- DL manuals
- Makita
- Tool Storage
- LS0714
- Instruction Manual
Makita LS0714 Instruction Manual
Summary of LS0714
Page 1
1 english ( o rigina l in st ruct ions) instruction manual double insulation important: read before using. Slide compound saw ls0714 ls0714f ls0714fl ls0714l 005515.
Page 2: Specifications
2 english (original instructions) specifications model ls0714/ ls0714f/ ls0714fl/ls0714l blade diameter 190 mm blade body thickness 1.3 mm - 2.0 mm hole (arbor) diameter 20 mm max. Miter angle left 47° , right 57° max. Bevel angle left 45°, right 5° max. Cutting capacities (h x w) with blade 190 mm ...
Page 3
3 ene006-1 intended use the tool is intended for accurate straight and miter cutting in wood. With appropriate saw blades, aluminum can also be sawed. Enf002-2 power supply the tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated...
Page 4: Additional Safety Rules
4 4. Keep children away. Do not let visitors touch the tool or extension cord. All visitors should be kept away from work area. 5. Store idle tools. When not in use, tools should be stored in a dry, high or locked up place, out of reach of children. 6. Do not force the tool. It will do the job bette...
Page 5: Save These Instructions.
5 6. Turn off tool and wait for saw blade to stop before moving workpiece or changing settings. 7. Unplug tool before changing blade or servicing. 8. Always secure all moving portions before carrying the tool. 9. Stopper pin which locks the cutter head down is for carrying and storage purposes only ...
Page 6: Installation
6 installation bench mounting when the tool is shipped, the handle is locked in the lowered position by the stopper pin. Release the stopper pin by lowering the handle slightly and pulling the stopper pin. 1 003923 this tool should be bolted with two bolts to a level and stable surface using the bol...
Page 7
7 immediately. Check to assure spring loaded return action of guards. Never use the tool if the blade guards or spring are damaged, faulty or removed. Doing so is highly dangerous and can cause serious personal injury. If the see-through blade guard becomes dirty, or sawdust adheres to it in such a ...
Page 8
8 with the tool unplugged, rotate the blade by hand while holding the handle all the way down to be sure that the blade does not contact any part of the lower base. Re-adjust slightly, if necessary. Warning: • after installing a new blade, always be sure that the blade does not contact any part of t...
Page 9
9 so that it is slightly above the level. Secure the lever with the screw firmly. Switch action caution: • before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "off" position when released. • when not using the tool, remove the lock-off button...
Page 10: Assembly
10 • laser radiation, do not stare into the beam or view directly with optical instruments, class 2m laser product. To turn on the laser beam, press the upper position (i) of the switch. Press the lower position (o) to turn off. Laser line can be shifted to either the left or right side of the saw b...
Page 11
11 1 2 3 4 012586 press the shaft lock to lock the spindle and use the hex wrench to loosen the hex socket bolt clockwise. Then remove the hex socket bolt, outer flange and blade. 1 2 3 4 5 012587 to install the blade, mount it carefully onto the spindle, making sure that the direction of the arrow ...
Page 12
12 1 2 3 006792 1 2 006794 securing workpiece warning: • it is extremely important to always secure the workpiece properly and tightly with the vise. Failure to do so can cause the tool to be damaged and/or the workpiece to be destroyed. Personal injury may also result. Also, after a cutting operati...
Page 13: Operation
13 the maximum width of the workpiece which can be secured by the horizontal vise is 120 mm. Caution: • grip the workpiece only when the projection is at the topmost position. Failure to do so may result in insufficient securing of the workpiece. This could cause the workpiece to be thrown, cause da...
Page 14
14 2. Slide (push) cutting (cutting wide workpieces) 2 1 005525 loosen two clamp screws which secure the slide poles counterclockwise so that the carriage can slide freely. Secure the workpiece with the vise. Pull the carriage toward you fully. Switch on the tool without the blade making any contact...
Page 15
15 miter angle left and right 45 right 50 right 55 right 57 bevel angle left 0 - 45 left 0 - 40 left 0 - 30 left 0 - 25 006393 when performing compound cutting, refer to "press cutting", "slide cutting", "miter cutting" and "bevel cut" explanations. 6. Cutting crown and cove moldings crown and cove ...
Page 16
16 molding position in fig. A molding edge against guide fence (1) for outside corner for inside corner finished piece (2) (3) (4) table (b) finished piece will be on the left side of blade. Finished piece will be on the right side of blade. Wall contact edge should be against guide fence. Wall cont...
Page 17: Maintenance
17 10. Groove cutting 1 001563 a dado type cut can be made by proceeding as follows: adjust the lower limit position of the blade using the adjusting screw and the stopper arm to limit the cutting depth of the blade. Refer to "stopper arm" section described on previously. After adjusting the lower l...
Page 18
18 side of the blade with the face of the guide fence using a triangular rule, try-square, etc. Then securely tighten the hex socket bolt on the guide fence in the order from the right side. 1 002209 make sure that the pointer points to 0° on the miter scale. If the pointer does not point to 0°, loo...
Page 19
19 adjusting the position of laser line for model ls0714fl, ls0714l 1 2 3 005701 1 2 005702 warning: • as the tool is plugged when adjusting the position of laser line, take a full caution especially at switch action. Pulling the switch trigger accidentally cause an accidental start of the tool and ...
Page 20
20 replacing fluorescent tube for model ls0714f, ls0714fl only 1 2 3 4 1 5 002028 caution: • always be sure that the tool is switched off and unplugged before replacing the fluorescent tube. • do not apply force, impact or scratch to a fluorescent tube, which can cause a glass of the fluorescent tub...
Page 21: Optional Accessories
21 clean according to the directions in the previously covered section titled "blade guard". Lubricate the sliding portions with machine oil to prevent rust. • when storing the tool, pull the carriage toward you fully so that the slide pole is thoroughly inserted into the turn base. To maintain prod...
Page 22
22.
Page 23
23.
Page 24
24 makita corporation anjo, aichi, japan www.Makita.Com 884547h226.