Summary of DCA 22
Page 1
Owner manual dca water pumps.
Page 2
6 storage unscrew the drain plug to allow all the water in the pump to drain out. Make sure the pump is empty before replacing the drain plug. Storage when pump is out of service for long periods, drain it and store in a dry, and well ventilated room. Pull engine cord until compressed time so valves...
Page 3
7 maintenance years, but like all other machinery, they require regular inspection and care. The purpose of regular inspection and maintenance is to prevent breakdowns and to obtain the longest service life possible. This pump does not need external lubrication, because the liquid that is being pump...
Page 4
Release the start handle gently instead of suddenly to protect the starter from being damaged. ! Caution starting up in high altitude regions in high altitude places, standard carburetor produces a dense mix of fuel and air, resulting in decreases in the engine performance and increased fuel consump...
Page 5
Note use in extremely dusty area, the job should be done more often. Should be done by your dealer, unless you are equipped with proper repair tools, and are proper trained and are qualified. Engine oil replacement a warm-up engine can assure quick oil draining. Remove the dipstick and oil drain plu...
Page 6
+ + check the spark plug just with eyes. If there exists obvious wear sign around it or gasket is cracked, please replace with a new one. Before reinstalling a spark plug, clean it first with a wire brush. Measure spark plug clearance with a feeler gauge and adjust it by bending the side electrode, ...
Page 7
+ + engine oil alarm system (installation location) the engines oil alarm system was designed to avoid engine damage due to oil low level in the crankcase. Before the engine oil level in the crankcase drops down below the safety line, the alarm system will stop the engine automatically (while the en...
Page 8
07 open the fillings plug, and fill the pump casing. To fill the pump casing it is necessary to use one to 3 gallons of water (depending on the pump model). When there is no plug in the elbow, fill the casing through the discharge connector. It may be necessary to disconnect the quick connect on the...
Page 9
Examine suction hose or pipe connections. Air leaks in the suction line and connections to pump are the most frequent causes of priming trouble. Use a new gasket in the hose coupling. New couplings sometimes require two gaskets. The hose lining may also become loose and clog the hose. Keep the pump ...
Page 10
Pump location s u c t i o n a n d d i s c h a r g e h o s e s install a 90° elbow (supplied) on the pump's discharge and then attach the quick connectors. The suction and discharge should have a male adapter to connect the hose. The fittings should have the same diameter as the suction diameter. Use...
Page 11
9 assembly process b e f o r e a s s e m b l i n g (only for pump ends) check that engine flange and shaft measures are in accordance with diameter and threaded shaft. All units are partially assembled. In the box there are bags with the necessary screws and accessories to complete the assembly. Whe...
Page 12
8 12 16 7 11 15 6 10 14 5 9 13 25 right view left view frame fuel tank air filter muffler oil plug filling plug drain plug dipstick ohv engine 04 o w n e r m a n u a l d c a k at s u p o w e r w at e r p u m p s o w n e r m a n u a l d c a k at s u p o w e r w at e r p u m p s.
Page 13
17 place the casing on the back plate. Tighten the casing with the washers and screws provided. Tighten the screws well and evenly in an "x" sequence. Place the drain plug. Place the suction connection along with the gasket and screws, on the suction port. Tighten suction connection well to prevent ...
Page 14
10 parts list 27 time katsu power engine 168f katsupower engine 168f-2 katsupower engine 177f pump dca dca 22/168f time no. *1 *1 *1 2 dca 33/168f-2 dca 44/177f 1 - - 1 - 1 - 1 - - 1 1 spare parts quantity descripcion back plate impeller volute time no. 3 mechanical seal 5 gasket (o-ring) 4 6 7 quan...
Page 15
Table of contents 3 5 6 7 9 11 16 21 23 27 unpacking the equipment planning the installation installation priming before starting start up maintenance troubleshooting assembly process parts list page o w n e r m a n u a l d c a k at s u p o w e r w at e r p u m p s o w n e r m a n u a l d c a k at s...
Page 16
O w n e r m a n u a l d c a k at s u p o w e r w at e r p u m p s.
Page 17
This manual gives you operation and maintenance instructions of your new katsu power gasoline pump. Before starting the engine read carefully, and follow the instructions to get the best engine-pump performance and longest life. If you have any question please contact the nearest dealer. This manual...