Mediterranean Tan MediterraneanTan Ultra Instruction Manual - page 7
7
3. Prepare the Micro-intel Spray Gun cont’d
1. Follow the diagram to prepare the Spray Gun
a. Unscrew the plastic cup from the Micro-intel Spray Gun. Pour tanning solution into the cup. Do not fill more than ¾
full.
b. Carefully screw the cup back onto the main body of the Micro-intel Spray Gun. Screw the cup on firmly but
DO NOT
over tighten. Over tightening will cause the cup to “pop” and damage the threads. Leakage can
then occur requiring replacement of the cup.
c. Look at Mist Applicator Patterns diagram below. Note the position of the directional flow and the direction of the
spray pattern. Pattern 1 is for spraying across from side to side. Pattern 2 is for spraying up and down. Pattern 3
will produce a spot or circle. Patterns 1 and 2 are the most common positions for applying tanning solutions.
d. Turn the Directional Flow to the position you want.
2. Next, position the Mediterranean Tan™ Ultra unit as far away as practical and possible from the area where you will be
spraying.
3. Attach the remaining end of the hose to the Micro-intel Spray Gun as follows:
a. Locate the male connection at the rear top of the Micro-intel Spray Gun. See figure 8.
b. Allign 2 nibs of the black connector on the air hose with the grooves in the Micro-intel Spray Gun and slide in.
Fig
8
c. Gently turn air hose clockwise to lock in place .
d. Your Micro-intel Spray Gun should now be firmly attached to the air hose.
7
3
Prepare the T6050 Spray Gun cont’d.:
1. Follow the diagram to prepare the Spray Gun
a. Unscrew the plastic cup from the Spray Gun. Pour tanning solution into the cup. Do not fill more than ¾ full.
b. Carefully screw the cup back onto the main body of the Spray Gun. Screw the cup on firmly but
DO NOT
over tighten. Over tightening will cause the cup to “pop” and damage the threads. Leakage can
then occur requiring replacement of the cup.
c. Locate the air cap (#2) on the T6050 diagram. Slightly turn the air cap ring (#1) anti or counter clockwise
to loosen the air cap. Notice that you can now rotate the air cap freely.
d. Look at Mist Applicator Patterns diagram below. Note the position of the air cap and the direction of the
spray pattern. Pattern 1 is for spraying across from side to side. Pattern 2 is for spraying up and down.
Pattern 3 will produce a spot or circle. Patterns 1 and 2 are the most common positions for applying
tanning solutions.
e. Turn the air cap (#2) to the position you want. Turn the air cap ring (#1) clockwise to lock the air cap in
place.
SPRAY GUN PATTERNS
1. Misting across from side to side
2. Misting up and down.
3. Misting in a spot or circle
1. Next, position the Turbo Unit as far away as practical and possible from the area where you will spray.
2. Attach the remaining end of the hose to the T6050 Spray Gun as follows:
a. Locate the coupler at the rear top of the T6050 Spray Gun. See T6050 diagram.
b. Pull back on the collar of the black connector on the air hose.
c. Push the connector over the coupler and release. Figure 7.
d. Your Spray Gun should now be firmly attached to the air hose.
5
2
Set up and operate your PRINCESS
Tanning System:
1. Plug the PRINCESS
tanning system unit into a proper electrical outlet. Make sure that the electric current
you are connecting to is the same as your unit. (110v or 220v). DO NOT attempt to connect the unit to the wrong
electric current as this will not only damage your unit but also void your warranty.
2. Next, locate the male end of the air hose and connect it to the female quick connect on the PRINCESS
tanning system.
a. To insert the coupler pull back on the ring of the black coupler located on the PRINCESS
tanning
system and connect it to the male connector on the hose. Figure 6.
Fig. 6
b. Release the ring to allow the coupler to snap into place. The hose should now be connected to the
unit Figure 7.
Fig. 7
c. To remove the air hose, pull back on the ring of the black coupler and remove
If you have just finished spraying, the connector may be hot. Allow the PRINCESS unit to cool down
or about 10 minutes before disconnecting the air hose from the turbo unit. Use Caution!