Kelvinator KSE26CRB User Manual - page 6
Kelvinator Air Conditioning
using the remote control 11
10 using the remote control
Kelvinator Air Conditioning
MODE
❄
•
To set the horizontal air flow direction (left-right)
• Adjust the vertical louver manually using the lever
on the left or right side of the vertical louver arm
(Depending on model). Take care not to catch fingers
on the fan, horizontal louver or to damage vertical
louvers. When the air conditioner is in operation
and the horizontal louver is in a specific position,
move the lever at left (or right, depending on model)
end of the air outlet to the desired position.
Range
Vertical
louver
Left and right air flow
caution
• The
aim/swing
button will be disabled when the air
conditioner is not in operation(including when the
TIMER ON is set).
• Do not operate the air conditioner for long periods
with the air flow direction set downward in cooling or
dry mode. Otherwise, condensation may occur on the
surface of the horizontal louver causing moisture to
drop on to the floor or on furnishings.
• Do not move the horizontal louver manually. Always
use the
aim/swing
button. If you move this louver
manually, it may malfunction during operation. If the
louver malfunctions, stop the air conditioner once and
restart it.
• When the air conditioner is started immediately after
it was stopped, the horizontal louver might not move
for approximately 10 seconds.
TIMER ON
TIMER OFF
(Off
Start
Stop operation)
This feature is useful when you want to start the air
conditioner before you wake up and stop it after you leave
the house.
Example:
To start the air conditioner at 6:00 the next morning, and
stop it at 8:00.
1 Press the CLOCK/TIMER button, the TIMER ON indicator
illuminates and the set time flashes.
2 Use the TEMP/TIME button to display "6:00" besides the
TIMER ON display of the remote control.
3 Press the CLOCK/TIMER button again to activate the
TIMER OFF feature.
4 Use the TEMP/TIME button to display "8:00" besides the
TIMER OFF display.
5 Wait for 3 seconds and the setting time stops flashing
and this function is activated. The area reverts back to
displaying the clock time.
Off
Stop
Start
6:00
8:00
Notes: The timer setting (TIMER ON or TIMER OFF) that in
sequence occurs directly after the actual time will be
activated first.
caution
1 When replacing batteries, do not use old batteries or
different type batteries. Otherwise it may cause the
remote control to malfunction.
2 Remove the batteries when not being used for a long
time. Otherwise, battery leakage may damage the
remote control.
3 To prevent damage, please do not drop the
remote control.
4 The average battery life during normal use is
approximately 5 months.
The actual battery life is based on operation conditions.
Replace the batteries when there is no receiving beep
from the indoor unit or if all the indicators are shown on
the LCD window during operation.
5 Be sure there are no barriers between the remote control
and the receiver of the indoor unit otherwise the air
conditioner will not work appropriately.
6 Keep the Remote Control away from all liquids.
7 Protect the Remote Control from high temperatures and
exposure to radiation.
8 Keep the indoor receiver out of direct sunlight or the Air
Conditioner may be out of control.
9 Keep the remote control away from EMI (Electro-
Magnetic Interference) supplied by other household
appliances.
IMPORTANT: The time will be registered within a 0.5 second
period (after pressingthe TEMP/TIME button),
so you should continue pressing the button
until thedesired time is established. Otherwise
you must repeat the steps again.
Example:
To start the air conditioner at 6:00 a.m.
1 Press the CLOCK/TIMER button, the TIMER ON indicator
illuminates and the setting time flashes (if the displayed
time is just 6:00, 3 seconds later, the TIMER ON function
will be activated automatically).
2 Use the TEMP/TIME button to display"6:00" on the
TIMER ON display of the remote control.
3 Wait for 3 seconds and the setting time stops flashing
and this function is activated. The area reverts back to
displaying the clock time.
Stop
On
23:00
Combined timer
(Setting both ON and OFF timers simultaneously)
TIMER OFF
TIMER ON
(On
Stop
Start operation)
This feature is useful when you want to stop the air
conditioner after you go to bed, and start it again in the
morning when you wake up or when you return home.
Example:
Now it is 20:00 o'clock in the evening. You want to stop the
air conditioner at 23:00 and start it again the next morning
at 6:00.
1 Press the CLOCK/TIMER button until the TIMER OFF
indicator displays and time setting flashes.
2 Use the TEMP/TIME button to display "23:00" besides
the TIMER OFF display.
3 Press the CLOCK/TIMER button again to display the
TIMER ON indicator .
4 Use the TEMP/TIME button to display "6:00" besides
the TIMER ON display.
5 Wait for 3 seconds and the setting time stops flashing
and this function is activated. The area reverts back to
displaying the clock time.
On
Stop
23:00
6:00
Start
LED display panel on indoor device
NOTE: The display panel of the indoor unit may look like one
of the following:
1 Auto indicator
This indicator illuminates when the air conditioner is in
AUTO operation.
3 Defrost indicator
(For Reverse Cycle models):
This indicator illuminates when the air conditioner starts
defrosting automatically or when the warm air control
feature is activated in heating operation.
3
Temperature indicator
Displays the temperature settings when the air
conditioner is operational.
Displays the malfunction code (For ≥21000Btu/h
models only).
4
Operation indicator
This indicator illuminates when the air conditioner is
in operation.
5 Timer indicator
This indicator illuminates when Timer is set ON/OFF.
Signal receptor
1
2 3
4
5
Frequency
Auto Timer Def.
Au to
T im e r
Ope ra ti on
Airflow direction control
• Adjust the air flow direction properly. Otherwise it might
cause discomfort or cause uneven room temperatures.
• Adjust the horizontal louver using the remote control.
• Adjust the vertical louver manually.
•
To set the vertical air flow (Up-Down) direction
• Perform this function while the unit is in operation.
Keep pressing the aim button on the remote control to
move the louver to the desired direction. The readjusting
angle of the horizontal louver is 6 degrees for each press.
Range
Up and down