Electronic entry device installation instructions for basic and gard series.
Table of contents general information ........................................................................................................................................................................... 1 entry device mounting templates ...........................................................
(p/n)762.128 rev e • 08/15 © copyright 2009-2015 kaba mas llc page 1 in order to maintain the highest quality standards and ensure a problem-free application, please read this guide thoroughly before mounting the input unit. The installation instructions are the basis for security agency approvals. ...
(p/n)762.128 rev e • 08/15 © copyright 2009-2015 kaba mas llc page 2 dial ring/front housing base mounting template.
(p/n)762.128 rev e • 08/15 © copyright 2009-2015 kaba mas llc page 3 8130 entry device mounting template do not scale.
(p/n)762.128 rev e • 08/15 © copyright 2009-2015 kaba mas llc page 4 the 3000, 3715 and 4715 entry devices are designed with keyhole slots for ease of mounting and battery replacement. 1. Install the two #8-32 shoulder screws (us) or the m4-0.7 shoulder screws (metric) to mount the entry device to t...
(p/n)762.128 rev e • 08/15 © copyright 2009-2015 kaba mas llc page 5 swing bolt 1. Mount the dial plate (p/n 2676) centered on the through hole. Attach the dial plate with the two mounting screws us 8-32 (us) or the m4-0.7 (metric), and the shoulder bushings (p/n 2618). 2. Slide the bearing plate (p...
(p/n)762.128 rev e • 08/15 © copyright 2009-2015 kaba mas llc page 6 installing batteries the 3035/3125 entry device required either a battery box (2788 or 4001), or a battery/alarm box (2789 or 4002) to provide power to the lock. Mount the battery box inside the safe, and connect the cable coming f...
(p/n)762.128 rev e • 08/15 © copyright 2009-2015 kaba mas llc page 7 the 3710 entry device comes with the mylar portion of the keypad unattached. 1. Feed the key pad cable through the spindle cable hole from the front of the safe door. (figure 5). 2. Position the entry device over the screw holes on...
(p/n)762.128 rev e • 08/15 © copyright 2009-2015 kaba mas llc page 8 swing bolt 1. Mount the dial plate (p/n 3752) centered on the through hole (figure 6). Attach the dial plate with the two mounting screws us 8-32 (us) or the m4-0.7 (metric). 2. Slide the bearing plate (p/n 2674) over cable and pre...
(p/n)762.128 rev e • 08/15 © copyright 2009-2015 kaba mas llc page 9 dead bolt/spring bolt 1. Mount the dial plate (p/n 3752) centered on the through hole (figure 6). Attach the dial plate with the two mounting screws us 8-32 or the m4-0.7 (metric) making sure to rotate the dial plate counter clockw...
(p/n)762.128 rev e • 08/15 © copyright 2009-2015 kaba mas llc page 10 battery installation 1. If installed, remove black plastic battery compartment cover (located at the bottom of the keypad) by gently pulling downward on its handle. 2. Allow the battery connector and its attached leads to drop dow...
(p/n)762.128 rev e • 08/15 © copyright 2009-2015 kaba mas llc page 11 the holes required to mount the knob need to be drilled 1.25" apart and must be centered over the spindle hole. 1. To install the knob assembly, remove the insert from the front of the knob. 2. Cut the spindle to a length of .820"...