1. DL manuals
  2. Jeep
  3. Automobile
  4. Grand Cherokee SRT 2014
  5. Owner's Manual

Jeep Grand Cherokee SRT 2014 Owner's Manual

Summary of Grand Cherokee SRT 2014

  • Page 1

    Cherokee chrysler group llc o w n e r ’ s m a n u a l 2014 cherokee 14kl74-126-aa first edition printed in u.S.A. 2 0 1 4.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million a...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against oper- ating procedures that could result in a collision or bodily injury. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss important ...

  • Page 10

    Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. 8 introduction.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ ignition node module (ignm) — if equipped. .12 ▫ keyless ignition node (kin) . . . . . . . . . . . . . .13 ▫ key fob — if equipped . . . . . . . . . . . . . . . . . .14 ▫ ignition or accessory...

  • Page 12

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . .25 ▫ programming additional transmitters. . . . . . . .25 ▫ transmitter battery replacement . . . . . . . . . . .25 ▫ general information . . . . . . . . . . . . . . . . . . . .29 䡵 remote starting system — if equipped . . . . . . . . . . . ...

  • Page 13

    ▫ enhanced seat belt use reminder system (beltalert®) . . . . . . . . . . . . . . . . . . . . . . . . . .64 ▫ seat belts and pregnant women . . . . . . . . . . .65 ▫ seat belt extender . . . . . . . . . . . . . . . . . . . . .65 ▫ supplemental restraint system (srs) — air bags . . . . . . . . . . . ...

  • Page 14

    A word about your keys your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a either a bladed key with an immobilizer chip in it, or a key fob with remote keyless entry (rke) transmitter and an ignition node module (ignm). The key...

  • Page 15

    Keyless ignition node (kin) this feature allows the driver to operate the ignition switch with the push of a button, as long as the remote keyless entry (rke) transmitter is in the passenger compartment. The keyless ignition node (kin) has four operating positions, three of which are labeled and wil...

  • Page 16

    Key fob — if equipped the key fob also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the key fob go dead. You can keep the emergency key with ...

  • Page 17

    Note: you can insert the double-sided emergency key into the lock cylinders with either side up. Ignition node module (ignm) emergency key removal keyless ignition node (kin) emergency key removal 2 things to know before starting your vehicle 15.

  • Page 18

    Ignition or accessory on message opening the driver’s door when the ignition is in acc or on (engine not running), a chime will sound to remind you to cycle the ignition to off. In addition to the chime, the ignition or accessory on message will display in the cluster. Note: with the uconnect® syste...

  • Page 19

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. S...

  • Page 20

    Caution! The sentry key® immobilizer system is not compat- ible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the key fobs provided with your new vehicle have been programmed to the vehicle electro...

  • Page 21

    Note: when having the sentry key® immobilizer sys- tem serviced, bring all vehicle keys with you to an authorized dealer. Customer key programming programming key fobs or rke transmitters may be performed at an authorized dealer. General information the sentry key® system complies with fcc rules par...

  • Page 22

    To arm the system follow these steps to arm the vehicle security alarm: 1. Remove the key from the ignition system (refer to ⬙ starting procedures ⬙ in ⬙ starting and operating ⬙ for further information). • for vehicles equipped with keyless enter-n-go™, make sure the vehicle ignition system is ⬙ of...

  • Page 23

    • cycle the vehicle ignition system out of the off position. • for vehicles equipped with keyless enter-n-go™ , press the keyless enter-n-go™ start/stop button (requires at least one valid key fob in the vehicle). • for vehicles not equipped with keyless enter-n- go™ , insert a valid key into the ig...

  • Page 24

    Security system manual override the vehicle security alarm will not arm if you lock the doors using the manual door lock plunger. Illuminated entry the courtesy lights will turn on when you use the remote keyless entry (rke) transmitter to unlock the doors or open any door. This feature also turns o...

  • Page 25

    To unlock the doors and liftgate press and release the unlock button on the rke transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn ...

  • Page 26

    Flash lights with remote key this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, refer to “uconnect® settings” in “understanding your instrument panel” fo...

  • Page 27

    Using the panic alarm to turn the panic alarm feature on or off, press and hold the panic button on the rke transmitter for at least one second and release. When the panic alarm is on, the headlights will turn on, the park lights will flash, the horn will pulse on and off, and the interior lights wi...

  • Page 28

    1. Remove the emergency key by sliding the mechanical latch on the back of the rke transmitter sideways with your thumb and then pull the key out with your other hand. 2. Separating rke halves requires screw removal and gently prying the two halves of the rke transmitter apart. Make sure not to dama...

  • Page 29

    Remove screw from transmitter case separating ignition node module (ignm) transmitter case 2 things to know before starting your vehicle 27.

  • Page 30

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the b...

  • Page 31

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, includ- ing interference that may cause unde...

  • Page 32

    • hood closed • liftgate/flipper glass closed • hazard switch off • brake switch inactive (brake pedal not pressed) • ignition key removed from ignition switch • battery at an acceptable charge level • rke panic button not pressed • system not disabled from previous remote start event • vehicle thef...

  • Page 33

    • remote start aborted — fuel low • remote start aborted — liftgate ajar • remote start disabled — start vehicle to reset the evic message stays active until the ignition is turned to the on/run position. To enter remote start mode press and release the remote start button on the rke transmitter twi...

  • Page 34

    To exit remote start mode without driving the vehicle press and release the remote start button one time or allow the engine to run for the entire 15 minute cycle. Note: to avoid unintentional shutdowns, the system will disable the one time press of the remote start button for two seconds after rece...

  • Page 35

    Remote start comfort systems — if equipped when remote start is activated, the heated steering wheel, and driver heated seat features will automatically turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These featu...

  • Page 36

    Warning! • for personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, o...

  • Page 37

    The doors can also be locked and unlocked with the keyless enter-n-go™ (passive entry) system. For further information, refer to “keyless enter-n-go™ ” in “things to know before starting your vehicle”. If you press the power door lock switch while the ignition is in the acc or on/run position, and a...

  • Page 38

    Automatic unlock doors on exit the doors will unlock automatically on vehicles with power door locks if: 1. The automatic unlock doors on exit feature is en- abled. 2. All doors are closed. 3. The transmission shift lever was not in park, then is placed in park. 4. Any door is opened. Automatic unlo...

  • Page 39

    Note: • when the child lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. • after disengaging the child-protection door lock system, always test the door from the inside to make certain it is in the desir...

  • Page 40

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Keyless enter-n-go™ the passive entry system is an enhancement to the vehicle’s remote keyless entry (rke) system and a feature of...

  • Page 41

    Note: if “unlock all doors 1st press” is programmed all doors will unlock when you grab hold of the front driver’s door handle. To select between “unlock driver door 1st press” and “unlock all doors 1st press”, refer to “uconnect® settings” in “understanding your instru- ment panel” for further info...

  • Page 42

    Fobik-safe only executes in vehicles with passive entry. There are three situations that trigger a fobik-safe search in any passive entry vehicle. 1. A lock request is made by a valid passive entry rke transmitter while a door is ajar. 2. A lock request is made by the passive entry door handle while...

  • Page 43

    To unlock/enter the liftgate the liftgate passive entry unlock feature is built into the electronic liftgate handle. With a valid passive entry rke transmitter within 3 ft (1.0 m) of the liftgate, press the electronic liftgate handle for a power open on vehicles equipped with power liftgate. Press t...

  • Page 44

    Note: if “unlock all doors 1st press” is programmed in evic, all doors will unlock when you push the button on the liftgate. If ⬙ unlock driver door 1st press ⬙ is pro- grammed in uconnect®, only the liftgate will unlock when you press the button on the liftgate. For further information, refer to “u...

  • Page 45

    Note: • after pressing the door handle lock button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • the pas...

  • Page 46

    Windows power windows the window controls on the driver’s door control all the door windows. There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate only when the ignition is in the acc or on/run position. Note: f...

  • Page 47

    Warning! (continued) in the acc or on/run mode. Occupants, particu- larly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto-down feature the driver door power window switch and some model pa...

  • Page 48

    Warning! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Reset auto-up should the auto up feature stop working, the window probably needs to be reset. To reset auto up: 1. Pull the window switch up to close the window c...

  • Page 49

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof or sky slider™ (if equipped) in certain open or partially open positions. This is a normal oc...

  • Page 50

    Note: the liftgate passive entry lock button will only lock the liftgate, the liftgate unlock feature is built into the electronic liftgate handle. Note: use the power door lock switch on either front door trim panel or the remote keyless entry (rke) transmitter to lock and unlock the liftgate. The ...

  • Page 51

    On the remote keyless entry (rke) transmitter. Press the liftgate button on the rke transmitter twice within five seconds, to open the power liftgate. Once the liftgate is open, pressing the button twice within five seconds a second time will close the liftgate. The power liftgate may also be opened...

  • Page 52

    Note: • the power liftgate buttons will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). • the power liftgate will not operate in temperatures below −22°f (−30°c) or temperatures above 150°f (65°c). Be sure to remove any buildup of snow or ice from the liftgate bef...

  • Page 53

    • if your liftgate is power closing and you put the vehicle in gear, the liftgate will continue to power close. However, vehicle movement may result in a detection of an obstruction. Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passenger...

  • Page 54

    • front seat belts incorporate pretensioners that may enhance occupant protection by managing occupant energy during an impact event • all seat belt systems (except the driver’s) include automatic locking retractors (alrs), which lock the seat belt webbing into position by extending the belt all the...

  • Page 55

    Children that are not big enough to wear the vehicle seat belt properly (see section on child restraints) should be secured in the rear seat in child restraints or belt-positioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly bu...

  • Page 56

    Warning! (continued) • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • supplemen...

  • Page 57

    Lap/shoulder belts all seating positions in your vehicle are equipped with lap/shoulder belts. The belt webbing retractor is de- signed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. However, in a col...

  • Page 58

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the front seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go...

  • Page 59

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden st...

  • Page 60

    Warning! (continued) • a shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thigh...

  • Page 61

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt may not protect you properly. In a collisi...

  • Page 62

    Adjustable upper shoulder belt anchorage in the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Press the release button to release the anchorage, and then move it up or down to the position that fits you best. Note: the adjusta...

  • Page 63

    Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold ...

  • Page 64

    If the passenger seating position is equipped with an alr and is being used for normal usage: only pull the belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a ratcheting sound as the belt retracts....

  • Page 65

    Warning! • the belt and retractor assembly must be replaced if the seat belt assembly automatic locking retractor (alr) feature or any other seat belt function is not working properly when checked according to the procedures in the service manual. • failure to replace the belt and retractor assembly...

  • Page 66

    Enhanced seat belt use reminder system (beltalert®) beltalert® is a feature intended to remind the driver and front passenger (if equipped with front passenger beltalert®) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted...

  • Page 67

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt lo...

  • Page 68

    In addition, the vehicle is equipped with a supplemental driver side knee air bag mounted in the instrument panel below the steering column and a supplemental passenger side knee air bag mounted in the instrument panel below the glove compartment. Note: the driver and front passenger advanced front ...

  • Page 69

    This vehicle may be equipped with a front passenger occupant classification system (ocs) that may adjust the inflation rate of the advanced front air bags based upon occupant weight. Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • after...

  • Page 70

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as deter- mined by the occupant restraint controller (orc), which may receive information from the front...

  • Page 71

    Supplemental seat-mounted side air bags (sab) supplemental seat-mounted side air bags (sab) may provide enhanced protection to help protect an occupant during a side impact. The sab is marked with an air bag label sewn into the outboard side of the seats. When the air bag deploys, it opens the seam ...

  • Page 72

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the sab and sabic air bags during deployment could cause you to be severely injured or killed. • should a vehicle rollover occur, the pretensioners and/or sab and sabic ...

  • Page 73

    Warning! • your vehicle is equipped with left and right sabic, do not stack luggage or other cargo up high enough to block the location of the sabic. The area where the side curtain air bag is located should remain free from any obstructions. • do not use accessory seat covers or place objects betwe...

  • Page 74

    Along with seat belts and pretensioners, advanced front air bags work with the supplemental driver and pas- senger side knee air bags and the passenger side knee bolster to provide improved protection for the driver and front passenger. Side air bags also work with seat belts to improve occupant pro...

  • Page 75

    The advanced front air bags and supplemental driver and front passenger knee air bags will not deploy in all frontal collisions, including some that may produce sub- stantial vehicle damage — for example, some pole colli- sions, truck underrides, and angle offset collisions. On the other hand, depen...

  • Page 76

    Turns on the air bag warning light, either momentarily or continuously. A single chime will sound if the light comes on again after initial startup. It also includes diagnostics that will illuminate the instru- ment cluster air bag warning light if a malfunction is noted that could affect the air ba...

  • Page 77

    The ocs will not prevent deployment of the passenger advanced front air bag. The ocs may reduce the inflation rate of the passenger advanced front air bag if the sensors estimate that: • the front passenger seat is unoccupied or has very light objects in it; or • the front passenger seat is occupied...

  • Page 78

    Warning! • never place a rear facing infant seat in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. • children 12 years or younger should always ride buckled up in ...

  • Page 79

    Warning! Occupants in the front passenger seat sitting improp- erly may cause the ocs to not classify the passen- ger’s weight accurately. This may result in serious (continued) warning! (continued) injury or death in a collision. Always wear your seat belt and sit properly, with the seat back in an...

  • Page 80

    • the front passenger seatback is not in the full upright position • the front passenger carries or holds an object while seated (e.G., backpack, box, etc.) not seated properly not seated properly 78 things to know before starting your vehicle.

  • Page 81

    Not seated properly not seated properly 2 things to know before starting your vehicle 79.

  • Page 82

    Warning! Placing an object on the floor under the front pas- senger seat may prevent the ocs from working properly, which may result in serious injury or death in a collision. Do not place any objects on the floor under the front passenger. The air bag warning light will turn on whenever the ocs is ...

  • Page 83

    The front passenger seat is equipped with flip ’n stow™ front passenger seat storage (refer to “understanding the features of your vehicle” for additional informa- tion). Make sure that objects inside the flip ’n stow™ front passenger seat storage bin do not interfere with the latch before closing t...

  • Page 84

    The following requirements must be strictly followed: • do not modify the front passenger seat assembly or components in any way. • do not use prior or future model year seat covers or cushions not designated by chrysler group llc for the specific model being repaired. Always use the correct seat co...

  • Page 85

    When the orc detects a collision requiring the ad- vanced front air bags, it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the advanced front air bags. Different air bag inflation rates are possible, based on several factors, including the collision type and s...

  • Page 86

    Supplemental seat-mounted side air bag (sab) inflator units the supplemental seat-mounted side air bags are de- signed to activate only in certain side collisions. The orc determines if a side collision requires the side air bags to inflate, based on the severity and type of collision. Based on the ...

  • Page 87

    Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of whether or not an air bag should have deployed. Note: in a rollover the pretensioners and/or sab and sabic air bags may deploy on both sides of the vehicle. Front and side impact sensors in f...

  • Page 88

    If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or al...

  • Page 89

    Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! Deployed air bags and seat belt pretensioners can not protect you in another collision. Have the air bags, seat belt pretensioners, and t...

  • Page 90

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion,...

  • Page 91

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of t...

  • Page 92

    Note: edr data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the edr under normal driving conditions and no per- sonal data (e.G., name, gender, age, and crash location) are recorded. However, other parties, such as law en- forcement, could combin...

  • Page 93

    Before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. You should also make sure that you can install it in the vehicle where you will use it. Note: for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck. Ca...

  • Page 94

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 95

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 96

    Older children and child restraints children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- facing in the vehicle. Forward-facing child seats and con- vertible child seats used in the forward-facing direction are for children who are over two ye...

  • Page 97

    Integrated child booster seat — if equipped the integrated child booster seat is located in each out- board second-row passenger seat. The booster seat is de- signed for children weighing between 48 and 85 lbs (22 and 39 kg) and between 47 in (119 cm) and 57 in (145 cm) tall. To position a child int...

  • Page 98

    Warning! Securely lock the seat cushion into position before using the seat. Otherwise, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat cushion could cause serious injury. Children too large for booster seats children who are large enough ...

  • Page 99

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 100

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 101

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seat- ing position • top tether anchorage symbol 2 things to know before starting your vehicle 99.

  • Page 102

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the com- bined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and te...

  • Page 103

    Can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front pas- senger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information. Can the head restraints be remove...

  • Page 104

    Locating the latch anchorages in addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to...

  • Page 105

    Options for installing two child seats using the latch anchorages in this vehicle: 1. Right and left outboard seating positions (1 and 3): install the child seats in the right and left outboard seating positions using lower anchorages a and b, and d and e. Do not use the center seat anchorage, c. If...

  • Page 106

    Warning! (continued) • a child restraint installed in the center position (2) will block the seat belt buckle for the empty left outboard seat behind the driver (3). Do not use this seat for another occupant. • never use the same lower anchorage to attach more than one child restraint. • if you are ...

  • Page 107

    3. Place the child seat between the lower anchorages for that seating position. For some second row seats, you may need to recline the seat and / or raise the head restraint to get a better fit. 4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected se...

  • Page 108

    If the buckled seat belt interferes with the child restraint installation, instead of buckling it behind the child re- straint, route the seat belt through the child restraint belt path and then buckle it. Do not lock the seatbelt. Remind all children in the vehicle that the seat belts are not toys ...

  • Page 109

    Refer to the “automatic locking mode” description un- der “occupant restraints.” the cinching latch plate is designed to hold the lap portion of the seatbelt tight when webbing is pulled tight and straight through a child restraint’s belt path. Please see the table below and the following sections f...

  • Page 110

    What is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint, ...

  • Page 111

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. 2. Pull enough of the seat belt webbing fro...

  • Page 112

    8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “lower anchors and tethers for chil- dren (latch) restraint system” for directions to attach a tether anchor. 9. Test...

  • Page 113

    6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. If the buckl...

  • Page 114

    2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If...

  • Page 115

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly be- hind the child seat to secure a child restraint top tether strap. If your vehicle is equipped with a split rear seat, make sure the tether ...

  • Page 116

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of diff...

  • Page 117

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breath- ing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confin...

  • Page 118

    Seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. Safety checks you should make inside the vehicle seat belts inspect the belt syste...

  • Page 119

    Floor mat safety information always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in o...

  • Page 120

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 121: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 ▫ inside day/night mirror . . . . . . . . . . . . . . . .126 ▫ automatic dimming mirror — if equipped . . .126 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . .128 ▫ p...

  • Page 122

    䡵 to open and close the hood . . . . . . . . .149 䡵 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151 ▫ headlight switch . . . . . . . . . . . . . . . . . . . . .151 ▫ automatic headlights — if equipped . . . . . . .152 ▫ headlights on with wipers (available with automatic headligh...

  • Page 123

    䡵 heated steering wheel — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .166 䡵 electronic speed control — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .169 ▫ to activate . . . . . . . . . . . . . . . . . . . . . . . . . .170 ▫ to set a desired speed . . . . . . ....

  • Page 124

    ▫ normal (fixed speed) cruise control mode . . .194 䡵 forward collision warning (fcw) with mitigation — if equipped . . . . . . .197 ▫ forward collision warning (fcw) with mitigation operation . . . . . . . . . . . . . . . . . . .197 䡵 lane departure warning (ldw) — if equipped . . . . . . . . . . ....

  • Page 125

    ▫ service the parksense® park assist system . . .237 ▫ cleaning the parksense® system . . . . . . . . . .238 ▫ parksense® system usage precautions. . . . . . .238 䡵 parksense® active park assist system — if equipped . . . . . . . . . . . . . . . .241 ▫ enabling and disabling the parksense® active pa...

  • Page 126

    ▫ opening sunroof — manual mode . . . . . . . . .267 ▫ closing sunroof — express. . . . . . . . . . . . . . .267 ▫ closing sunroof — manual mode . . . . . . . . . .267 ▫ venting sunroof — express . . . . . . . . . . . . . .268 ▫ opening power shade — express . . . . . . . . . .268 ▫ opening power sh...

  • Page 127

    䡵 cupholders . . . . . . . . . . . . . . . . . . . . . . . .282 䡵 storage . . . . . . . . . . . . . . . . . . . . . . . . . . . .282 ▫ glove box storage compartment. . . . . . . . . . .282 ▫ console storage compartment . . . . . . . . . . . .283 䡵 cargo area features . . . . . . . . . . . . . . . .2...

  • Page 128

    Mirrors inside day/night mirror a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjus...

  • Page 129

    A counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you. ...

  • Page 130

    Assist call the rear view mirror contains an assist push button which automatically connects the vehicle occupants to one of several predefined locations for immediate support: • roadside assistance – if you get a flat tire, or need a tow, just press the assist button and you’ll be con- nected to so...

  • Page 131

    Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or...

  • Page 132

    Models with express window feature press and release the mirror select button marked l (left) or r (right) and then press one of the four arrow buttons to move the mirror in the direction the arrow is pointing. The selection will time out after 30 seconds of inactivity to guard against accidentally ...

  • Page 133

    Illuminated vanity mirrors — if equipped an illuminated vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automati- cally. Closing the mirror cover will turn off the light. Sun visor “slide-on-rod” feature — if...

  • Page 134

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 135

    Reclining the seatback forward or rearward the seatback can be reclined both forward and rearward. Push the seat recliner switch forward or rearward, the seatback will move in the direction of the switch. Release the switch when the desired position has been reached. Warning! Do not ride with the se...

  • Page 136

    Increase or decrease the lumbar support. Push the switch upward or downward to raise or lower the lumbar support. Manual front seat forward/rearward adjustment on models equipped with manual seats, the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lif...

  • Page 137

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 138

    Manual seat height adjustment — if equipped the driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pull upward on the lever to raise the seat height or push downward on the lever to lower the seat height. Heated seats — if equipped on some model...

  • Page 139

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Uco...

  • Page 140

    Uconnect® 8.4 system — if equipped touch the “controls” soft-key located on the bottom of the uconnect® display. Touch the “driver” or “passenger” seat soft-key once to select hi-level heating. Touch the soft-key a second time to select lo-level heating. Touch the soft-key a third time to shut the h...

  • Page 141

    When the hi-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal hi-level. If the hi-level setting is selected, the system will automatically switch to lo-level after a maximum of 60 minutes ...

  • Page 142

    Warning! The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury o...

  • Page 143

    Note: the head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. Warning! Do not place items over the top of the active head restraint, such as coats, seat covers or portable dvd play...

  • Page 144

    60/40 split folding rear seat with fold-flat feature to provide additional storage area, each rear seat can be folded flat. This allows for extended cargo space and still maintains some rear seating room. Note: prior to folding the rear seat, it may be necessary to position the front seat to its mid...

  • Page 145

    To lower the rear seat 1. Lift the seatback release lever located on the upper outer edge of the seat or pull the pull strap located on the middle outer edge of the seat. 2. Fold the rear seatback completely forward. To raise the rear seat note: if interference from the cargo area prevents the seatb...

  • Page 146

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Driver memory seat — if equipped this feature allows the driver to store up to two dif...

  • Page 147

    The memory switch allows the driver to recall either of the two pre-programmed memory profiles by pressing the appropriate number button on the switch. Programming the memory feature to create a new memory profile, perform the following: note: saving a new memory profile will erase an existing profi...

  • Page 148

    If desired, a second memory profile can be stored into memory as follows: 1. Turn the ignition on. 2. Adjust all memory profile settings to desired prefer- ences (i.E., seat, side mirror and radio station presets). 3. Press and release the set button on the memory switch, then press the number (2) b...

  • Page 149

    To program your rke transmitters, perform the following: 1. Remove the key from the ignition. 2. Select the desired memory profile 1 or 2. 3. Press and release the set button on the memory switch, then within five seconds press and release the side of the rocker switch labeled 1 or 2 accordingly. ⬙ ...

  • Page 150

    To recall the memory settings for driver one, press memory button number 1 or the unlock button on the rke transmitter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 or the unlock button on the rke transmitter linked to memory position 2. A rec...

  • Page 151

    • the easy entry/easy exit feature is disabled when the driver’s seat position is less than 0.9 in (23 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for easy exit or easy entry. Each stored memory setting will have an associated easy entry and e...

  • Page 152

    2. Move to the outside of the vehicle and pull the safety latch release lever forward (toward you). The safety latch release lever is located behind the center front edge of the hood. Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mate...

  • Page 153

    Lights headlight switch the headlight switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, auto- matic headlights — if equipped, instrument panel lights, instrument panel light dimming, interior lights and fog lights — if e...

  • Page 154

    Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch clockwise to the third detent for automatic headlight operation. When the system is on, the headlight time delay feature i...

  • Page 155

    If you turn the headlights off before the ignition, they will turn off in the normal manner. Note: • the lights must be turned off within 45 seconds of placing the ignition in the off position to activate this feature. • the headlight delay time is programmable using the uconnect® system, refer to “...

  • Page 156

    Daytime running lights (drl) the led daytime running lights will come on when- ever the ignition is placed in the run position, the headlights are off, the transmission is moved out of “park” position, and the parking brake is off. The head- light switch must be used for normal nighttime driving. No...

  • Page 157

    To activate the front fog lights, turn on the parking lights or the low beam headlights and press the headlight switch. To turn off the front fog lights, either press the headlight switch a second time or turn off the headlight switch. An indicator light in the instrument cluster illuminates when th...

  • Page 158

    Note: • if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. • a “turn signal on” message will appear in the evic (if...

  • Page 159

    There are courtesy lights located above the front seats. If your vehicle is equipped with a power sunroof the courtesy lights are located above the rear seats. The courtesy lights can be turned on by pressing the lens. To turn the lights off, press the lens a second time. Interior lights the interio...

  • Page 160

    With the parking lights or headlights on, rotating the right dimmer control upward will increase the brightness of the instrument panel lights and lighted cupholders — if equipped. Ambient light control rotate the left dimmer control upward or downward to increase or decrease the brightness of the a...

  • Page 161

    Dome light position rotate the instrument panel dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the instrument panel dimmer control is in this position. Interior light defeat (off) rotate the instrument panel dimmer contro...

  • Page 162

    The rear wiper/washer, refer to “rear window features” in “understanding the features of your vehicle”. Windshield wiper operation rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high w...

  • Page 163

    Caution! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur. Intermittent wiper system use one of the...

  • Page 164

    Windshield washer operation to use the washer, pull the lever rearward toward you and hold while spray is desired. If the lever is pulled while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the lever is released, and then resume the intermittent inter...

  • Page 165

    Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Rain sensing wipers — if equipped this feature senses moisture on the windshield and automaticall...

  • Page 166

    Note: • the rain sensing feature will not operate when the wiper switch is in the low or high-speed position. • the rain sensing feature may not function properly when ice, or dried salt water is present on the windshield. • use of rain-x® or products containing wax or silicone may reduce rain sensi...

  • Page 167

    Remote start mode inhibit — on vehicles equipped with remote starting system, rain sensing wipers are not operational when the vehicle is in the remote start mode. Once the operator is in the vehicle and has placed the ignition switch in the run position, rain sensing wiper operation can resume, if ...

  • Page 168

    To unlock the steering column, push the control handle downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as de- sired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering col...

  • Page 169

    Uconnect® 5.0 system — if equipped press the “climate” hard-key then touch the “heated steering wheel” soft-key to turn on the heated steering wheel. Press the “heated steering wheel” soft-key a second time to turn the heated steering wheel off. Uconnect® 8.4 system — if equipped touch the “controls...

  • Page 170

    Note: the engine must be running for the heated steering wheel to operate. Vehicles equipped with remote start on models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to kn...

  • Page 171

    Warning! (continued) • do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat. Electronic speed control — if equipped when engaged, the electronic speed control...

  • Page 172

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 173

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate electronic speed control without erasing the set speed memory. Pressing the on/off button or turning the ignition switch off erases the set speed memory. To resu...

  • Page 174

    To accelerate for passing press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using electronic speed control on hills the transmission may downshift on hills to maintain the vehicle set speed. Note: the electronic speed control system ma...

  • Page 175

    Acc will allow you to keep cruise control engaged in light to moderate traffic conditions without the constant need to reset your cruise control. Acc utilizes a radar sensor and a forward facing camera designed to detect a vehicle directly ahead of you. Note: • if the sensor does not detect a vehicl...

  • Page 176

    Warning! (continued) • cannot take street, traffic, and weather condi- tions into account, and may be limited upon adverse sight distance conditions. • does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings. • can only apply a maximum of 40...

  • Page 177

    The cruise control system has two control modes: • adaptive cruise control mode for maintaining an appropriate distance between vehicles. • normal (fixed speed) cruise control mode for cruising at a constant preset speed. For additional information, refer to “normal (fixed speed) cruise control mode...

  • Page 178

    Note: any chassis/suspension or tire size modifica- tions to the vehicle will effect the performance of the adaptive cruise control. Activating adaptive cruise control (acc) you can only engage acc if the vehicle speed is above 0 mph (0 km/h). The minimum set speed for the acc system is 20 mph (32 k...

  • Page 179

    To activate push and release the adaptive cruise control (acc) on/off button. The acc menu in the evic displays “acc ready.” to turn the system off, push and release the adaptive cruise control (acc) on/off button again. At this time, the system will turn off and the evic will display “adaptive crui...

  • Page 180

    Warning! Leaving the adaptive cruise control (acc) system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the system off when you are not using it. To set a desired acc speed when...

  • Page 181

    • you press the cancel switch. • an anti-lock brake system (abs) event occurs. • a trailer sway control (tsc) event occurs. • the transmission is shifted into neutral. • the electronic stability control/traction control sys- tem (esc/tcs) activates. • the vehicle parking brake is applied. • driver s...

  • Page 182

    Note: • if your vehicle stays at standstill for longer than 2 seconds, then the driver will either have to press the resume button, or apply the throttle to reengage the acc to the existing set speed. • acc cannot be resumed if there is a stationary vehicle in-front of your vehicle in close proximit...

  • Page 183

    If the set - button is continually pressed, the set speed will continue to decrease in 5 mph (5 km/h) increments until the button is released. The decrease in set speed is reflected in the evic display. Note: • when you override and push the set + button or set - buttons, the new set speed will be t...

  • Page 184

    Using this distance setting and the vehicle speed, acc calculates and sets the distance to the vehicle ahead. This distance setting displays in the evic. Distance setting 4 bars (longest) distance setting 3 bars (long) 182 understanding the features of your vehicle.

  • Page 185

    To increase the distance setting, press the distance set- ting — increase button and release. Each time the button is pressed, the distance setting increases by one bar (longer). Distance setting 2 bars (medium) distance setting 1 bar (short) 3 understanding the features of your vehicle 183.

  • Page 186

    To decrease the distance setting, press the distance setting — decrease button and release. Each time the button is pressed, the distance setting decreases by one bar (shorter). If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle is detected in the same ...

  • Page 187

    When this occurs, you should immediately apply the brakes as needed to maintain a safe distance from the vehicle ahead. Overtake aid when driving with acc engaged and following a target vehicle, the system will provide an additional accelera- tion to assist in passing vehicles in front. This additio...

  • Page 188

    Acc operation at stop if the acc system brings your vehicle to a standstill while following a target vehicle, if the target vehicle starts moving within 2 seconds of your vehicle coming to a standstill, your vehicle will resume motion without the need for any driver action. After the acc system hold...

  • Page 189

    Adaptive cruise control ready when acc is activated but the vehicle speed setting has not been selected, the display will read “adaptive cruise control ready.” press the set + or the set- button (located on the steering wheel) and the following will display in the evic: acc set when acc is set, the ...

  • Page 190

    The “acc / fcw unavailable wipe front radar sensor” message can sometimes be displayed while driving in highly reflective areas (i.E. Tunnels with reflective tiles, or ice and snow). The acc system will recover after the vehicle has left these areas. Under rare conditions, when the radar is not trac...

  • Page 191

    When the condition that deactivated the system is no longer present, the system will return to the “adaptive cruise control off” state and will resume function by simply reactivating it. Note: • if the “acc / fcw unavailable wipe front radar sensor” message occurs frequently (e.G. More than once on ...

  • Page 192

    If weather conditions are not a factor, the driver should examine the windshield and the camera located on the back side of the inside rear view mirror. They may require cleaning or removal of an obstruction. When the condition that created limited functionality is no longer present, the system will...

  • Page 193

    Turns and bends when driving on a curve with acc engaged, the system may decrease the vehicle speed and acceleration for stability reasons, with no target vehicle detected. Once the vehicle is out of the curve the system will resume your original set speed. This is a part of normal acc system functi...

  • Page 194

    Using acc on hills when driving on hills, acc may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, acc perfor- mance may be limited. Lane changing acc may not detect a vehicle until it is completely in the lane in which you ...

  • Page 195

    Narrow vehicles some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead. 3 understanding the features of your vehicle 193.

  • Page 196

    Stationary objects and vehicles acc does not react to stationary objects and stationary vehicles. For example, acc will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if nece...

  • Page 197

    To change between the different cruise control modes, press the adaptive cruise control (acc) on/ off button which turns the acc and the normal (fixed speed) control off. Pressing of the normal (fixed speed) cruise control on/off button will result in turning on (changing to) the normal (fixed speed...

  • Page 198

    Pressing the set (+) button once will result in a 1 mph (1 km/h) increase in set speed. Each subsequent tap of the button results in an increase of 1 mph (1 km/h). While the normal (fixed speed) cruise control is set, you can increase the set speed by pressing and holding the set + button. If the bu...

  • Page 199

    • the braking temperature exceeds normal range (overheated). • the shift lever is removed from the drive position. To resume speed to resume a previously set speed, push the res button and release. Resume can be used at any speed above 20 mph (32 km/h). To turn off the system will turn off and erase...

  • Page 200

    When the system determines that a forward collision is probable, the driver will be provided with audible and visual warnings and may provide a brake jerk warning. If the driver does not take action based upon these progres- sive warnings, then the system will provide a limited level of autonomous b...

  • Page 201

    Note: • the minimum speed for fcw activation is 5 mph (10 km/h). • the fcw alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course prediction. This is expected and is a part of normal fcw activation and functionality. Warning! Forward collision wa...

  • Page 202

    To turn the fcw system off, press the forward collision button once to turn the system off (led turns on). To turn the fcw system back on, press the forward collision button again to turn the system on (led turns off). Changing the fcw status to “off” prevents the system from warning you of a possib...

  • Page 203

    To change the fcw and active braking settings with uconnect® 5.0 system screen — if equipped. Note: the settings can only be changed when the vehicle is in park. Follow these steps to set the fcw and active braking: 1. Press the “+ more” hard-key located on the lower right side of the uconnect® syst...

  • Page 204

    Note: • the system will retain the last setting selected by the driver after ignition shut down. • fcw may not react to irrelevant objects such as overhead objects, ground reflections, objects not in the path of the car, stationary objects that are far away, oncoming traffic, or leading vehicles wit...

  • Page 205

    Lane departure warning (ldw) — if equipped lane departure warning (ldw) operation the lane departure warning (ldw) system is opera- tional at speeds above 37 mph (60 km/h) and below 100 mph (160 km/h). The ldw system uses a forward looking camera to detect lane markings and measure vehicle position ...

  • Page 206

    Turning ldw on or off the default status of ldw is “on”. The lane departure warning button is located on the switch panel below the uconnect® display. To turn the ldw system off, press the lane departure warning button once to turn the system off (led turns on). To turn the ldw system back on, press...

  • Page 207

    Note: the ldw system will retain the last system state on or off from the last ignition cycle when the ignition is changed to the on/run position. Ldw warning display the ldw system will indicate the current lane drift condition through the electronic vehicle information center (evic). 3.5 evic scre...

  • Page 208

    • when the ldw system senses the lane has been approached and is in a lane cross situation, the left thick lane line flashes from white to gray, the left thin line remains solid white and the ldw indicator changes from solid white to flashing yellow. Note: the ldw system operates with the similar be...

  • Page 209

    • when the ldw system senses a lane cross situation, the left thick lane line turns solid white, the left thin line remains solid white. The ldw indicator changes from solid green to solid yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. • ...

  • Page 210

    • when the ldw system senses the lane has been approached and is in a lane cross situation, the left thick lane line flashes from white to gray, the left thin line remains solid white and the ldw indicator changes from solid yellow to flashing yellow. At this time torque is applied to the steering w...

  • Page 211

    7.0 evic screen — if equipped when the ldw system is on; the lane lines are gray when the lane boundaries have not been detected and the ldw indicator is solid white. Left lane departure — only left lane detected • when the ldw system is on, the left line turns from gray to white to indicate that th...

  • Page 212

    • when the ldw system senses the lane has been approached and is in a lane cross situation, the left thick lane line flashes yellow (on/off), the left thin line remains solid yellow and the ldw indicator changes from solid white to flashing yellow. Note: the ldw system operates with the similar be- ...

  • Page 213

    • when the ldw system senses a lane cross situation, the left thick lane line and left thin line turn solid yellow. The ldw indicator changes from solid green to solid yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. • for example: if appro...

  • Page 214

    • when the ldw system senses the lane has been approached and is in a lane cross situation, the left thick lane line flashes yellow (on/off) and the left thin line remains solid yellow. The ldw indicator changes from solid yellow to flashing yellow. At this time torque is applied to the steering whe...

  • Page 215

    Changing ldw status the ldw system settings can be made through the uconnect® system screen. Follow these steps to change the ldw settings: 1. Press the “controls” soft-key located on the bottom of the uconnect® display. 2. Press the “settings” soft-key. 3. Press the “safety & driving assistance” so...

  • Page 216

    Parksense® rear park assist — if equipped the parksense® rear park assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to parksense® system usage precautions for limitations of th...

  • Page 217

    Parksense® warning display the parksense® warning screen will only be displayed if sound and display is selected from the customer - programmable features section of the uconnect® sys- tem. Refer to ⬙ uconnect® settings” in “understanding your instrument panel” for further information. The parksense...

  • Page 218

    If an obstacle is detected in the left and/or right rear region, the display will show a single flashing arc in the left and/or right rear region and will produce a fast sound tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the...

  • Page 219

    Slow tone/solid arc fast tone/flashing arc 3 understanding the features of your vehicle 217.

  • Page 220

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: fast tone/flashing arc continuous tone/flashing arc 218 understanding the features of y...

  • Page 221

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-59 in (200- 150 cm) 59-47 in (150- 120 cm) 47-39 in (120- 100 cm) 39-25 in (100- 65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) arcs — left none none none none none 2nd flashing 1st flashing arcs — center none 6th solid 5th soli...

  • Page 222

    Note: parksense® will reduce the volume of the radio, if on, when the system is sounding an audio tone. Enabling and disabling parksense® parksense® can be enabled and disabled with the parksense® switch, located on the switch panel below the uconnect® display. When the parksense® switch is pressed ...

  • Page 223

    Service the parksense® rear park assist system during vehicle start up, when the parksense® rear park assist system has detected a faulted condition, the instru- ment cluster will actuate a single chime, once per ignition cycle, and it will display the “parksense unavailable wipe rear sensors” or th...

  • Page 224

    Parksense® system usage precautions note: • ensure that the rear bumper is free of snow, ice, mud, dirt and debris to keep the parksense® system oper- ating properly. • jackhammers, large trucks, and other vibrations could affect the performance of parksense®. • when you turn parksense® off, the ins...

  • Page 225

    • on vehicles equipped with a tailgate, parksense® should be disabled when the tailgate is in the lowered or open position and the vehicle is in reverse. A lowered tailgate could provide a false indication that an obstacle is behind the vehicle. Caution! • parksense® is only a parking aid and it is ...

  • Page 226

    Warning! (continued) could detect the ball mount and hitch ball assem- bly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle. Parksense® front and rear park assist — if equipped the parksense® park assist system provides visual and audible indications...

  • Page 227

    If your vehicle is equipped with a manual transmission, the automatic braking function in reverse gear is not available. Note: • the driver is always responsible for controlling the vehicle. • the system is provided to assist the driver and not to substitute the driver. • the driver must stay in ful...

  • Page 228

    Parksense® sensors the four parksense® sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 in (30 cm) up to 79 in (200 cm) from the rear fascia/bumper in the horizontal dire...

  • Page 229

    The parksense® warning screen is located within the electronic vehicle information center (evic). It provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the de- tected obstacle. Refer to “electronic vehicle information center (evic)/setting...

  • Page 230

    Single 1/2 second tone/solid arc slow tone/solid arc 228 understanding the features of your vehicle.

  • Page 231

    Slow tone/solid arc fast tone/flashing arc 3 understanding the features of your vehicle 229.

  • Page 232

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: fast tone/flashing arc continuous tone/flashing arc 230 understanding the features of y...

  • Page 233

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-59 in (200-150 cm) 59-47 in (150- 120 cm) 47-39 in (120- 100 cm) 39-25 in (100- 65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) arcs — left none none none none none 2nd flashing 1st flashing arcs — center none 6th solid 5th solid...

  • Page 234

    Note: parksense® will reduce the volume of the radio, if on, when the system is sounding an audio tone. Front park assist when the vehicle is in drive or non-reverse for manual transmission, the parksense warning screen will be displayed when an obstacle is detected. The system will indicate a detec...

  • Page 235

    No tone/solid arc no tone/flashing arc 3 understanding the features of your vehicle 233.

  • Page 236

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: fast tone/flashing arc continuous tone/flashing arc 234 understanding the features of y...

  • Page 237

    Warning alerts front distance (in/cm) greater than 47 in (120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) arcs — left none none none 2nd flashing 1st flashing arcs — center none 4th solid 3rd flashing 2nd flashing 1st flashing arcs — right none none non...

  • Page 238

    If the uconnect® system is equipped, chime volume settings will not be accessible from the evic. The chime volume settings include low, medium, and high. The factory default volume setting is medium. Parksense will retain its last known configuration state through ignition cycles. Enabling and disab...

  • Page 239

    Reverse and the system is disabled, the evic will display the “parksense off” message for as long as the vehicle is in reverse. The parksense® switch led will be on when parksense® is disabled or requires service. The parksense® switch led will be off when the system is enabled. If the parksense® sw...

  • Page 240

    If ⬙ parksense unavailable wipe rear sensors ⬙ or ⬙ parksense unavailable wipe front sensors ⬙ appears in the electronic vehicle information center (evic) make sure the outer surface and the underside of the rear fascia/bumper and/or front fascia/bumper is clean and clear of snow, ice, mud, dirt or ...

  • Page 241

    • parksense®, when on, will reduce the volume of the radio when it is sounding a tone. • clean the parksense® sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not workin...

  • Page 242

    Caution! (continued) • the vehicle must be driven slowly when using parksense® in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using parksense®. Warning! • drivers must be careful when backing up even when using par...

  • Page 243

    Parksense® active park assist system — if equipped the parksense® active park assist system is intended to assist the driver during parallel and perpendicular park- ing maneuvers by identifying a proper parking space, providing audible/visual instructions, and controlling the steering wheel. The par...

  • Page 244

    Enabling and disabling the parksense® active park assist system the parksense® active park assist system can be en- abled and disabled with the parksense® active park assist switch, located on the switch panel below the uconnect® display. To enable the parksense® active park assist system, press the...

  • Page 245

    • pressing the parksense® front and rear park assist switch • driver’s door is opened • rear liftgate is opened • electronic stability control / anti-lock braking sys- tem intervention • performing 6 parking attempts to position the vehicle into the parking space. The parksense® active park assist s...

  • Page 246

    Parallel parking space assistance operation/ display when the parksense® active park assist system is enabled the “active parksense searching - press ok for perpendicular park” message will appear in the evic display. You may switch to perpendicular parking if you desire. Push the ok button on the l...

  • Page 247

    Once the vehicle is in position, you will be instructed to place the shift lever into the reverse position. When the driver places the shift lever into the reverse position, the system will instruct the driver to check their surroundings, and to remove their hands from the steer- ing wheel note: • i...

  • Page 248

    • if the system is canceled during the maneuver for any reason, the driver must take control of the vehicle. Parking space found — shift to reverse check entire surroundings — remove hands from wheel 246 understanding the features of your vehicle.

  • Page 249

    When the vehicle has been moved into the parallel park position you will be instructed to place the shift lever into the drive position, move forward slowly and check your surroundings. After moving forward and checking your surroundings you may be instructed to place the shift lever into the revers...

  • Page 250

    Your vehicle is now in the parallel park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to park. The ⬙ active parksense complete - check parking position ⬙ message...

  • Page 251

    • the driver needs to make sure that the selected parking space for the maneuver remains free and clear of any obstructions (e.G. Pedestrians, bicycles, etc.) • the driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/ clear of anything that may be ov...

  • Page 252

    Once the vehicle is in position you will be instructed to place the shift lever into the reverse position. When the driver places the shift lever into the reverse position, the system will instruct the driver to check their surroundings, and to remove their hands from the steer- ing wheel. Note: • i...

  • Page 253

    Parking space found — shift to reverse check entire surroundings — remove hands from steering wheel 3 understanding the features of your vehicle 251.

  • Page 254

    When the vehicle has been moved into the perpendicular park position you will be instructed to place the shift lever into the drive position, move forward slowly, and check your surroundings. After moving forward and checking your surroundings you may be instructed to place the shift lever into the ...

  • Page 255

    Your vehicle is now in the perpendicular park position. When the maneuver is complete, the driver will be in- structed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to park. The ⬙ active parksense complete - check parking position ⬙ ...

  • Page 256

    Warning! • drivers must be careful when performing parallel or perpendicular parking maneuvers even when using the parksense active park assist system. Always check carefully behind and in front of your vehicle, look behind and in front of you, and be sure to check for pedestrians, animals, other ve...

  • Page 257

    Parkview® rear back up camera — if equipped your vehicle may be equipped with the parkview® rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed in the touchscreen display alon...

  • Page 258

    The following table shows the approximate distances for each zone: zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm) yellow 1 ft - 3 ft (30 cm - 1 m) green 3 ft or greater (1 m or greater) warning! Drivers must be careful when backing up even when using the parkview® rear back up cam...

  • Page 259

    Note: if snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Turning parkview® on or off — with uconnect® 5.0 1. Press the “settings” button. 2. Press the “safety & assistance” soft-key. 3. Press t...

  • Page 260

    The homelink® buttons that are located in the headliner or sun visor designate the three different homelink® channels. Note: homelink® is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you ...

  • Page 261

    Note: • erasing all channels should only be performed when programming homelink® for the first time. Do not erase channels when programming additional buttons. • if you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the internet at www.Homelink.Com for informat...

  • Page 262

    1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light in view. 3. Simultaneously press and hold both the homelink® button you want to program and the hand-h...

  • Page 263

    Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink® button until the indicator light begins to flash after 20 seconds. Do not release the butto...

  • Page 264

    5. Press and hold the programmed homelink® button and observe the indicator light. • if the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the homelink® button is pressed. • to program the remaining two homelink® buttons, repeat each st...

  • Page 265

    It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. 1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to program while keeping ...

  • Page 266

    3. Without releasing the button proceed with “canadian/ gate operator programming” step 2 and follow all remaining steps. Using homelink® to operate, press and release the programmed homelink® button. Activation will now occur for the programmed device (i.E., garage door opener, gate operator, secur...

  • Page 267

    Warning! • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” fea...

  • Page 268

    Power sunroof with power shade — if equipped the power sunroof switch is located to the left between the sun visors on the overhead console. The power shade switch is located to the right between the sun visors on the overhead console. Warning! • never leave children unattended in a vehicle, and do ...

  • Page 269

    Halfway to the comfort stop position. Press the switch rearward and release it again, the sunroof and sunshade will open fully and stop automatically. This is called “express open”. During express open operation, any movement of the sunroof switch will stop the sunroof. Opening sunroof — manual mode...

  • Page 270

    Venting sunroof — express press and release the ⬙ vent ⬙ button within one-half sec- ond and the sunroof will open to the vent position. This is called “express vent”, and it will occur regardless of sunroof position. During express vent operation, any movement of the switch will stop the sunroof. N...

  • Page 271

    Closing power shade — express press the switch forward and release it within one-half second and the shade will close automatically from any position. The shade will close fully and stop automati- cally. This is called “express close”. During express close operation, any movement of the switch will ...

  • Page 272

    Open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sun- roof opening to minimize t...

  • Page 273

    • opening and closing the sky slider™ repeatedly with- out the engine running may run the battery down. Caution! Failure to follow these cautions can cause damage to the sky slider™ vehicle contents, and the vehicle interior: • never attempt to open or close the sky slider™ when it is frozen. Wait u...

  • Page 274

    Warning! (continued) • before operating the sky slider™ make sure that no moving parts of the sky slider™ can injure a person or animal. • never place any extremities (hands, feet, etc.) near the sky slider™ components or the roof area while operating the sky slider™. • if potential danger exists wh...

  • Page 275

    Opening the sky slider™ using automatic mode press the switch rearward and release it within one- half second and the sky slider™ will open from the front and move automatically toward the rear of the vehicle. Press the switch forward and release it within one- half second and the sky slider™ will o...

  • Page 276

    Using operator mode if the sky slider™ is open from the front, press the switch forward and hold it, the sky slider™ will move forward. Release the switch to stop the sky slider™ travel at any point. If the sky slider™ is open from the rear, press the switch rearward and hold it and the sky slider™ ...

  • Page 277

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sky slider™ in certain open or partially open positions. This is a normal occurrence and can be minim...

  • Page 278

    Caution! Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your new vehicle limited warranty. The front power outlet is located in...

  • Page 279

    The rear power outlet is located in the right rear cargo area. Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. •...

  • Page 280

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 281

    To turn on the power inverter outlet, simply plug in the device. The outlet automatically turns off when the device is unplugged. The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the ...

  • Page 282

    Your mobile phone must be designed for qi wireless charging, be equipped with an aftermarket sleeve or equipped with a back plate from your mobile phone provider. The wireless charging pad is equipped with an anti-slip mat, an adjustable cradle to hold your mobile phone in place and an led indicator...

  • Page 283

    The led indicator will flash green while the mobile phone is charging. The qi enabled phone is able to function normally as it is charging. If the led indicator begins flashing red, see your autho- rized dealer. Caution! Do not place your vehicle key fob on the wireless charging pad, the keyless ent...

  • Page 284

    Cupholders there are two cupholders for the front seat passengers, located in the center console. There are two cupholders for the rear seat passengers, located in the center armrest. Storage glove box storage compartment the glove box storage compartment is located on the right side of the instrume...

  • Page 285

    Their is also an additional storage bin located above the instrument panel in the center of the dash. Console storage compartment some vehicles may be equipped with a wireless charging pad located in the upper portion of the center console. Refer to wireless charging pad-if equipped in this section ...

  • Page 286

    To open, pull up on the latch and lift the cover. The center console has a storage area which can hold cell phones, pdas, and other small items. Center console center console storage 284 understanding the features of your vehicle.

  • Page 287

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injur...

  • Page 288

    Cargo tie-down hooks and loops the tie-downs located on the cargo area floor should be used to secure loads safely when the vehicle is moving. Cargo tie-down loops are located on the trim panels. Warning! • cargo tie-downs are not safe anchors for a child seat tether strap. In a sudden stop or accid...

  • Page 289

    Warning! (continued) • do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be- come a dangerous projectile in a sudden stop or accident. Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It wi...

  • Page 290

    The cover rolls away neatly inside its housing when not in use. You can also remove the cover from the vehicle to make more room in the cargo area. To install the cover, position it in the vehicle so that the flat side of the housing faces upward. Then, insert the right spring-loaded post (located o...

  • Page 291

    Rotate the center portion of the lever upward to the first detent for intermittent operation and to the second detent for continuous rear wiper operation. To use the washer, push the lever forward and hold while spray is desired. If the lever is pushed while in the intermittent setting, the wiper wi...

  • Page 292

    Rear window defroster the rear window defroster button is located on the switch bank by the manual climate controls. Press this button to turn on the rear window defroster and the heated outside mirrors. An indicator in the button will illuminate when the rear window defroster is on. The rear window...

  • Page 293

    Roof luggage rack — if equipped note: roof rack and crossbars cannot be used on vehicles equipped with skyslider®. The load carried on the roof, when equipped with a luggage rack, must not exceed 150 lbs (68 kg), and it should be uniformly distributed over the cargo area. Crossbars should always be ...

  • Page 294

    Warning! Cargo must be securely tied down before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack cautions when carrying cargo on your roof rack. 292 understanding the features...

  • Page 295: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .295 䡵 instrument cluster — base . . . . . . . . . .296 䡵 instrument cluster . . . . . . . . . . . . . . . . .297 䡵 instrument cluster descriptions . . . . .298 䡵 electronic vehicle information center (evic) ....

  • Page 296

    䡵 ipod®/usb/mp3 control — if equipped . .359 䡵 steering wheel audio controls — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .360 ▫ radio operation . . . . . . . . . . . . . . . . . . . . . .360 ▫ cd player . . . . . . . . . . . . . . . . . . . . . . . . . . .361 䡵 cd/dvd disc main...

  • Page 297

    Instrument panel features 1 — air demister outlet 5 — instrument cluster 9 — passenger air bag 13 — stop/start ignition button 2 — air outlet 6 — electronic speed controls 10 — glove compartment 14 — trunk release button 3 — electronic vehicle information center (evic) controls 7 — storage compartme...

  • Page 298

    Instrument cluster — base 296 understanding your instrument panel.

  • Page 299

    Instrument cluster 4 understanding your instrument panel 297.

  • Page 300

    Instrument cluster descriptions 1. Tachometer indicates the engine speed in revolutions per minute (rpm x 1000). 2. High beam indicator indicates that headlights are on high beam. 3. Front fog light indicator — if equipped this indicator will illuminate when the front fog lights are on. 4. Park/head...

  • Page 301

    When the appropriate conditions exist, this display shows the electronic vehicle information center (evic) messages. Refer to “electronic vehicle information center”. 6. Anti-lock brake (abs) light this light monitors the anti-lock brake system (abs). The light will turn on when the ignition switch ...

  • Page 302

    Note: the “esc off indicator light” and the “esc activation/ malfunction indicator light” come on momentarily each time the ignition switch is turned to on/run. Each time the ignition is turned to on/run, the esc system will be on, even if it was turned off previously. The esc system will make buzzi...

  • Page 303

    12. Turn signal indicator the arrows will flash with the exterior turn sig- nals when the turn signal lever is operated. A tone will chime, and an evic message will appear if either turn signal is left on for more than 1 mile (1.6 km). Note: if either indicator flashes at a rapid rate, check for a d...

  • Page 304

    Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and...

  • Page 305

    15. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or ...

  • Page 306

    16. Malfunction indicator light (mil) the malfunction indicator light (mil) is part of an onboard diagnostic system called obd ii that monitors engine and automatic transmission con- trol systems. The light will illuminate when the key is in the on/run position before engine start. If the bulb does ...

  • Page 307

    17. Vehicle security light this light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set. The security light will also come on for about three seconds when the ignition is first turned on....

  • Page 308

    • driver assist • fuel economy info • trip (trip a/trip b) • stop/start • audio info • messages • screen setup • speed warning the system allows the driver to select information by pressing the following buttons mounted on the steering wheel: evic buttons 306 understanding your instrument panel.

  • Page 309

    • up arrow button press and release the up arrow button to scroll upward through the main menu and submenus (main gauge, mph/km/h, vehicle info, terrain, driver assist, fuel economy, trip a, trip b, audio, stored messages, screen set up). • down arrow button press and release the down arrow button t...

  • Page 310

    Electronic vehicle information center (evic) displays — 3.5” display the evic displays are located in the center portion of the cluster and consists of eight sections: 1. Brake warning light — if equipped this light monitors various brake functions, including brake fluid level and parking brake appl...

  • Page 311

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 312

    Operation of the brake warning light can be checked by turning the ignition switch from the off position to the on/run position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light ...

  • Page 313

    4. Reconfigurable telltail display area the main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warn- ing or information messages. These pop up mes...

  • Page 314

    5. Lane departure warning (ldw) the lane departure warning (ldw) system provides the driver with visual and steering torque warnings when the vehicle starts to drift out of its lane unintentionally without the use of a turn signal. When the ldw system is on and ready the lane lines and ldw indicator...

  • Page 315

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 316

    Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 7. Fuel gauge fuel gauge displays the level of fuel in the fuel tank when the ignition switch is in the on/run position. 8. Low fuel telltale when the fuel level reaches approximately 3.0...

  • Page 317

    Warning! If you continue operating the vehicle when the transmission temperature warning light is illumi- nated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. • low coolant level indicator this telltale will turn on to indicate the veh...

  • Page 318

    11. Dedicated speed warning telltale this area displays the dedicated speed warn- ing telltale. 12. Speed for electronic cruise control setting this displays the set speed of the electronic speed control. 13. Reconfigurable telltale area • hill descent indicator — if equipped the symbol illuminates ...

  • Page 319

    14. Reconfigurable telltale display • power steering system over temperature — if equipped if the “power steering system over temp” message and a icon are displayed on the evic screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the p...

  • Page 320

    • oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on....

  • Page 321

    Required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • oil temperature warning light this telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon ...

  • Page 322

    Caution! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear cont...

  • Page 323

    1. Lane departure warning (ldw) the lane departure warning (ldw) system provides the driver with visual and steering torque warnings when the vehicle starts to drift out of its lane unintentionally without the use of a turn signal. When the ldw system is on and ready the lane lines and ldw indicator...

  • Page 324

    If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the brake booster has been detected by the anti-lock brake system (abs) / el...

  • Page 325

    Operation of the brake warning light can be checked by turning the ignition switch from the off position to the on/run position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light ...

  • Page 326

    • unstored messages until run these messages deal primarily with the remote start feature. This message type is displayed until the ignition is in the run state. Examples of this message type are “remote start aborted - door ajar” and “press brake pedal and push button to start”. • five second unsto...

  • Page 327

    • selec speed control indicator — if equipped the symbol illuminates and is active only in 4wd low range when either the hdc switch on the instrument panel is selected or rock mode for selec-terrain is selected. If the t-case is not in 4wd low range, the following message is displayed “selec-speed u...

  • Page 328

    12. Amber reconfigurable telltale display • transmission temperature warning light this light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip con...

  • Page 329

    • low coolant level indicator this telltale will turn on to indicate the vehicle coolant level is low. • windshield washer fluid low indicator this telltale will turn on to indicate the wind- shield washer fluid is low. • 4wd low indicator light — if equipped this light alerts the driver that the ve...

  • Page 330

    13. Odometer display / fuel gauge / temperature gauge / submenu area the odometer display shows the total distance the ve- hicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has bee...

  • Page 331

    Caution! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear cont...

  • Page 332

    • power steering system over temperature — if equipped if the “power steering system over temp” message and a icon are displayed on the evic screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system. You will lose ...

  • Page 333

    • oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on....

  • Page 334

    Required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • oil temperature warning light this telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon ...

  • Page 335

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Electronic vehicle information center (evic) messages • front seatbelts unbuckled • driver seatbelt unbuckled • passenger seatbelt unbuckled • se...

  • Page 336

    • service electronic throttle control • lights on • right turn signal light out • left turn signal light out • turn signal on • vehicle not in park • key in ignition • key in ignition lights on • remote start active key to run • remote start active push start button • remote start aborted fuel low •...

  • Page 337

    • shift not allowed • shift to neutral then drive or reverse • autostick unavailable service required • automatic unavailable use autostick service req. • transmission getting hot press brake • trans. Hot stop safely shift to park wait to cool • transmission cool ready to drive • service transmissio...

  • Page 338

    Vehicle info (customer information features) press and release the up or down arrow button until the vehicle info icon is highlighted in the evic. Press and release the right arrow button and coolant temp will be displayed. Press the left or right arrow button to scroll through the infor- mation sub...

  • Page 339

    Refer to “tire pressure monitoring system (tpms)” under “starting and operating” for further information. Trip info press and release the up or down arrow button until the trip icon is highlighted in the evic (toggle left or right to select trip a or trip b). The trip a information will display the ...

  • Page 340

    Audio press and release the up or down arrow button until the audio display icon is highlighted in the evic. Press and release the right arrow button to scroll through the sub-menus and press the ok button display the active source. Screen setup press and release the up or down arrow button until th...

  • Page 341

    • time • range to empty (rte) • average mpg • current mpg • trip a • trip b upper right • none • compass (default setting) • outside temp • oil temp • time • range to empty (rte) • average mpg • current mpg • trip a • trip b restore to defaults (restores all settings to default settings) • cancel • ...

  • Page 342

    • range to empty • average mpg • current mpg • trip a • trip b • audio information • menu title uconnect® access settings the uconnect® access system uses a combination of soft and hard keys located on the center of the instrument panel that allows you to access and change the customer programmable ...

  • Page 343

    Hard-keys hard-keys are located below the uconnect® access system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side of the climate controls in the center of the instru- ment panel. Turn the control knob to scroll through menus and chan...

  • Page 344

    Soft-keys soft-keys are accessible on the uconnect® access display. Customer programmable features — uconnect® 5.0/8.4 settings press the apps soft-key, then press the settings soft-key to display the menu setting screen. In this mode the uconnect® system allows you to access programmable features t...

  • Page 345

    • display brightness with headlights on when in this display, you may select the brightness with the headlights on. Adjust the brightness with the + and – setting soft-keys or by selecting any point on the scale between the + and – soft-keys. Then touch the arrow back soft-key. • display brightness ...

  • Page 346

    • touchscreen beep when in this display, you may turn on or shut off the sound heard when a touch screen button (soft-key) is pressed. Touch the touchscreen beep soft-key until a check-mark appears next to the setting, showing that setting has been selected. Touch the back arrow soft-key to return t...

  • Page 347

    • set time minutes when in this display, you may adjust the minutes. The sync with gps time soft-key must be unchecked. To make your selection touch the + or - soft-keys to adjust the minutes up or down. Touch the back arrow soft-key to return to the previous menu or touch the x soft-key to close ou...

  • Page 348

    • forward collision warning (fcw) active braking — if equipped the fcw system includes advanced brake assist (aba). When this feature is selected, it will apply the brakes to slow your vehicle in case of potential forward collision. The aba applies additional brake pressure when the driver requests ...

  • Page 349

    • parksense® active park assist — if equipped the rear park assist system will scan for objects behind the vehicle when the transmission shift lever is in re- verse and the vehicle speed is less than 11 mph (18 km/h). The system can be enabled with sound only, or sound and display. To change the par...

  • Page 350

    Refer to “parksense® rear park assist” in “understand- ing the features of your vehicle” for system function and operating information. • tilt mirrors in reverse — if equipped when this feature is selected, the outside sideview mir- rors will tilt downward when the ignition is in the run position an...

  • Page 351

    • parkview® rear backup camera — if equipped your vehicle may be equipped with the parkview® rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed on the radio touchscreen displ...

  • Page 352

    • rain sensing auto wipers when this feature is selected, the system will automati- cally activate the windshield wipers if it senses moisture on the windshield. To make your selection, touch the rain sensing soft-key, until a check-mark appears next to setting, showing that setting has been selecte...

  • Page 353

    • headlight illumination on approach when this feature is selected, the headlights will activate and remain on for 0, 30, 60, or 90 seconds when the doors are unlocked with the remote keyless entry (rke)trans- mitter. To change the illuminated approach status, touch the + or - soft-key to select you...

  • Page 354

    • flash headlights with lock when this feature is selected, the headlights will flash when the doors are locked or unlocked with the remote keyless entry (rke) transmitter. This feature may be selected with or without the sound horn on lock feature selected. To make your selection, touch the flash h...

  • Page 355

    • 1st press of key fob unlocks when 1st press of key fob unlocks is selected, only the driver’s door will unlock on the first press of the remote keyless entry (rke) transmitter unlock button. When 1st press of key fob unlocks is selected, you must press the rke transmitter unlock button twice to un...

  • Page 356

    • memory to fob — if equipped this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection, touch the memory linked to fob soft-key, until a check-mark appears next to setting, showing that setting has been selected....

  • Page 357

    Engine off options after pressing the engine off options soft-key the fol- lowing settings will be available. • engine off power delay when this feature is selected, the power window switches, radio, uconnect® phone system (if equipped), dvd video system (if equipped), power sunroof (if equipped), a...

  • Page 358

    Note: keep magnetic materials away from the top of the instrument panel, such as ipod’s, mobile phones, laptops and radar detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. • perform compass calibration touch...

  • Page 359

    • equalizer when in this display you may adjust the bass, mid and treble settings. Adjust the settings with the + and – setting soft-keys or by selecting any point on the scale between the + and – soft-keys. Then touch the arrow back soft-key. Note: bass/mid/treble allow you to simply slide your fin...

  • Page 360

    Siriusxm setup after pressing the sirius setup soft-key the following settings will be available. • channel skip siriusxm can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scanning. To make your selection, touch the c...

  • Page 361

    Ipod®/usb/mp3 control — if equipped 1 – usb port 2 – sd card slot 3 – aux port located in the front storage area, this feature allows an ipod® or external usb device to be plugged into the usb port. Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versi...

  • Page 362

    Steering wheel audio controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the so...

  • Page 363

    The button located in the center of the left-hand control will tune to the next preset station that you have pro- grammed in the radio preset pushbutton. Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginning...

  • Page 364

    Note: if you experience difficulty in playing a particular disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. Radio operation and mobile phone...

  • Page 365

    Front blower control there are seven blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position. Note: for vehicles equipped with remote start, the climate controls...

  • Page 366

    Temperature control use this control to regulate the tempera- ture of the air inside the passenger com- partment. Rotating the knob counter- clockwise, from top center into the blue area of the scale, indicates cooler tem- peratures. Rotating the knob clockwise, into the red area, indicates warmer t...

  • Page 367

    Panel mode air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Bi-level mode air is directed through the panel and floor outlets. Note: there is a difference in temperature (in any conditions other than full cold or full hot), between the upp...

  • Page 368

    Recirculation control press this button to choose between outside air intake or recirculation of the air inside the vehicle. A led will illuminate when you are in recirculation mode. Only use the recirculation mode to temporarily block out any out- side odors, smoke, or dust, and to cool the interio...

  • Page 369

    Economy mode if economy mode is desired, press the a/c button to turn off the led indicator and the a/c compressor. Rotate the temperature control knob to the desired tem- perature. Also, make sure to select only panel, bi-level or floor modes. Stop/start system – if equipped while in an autostop, t...

  • Page 370

    Soft-keys soft-keys are accessible on the uconnect® system screen. Uconnect® 5.0 manual temperature controls — soft-keys uconnect® 8.4 manual temperature controls — soft-keys 368 understanding your instrument panel.

  • Page 371

    Button descriptions (applies to both hard-keys and soft-keys) 1. Max a/c button press and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manual mode and the max a/c indicator will tur...

  • Page 372

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 373

    7. Modes the airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, demist outlets and defrost outlets. The mode settings are as follows: panel mode air comes from the outlets in the instrument panel. Each of these outlets can be individually adjuste...

  • Page 374

    Defrost mode air comes from the windshield and side window demist outlets. Use defrost mode with maximum temperature settings for best windshield and side win- dow defrosting and defogging. When the defrost mode is selected, the blower level may increase. 8. Climate control off button press and rele...

  • Page 375

    Automatic climate controls with touch-screen — if equipped hard-keys the hard-keys located below the uconnect® screen. Soft-keys soft-keys are accessible on the uconnect® system screen. Uconnect® automatic climate controls — hard-keys uconnect® 8.4 automatic temperature controls — soft-keys 4 unders...

  • Page 376

    Button descriptions (applies to both hard-keys and soft-keys) 1. Max a/c button press and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manual mode and the max a/c indicator will tur...

  • Page 377

    6. Rear defrost button press and release this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 10 minutes. For each additional press of ...

  • Page 378

    8. Passenger temperature control down button provides the passenger with independent temperature control. Push the hard-key button for cooler temperature settings or on the touch-screen, press and slide the soft-key temperature bar towards the blue arrow soft-key for cooler temperature settings. Not...

  • Page 379

    11. Modes the airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, demist outlets and defrost outlets. The mode settings are as follows: panel mode air comes from the outlets in the instrument panel. Each of these outlets can be individually adjust...

  • Page 380

    12. Climate control off button press and release this button to turn the climate control on/off. 13. Driver temperature control down button provides the driver with independent temperature con- trol. Push the hard-key button for cooler temperature settings or on the touch-screen, press and slide the...

  • Page 381

    Note: • if fog or mist appears on the windshield or side glass, select defrost mode and increase blower speed. • if your air conditioning performance seems lower than expected, check the front of the a/c condenser (lo- cated in front of the radiator), for an accumulation of dirt or insects. Clean wi...

  • Page 382

    The windshield. On systems with manual climate con- trols, the recirculation mode is not allowed in defrost mode to improve window clearing operation. Recircula- tion will be disabled automatically if this mode is se- lected. Attempting to use recirculation while in this mode will cause the led in t...

  • Page 383

    Manual operation the system allows for manual selection of blower speed, air distribution mode, a/c status and recirculation control. The blower fan speed can be set to any fixed speed by adjusting the blower control. The fan will now operate at a fixed speed until additional speeds are selected. Th...

  • Page 384

    Vacation storage any time you store your vehicle or keep it out of service (i.E., vacation) for two weeks or more, run the air condi- tioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of co...

  • Page 385

    Control setting suggestions for various weather conditions 4 understanding your instrument panel 383.

  • Page 387: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .390 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .390 ▫ extreme cold weather (below –20°f or −29°c) . . . . . . . . . . . . . . . .391 ▫ if engine fails to start . . . . . . . . . . . . . . . . .391 ...

  • Page 388

    ▫ rear electronic locker (e-locker) system – if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .410 䡵 selec-terrain™ . . . . . . . . . . . . . . . . . . . . .412 ▫ description . . . . . . . . . . . . . . . . . . . . . . . . . .412 䡵 on-road driving tips . . . . . . . . . . . . . . . .4...

  • Page 389

    ▫ hill descent control (hdc) — four-wheel drive models with two-speed transfer case only . .438 ▫ select speed control (ssc) — four-wheel drive models with two-speed transfer case and e-locker only . . . . . . . . . . . . . . . . . . . . . . . .441 ▫ electronic stability control (esc) . . . . . . . ...

  • Page 390

    ▫ life of tire . . . . . . . . . . . . . . . . . . . . . . . . .472 ▫ replacement tires . . . . . . . . . . . . . . . . . . . . .473 䡵 tire chains (traction devices) . . . . . . .475 䡵 tire rotation recommendations . . . . .477 䡵 tire pressure monitor system (tpms) . .478 ▫ base system . . . . . . ....

  • Page 391

    ▫ trailer and tongue weight . . . . . . . . . . . . . .504 ▫ towing requirements . . . . . . . . . . . . . . . . . .506 ▫ towing tips . . . . . . . . . . . . . . . . . . . . . . . . .511 䡵 recreational towing (behind motorhome, etc.) . . . . . . . . . . . .512 ▫ towing this vehicle behind another ve...

  • Page 392

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or with access to...

  • Page 393

    Turn the ignition switch to the start position and release when the engine starts. If the engine fails to start within 10 seconds, turn the ignition switch to the lock position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Tip start feature turn the ignition switch to start po...

  • Page 394

    With tip start if the engine fails to start after you have followed the “normal starting” or “extreme cold weather” proce- dures, it may be flooded. To clear any excess fuel, press the accelerator pedal all the way to the floor and hold it. Then, turn the ignition switch to the start position and re...

  • Page 395

    Warning! Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 volt ac electrical cord could cause electrocution. Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the...

  • Page 396

    Warning! (continued) locked in park, securing the vehicle against un- wanted movement. • when leaving the vehicle, always remove the key fob and lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dan...

  • Page 397

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the shift lever to be placed in park before the ignition switch can be turned to the full off (key removal) position. The key fob can only be removed from the ignition when the ignition is in the...

  • Page 398

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has park, reverse, neu- tral, drive, and electronic range select (ers) shift positi...

  • Page 399

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: • after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park this range supplements the parking...

  • Page 400

    Warning! (continued) • your vehicle could move and injure you and others if it is not completely in park. Check by trying to move the shift lever out of park with the brake pedal released. Make sure the transmission is in park before leaving the vehicle. • it is dangerous to shift out of park or neu...

  • Page 401

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 402

    • with brake pedal and lock button on the shift lever released, verify that the shift lever will not move out of park. Reverse this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral use this range when the vehicle is standing for...

  • Page 403

    Drive this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through all forward gears. The drive position provides optimum driving characteris- tics under all normal operati...

  • Page 404

    Sport this mode alters the transmission’s automatic shift schedule for sportier driving. Upshift speeds are in- creased to make full use of available engine power. Sport mode is activated using the rotary switch on the center console. Refer to ⬙ selec-terrain ⬙ in this section for further informatio...

  • Page 405

    Electronic range select (ers) operation the electronic range select (ers) shift control allows the driver to limit the highest available gear. For example, if you shift the transmission into 5 (fifth gear), the trans- mission will not shift above fifth gear, but will shift through the lower gears no...

  • Page 406

    All wheel drive and four-wheel drive operation single range all wheel drive (awd) — if equipped this feature provides on-demand all-wheel drive (awd). The system is automatic with no driver inputs or additional driving skills required. Under normal driving conditions, the front wheels provide most o...

  • Page 407

    Additionally, on dry pavement under heavy throttle input (where one may have no wheel spin), torque will be sent to the rear in a pre-emptive effort to improve vehicle launch and performance characteristics. Caution! All wheels must have the same size and type tires. Unequal tire sizes must not be u...

  • Page 408

    The four-wheel drive is fully automatic in the normal driving mode. The selec-terrain buttons provide three selectable mode positions: • 4wd low • rear lock • neutral when additional traction is required, the 4wd low range position can be used to force the front and rear wheels to rotate at the same...

  • Page 409

    Shift positions for additional information on the appropriate use of each 4wd system mode position, see the information below: neutral this range disengages the driveline from the powertrain. It is to be used for flat towing behind another vehicle. Refer to “recreational towing” in “starting and ope...

  • Page 410

    Note: if shift conditions/interlocks are not met a mes- sage will flash from the electronic vehicle information center (evic) with instructions on how to complete the requested shift. Refer to “electronic vehicle information center (evic)” in “understanding your instrument panel” for further informa...

  • Page 411

    • shifting into or out of 4wd low is possible with the vehicle completely stopped; however, difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur. The preferred method is with the ve...

  • Page 412

    7. After the shift is completed and the neutral light comes on, release the neutral (n) button. 8. Start the engine. 9. Shift the transmission into reverse. 10. Release the brake pedal for five seconds and ensure that there is no vehicle movement. 11. Turn off the engine. 12. Firmly apply the parkin...

  • Page 413

    Activating the rear e-locker to activate the rear e-locker system, the following conditions must be met: 1. The 4wd system must be in 4wd low. 2. The ignition switch in the on position or the engine running. 3. Vehicle speed must be below 15 mph (24 km/h). 4. To engage rear e-locker, press the rear ...

  • Page 414

    • shifting into or out of rear e-locker is possible with the vehicle completely stopped; however, difficulty may occur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur. The preferred method is for the...

  • Page 415

    Selec-terrain™ consists of the following positions: • auto – fully automatic full time four-wheel drive operation can be used on and off road. Balances traction with seamless steering feel to provide im- proved handling and acceleration over two-wheel drive vehicles. • snow – tuning set for addition...

  • Page 416

    Electronic vehicle information center (evic) display messages when the appropriate conditions exist, a message will appear in the evic display. Refer to “electronic vehicle information center (evic)” in “understanding your instrument panel” for further information. On-road driving tips utility vehic...

  • Page 417

    Driving through water although your vehicle is capable of driving through water, there are a number of precautions that must be considered before entering the water: caution! When driving through water, do not exceed 5 mph (8 km/h). Always check water depth before entering as a precaution, and check...

  • Page 418

    Maintenance after driving through deep water, inspect your vehicle fluids and lubricants (engine, transmission, power trans- fer unit and rear drive module) to assure they have not been contaminated. Contaminated fluids and lubricants (milky, foamy in appearance) should be flushed/changed as soon as...

  • Page 419

    Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle. Always back straight down a hill in reverse gear carefully. Never back down a hill in neutral using only the ...

  • Page 420

    After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect...

  • Page 421

    • if you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material. Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation. Power steering the electric power steering system will give you good...

  • Page 422

    Note: • even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at low speeds and during parking maneuvers. • if the condition persists, see your authorized d...

  • Page 423

    To apply the parking brake manually, pull up on the switch momentarily. You may hear a slight whirring sound from the back of the vehicle while the parking brake engages. Once the parking brake is fully engaged, the brake warning lamp in the instrument cluster and an indicator on the switch will ill...

  • Page 424

    To release the park brake manually, the ignition switch must be on. Put your foot on the brake pedal, then push the parking brake switch down momentarily. You may hear a slight whirring sound from the back of the car while the parking brake disengages. You may also notice a small amount of movement ...

  • Page 425

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave a vehicle equipped with keyless enter-n-go in the acc or on/run mode. A child could operate power windows, other controls, or move the vehicle. • be sure the parking brak...

  • Page 426

    To disengage the parking brake while the vehicle is in motion, release the switch. If the vehicle is brought to a complete stop using the parking brake, when the vehicle reaches approximately 3 mph, the parking brake will remain engaged. Warning! Driving the vehicle with the parking brake engaged, o...

  • Page 427

    Safehold can be temporarily bypassed by pressing the electric park brake switch under conditions that would normally engage safehold. Once manually bypassed, safehold will be enabled again once the vehicle reaches 12 mph (20 km/h) or the ignition is turned to the off position. Hold ‘n go™ hold ‘n go...

  • Page 428

    For up to three minutes. After three minutes, hold ‘n go™ will automatically engage the electric parking brake. Once the electric parking brake is engaged hold ‘n go™ will release the brake pressure and return to the enabled condition. Releasing hold ‘n go™ the driver can depress the accelerator to ...

  • Page 429

    Service mode has requirements that must be met in order to be activated: • the vehicle must be at a standstill. • the park brake must be unapplied. • the transmission must be in park or neutral. While in service mode, the electric park brake fault lamp will flash continuously while the ignition swit...

  • Page 430

    All vehicle wheels and tires must be the same size and type, and tires must be properly inflated, to produce accurate signals for the computer. Warning! Significant over or under-inflation of tires or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. The abs c...

  • Page 431

    Caution! The abs is subject to possible detrimental effects of electronic interference caused by improperly in- stalled aftermarket radios or telephones. Note: during severe braking conditions, a pulsing sen- sation may occur and a clicking noise will be heard. This is normal, indicating that the ab...

  • Page 432

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system commonly referred to as esc. This system includes anti-lock brake system (abs), traction control system (tcs), brake assist system (bas), hill start assist (hsa), electronic roll mitigation (erm...

  • Page 433

    Traction control system (tcs) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the tcs system, brake limit...

  • Page 434

    Warning! The brake assist system (bas) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Bas cannot prevent collisions, in- cluding those resulting from excessive speed in turns, driving on very slippery su...

  • Page 435

    Warning! Many factors, such as vehicle loading, road condi- tions, and driving conditions, influence the chance that wheel lift or rollover may occur. Electronic roll mitigation (erm) cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or...

  • Page 436

    Warning! There may be situations where the hill start assist (hsa) will not activate and slight rolling may occur, such as on minor hills (i.E., less than 7%), or with a loaded vehicle, or while pulling a trailer. Hsa is not a substitute for active driving involvement. It is always the driver’s resp...

  • Page 437

    Warning! (continued) • failure to follow these warnings can result in a collision or serious personal injury. Disabling and enabling hsa this feature can be turned on or turned off. To change the current setting, proceed as follows: for vehicles equipped with the electronic vehicle infor- mation cen...

  • Page 438

    7. Rotate the steering wheel back to center and then an additional one-half turn to the right. 8. Turn the ignition switch to the off position and then back to the on position. If the sequence was com- pleted properly, the “esc off indicator light” will blink several times to confirm hsa is disabled...

  • Page 439

    Once at a standstill hold ‘n go™ will engage by auto- matically holding brake pressure when the driver re- leases the brake pedal. The brake pressure will be held for up to three minutes. After three minutes, hold ‘n go™ will automatically engage the electric parking brake. Once the electric parking...

  • Page 440

    Hill descent control (hdc) — four-wheel drive models with two-speed transfer case only hdc is intended for low speed off road driving while in 4wd low range. Hdc maintains vehicle speed while descending hills during various driving situations. Hdc controls vehicle speed by actively controlling the b...

  • Page 441

    Activating hdc once hdc is enabled it will activate automatically if driven down a grade of sufficient magnitude (greater than approximately 8%). The set speed for hdc is selectable by the driver, and can be adjusted by using the gear shift lever. The following summarizes the hdc set speeds: • p = n...

  • Page 442

    Deactivating hdc hdc will be deactivated but remain available if any of the following conditions occur: • driver overrides hdc set speed with throttle or brake application. • vehicle speed exceeds 20 mph but remains below 40 mph. • vehicle is on a downhill grade of insufficient magni- tude (less tha...

  • Page 443

    • the cluster icon and switch lamp will flash for several seconds then extinguish when hdc deactivates due to excess speed. • the cluster icon and switch lamp will flash when hdc deactivates due to overheated brakes. The flashing will stop and hdc will activate again once the brakes have cooled suff...

  • Page 444

    Enabling ssc ssc is enabled by pressing the ssc switch, but the following conditions must also be met to enable ssc: • driveline is in 4wd low range • vehicle speed is below 5mph • parking brake is released • driver door is closed • driver is not applying throttle activating ssc once ssc is enabled ...

  • Page 445

    • 9th = 5.6 mph (9 km/h) • reverse = .6 mph (1 km/h) • neutral = 1.2 mph (2 km/h) • park = ssc remains enabled but not active note: these ssc default set speeds are dependant on hill grade. That is the steeper the grade of the hill the vehicle travels on the lower the values of the set speed will be...

  • Page 446

    Disabling ssc ssc will deactivate and be disabled if any of the follow- ing conditions occur: • the driver presses the ssc switch. • the driveline is shifted out of 4wd low range. • the parking brake is applied. • driver door opens. • the vehicle is driven greater than 20 mph for greater than 70 sec...

  • Page 447

    Warning! Ssc is only intended to assist the driver in control- ling vehicle speed when driving in off road condi- tions. The driver must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed. Electronic stability control (esc) this system enhances directi...

  • Page 448

    Warning! The electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent col- lisions, including those resulting from excessive speed in turns, driving on very ...

  • Page 449

    Partial off – two-wheel drive vehicles and four- wheel drive vehicles in 2wd and 4wd high range the “partial off” mode is intended for driving in deep snow, sand, or gravel. This mode raises the threshold for tcs and esc activation, which allows for more wheel spin than what esc normally allows. The...

  • Page 450

    Full off – four-wheel drive vehicles in 4wd high and 4wd low range the “full off” mode is intended for off-highway and off-road use when esc stability features could inhibit vehicle maneuverability due to trail conditions. The “esc off” button is located in the lower switch bank below the climate co...

  • Page 451

    Warning! With the esc switched off, the enhanced vehicle stability offered by esc is unavailable. In an emer- gency evasive maneuver, the esc system will not engage to assist in maintaining stability. “full off” mode is only intended for off-highway or off-road use. Esc activation/malfunction indica...

  • Page 452

    Note: • the “esc activation/malfunction indicator light” and the “esc off indicator light” come on momen- tarily each time the ignition switch is turned on. • each time the ignition is turned on, the esc system will be on even if it was turned off previously. • the esc system will make buzzing or cl...

  • Page 453

    Note: tsc cannot stop all trailers from swaying. Warning! If the tsc activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Ready alert braking (rab) – if equipped ready alert braking may reduce the time required to r...

  • Page 454

    Optimal steering behavior in order to reach/maintain vehicle stability. The only notification the driver receives that the feature is active is the torque applied to the steering wheel. Note: the dst feature is only meant to help the driver realize the correct course of action through small torques ...

  • Page 455

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 456

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ ....Blank.... ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t or s = temporary spare tire 31 = overall diameter in inches (in) 21...

  • Page 457

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 458

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 459

    Example: dot ma l9 abcd 0301 01 = number representing the year in which the tire was manufactured (two digits) — 01 means the year 2001 — prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represen...

  • Page 460

    Term definition recommended cold tire inflation pressure vehicle manufacturer’s recommended cold tire inflation pressure as shown on the tire placard. Tire placard a paper label permanently attached to the vehicle describing the vehi- cle’s loading capacity, the original equipment tire sizes and the...

  • Page 461

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loa...

  • Page 462

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this section. To determine the maximum loading conditions of your ...

  • Page 463

    5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult th...

  • Page 464

    462 starting and operating.

  • Page 465

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 466

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear pat- terns...

  • Page 467

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” cold tire infl...

  • Page 468

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 469

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed code). Tire ty...

  • Page 470

    Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). For speeds above 75 mph (120 km/h) refer to original equipment or an authorized tire dealer for recommended safe operating speeds, ...

  • Page 471

    Spare tire matching original equipped tire and wheel – if equipped your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for y...

  • Page 472

    Warning! (continued) replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control. Full size spare – if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equ...

  • Page 473

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your tire and loading inf...

  • Page 474

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 475

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 476

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 477

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clear- ance. Follow these recommendations to guard against damage. • traction device must be of proper size for the tire, as recommended by the traction device manufacturer. • use on front tires only • due to limi...

  • Page 478

    Caution! • damage to 4x2 front wheel drive (fwd) models may result if tire chains or traction devices are used with original equipment size tires. • damage to 4x4 all wheel drive (awd) models without a two-speed power takeoff unit may result if tire chains or traction devices are used with original ...

  • Page 479

    Caution! (continued) • observe the traction device manufacturer’s instruc- tions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufac- turer’s if it is less than 30 mph (48 km/h). • do not use traction devices on a com...

  • Page 480

    Caution! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. Tire rotation schedule should be followed to balance tire wear. Tire pressure monitor system (tpms) the ti...

  • Page 481

    Cold placard pressure in order for the “tire pressure monitoring telltale light” to turn off. The system will automatically update and the “tire pressure monitoring telltale light” will turn off once the system receives the updated tire pressures. The vehicle may need to be driven for up to 20 minut...

  • Page 482

    Caution! (continued) • after inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the tire pressure moni- toring sensor. Note: • the tpms is not intended to replace normal tire care and ma...

  • Page 483

    Base system the tire pressure monitor system (tpms) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is particularly important...

  • Page 484

    Service tpms warning when a system fault is detected, the “tire pressure moni- toring telltale light” will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat, providing the system fault still ex...

  • Page 485

    Vehicles with compact spare 1. The compact spare tire does not have a tire pressure monitoring sensor. Therefore, the tpms will not moni- tor the pressure in the compact spare tire. 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warn- ing ...

  • Page 486

    Premium system – if equipped the tire pressure monitor system (tpms) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is parti...

  • Page 487

    Five seconds, an ⬙ inflate to xx ⬙ message and a graphic showing the pressure values of each tire with the low tire pressure values in a different color. Should this occur, you should stop as soon as possible and inflate the tires with low pressure (those in a different color in the evic graphic) to...

  • Page 488

    Service tpms warning when a system fault is detected, the “tire pressure monitoring telltale light” will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime. In addition, the evic will display a ⬙ service tpm system ⬙ message for three seconds and then ...

  • Page 489

    Light” will no longer flash, and the “service tpm system message will no longer display, and a pressure value will display in place of the dashes. A system fault can occur due to any of the following: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequenc...

  • Page 490

    4. The evic will display a graphic showing the tire pressure value in the same color as the other pressure values in place of the different color low tire pressure value. The evic will also display a “spare low pressure” message to remind you to service the flat tire. Vehicles with compact spare 1. ...

  • Page 491

    5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare, the tpms will update automatically. In addition, the “tpms telltale light” will turn off and the graphic in the evic will display a new pressure value instead of dashes (- -), as long ...

  • Page 492

    Charter, wwfc) which define fuel properties necessary to deliver enhanced emissions, performance, and dura- bility for your vehicle. The manufacturer recommends the use of gasoline that 3.2l engine your engine is designed to meet all emis- sions regulations and provide satisfactory fuel economy and ...

  • Page 493

    Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in starting and driveability prob- lems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the “malfunction indicator ...

  • Page 494

    Mmt in gasoline mmt (methylcyclopentadienyl manganese tricarbonyl) is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantage beyond gasoline of the same octane number without mmt. Gasoline blended wi...

  • Page 495

    Caution! (continued) • an out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate ser- vice. Contact your authorized...

  • Page 496

    Warning! (continued) • guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Adding fuel the gas cap is located behind the fu...

  • Page 497

    Note: • in certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button. Do not pry on the door. • when the fuel nozzle “clicks” or shuts off, the fuel tank is ...

  • Page 498

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gaso...

  • Page 499

    Tighten the fuel filler cap until a “clicking” sound is heard. This is an indication that the fuel filler cap is properly tightened. Refer to “onboard diagnostic system” in “maintaining your vehicle” for further information. Vehicle loading certification label as required by national highway traffic...

  • Page 500

    Each axle gawr is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles or suspension components sometimes specified by purchasers for in- creased durability does not necessarily increase the vehi- cle’s gvwr. Tire size the ...

  • Page 501

    Front or rear axles has been exceeded but the total load is within the specified gvwr. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally....

  • Page 502

    Exceed the gvwr. Refer to “vehicle loading/vehicle certification label” in “starting and operating” for further information. Gross trailer weight (gtw) the gtw is the weight of the trailer plus the weight of all cargo, consumables, and equipment (permanent or tem- porary) loaded in or on the trailer...

  • Page 503

    Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision. Tongue weight (tw) the tongue weight is the downward force exerted on the hitch ball by t...

  • Page 504

    Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kinds of hitches are the most popular on the market today and they are commonly used to tow small and medium sized...

  • Page 505

    Warning! • an improperly adjusted weight distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recr...

  • Page 506

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission model frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.4l/automatic 4x2 or 4x4 32 sq ft (2.97 sq...

  • Page 507

    Which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions. Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of t...

  • Page 508

    Towing requirements to promote proper break-in of your new vehicle drive- train components, the following guidelines are recom- mended: caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, duri...

  • Page 509

    Warning! (continued) • safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parke...

  • Page 510

    Towing requirements – tires • do not attempt to tow a trailer while using a compact spare tire. • proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation proce...

  • Page 511

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 512

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 513

    Towing tips before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Automatic transmission the “drive” range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. H...

  • Page 514

    Highway driving reduce speed. Air conditioning turn off temporarily. Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheel off the ground front-wheel drive models four-wheel drive models all-wheel drive models flat tow none not allowed see ins...

  • Page 515

    Recreational towing — front-wheel drive (fwd) models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is allowed only if the front wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a ...

  • Page 516

    Caution! Towing this vehicle with any of its wheels on the ground can cause severe transmission and/or transfer case damage. Damage from improper towing is not covered under the new vehicle limited warranty. Recreational towing — four-wheel drive models the transfer case must be shifted into neutral...

  • Page 517

    Caution! (continued) • do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Shifting into neutral (n) warning! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the neutral (n) position without first f...

  • Page 518

    6. Using a ballpoint pen or similar object, press and hold the recessed transfer case neutral (n) button (located by the selector switch) for four seconds. The light behind the neutral (n) symbol will blink, indicating shift in progress. The light will stop blinking (stay on solid) when the shift to...

  • Page 519

    Caution! Damage to the transmission may occur if the trans- mission is shifted into park with the transfer case in neutral (n) and the engine running. With the transfer case in neutral (n) ensure that the engine is off before shifting the transmission into park. 15. Attach the vehicle to the tow veh...

  • Page 520

    Shifting out of neutral (n) use the following procedure to prepare your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Apply the parking brake. 3. Turn the ignition switch to the on/run position, but do not start the engine. 4. Press ...

  • Page 521

    Note: when shifting out of transfer case neutral (n), turning the engine off may be required to avoid gear clash. 9. Shift the transmission into park. 10. Release the brake pedal. 11. Disconnect vehicle from the tow vehicle. 12. Start the engine. 13. Press and hold the brake pedal. 14. Release the p...

  • Page 523: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .522 䡵 if your engine overheats . . . . . . . . . . . .522 䡵 jacking and tire changing . . . . . . . . . .523 ▫ jack location/spare tire stowage . . . . . . . . .524 ▫ preparations for jacking . . . . . . . . . . . . . ...

  • Page 524

    Hazard warning flashers the hazard warning flasher switch is located in the switch bank below the radio screen. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Press t...

  • Page 525

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maximum he...

  • Page 526

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack location/spare tire stowage the jack, wheel cho...

  • Page 527

    4. Remove the chocks. 5. Remove the scissors jack and wheel bolt wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the wheel bolt wrench, and remove the wrench from the jack assembly. Note: the jack handle attaches to the side of the jack with two attachment point...

  • Page 528

    Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Preparations for jacking 1. Park the vehicle o...

  • Page 529

    6. Chock both the front and rear of the wheel diagonally opposite of the jacking position. For example, if chang- ing the right front tire, chock the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jacking instructions warning! Carefully follow th...

  • Page 530

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 531

    4. Place the jack underneath the lift area that is closest to the flat tire. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, centering the jack saddle between the locating notches on the sill flange. Jacking locations rear jacking location 6 what...

  • Page 532

    5. Raise the vehicle just enough to remove the flat tire. Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire. 7. Mount the spare...

  • Page 533

    Note: • for vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. • refer to “compact spare tire” and to “limited-use spare” under “tires—general information” in “starting and operating” for additional warnings, cautions, and information about the spare ti...

  • Page 534

    9. Lower the vehicle to the ground by turning the jack handle counterclockwise. 10. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the wheel bolts in a star pattern until each wheel bolt has been tightened twice. The correct ...

  • Page 535

    Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Road tire installation vehicles equipped with ...

  • Page 536

    6. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the wheel bolts in a star pattern until each wheel bolt has been tightened twice. The correct tightness of each wheel bolt is 100 ft/lbs (135 n·m). If in doubt about the corre...

  • Page 537

    5. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel bolts are properly seated against the wheel. Jump-starting procedures if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or ...

  • Page 538

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 539

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper c...

  • Page 540

    8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle. If frequent jump-starting is required to start your vehicle you should have ...

  • Page 541

    Note: press the ⬙ esc off ⬙ switch (if necessary), to place the electronic stability control (esc) system in ⬙ partial off ⬙ mode, before rocking the vehicle. Refer to “electronic brake control” in “starting and operating” for further informa- tion. Once the vehicle has been freed, press the ⬙ esc o...

  • Page 542

    Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use the following procedure to temporarily move the shift lever: 1. Firmly apply the parking brake and turn the engine off. 2. Turn the ignition to the on/run position without starting ...

  • Page 543

    Towing condition wheels off the ground 2wd models awd models 4wd models flat tow none if transmission is operable: • transmission in neutral • 30 mph (48 km/h) max speed • 30 miles (48 km/h) max distance if transmission and transfer case are operable: • transmission in neutral • 30 mph (48 km/h max ...

  • Page 544

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members o...

  • Page 545

    Two-wheel drive models the manufacturer recommends towing your vehicle with all four wheels off the ground using a flatbed. If flatbed equipment is not available, and the transmis- sion is operable, the vehicle may be towed (with front wheels on the ground) with the transmission in neu- tral . Speed...

  • Page 546

    All-wheel drive models the manufacturer recommends towing with all wheels off the ground. If flatbed equipment is not available, and the transfer transmission is operable, the vehicle may be flat towed (with all four wheels on the ground), under the follow- ing conditions: • the transmission must be...

  • Page 547: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 2.4l . . . . . . . . . .547 䡵 engine compartment — 3.2l . . . . . . . . . .548 䡵 onboard diagnostic system — obd ii . .549 ▫ loose fuel filler cap message . . . . . . . . . . . .549 䡵 emissions inspection and maintenance programs . . . . . . ....

  • Page 548

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . .571 ▫ automatic transmission . . . . . . . . . . . . . . . .573 ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . .575 ▫ sky slider™ top care . . . . . . . . . . . . . . . . . .576 ▫ appearance care and protection from corrosion ....

  • Page 549

    Engine compartment — 2.4l 1 — air cleaner filter 5 — power distribution center (fuses) 2 — engine coolant pressure cap 6 — battery 3 — oil fill cap 7 — washer fluid reservoir 4 — brake fluid reservoir 8 — engine oil dipstick 7 maintaining your vehicle 547.

  • Page 550

    Engine compartment — 3.2l 1 — engine coolant reservoir 5 — washer fluid reservoir 2 — engine oil filter access cover 6 — battery 3 — brake fluid reservoir 7 — engine oil fill 4 — power distribution center (fuses) 8 — air cleaner filter 548 maintaining your vehicle.

  • Page 551

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 552

    Tighten the gas cap until a ⬙ clicking ⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If...

  • Page 553

    4. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 554

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 555

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, or air conditionin...

  • Page 556

    Engine oil selection for best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are api certified and meet the requirements of chrysler material standard ms-6395. American petroleum institute (api) engine oil identification ...

  • Page 557

    Engine oil viscosity (sae grade) – 3.2l engine sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on...

  • Page 558

    Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Note: for best access to the oil filter, a drive on hoist should be used instead of a chassis hoist. Engine oil filter selection this manufacturer’s engines have a full-flow type dispos- able oil...

  • Page 559

    Engine air cleaner filter selection the quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar® engine air cleaner filters are a high quality filter and are recommended. Maintenance-free battery your veh...

  • Page 560

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and are identified on the battery case. Cable clamps should b...

  • Page 561

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 562

    However, the manufacturer recommends that air condi- tioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment. Note: use only manufacturer approved a/c system sealers, stop leak products, seal conditioners, compressor oil, and refrigerants....

  • Page 563

    Windshield wiper blades clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the w...

  • Page 564

    Note: the rear wiper arm cannot be raised fully up- ward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. ...

  • Page 565

    4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade and snap the pivot cap into place. Adding washer fluid the windshield and rear window washers share the same fluid reserv...

  • Page 566

    If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriora...

  • Page 567

    Caution! (continued) • damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of ...

  • Page 568

    • do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions. Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam f...

  • Page 569

    Cooling system – drain, flush, and refill if the engine coolant (antifreeze) is dirty or contains visible sediment, clean and flush with oat coolant (antifreeze) that meets the requirements of chrysler material standard ms-12106. Refer to the “maintenance schedule” for the proper maintenance interva...

  • Page 570

    Caution! (continued) • this vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (an- tifreeze) is not recommended. Adding coolant your vehicle has been built with an improved engine coolant (oat coolant conformin...

  • Page 571

    Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. Note: mixing engine coolant (antifreeze) types is not recommended and can result in cooling system dama...

  • Page 572

    Disposal of used engine coolant used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol...

  • Page 573

    If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • do not overfill the coolant expansion bottle. • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine c...

  • Page 574

    Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency...

  • Page 575

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 576

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Refer to “fluids, lubricants, and genuine parts” in this section for fluid specifications. Special additives the manufacturer s...

  • Page 577

    Caution! • if a transmission fluid leak occurs, visit your au- thorized dealer immediately. Severe transmission damage may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid and filter changes under normal operating conditions, the fluid installed at the f...

  • Page 578

    Lubricant selection use only manufacturer’s recommended lubricant. Refer to “fluids, lubricants, and genuine parts” in “maintain- ing your vehicle” for further information. Frequency of fluid change under normal operating conditions, the lubricant in- stalled at the factory will give satisfactory lu...

  • Page 579

    If hand washing: • wash in partial shade instead of direct sun. • wet the entire vehicle before washing the top. • wash the top with a soft, natural bristle scrub brush, and a mild soap solution such as liquid dish washing soap. Do not use detergent. • scrub in all directions, covering an area of ab...

  • Page 580

    Rinse the area with warm water. If the stain is still apparent, repeat the cleaning procedure. When the stain is no longer showing, rinse the complete top with warm water. Let the top dry before opening it. Protection for appearance purposes, you may wish to protect the acrylic (cloth) top periodica...

  • Page 581

    The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road...

  • Page 582

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty r...

  • Page 583

    Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • to remove heavy soil and/or excessive brake dust, use mopar® wheel cleaner. Caution! Do not use scouring pads, steel woo...

  • Page 584

    Interior care instrument panel cover the instrument panel cover has a low glare surface, which minimizes reflections in the windshield. Do not use protectants or other products, which may cause undesirable reflections. Use soap and warm water to restore the low glare surface. Cleaning interior trim ...

  • Page 585

    Cleaning headlights your vehicle is equipped with plastic headlights and fog lights (if equipped) that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize...

  • Page 586

    Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Dry ...

  • Page 587

    Cavity car- tridge fuse mini- fuse description f2 — — battery feed (b+) f3 225 amp — alternator f4 150 amp — cabin heater - diesel engine only f5 70 amp tan — power steering f7 — 15 amp blue powertrain control module - diesel engine only f8 — 25 amp natural engine control module (ecm)/fuel injectors...

  • Page 588

    Cavity car- tridge fuse mini- fuse description f19 40 amp green — starter f20 — 10 amp red a/c clutch f22 — 5 amp tan radiator fan enable f23 70 amp tan — body controller mod- ule (bcm) - feed 1 f26 30 amp green — fuel heater - diesel only f28 — 15 amp blue transmission control module (tcm) - zf 9–s...

  • Page 589

    Cavity car- tridge fuse mini- fuse description f40 20 amp blue — trailer tow park light - if equipped f41 60 amp yellow — body controller mod- ule (bcm) - feed 2 f42 30 amp green — electric park brake (epb) - left f43 — 20 amp yellow trailer tow left stop/turn light - if equipped f44 30 amp green — ...

  • Page 590

    Cavity car- tridge fuse mini- fuse description f55 — 10 amp red rear camera/ blindspot monitoring f56 — 15 amp blue ignition node module (ignm)/kin/rf hub/electric steering column lock (esl) f57 — 20 amp yellow fuel pump motor f58 — 10 amp red voltage stabilization module (vsm) f60 — 20 amp yellow p...

  • Page 591

    Cavity car- tridge fuse mini- fuse description f66 — 10 amp red in car temperature sensor/humidity sensor/driver assist system module (dasm)/park assist (pam) f69 — 10 amp red transfer case switch (tsbm)/active grill shutter (ags) f71 — 20 amp yellow windshield de-icer - if equipped f72 — 20 amp yel...

  • Page 592

    Cavity car- tridge fuse mini- fuse description f79 — 10 amp red integrated center stack (ics)/hvac/ aux switch bank module (asbm)/ instrument panel cluster (ipc) f80 — 20 amp yellow radio/cd f83 30 amp green — headlamp washer pump - if equipped f84 20 amp blue — trailer tow back-up lamps - gasoline ...

  • Page 593

    Cavity car- tridge fuse mini- fuse description f96 — 10 amp red occupant restraint controller (orc) f97 — 10 amp red occupant restraint controller (orc) f98 25 amp natural — hifi amplifier - if equipped f99 30 amp green — trailer tow module - if equipped replacement bulbs interior bulbs bulb number ...

  • Page 594

    Bulb number front turn signal lamps 7440na front side marker lamps 194 front fog lamps h11 rear tail/stop/turn sig- nal lamps led ( serviced at an authorized dealer) center high mounted stop lamp (chmsl) led (serviced at an authorized dealer) back-up lamps w16w license plate lamp w5w bulb replacemen...

  • Page 595

    Bi-halogen headlamps 1. Unlock upper access door in wheel liner. 2. Reach behind the headlamp housing to access the headlamp bulb cap. 3. Firmly grasp the cap and rotate it counterclockwise to unlock it. 4. Firmly grasp the bulb and connector assembly and rotate counterclockwise to remove from the h...

  • Page 596

    4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. 5. Re-install air cleaner filter housing, if removed. Front fog lamp 1. Unlock lower access door in wheel liner. 2. Reach behind the fog lamp housing to access the bulb. 3. Rotate the bulb’...

  • Page 597

    Bodyside mounted back-up lamp 1. Open the liftgate. 2. Remove the screws that fasten the tail lamp housing to the vehicle. 3. Grasp the tail lamp and pull firmly rearward to disengage the lamp from the vehicle. 4. Disconnect the electrical connector. 5. Twist the socket counterclockwise and remove f...

  • Page 598

    8. Replace the bulb, reinstall the socket. 9. Connect the electrical connector. 10. Reinstall the trim panel and the lower trim. 11. Close the liftgate. License plate lamp 1. Using a small screwdriver, press inward the locking tab on the side of the lamp assembly and pull down on the lamp assembly f...

  • Page 599

    U.S. Metric 3.2 liter engine (mopar® antifreeze/engine coolant 10 year/150,000 mile formula) 10 quarts 9.5 liters * includes heater and coolant recovery bottle filled to max level. Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you...

  • Page 600

    Component fluid, lubricant, or genuine part engine oil – 3.2l engine we recommend you use api certified sae 5w-20 engine oil, meeting the requirements of chrysler material standard ms-6395. Refer to your engine oil filler cap for correct sae grade. Engine oil filter we recommend you use a mopar® eng...

  • Page 601

    Chassis component fluid, lubricant, or genuine part automatic transmission we recommend you only use mopar® zf 8&9 speed atf™ automatic transmission fluid, shell l12108 transmission fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Br...

  • Page 603: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .602 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .604 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 604

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 605

    Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire inflation pressures and look for unusual wear or damage • check the fluid levels of the coolant reservoir and brake master cylinder, fill as needed • check function of all interior and...

  • Page 606

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 607

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 608

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 609: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . .609 ▫ prepare for the appointment. . . . . . . . . . . . .609 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .609 ▫ be reasonable with requests . . . . ....

  • Page 610

    䡵 department of transportation uniform tire quality grades . . . . . . . . .615 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .616 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .616 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .617 608 if you need consum...

  • Page 611

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 612

    Warranty service must be done by an authorized dealer. We strongly recommend that you take the vehicle to an authorized dealer. They know your vehicle the best, and are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trai...

  • Page 613

    Chrysler canada inc. Customer center p.O. Box 1621 windsor, ontario n9a 4h6 phone: (800) 465–2001 english / (800) 387–9983 french in mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer ass...

  • Page 614

    Service contract you may have purchased a service contract for a vehicle to help protect you from the high cost of unexpected repairs after the manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufactur...

  • Page 615

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addi- tion, certain fluids contained in vehicles and certain products of component wear con...

  • Page 616

    Campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. To contact nhtsa, you may either call the auto safety hotline toll free at 1–888–327–4236 (tty: 1–800–424– 9153), or go to http://www.Safercar.Gov; or write to: administr...

  • Page 617

    Diagnostic procedure manuals diagnostic procedure manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and cor...

  • Page 618

    Treadwear the treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relativ...

  • Page 619

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 621: Index

    Index 10

  • Page 622

    Abs (anti-lock brake system) . . . . . . . . . . . . . . . .427 adaptive cruise control (acc) (cruise control) . . .172 adding engine coolant (antifreeze) . . . . . . . . . . . .568 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .492 airbag. . . . . . . . . . . . . . . . . . . ....

  • Page 623

    Automatic transaxle . . . . . . . . . . . . . . . . . . . . . . .393 automatic transmission . . . . . . . . . . . . . . . . . . . .395 adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .575 fluid and filter changes . . . . . . . . . . . . . . . . . .575 fluid change . . . . . . . . . . ...

  • Page 624

    Radiator (coolant pressure) . . . . . . . . . . . . . . . .569 carbon monoxide warning . . . . . . . . . . . . . . . . . .115 cargo area cover . . . . . . . . . . . . . . . . . . . . . . . . .287 cargo area features . . . . . . . . . . . . . . . . . . . . . . .285 cargo compartment . . . . . . . . ....

  • Page 625

    Points to remember . . . . . . . . . . . . . . . . . . . . .570 pressure cap . . . . . . . . . . . . . . . . . . . . . . . . . .569 radiator cap . . . . . . . . . . . . . . . . . . . . . . . . . .569 selection of coolant (antifreeze) . . . . . . . . . . . . .567 corrosion protection . . . . . . . . ...

  • Page 626

    Emergency, in case of hazard warning flasher . . . . . . . . . . . . . . . . . .522 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .523 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .535 overheating . . . . . . . . . . . . . . . . . . . . . . . . . . .522 emiss...

  • Page 627

    Fabric care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .582 filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .556 air conditioning . . . . . . . . . . . . . . . . . . . . . . .382 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .556 engine oil di...

  • Page 628

    Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .597 tank capacity . . . . . . . . . . . . . . . . . . . . . . . . . .596 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .584 garage door opener (homelink®) . . . . . . . . . . . .257 gas cap (fuel filler cap) ...

  • Page 629

    Heated seats. . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .362 heater, engine block . . . . . . . . . . . . . . . . . . . . . . .392 high beam indicator . . . . . . . . . . . . . . . . . . . . . . .298 high beam/lo...

  • Page 630

    Keyless entry system . . . . . . . . . . . . . . . . . . . . . . .22 key, programming . . . . . . . . . . . . . . . . . . . . . . . . .19 key, replacement . . . . . . . . . . . . . . . . . . . . . . . . . .18 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 key, sentry (i...

  • Page 631

    High beam . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 high beam indicator . . . . . . . . . . . . . . . . . . . . .298 high beam/low beam select . . . . . . . . . . . . . . .156 hill descent control indicator . . . . . . . . . . . . . .438 illuminated entry . . . . . . . . . . . . . ....

  • Page 632

    Maintenance free battery. . . . . . . . . . . . . . . . . . . .557 maintenance procedures . . . . . . . . . . . . . . . . . . . .552 maintenance schedule . . . . . . . . . . . . . . . . . . . . . .602 malfunction indicator light (check engine). . . . . . .304 manual, service . . . . . . . . . . . . ...

  • Page 633

    Filter disposal . . . . . . . . . . . . . . . . . . . . . . . . .555 identification logo . . . . . . . . . . . . . . . . . . . . . .554 materials added to . . . . . . . . . . . . . . . . . . . . . .555 recommendation . . . . . . . . . . . . . . . . . . . . . . .554 synthetic . . . . . . . . . . . . ...

  • Page 634

    Radial ply tires . . . . . . . . . . . . . . . . . . . . . . . . . .466 radiator cap (coolant pressure cap) . . . . . . . . . . .569 radio operation . . . . . . . . . . . . . . . . . . . . . . . . . .362 radio remote controls . . . . . . . . . . . . . . . . . . . . .360 rain sensitive wiper system ....

  • Page 635

    Roof type carrier . . . . . . . . . . . . . . . . . . . . . . . . .291 rotation, tires . . . . . . . . . . . . . . . . . . . . . . . . . . .477 safety checks inside vehicle. . . . . . . . . . . . . . . . . .116 safety checks outside vehicle . . . . . . . . . . . . . . . .118 safety defects, reportin...

  • Page 636

    Service assistance . . . . . . . . . . . . . . . . . . . . . . . . .609 service contract . . . . . . . . . . . . . . . . . . . . . . . . . .612 service manuals . . . . . . . . . . . . . . . . . . . . . . . . . .614 shifting automatic transmission . . . . . . . . . . . . . . . . . .395 shift lever ov...

  • Page 637

    Sun roof (sky slider power) . . . . . . . . . . . . . . . . .270 sun visor extension . . . . . . . . . . . . . . . . . . . . . . .131 supplemental restraint system - airbag . . . . . . . . . .65 sway control, trailer. . . . . . . . . . . . . . . . . . . . . . .501 synthetic engine oil . . . . . . . ...

  • Page 638

    Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .454 snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . .467 spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .471 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . .508 tread wear indicato...

  • Page 639

    Tread wear indicators . . . . . . . . . . . . . . . . . . . . . .472 turn signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155 uniform tire quality grades . . . . . . . . . . . . . . . . .615 universal transmitter . . . . . . . . . . . . . . . . . . . . . .257 unleaded gasoline . . ....

  • Page 640

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed prop- erly by trained personnel. The following must be obs...

  • Page 641

    Cherokee chrysler group llc o w n e r ’ s m a n u a l 2014 cherokee 14kl74-126-aa first edition printed in u.S.A. 2 0 1 4.