Lanier R/C MARINER 40 MK II ARF Assembly Manual

Manual is about: Stinger II .46 ARF

Summary of MARINER 40 MK II ARF

  • Page 1

    Lanier rc shrike 40 warning! This is not a toy! This is not a beginners airplane this r/c kit and the model you will build from it is not a toy! It is capable of serious bodily harm and property damage. It is your responsibility, and yours alone - to build this kit correctly, properly install all r/...

  • Page 2: Shrike 40

    Lanier - shrike 40 - instructions page 2 copyright 1998 - lanier r/c such sale, or there after be barred. This one year limitation is imposed by agreement of the parties as permitted by the laws of the state of georgia. Shrike 40 building instructions the shrike 40 is a fun and exciting airplane, en...

  • Page 3

    Lanier - shrike 40 - instructions page 3 copyright 1998 - lanier r/c it is perpendicular to the side. It is important that both of these formers be installed as described. 3. Place the other side with its slots in each former, with the top side up. Using a square on a flat surface, make sure the sid...

  • Page 4

    Lanier - shrike 40 - instructions page 4 copyright 1998 - lanier r/c from the hole. Now glue in the remaining two servo mounting rails. Note: gluing in the servo rails at this time will prevent the sides from bowing out when pulling them together at the front. 11. Locate the firewall f2 and layout t...

  • Page 5

    Lanier - shrike 40 - instructions page 5 copyright 1998 - lanier r/c locate fl with the engine crankshaft, with the spinner backplate mounted on the engine, and glue in place. 20. Now round off the nose to fl. So that you don't round off too far back it is a good idea to lay rib rl in position and t...

  • Page 6

    Lanier - shrike 40 - instructions page 6 copyright 1998 - lanier r/c 5. Now slide ribs r2, r3, r4 and r5 the spars of one wing, roughly positioning them. 6. Place the fuselage against the side of the work bench with the rib tabs resting on the surface over the plans. Some small weights on the spars ...

  • Page 7

    Lanier - shrike 40 - instructions page 7 copyright 1998 - lanier r/c 15. Using the 3/32” sheet cut from the le, sheet between ribs r1 and r2. To use 2 aileron servos, first install two ¼” x 6-1/4” hardwood rails across the rib bay in the notches, then sheet the bottom wing as shown on the plans. Cut...

  • Page 8

    Lanier - shrike 40 - instructions page 8 copyright 1998 - lanier r/c 6. Locate the 3/16" sheet g1 gussets and glue in place as shown on the plans. 7. Cut a piece 11-3/8” from the 3/8” x 2-1/4" x 12" trailing edge stock. Shape the ends to the configuration shown on the plans. Sand the angles shown on...

  • Page 9

    Lanier - shrike 40 - instructions page 9 copyright 1998 - lanier r/c 5. Assuming that the fuselage is painted or covered, peel off one side of the tape supplied. Locate one end of the tape at the back edge of the nose block. Place the rest down the center of the fuselage towards the tail. Now pull o...

  • Page 10

    Lanier - shrike 40 - instructions page 10 copyright 1998 - lanier r/c 4. Turn on the radio with the engine running to make sure there are no intermittent glitches. Give it a good range check. 5. Check all hardware to be sure it is secure. There is nothing worse than losing an airplane on the first f...

  • Page 11

    Lanier - shrike 40 - instructions page 11 copyright 1998 - lanier r/c material list fuselage 1 (1) - bagged parts (laser cut fl,f2 formers, sheer webs) 2 (2) - sheet 1 (laser cut fuselage sides fsla) 3 (1) - sheet 2 (laser cut fuselage sides fs1b and formers) 4 (2) - 3/32" x 3 x 36" balsa sheet (top...

  • Page 12

    Lanier - shrike 40 - instructions page 12 copyright 1998 - lanier r/c hardware and material list for shrike 40 general 1 4-5 channel radio with 3-4 servos 2 recommended engine - standard sport .40 (if larger than a .40, nose will have to be lengthened to suit) 3 muffler - to suit engine size 4 fuel ...

  • Page 13

    Lanier - shrike 40 - instructions page 13 copyright 1998 - lanier r/c.