KAM Laser Tri260 SD FScan Instruction Manual - page 5
DMX channels assignment:
Channel
DMX512 VALUE
FUNCTION
1.Control Mode
0-63
Sound control (3-10ch not available)
64-149
Auto mode (3-10chnot available)
150-199
DMX control
200-255
Auto mode
F
I
R
S
T
P
A
T
T
E
R
N
G
R
O
U
P
2.Blanking
& Blackout
0-5
blackout
6-15
red
16-25
green
26-35
yellow
36-105 (Ch1 must be 200-255)
single colour(auto) R-G-Y Cycling slow to fast
106-175 (Ch1 must be 200-255)
tri-colour(auto) Cycling slow to fast
176-245 (Ch1 must be 200-255)
tri-colour(move) Cycling slow to fast
246-255 (Ch1 must be 200-255)
bounded colour - Cycling
3.Pattern
0-255
124patterns(0-255)
4.Vertical
Move
0-127
manual vertical move
128-191 (Ch1 must be 200-255)
auto up, speed up accordingly
192-255 (Ch1 must be 200-255)
auto down, speed up accordingly
5.Horizontal
Move
0-127
manual horizontal
128-191 (Ch1 must be 200-255)
manual right, speed up accordingly
192-255 (Ch1 must be 200-255)
manual left, speed up accordingly
6.Vertical Roll
0-127
manual vertical rotation
128--255 (Ch1 must be 200-
255)
auto vertical rotation, speed up accordingly
7.Horizontal
Roll
0-127
manual horizontal rotation
128-255 (Ch1 must be 200-255)
auto horizontal rotation
8.Rotation
0-127
manual rotation
128-191 (Ch1 must be 200-255)
auto clockwise rotation, speed up accordingly
192-255 (Ch1 must be 200-255)
auto anti-clockwise rotation, speed up accordingly
9.Zoom In
& Out
0-85 (Ch1 must be 200-255)
from small to large, speed up accordingly
86-170 (Ch1 must be 200-255)
from large to small, speed up accordingly
171-255 (Ch1 must be 200-255)
Large
– small – large, slow to fast
10.Point Draw
0-255
0 Full, 1-255 small to large
SD Card Controlling Mode
The panel can be used to access some important parameters for the ILDA projector.
If the memory of the panel is empty, it displays “Err” at power-on.
At normal function, if parameters are set correctly, the panel displays the actual DMX base address, for
example “001”.
There are 3 keys from left to right:
1. FUNC
By pressing FUNC, the actual parameter for changing is selected.
There are 3 parameters currently available:
“Adr” = DMX base address
“Int” = max. Intensity for colour- and intensity output laser
“Ort” = orientation of the projection
2. SEL
After selecting the parameter with FUNC, press SEL and the current stored value will be
displayed.
By pressing SEL again, the digit for changing will blink.
Pressing Select multiple times will activate all digits by flashing one after the other.
3. Up
Use this key to change the current number in the blinking digit. The number will be
increased.
When reaching the maximum number (9), the number will be start from zero again.
Example:
Set DMX base address to 200.
Press “FUNC” until “Adr” blinks
Press “SEL” until current value is displayed and right digit blinks
Press “Up” until “0” is reached.
Press “SEL” to go to middle digit
Press “Up” until “0”.
Press “SEL” until left digit blinks
Press “Up” until “2” is reached.