(revised 2010-11-15) 1 102mc industrial media converter user manual & installation guide.
(revised 2010-11-15) 2 industrial media converter installation guide 102mc the 102mc is a 2 port unmanaged transparent media converter that converts 10base-t copper to 10base-fl half duplex fiber..
(revised 2010-11-15) 3 copyright, © n-tron corp., 2008 820 s. University blvd., suite 4e mobile, al usa 36609 all rights reserved. Reproduction, adaptation, or translation without prior written permission from n-tron corp. Is prohibited, except as allowed under copyright laws. Ethernet is a register...
(revised 2010-11-15) 4 environmental safety warning: disconnect the power and allow to cool 5 minutes before touching. Electrical safety warning: disconnect the power cable before removing the enclosure top. Warning: do not operate the unit with the top cover removed. Warning: properly ground the un...
(revised 2010-11-15) 5 package contents please make sure the serial over ethernet package contains the following items: 1. 102mc media converter 2. Product cd contact your carrier if any items are damaged. Installation read the following warning before beginning the installation: warning never insta...
(revised 2010-11-15) 6 din-rail mounting install the unit on a standard 35mm din-rail. Recess the unit to allow at least 5” of horizontal clearance for the fiber optic cable bend radius. To install the unit to 35mm industrial din-rail, place the top edge of the included mounting bracket on the back ...
(revised 2010-11-15) 7 front panel from top to bottom: green led lights when power is connected rj45 port 10base-t connection act activity led for fiber optic port lnk link led for fiber optic port rx fiber optic receiver port tx fiber optic transmitter port. Note: the rj45 data port has two led’s l...
(revised 2010-11-15) 8 applying power (top view) unscrew & remove the dc voltage input plug from the power input header install the dc power cables into the plug (observing polarity). Plug the voltage input plug back into the power input header. Tightening torque for the terminal block power plug is...
(revised 2010-11-15) 9 n-tron switch grounding techniques the grounding philosophy of any control system is an integral part of the design. N-tron switches are designed to be grounded, but the user has been given the flexibility to float the switch when required. The best noise immunity and emission...
(revised 2010-11-15) 10 rj45 connector crimp specifications please reference the illustration below for your cat5 cable specifications:.
(revised 2010-11-15) 11 connecting the unit for the 10base-fl fiber optic port, remove both of the dust caps from the fiber optic connectors and connect the fiber optic cables. The tx port on the local unit should be connected to the rx port of the far end device, and the rx port should be connected...
(revised 2010-11-15) 12 support contact n-tron corp. At: tel: 251-342-2164 fax: 251-342-6353 www.N-tron.Com n-tron_support@n-tron.Com fcc statement this product complies with part 15 of the fcc-a rules. Operation is subject to the following conditions: (1) this device may not cause harmful interfere...
(revised 2010-11-15) 13 key specifications physical height: 3.49" width: 2.01" depth: 4.00" weight: 0.75 lbs din-rail: 35mm electrical redundant input voltage: 10-30 vdc (regulated) input current: 80 ma @ 24vdc (steady state) inrush current: 7.3amp/1.0ms @ 24vdc input ripple: less than 100 mv input ...
(revised 2010-11-15) 14 n-tron limited warranty n-tron, corp. Warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from n-tron or its authorized reseller....
