Summary of Lotus-13 LK
Page 1
Instrustion manual 2014.05 rev.1.
Page 2
1 ■at the beginning Ｐ０１ ┗ contents Ｐ０１ ■before you use Ｐ０２ ┣ characteristic of the machine, meaning of signs Ｐ０２ ┣ attention Ｐ０３ ┣ confirmation of attachment, all labels of the machine Ｐ０４ ┗ suitable installation place Ｐ０５ ■name of each parts of the machine Ｐ０６ ┗ front of the mahcine, back of the ma...
Page 3
2 it shows that the risk of smoke or fire by incorrect handling. It shows that the risk of electric shock by incorrect handling. Be sure for this machine not to get wet with water. Be sure not to touch the machine with wet hands for safety. Be sure not to break up the machine for safety. It indicate...
Page 4
3 turn off the power switch for safety and disconnect the power plug when moving the machine. Do not install on the place where direct sunlight or light of fluorescent lamp strikes. Cover the machine with cloth for rubber of rollers not to deteriorate when you are not in using. Raise the top roller ...
Page 5
4 power code machine the body, parts of the following accessories are included. If these attachments has insufficient, please contact your dealer or sales office of your nearest. Attachments.
Page 6
5 ① be sure to confirm temperature decrease and machine status for you to turn off the power. ② turn off the machine. ③ unplug the power plug from the outlet and remove the power code from the body. In the case of moving ④ move the machine with holding firmly by both hands. ※after lamination the mac...
Page 7
6 laminated material is feeded. Film exit main power switch power switch insert power plug power plug inlet back of the machine you can adjust temperature and velocity. Setting will be displayed in lcd panel. Operation panel insert paper material with laminate film. Film entry body cover transparent...
Page 8
7 each button switch recorded temperature and velocity. Default setting of 1 button is 100°c velocity 7, 2 button is 100°c velocity 5. When you record setting, press 1 button or 2 button for a second to switch setting mode, and enter temperature and velocity which you want to record and finally pres...
Page 9
8 do not change temperature and velocity in processing of lamination because you can not laminate adequately by non uniform heat. In the worst case winding occurs. Pressing this button reverses rotation of roller. This function is for urgent needs for example like you are winded by rollers. ⑩ reb bu...
Page 10
9 100µ / 150µ / 200µ / 250µ approximate total thickness = [ 100µ ] + [ thickness of paper ] + [ 100µ ] thickness means one side thickness of one pair of lamination film. In case of 100µ film, total thickness of laminated material is below. Thickness of lamination film for this machine below. Several...
Page 11
10 manuscript paper（example） making of bigger size film than manuscript paper sealing face finished product ■custom size film custom size film means lamination film which is made to fit size of manuscript paper. Custom size film is 3mm ~ 5mm bigger than manuscript paper for four all sides. Custom si...
Page 12
11 when you laminate small paper, let the paper near sealing face. If paper is too small to laminate, use protective paper. Use lamination film which has 3~5mm more margin compared to paper size. Paper paper ３ｍｍ～５ｍｍ do not cut lamination film before lamination. （it may be a cause of pinching） cut it...
Page 13
12 ① push cold button to stop roller heating when you tidy up the machine. ② turn off the power switch after auto stop of rollers and fans and losing of its heat. And unplug the power plug from outlet. ③ put the machine into box when keeping. If you have no box, cover clothe over the machine to prev...
Page 14
13 laminate with adequate setting with referring to temperature and velocity p 12. Laminated film which has passed through heating roller is softened with heating. If the heat is applied lamination film more than necessary, softened film may wind itself around roller.Thin paper and lamination film n...
Page 15
14 thick paper ～３０ｃｍ ～ to ５０ｃｍ temperature：100℃ velocity：1 or 2 ● prepare thick paper like drawing paper. (some lami’s pouch lamination film has special cleaning paper) ● adequate size is 30cm×30cm ~ 50cm, adequate thickness is 250g/m2~300g/m2. ● set temperature [100 ℃ ]. ● set velocity [1] or [2] w...
Page 16
15 ●in case you use heater or projector or electric wire reel around. ●in case of overloaded. ●in case motor has strange noise. Pull the fuse box with a flathead screwdriver or the like. Please check fuse of fuse box tip is snapped or not. If fuse wire is snapped, replace it and turn on the machine ...
Page 17
16 ●document is not too thick? Do not laminate too thick document. It may be a cause of failure. Adjust velocity setting if setting is [0]. ●document is wrapped around the roller? Press reverse button to pull documents if it remains in film entry. Do not pull it forcedly. It may be a cause of failur...
Page 18
17 ※ details in this document can be changed without notice to make improvements on the product. Max.Laminating width max.Pouch thickness max.Laminating speed roller heating heating method power requirements power consumption size (w x d x h) weight warm-up time machine name a2 size（480 mm ） 690×271...