- DL manuals
- Magicar
- Car Alarm
- M871A
- Installation Manual
Magicar M871A Installation Manual
Summary of M871A
Page 1
Magicar m871a car alarm with two-way remote installation guide 1.
Page 2: Magicar M871A
2 magicar m871a car alarm with two-way remote installation guide.
Page 3
Table of contents i. Introduction............................................................................................................................ 4 ii. Placing....................................................................................................................................
Page 4: I. Introduction
En i. Introduction magicar m871a is a safety device with the highest level of security. Thanks to the 2- way remote with pager you will be immediately informed about possible car intrusion, as well as the manner of the intrusion even though you are too far from the car to hear the siren. The biggest...
Page 5
En warning! ¾ when installing a door contact, you must find an appropriate wire from the wire bundle of a car (it is important from the security point of view as well as that of remote starting) ¾ wiring used for the alarm connection must not be broken nor its insulation damaged. This should prevent...
Page 6: IV. Wiring Arrangement
87 30 87a 85 86 line a line b +12v impuls (-) if you want to connect shortly two wires by (-) signal. E.G.: mostly used for installing alarm gas relays. Iv. Wiring arrangement 6 connector 1 – cn1 1 – red - +12v power supply - power supply, connect to +12v. 2 –red/white – lights -this is a line for l...
Page 7
En en starter-blocking connection: after cutting car starter lines, you have to connect lines to the relay outputs used to block the starter. 2 – green - ignition input - connect to the switchboard (to the +12v wire when ignition on). 3 – red/black - negative door switch input ( - ) 4 – red - positi...
Page 8
- led indication connector 9 - white - rps sensor 8 - shock sensor connector 10 - red 3 – red - power supply of +12 v 4 – yellow - shock sensor input – first level (-) 1 – black - grounding 2 – white - shock sensor input – second level (-) - additional sensor connector 11 - green 1 – black - groundi...
Page 9
En note: • if you want to carry out any other changes, start the whole process over again. • if you hear a long beep, you are out of programming menu area. Start again by the step 1. Failure notice: if the remote happened to be out of the range when programming changes, it will display „fail“ notice...
Page 10
En options no. Function button i button ii button iii button iv 2-01 trunk output time 0.5 sec 2 sec 3 sec 4 sec 2-02 door lock impulse 0.8 sec 4 sec 2 x 0.8 sec 15 sec 2-03 door unlock impulse 0.8 sec 4 sec 2 x 0.8 sec - 2-06 parking lights normal mode continuous mode pulse mode - 2-08 aux 1 0.5 se...
Page 11: Vii. Valet Mode
En and the pulse mode (mode 2). Output - lights mode 1 – continuous lights - flashing mode 2 – pulse lights control unit relay contact bypassing the hazard light switch light output (cn1-3 or 4) common input (cn1-2) hazard lights switch fig.1 parking lights output connected to the hazard switch cali...
Page 12: Remote Control Programming
Entering valet mode with pin code. 1. Armed. 2. By opening the door, the alarm will be triggered. Siren will chirp. 3. Within 3 sec turn the ignition on/off three times. 4. Lights will flash once. 5. Push the button on rps as many times, as your first number is. Intervals between the click/pushes mu...
Page 13
En en programming of security code (1111-9999): 1. Ignition on. 2. Open the door. 3. Push the button on rps sensor 10 times. At every single click, led will flash red once. Intervals between the click/pushes must not be longer than 1.5 sec. 4. Blue led will start flashing rapidly. If it does not hap...
Page 14
C o nt a c t - lo ck ed con tact - u n loc ked yellow/black yellow yellow/white green/black green/white green nc1 nc2 com1 no1 com2 no2 original built-in control unit. L o c k e d grou nd u n lo c k e d fig.4 original built-in central power lock cn2 fig.3 original built-in central power lock & using...
Page 15: Wiring Diagram Magicar M871A
En +12v 2 when signal light wire is connect to + - + - then common wire - + magicar 7 gray/black 6 orange 5 orange/black 4 red 3 red/black 2 green 1 violet rps sensor shock sensor led signaling 12v constant light (no) trunk trigger input (-) light (com) siren fuse 5a parking light input (+) parking ...
Page 16
16 - the car alarm system is designed for fitting into all kinds of cars with petrol and diesel engines with +12v volatge finished by a negative pole. - car alarm must be fitted following manufacturer‘s recommendation. - the alarm installation to be carried out only by authorised service centre. - c...