pressing the neutral (n) button, and must continue to be met until the shift has been completed. If any of these requirements are not met prior to pressing the neutral (n) button or are no longer met during the shift, then the neut...

  • Page 543

    6. Using a ballpoint pen or similar object, press and hold the recessed power transfer unit neutral (n) button (located by the selector switch) for one second. 7. When the neutral (n) indicator light turns off, release the neutral (n) button. 8. After the neutral (n) button has been released, the po...

  • Page 544

    13. Press and hold the brake pedal. 14. Release the parking brake. 15. Shift the transmission into drive, release the brake pedal, and check that the vehicle operates normally. Note: • steps 1 through 5 are requirements that must be met prior to pressing the neutral (n) button, and must continue to ...

  • Page 545: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .545 䡵 if your engine overheats . . . . . . . . . . . .545 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .546 ▫ torque specifications . . . . . . . . . . . . . . . . . .546 䡵 tirefit k...

  • Page 546

    䡵 towing a disabled vehicle . . . . . . . . . . .575 ▫ front-wheel drive (fwd) models . . . . . . . . .577 ▫ 4x4 models with 1–speed power transfer unit. . . . . . . . . . . . . . . . . . . . . . . . .578 ▫ 4x4 models with 2–speed power transfer unit. . . . . . . . . . . . . . . . . . . . . . . . .5...

  • Page 547

    Hazard warning flashers the hazard warning flasher switch is located in the switch bank below the radio screen. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Press t...

  • Page 548

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maximum he...

  • Page 549

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Wheel mounting surface torque patterns 6 what to do in emergencies 547.

  • Page 550

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Tirefit kit — if equipped small punctures up to 1/4 in (6 mm) in the tire tread can be sealed with tiref...

  • Page 551

    Tirefit kit components and operation 1. Sealant bottle 2. Deflation button 3. Pressure gauge 4. Power button 5. Mode select knob 6. Sealant hose (clear) 7. Air pump hose (black) 8. Power plug using the mode select knob and hoses your tirefit kit is equipped with the following symbols to indicate the...

  • Page 552

    Selecting sealant mode turn the mode select knob (5) to this position to inject the tirefit sealant and to inflate the tire. Use the sealant hose (clear hose) (6) when selecting this mode. Using the power button push and release the power button (4) once to turn on the tirefit kit. Push and release ...

  • Page 553

    • for optimum performance, make sure the valve stem on the wheel is free of debris before connecting the tirefit kit. • you can use the tirefit air pump to inflate bicycle tires. The kit also comes with two needles, located in the accessory storage compartment (on the bottom of the air pump) for inf...

  • Page 554

    Warning! (continued) • keep tirefit away from open flames or heat source. • a loose tirefit kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tirefit kit in the place provided. Failure to follow these warnings can result in injuries that are ...

  • Page 555

    Kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceed- ing. 3. Place the transmission in park (auto transmission) or in gear (manual transmission) and turn off the igni- tion. 4. Set the p...

  • Page 556

    Note: sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow within 0 – 10 seconds through the sealant hose (6): 1. Press the power button (4) to turn off the tirefit kit. Disconnect the sealant hose (6) from the valve stem. Make sure the valve stem is free...

  • Page 557

    If the tire does not inflate to at least 26 psi (1.8 bar) pressure within 15 minutes: • the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. Note: if the tire becomes over-inflated, press the defla- tion button to reduce the tire pressure to the recom- men...

  • Page 558

    (d) drive vehicle: immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure distribution of the tirefit sealant within the tire. Do not exceed 55 mph (88 km/h). Warning! Tirefit is not a permanent flat tire repair. Have the tire inspected a...

  • Page 559

    If the tire pressure is 19 psi (1.3 bar) or higher: 1. Press the power button (4) to turn on tirefit and inflate the tire to the pressure indicated on the tire and loading information label on the driver-side door opening. Note: if the tire becomes over-inflated, press the defla- tion button to redu...

  • Page 560

    5. Position the new sealant bottle (1) in the housing so that the sealant hose (6) aligns with the hose slot in the front of the housing. Press the bottle into the housing. An audible click will be heard indicating the bottle is locked into place. 6. Verify that the cap is installed on the fitting a...

  • Page 561

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack location/spare tire stowage the jack, wheel cho...

  • Page 562

    4. Remove the chocks. 5. Remove the scissors jack and wheel bolt wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the wheel bolt wrench, and remove the wrench from the jack assembly. Note: the jack handle attaches to the side of the jack with two attachment point...

  • Page 563

    Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Preparations for jacking 1. Park the vehicle o...

  • Page 564

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the ...

  • Page 565

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare tire, jack, and wheel bolt wrench. 2. If equipped with aluminum wheels where the center cap covers the wheel bolts, use the wheel bolt wre...

  • Page 566

    Jacking locations rear jacking location 564 what to do in emergencies.

  • Page 567

    Rear jacking engagement point front jacking location 6 what to do in emergencies 565.

  • Page 568

    5. Raise the vehicle just enough to remove the flat tire. Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire. 7. Remove the alig...

  • Page 569

    Note: • for vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. • refer to “compact spare tire” and to “limited-use spare” under “tires—general information” in “starting and operating” for additional warnings, cautions, and information about the spare ti...

  • Page 570

    10. Lower the vehicle to the ground by turning the jack handle counterclockwise. 11. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the wheel bolts in a star pattern until each wheel bolt has been tightened twice. Refer to “t...

  • Page 571

    Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Road tire installation 1. Mount the road tire ...

  • Page 572

    5. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel bolts are properly seated against the wheel. Jump-starting procedures if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or ...

  • Page 573

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 574

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper c...

  • Page 575

    8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle. If frequent jump-starting is required to start your vehicle you should have ...

  • Page 576

    Use the least amount of accelerator pedal pressure that will maintain the rocking motion without spinning the wheels or racing the engine. Note: press the ⬙ esc off ⬙ switch (if necessary), to place the electronic stability control (esc) system in ⬙ partial off ⬙ mode, before rocking the vehicle. Re...

  • Page 577

    Warning! (continued) even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping when you are stuck and do not let anyone near a spinning wheel, no matter ...

  • Page 578

    4x4 models towing condition wheels off the ground fwd mod- els 1–speed power transfer unit 2–speed power transfer unit flat tow none not al- lowed not allowed see instructions under “recreational towing” in “starting and operating” • transmission in park • power transfer unit in neutral • tow in for...

  • Page 579

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 580

    Caution! Towing this vehicle in violation of the above require- ments can cause severe transmission damage. Dam- age from improper towing is not covered under the new vehicle limited warranty. 4x4 models with 1–speed power transfer unit the manufacturer requires towing with all four wheels off the g...

  • Page 581

    4x4 models with 2–speed power transfer unit the manufacturer recommends towing with all four wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly. If flatbed equipment is not available and the power...

  • Page 583: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 2.4l . . . . . . . . . .583 䡵 engine compartment — 3.2l . . . . . . . . . .584 䡵 onboard diagnostic system — obd ii . .585 ▫ loose fuel filler cap message . . . . . . . . . . . .586 䡵 emissions inspection and maintenance programs . . . . . . ....

  • Page 584

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . .609 ▫ automatic transmission . . . . . . . . . . . . . . . .611 ▫ sky slider™ top care . . . . . . . . . . . . . . . . . .613 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .615 䡵 fuses...

  • Page 585

    Engine compartment — 2.4l 1 — air cleaner filter 5 — power distribution center (fuses) 2 — engine coolant pressure cap 6 — battery 3 — oil fill cap 7 — washer fluid reservoir 4 — brake fluid reservoir 8 — engine oil dipstick 7 maintaining your vehicle 583.

  • Page 586

    Engine compartment — 3.2l 1 — engine coolant reservoir 5 — washer fluid reservoir 2 — engine oil filter access cover 6 — battery 3 — brake fluid reservoir 7 — engine oil fill 4 — power distribution center (fuses) 8 — air cleaner filter 584 maintaining your vehicle.

  • Page 587

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 588

    Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gascap” message will display in the odometer or a “check gascap” message will be displayed in the electronic vehicle information center (evic). Refer to “...

  • Page 589

    Your vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. To check if your vehicle’s obd ii system is ready, you must do the following: 1. Cycle the ignition switch to the on position, but do not crank or start the engine. Note: if you crank or start...

  • Page 590

    Replacement parts use of genuine mopar® parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by the use of non-mopar® parts for mainte- nance and repairs will not be covered by the new vehicle limited warranty. Deale...

  • Page 591

    Maintenance procedures the pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed “maintenance schedule”, there are other components which may require servicing or replacement in the fu...

  • Page 592

    Regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Always maintain the oil level within th...

  • Page 593

    American petroleum institute (api) engine oil identification symbol this symbol means that the oil has been certified by the american petroleum institute (api). The manufacturer only recommends api certified engine oils. Caution! Do not use chemical flushes in your engine oil as the chemicals can da...

  • Page 594

    Engine oil viscosity (sae grade) – 3.2l engine mopar® sae 5w-20 engine oil or equivalent pennzoil® or shell helix® is recommended for all operating tem- peratures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine ...

  • Page 595

    Note: for best access to the oil filter, a drive on hoist should be used instead of a chassis hoist. Engine oil filter selection this manufacturer’s engines have a full-flow type dispos- able oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerabl...

  • Page 596

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 597

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 598

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 599

    However, the manufacturer recommends that air condi- tioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment. Note: use only manufacturer approved a/c system pag compressor oil, and refrigerants. A/c air filter – if equipped refer to the “...

  • Page 600

    Windshield wiper blades clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the w...

  • Page 601

    Note: the rear wiper arm cannot be raised fully up- ward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. ...

  • Page 602

    5. Lower the wiper blade and snap the pivot cap into place. Adding washer fluid the windshield and rear window washers share the same fluid reservoir. The fluid reservoir is located in the front of the engine compartment. Be sure to check the fluid level in the reservoir at regular intervals. Fill t...

  • Page 603

    Have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, have the exhaust system inspected e...

  • Page 604

    Caution! (continued) • damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of ...

  • Page 605

    • do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions. Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam f...

  • Page 606

    With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of engine coolant (antifreeze) from the radiator drain cock. If the cap is sealing properly, the engine coolant (anti- freeze) will begin to d...

  • Page 607

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 608

    The same engine coolant (oat coolant conforming to ms-12106) throughout the life of your vehicle. Please review these recommendations for using organic additive technology (oat) engine coolant (antifreeze) that meets the requirements of chrysler material stan- dard ms-12106. When adding engine coola...

  • Page 609

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery tank. The cap should be inspected and cleaned if there is any accumulation of foreign mater...

  • Page 610

    Disposal of used engine coolant used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol...

  • Page 611

    If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • do not overfill the coolant expansion bottle. • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine c...

  • Page 612

    Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency...

  • Page 613

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 614

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Refer to “fluids, lubricants, and genuine parts” in this section for fluid specifications. Special additives the manufacturer s...

  • Page 615

    Caution! If a transmission fluid leak occurs, visit your autho- rized dealer immediately. Severe transmission dam- age may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid and filter changes under normal operating conditions, the fluid installed at the f...

  • Page 616

    General cleaning careful vacuuming of the top before washing is helpful in removing dust and other foreign particles. If hand washing: • wash in partial shade instead of direct sun. • wet the entire vehicle before washing the top. • wash the top with a soft, natural bristle scrub brush, and a mild s...

  • Page 617

    Additional cleaning procedure for additional cleaning assistance in removing stubborn stains, apply mopar® convertible cloth top cleaner or equivalent to the complete stain, extending 2 inches (50 mm) beyond the stain. With a soft bristle brush, scrub in all directions over the stain. Avoid heavy sc...

  • Page 618

    Road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance bui...

  • Page 619

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty r...

  • Page 620

    Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • to remove heavy soil and/or excessive brake dust, use mopar® wheel cleaner. Note: if your vehicle is equipped with dark ...

  • Page 621

    • for tough stains, apply mopar® total clean, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar® multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap resid...

  • Page 622

    Solvents, detergents, or ammonia-based cleaners to clean leather upholstery. Application of a leather conditioner is not required to maintain the original condition. Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may caus...

  • Page 623

    When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be...

  • Page 624

    Warning! (continued) • before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged. Warning! If the replaced fuse blows again, contact an autho- rized dealer. Warning! If a general protection fuse for safety systems (air bag system, ...

  • Page 625

    Cavity blade fuse cartridge fuse description f06 — — not used f07 15 amp blue — powertrain control module - pcm f08 25 amp clear — engine control module (ecm) f09 — — not used f10 20 amp yellow — power takeoff unit (ptu) f11 — — not used f12 20 amp yellow — brake vacuum pump - if equipped f13 10 amp...

  • Page 626

    Cavity blade fuse cartridge fuse description f21 — — not used f22 5 amp tan — radiator fan f23 70 amp tan — body controller module (bcm) - feed 1 f24 — — not used f25 — — not used f26 — 30 amp pink fuel heater - diesel only f27 — — not used f28 15 amp blue — transmission con- trol module (tcm) f29 —...

  • Page 627

    Cavity blade fuse cartridge fuse description f38 — 60 amp yellow glow plugs - diesel only - if equipped f39 — 40 amp green hvac blower motor f40 — 20 amp blue trailer tow park light - if equipped f41 — 60 amp yellow body controller module (bcm) - feed 2 f42 — 30 amp pink electric park brake (epb) - ...

  • Page 628

    Cavity blade fuse cartridge fuse description f50 — 30 amp pink power liftgate - if equipped f51 — — not used f52 — — not used f53 — 30 amp pink bsm-ecu & valves f54 — 30 amp pink urea heater control unit - if equipped with diesel engine cavity blade fuse cartridge fuse description f55 10 amp red — b...

  • Page 629

    Cavity blade fuse cartridge fuse description f57 20 amp yellow — fuel pump motor f58 10 amp red — occupant classifica- tion module f59 — — not used f60 20 amp yellow — power outlet - cen- ter console f61 — — not used f62 10 amp red — heated mirrors - if equipped f63 25 amp clear — front heated seats...

  • Page 630

    Cavity blade fuse cartridge fuse description f67 — — not used f68 — — not used f69 10 amp red — power transfer unit switch (tsbm) / active grill shutter (ags) - if equipped f70 — — not used f71 20 amp yellow — windshield de-icer - if equipped f72 5 amp tan — intelligent battery sensor (ibs) if equip...

  • Page 631

    Cavity blade fuse cartridge fuse description f77 10 amp red — fuel door release/ brake pedal switch f78 10 amp red — diagnostic port / steering column control module (sccm) / digital tv - if equipped f79 10 amp red — integrated center stack (ics) / hvac / aux switch bank module (asbm) / instrument p...

  • Page 632

    Cavity blade fuse cartridge fuse description f88 15 amp blue — collision mitigation module (cmm) / electrochromatic mirror / smart camera module - if equipped f89 10 amp red — headlamp leveling - if equipped f90 — — not used f91 — — not used f92 20 amp yellow — rear power outlet cavity blade fuse ca...

  • Page 633

    Cavity blade fuse cartridge fuse description f97 10 amp red — occupant restraint controller (orc) f98 25 amp clear — audio amplifier - if equipped f99 — 30 amp pink trailer tow module - if equipped with gasoline engine f100 — — not used interior fuses the interior fuse panel is located in the passen...

  • Page 634

    Cavity blade fuse description f51 10 amp red driver window switch/ power mirrors – if equipped f53 7.5 amp brown uci port (usb & aux) f89 10 amp red door locks – driver un- lock f91 7.5 amp brown fog lamp front left f92 7.5 amp brown fog lamp front right f93 10 amp red low beam right vehicle storage...

  • Page 635

    Replacement bulbs interior bulbs bulb number cargo lamp tl212–2 overhead console lamp plw214–2a reading lamp wl212–2 exterior bulbs bulb number low beam/high beam (bi-halogen) headlamps hir2 low beam/high beam (bi-xenon) headlamps d3s (serviced at an au- thorized dealer) bulb number front park/dayti...

  • Page 636

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Low beam and high beam headlamps bi...

  • Page 637

    3. Firmly grasp the cap and rotate it counterclockwise to unlock it. 4. Firmly grasp the bulb and connector assembly and rotate counterclockwise to remove from the housing. 5. Disconnect the bulb from the electrical connector and then connect the replacement bulb. Caution! Do not touch the new bulb ...

  • Page 638

    4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. 5. Re-install air cleaner filter housing, if removed. Front fog lamp 1. Unlock lower access door in wheel liner. 2. Reach behind the fog lamp housing to access the bulb. 3. Rotate the bulb’...

  • Page 639

    3. Squeeze the two tabs on the side of the bulb socket and pull straight out from the fog lamp. 4. Disconnect the wire harness from the bulb. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, c...

  • Page 640

    Back-up lamp 1. Open the liftgate. 2. Use a fiber stick or flat blade screw driver to pry the lower trim from the liftgate. 3. Once the trim is loose, pull it back exposing the trim panel. 4. Using a fiber stick or flat blade screw driver, open the trim panel exposing the back of the liftgate lamp. ...

  • Page 641

    Fluid capacities u.S. Metric fuel (approximate) 2.4l and 3.2l engines 15.8 gallons 60 liters engine oil with filter 2.4 liter engine (sae 0w-20, api certified) 5.5 quarts 5.2 liters 3.2 liter engine (sae 5w-20, api certified) 6 quarts 5.6 liters cooling system* 2.4 liter engine (mopar® antifreeze/en...

  • Page 642

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the require- ments of chrysler material standard ms-12106. Engine...

  • Page 643

    Component fluid, lubricant, or genuine part spark plugs – 2.4l engine we recommend you use mopar® spark plugs (gap 0.047 in [1.2 mm]) spark plugs – 3.2l engine we recommend you use mopar® spark plugs (gap 0.043 in [1.1 mm]) fuel selection – 2.4l engine 87 octane fuel selection – 3.2l engine 87-89 oc...

  • Page 645: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .644 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .646 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 646

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 647

    Severe duty all models change engine oil at 4000 miles (6,500 km) if the vehicle is operated in a dusty and off road environment. This type of vehicle use is considered severe duty once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check tire pressur...

  • Page 648

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 649

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 650

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 651: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .651 ▫ prepare for the appointment. . . . . . . . . . . . .651 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .651 ▫ be reasonable with requests ....

  • Page 652

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .657 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .657 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .658 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .658 650 if...

  • Page 653

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 654

    Warranty service must be done by an authorized dealer. We strongly recommend that you take the vehicle to an authorized dealer. They know your vehicle the best, and are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trai...

  • Page 655

    Chrysler group llc customer center p.O. Box 21–8004 auburn hills, mi 48321–8004 phone: (877) 426–5337 chrysler canada inc. Customer center p.O. Box 1621 windsor, ontario n9a 4h6 phone: (800) 465–2001 english / (800) 387–9983 french in mexico contact: av. Prolongacion paseo de la reforma, 1240 sante ...

  • Page 656

    Expires. The manufacturer stands behind only the manu- facturer’s service contracts. If you purchased a manufac- turer’s service contract, you will receive plan provisions and an owner identification card in the mail within three weeks of the vehicle delivery date. If you have any questions about th...

  • Page 657

    Warranty information see the warranty information booklet, located on the dvd, for the terms and provisions of chrysler group llc warranties applicable to this vehicle and market. Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- ...

  • Page 658

    In canada if you believe that your vehicle has a safety defect, you should contact the customer service department imme- diately. Canadian customers who wish to report a safety defect to the canadian government should contact trans- port canada, motor vehicle defect investigations and recalls at 1-8...

  • Page 659

    Owner’s manuals these owner’s manuals have been prepared with the assistance of service and engineering specialists to ac- quaint you with specific chrysler group llc vehicles. Included are starting, operating, emergency and mainte- nance procedures as well as specifications, capabilities and safety...

  • Page 660

    Significantly from the norm due to variations in driving habits, service practices, and differences in road charac- teristics and climate. Traction grades the traction grades, from highest to lowest, are aa, a, b, and c. These grades represent the tire’s ability to stop on wet pavement, as measured ...

  • Page 661

    Material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade c corresponds to a level of performance, which all passenger car tires must meet under the federal motor vehicle safety standard no. 109. Grades b and a repre- sent higher le...

  • Page 663: Index

    Index 10

  • Page 664

    Abs (anti-lock brake system) . . . . . . . . . . . . . . . .451 adaptive cruise control (acc) (cruise control) . . .189 adding engine coolant (antifreeze) . . . . . . . . . . . .605 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .514 airbag. . . . . . . . . . . . . . . . . . . ....

  • Page 665

    Automatic transaxle . . . . . . . . . . . . . . . . . . . . . . .417 automatic transmission . . . . . . . . . . . . . . . . . . . .420 adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .613 fluid and filter changes . . . . . . . . . . . . . . . . . .613 fluid change . . . . . . . . . . ...

  • Page 666

    Oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .583 radiator (coolant pressure) . . . . . . . . . . . . . . . .607 carbon monoxide warning . . . . . . . . . . . . . . . . . .118 cargo area cover . . . . . . . . . . . . . . . . . . . . . . . . .306 cargo area features . . . . . . . ...

  • Page 667

    Pressure cap . . . . . . . . . . . . . . . . . . . . . . . . . .607 radiator cap . . . . . . . . . . . . . . . . . . . . . . . . . .607 selection of coolant (antifreeze) . . . . . . . . . . . . .604 corrosion protection . . . . . . . . . . . . . . . . . . . . . . .615 cruise control (speed control)....

  • Page 668

    Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .570 overheating . . . . . . . . . . . . . . . . . . . . . . . . . . .545 emission control system maintenance . . . . . . . . . .586 engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .583 air cleaner . . . . . . . ....

  • Page 669

    Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .592 engine oil disposal . . . . . . . . . . . . . . . . . . . . .592 flashers hazard warning . . . . . . . . . . . . . . . . . . . . . . . .545 turn signal . . . . . . . . . . . . . . . . . . . . . . . . . . .121 flash-to-pass . . . ....

  • Page 670

    Gasoline, clean air . . . . . . . . . . . . . . . . . . . . . . . .512 gasoline (fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . .511 gasoline, reformulated . . . . . . . . . . . . . . . . . . . . .512 gauges coolant temperature . . . . . . . . . . . . . . . . . . . . .324 fuel . . . . . ....

  • Page 671

    Hill start assist. . . . . . . . . . . . . . . . . . . . . . . . . . .456 hitches trailer towing . . . . . . . . . . . . . . . . . . . . . . . . .525 holder, coin. . . . . . . . . . . . . . . . . . . . . . . . . . . . .303 holder, cup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .301 home...

  • Page 672

    Lane change and turn signals . . . . . . . . . . . . . . . .171 lane change assist . . . . . . . . . . . . . . . . . . . . . . . .172 lap/shoulder belts. . . . . . . . . . . . . . . . . . . . . . . . .56 latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 hood . . . . . . . . ...

  • Page 673

    License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .638 lights on reminder . . . . . . . . . . . . . . . . . . . . .169 malfunction indicator (check engine) . . . . . . . . .325 parade mode (daytime brightness) . . . . . . . . . . .175 passing . . . . . . . . . . . . . . . . . . . . ....

  • Page 674

    Memory feature (memory seat) . . . . . . . . . . . . . . .159 memory seat . . . . . . . . . . . . . . . . . . . . . . . . . . . .159 memory seats and radio . . . . . . . . . . . . . . . . . . . .159 methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .513 mirrors . . . . . . . . . ....

  • Page 675

    Oil filter, selection . . . . . . . . . . . . . . . . . . . . . . . .593 onboard diagnostic system . . . . . . . . . . . . . . . . . .585 opener, garage door (homelink®) . . . . . . . . . . . .275 operating precautions . . . . . . . . . . . . . . . . . . . . . .585 operator manual (owner’s manual) ....

  • Page 676

    Rear parksense system . . . . . . . . . . . . . . . . . . . . .231 rear seat, folding . . . . . . . . . . . . . . . . . . . . . . . . .156 rear window defroster . . . . . . . . . . . . . . . . . . . . .309 rear window features . . . . . . . . . . . . . . . . . . . . .308 rear wiper/washer. . . . . ....

  • Page 677

    Safety information, tire . . . . . . . . . . . . . . . . . . . . .474 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 schedule, maintenance . . . . . . . . . . . . . . . . . . . . .644 seat belt maintenance . . . . . . . . . . . . . . . . . . . . . .621 seat belt reminder ...

  • Page 678

    Side view mirror adjustment. . . . . . . . . . . . . . . . .132 signals, turn . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 sky slider power roof. . . . . . . . . . . . . . . . . . . . . .289 smartbeams . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168 snow chains (tire chain...

  • Page 679

    System, remote starting . . . . . . . . . . . . . . . . . . . . .29 tachometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .318 telescoping steering column . . . . . . . . . . . . . . . . .181 temperature control, automatic (atc) . . . . . . . . . .397 temperature gauge, engine coolant ...

  • Page 680

    Tread wear indicators . . . . . . . . . . . . . . . . . . . .493 tire safety information . . . . . . . . . . . . . . . . . . . . .474 tongue weight/trailer weight . . . . . . . . . . . . . . . .527 to open hood . . . . . . . . . . . . . . . . . . . . . . . . . . .164 towing . . . . . . . . . . . . ....

  • Page 681

    Upholstery care . . . . . . . . . . . . . . . . . . . . . . . . . .619 vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . .135 vehicle identification number (vin) . . . . . . . . . . . . .7 vehicle loading . . . . . . . . . . . . . . . . . . . . . . . . . .482 vehicle modifications/a...

  • Page 682

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 683

    1283259cv1 14wk741-126-aa grand cherokee chrysler 1" gutter 12/05/2012 15:56:03 grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2014 gr and cher ok ee 14wk741-126-aa second edition printed in u.S.A. 2 0 1 4 grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2014 gr and cher ok e...