1 english ( o rigina l in st ruct ions) instruction manual important: read before using. Cordless circular saw dhs680 015156.
2 english (original instructions) specifications model dhs680 blade diameter 165 mm at 0° 57 mm at 45° 41 mm max. Cutting depth at 50° 37 mm no load speed 5,000 min -1 overall length 350 mm net weight 3.3 kg rated voltage d.C. 18 v • due to our continuing program of research and development, the spe...
3 they are manufactured in accordance with the following standard or standardized documents: en60745 the technical file in accordance with 2006/42/ec is available from: makita, jan-baptist vinkstraat 2, 3070, belgium 18.3.2014 000331 yasushi fukaya director makita, jan-baptist vinkstraat 2, 3070, be...
4 18. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 19. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing acc...
5 kickback causes and related warnings − kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator; − when the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the mot...
6 19. Check the operation of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a build-up of debris. 20. Lower guard may be retracted manually only for special ...
7 32. Only use the saw blade with the diameter that is marked on the tool or specified in the manual. Use of an incorrectly sized blade may affect the proper guarding of the blade or guard operation which could result in serious personal injury. 33. Keep blade sharp and clean. Gum and wood pitch har...
8 functional description caution: • always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 1 2 3 015120 caution: • always switch off the tool before installing or removing of the ba...
9 battery indicator status remaining battery capacity 50% - 100% 20% - 50% 0% - 20% charge the battery on off blinking 015146 automatic speed change function 1 015144 mode indicator status operation mode high speed mode high torque mode 015137 this tool has "high speed mode" and "high torque mode". ...
10 bevel cutting 1 015105 loosen the front lever. Set for the desired angle (0° - 50°) by tilting accordingly, then tighten the front lever securely. 1 0-45 0-50 015116 use the 45° stopper when you do precise 45° angle cutting. Turn the stopper counterclockwise fully for bevel cut (0° - 45°) and tur...
11 1 2 4 3 015108 to remove the blade, press the shaft lock so that the blade cannot revolve and use the wrench to loosen the hex bolt clockwise. Then remove the hex bolt, outer flange and blade. 1 2 4 3 015109 to install the blade, follow the removal procedure in reverse. Be sure to tighten the hex...
12 connecting a vacuum cleaner (for european countries only) 1 2 015111 1 2 015112 when you wish to perform clean cutting operation, connect a makita vacuum cleaner to your tool. Install the dust nozzle on the tool using the screw. Then connect a hose of the vacuum cleaner to the dust nozzle as show...
13 adjusting for accuracy of 0 ° and 45° cut (vertical and 45 ° cut) 1 2 015113 1 0 45 015114 this adjustment has been made at the factory. But if it is off, adjust the adjusting screws with a hex wrench while inspecting 0° or 45° the blade with the base using a triangular rule or square rule, etc. ...
14.
15.
16 www.Makita.Com makita jan-baptist vinkstraat 2, 3070, belgium makita corporation anjo, aichi, japan 885374a224.
