Magnavox MSB5660 Owner's Manual - Troubleshooting Guide
– 18 –
Troubleshooting Guide
If the Unit does not perform properly when operated as instructed in this Owner’s Manual, refer to the following.
INFORMATION
Problem
Corrective action
No Power (no LED lights will be seen)
–
Check if the AC Power cord is properly connected.
–
Unplug the AC outlet once, and wait for 15-20 seconds and then plug it in again.
No Sound
–
Make sure both the TV or other devices and the Soundbar are Turned On.
–
Confirm the connections to the TV or the device are made properly as shown in CONNECTIONS.
(Refer to “CONNECTIONS” on page 9)
–
Press the
INPUT
source buttons on your Soundbar’s Remote Control for the correct audio input.
–
Confirm that the Soundbar is not muted. Press
VOL +/-
to unmute the sound.
(Refer to “Adjusting the Volume” on page 12)
–
For optical audio connection, select another audio signal on the connected external device.
(This product supports Dolby Audio and PCM.)
–
Depending on the usage and usage environment, chatter sound and distorted sound may be generated.
To reduce such sounds, lower the volume.
–
If Input is Optical Sound make sure that the Optical cable Connector is completely inserted into the
Terminal (Click Sound heard when properly inserted).
No Sound from the Subwoofer or
the Satellite speakers
–
Check if
PAIRING
indicator on the rear of Subwoofer is lit.
–
Confirm that all speakers and the Subwoofer is outputting the sound by the Speaker check.
(Refer to “Confirming the Sound Output from the Speakers” on page 14)
–
If the Satellite speakers are not emitted the sound, press
on the Remote Control to set
surround sound to On. Only select sounds are played from the satellite speakers. This is normal.
Distorted sound
–
Adjust the sound settings of the connected device.
–
Decrease the volume on the connected Bluetooth compatible Device.
Abnormal noise is generated.
–
Be sure each cables are plugged in all the way.
No reaction to the Remote Control.
–
Confirm that the Soundbar AC Power cord is plugged into an AC outlet.
–
Check the batteries in the Remote Control, and make sure they are inserted properly by + or - symbols.
–
Aim the remote at the center of this Unit.
–
If the Remote Control does not work and all LED’s of the Soundbar stay lit for over 30 seconds, there is a
failure in the electrical system. Unplug the AC Power cord and contact the service center.
–
Use a Digital or Phone Camera pointing the Remote Control at the Camera Lens and press any Remote
button. If Remote IR LED(s) flash on Camera Display, then the Remote is Transmitting a Signal. Some
Phone Cameras have IR filters in their Lens, therefore you will not see the IR LED(s) flash.
An external device cannot connect
with the Soundbar via Bluetooth.
–
Confirm that the external device is compatible with the audio signals supported by the Soundbar.
–
Confirm that Bluetooth is enabled on the external device.
See the user Manual of the external device on how to enable Bluetooth.
–
If reconnecting the Bluetooth compatible Device to the Soundbar fails, delete the registered profile
of this Soundbar from the Bluetooth compatible Device, then perform pairing again. This Unit can
store up to 8 device profiles.
–
Another Bluetooth compatible Device is already connected to the Soundbar. Disconnect the
connected device, then try again.
Poor sound quality from the
connected Bluetooth compatible
Device.
–
The Bluetooth reception may be poor. Confirm that there is no obstacle between the Bluetooth
compatible Device and the Soundbar. If this does not improve the sound quality, move the Bluetooth
compatible Device closer to the Soundbar.
Unstable connection between the
Bluetooth compatible Device and
the Soundbar.
–
The Bluetooth reception may be poor. Confirm that there is no obstacle between the Bluetooth
compatible Device and the Soundbar. If this does not improve the sound quality, move the Bluetooth
compatible Device closer to the Soundbar.
Specifications
Output Power
Total:
160W (Peak at THD+N
Main unit:
72W (24W x 3)
Satellite speaker:
24W (12W x 2)
Subwoofer:
64W
Product Dimensions
Main unit:
W:
39.4 inches (999 mm) /
H:
3.1 inches (77 mm) /
D:
3.1 inches (77 mm)
Satellite speaker:
W:
3.1 inches (77 mm) /
H:
6.0 inches (150 mm) /
D:
3.1 inches (77 mm)
Subwoofer:
W:
8.4 inches (211 mm) /
H:
10.1 inches (255 mm) /
D:
8.4 inches (211 mm)
Product weight
(net)
Main unit:
5.5 lbs. (2.5kg)
Satellite speaker:
2.2 lbs. (1.0kg) [1.1 lbs. (0.5kg) x 2]
Subwoofer:
6.8 lbs. (3.1kg)
Input
USB input (File system: FAT32, File format: WAV)
Coaxial
input
Optical
input
Line
input
Auxiliary
input
Bluetooth
Profile:
A2DP, AVRCP
Version:
2.1+EDR
Optical / Coaxial Input
Dolby Digital / PCM
48kHz 16bit Max.
• Designs and Speci
fi
cations are subject to change without notice.
• If there is a Discrepancy between Languages, the default Language will be English.