NAD T 747 Owner's Manual - page 9
1 DIGITAL AUDIO IN/OUT (COAXIAL 1-2, OPTICAL 1-2): Connect
to the corresponding optical or coaxial S/PDIF-format digital output
of sources such as CD or DVD players, HDTV or satellite tuners and
other components. Coaxial and Optical digital input association is
configurable via the Source Setup item of the Setup Menu OSD.
DIGITAL AUDIO OUT (OPTICAL, COAXIAL): Connect the optical or
coaxial digital OUT port to the corresponding S/PDIF digital input of a
compatible device such as CD recorders, receivers, computer soundcard
or other digital processors.
2 MONITOR (S-VIDEO, VIDEO): Connect to video input of the monitor/
television using quality dual-RCA and/or S-Video cables designed for
video signals. In general, the S-Video connection is superior and should
be used if your TV/monitor provides the corresponding input.
3 AUDIO 1 IN/OUT, VIDEO 1 IN/OUT: Connect AUDIO 1 IN/VIDEO 1 IN
to the analog audio/video output port of a recording component such
as a video cassette recorder, DVD recorder or to an outboard audio/
video processor. Connect AUDIO 1 OUT/VIDEO 1 OUT to the recording
component’s corresponding analog audio/video input port.
The signal present at AUDIO 1 OUT/VIDEO 1 OUT port is dependent
upon the current active SOURCE. There will be no output when Source
1 is the selected source input. This prevents feedback through the
recording component thereby preventing possible damage to your
speakers.
4 AUDIO 2 IN/VIDEO 2 IN, AUDIO 3 IN/VIDEO 3 IN, AUDIO 4 IN/
VIDEO 4 IN: These comprise the T 747’s other principal inputs. Connect
these S-Video, composite video, and analog stereo audio input ports
to the corresponding output ports of source components such as DVD
players and HDTV/satellite tuners. Refer also to “AUDIO 1 IN/OUT, VIDEO
1 IN/OUT” discussion above.
5 zONE 2: Sends zone selected video output source to the
corresponding video input of another zone. Use high quality patch
cables to reduce noise pickup over long distance runs. Refer also to
the item about ZONE 2 CONTROLS under the USING THE T 747 - MAIN
MENU segment of the OPERATION section.
6 HDMI (HDMI 1-4, HDMI MONITOR OUT): Connect HDMI inputs to
the HDMI OUT connectors of source components such as DVD player or
HDTV satellite/cable box. Connect the HDMI Monitor OUT to a HDTV or
projector with HDMI input.
WARNING
BeforeconnectinganddisconnectinganyHDMIcables,boththeT747
andtheancillarysourcemustbepoweredOFFandunpluggedfromthe
ACoutlet.Failuretoobservethispracticemaycausepermanentdamage
toallequipmentconnectedviaHDMIsockets.
7 COMPONENT VIDEO 1-3 IN, COMPONENT VIDEO OUT: Connect
the Component Video IN 1-3 inputs to Component Video outputs
from compatible source components, typically a DVD player and
terrestrial or satellite HDTV tuner. Connect Component Video OUT to
the Component Video input of a compatible video monitor/TV. Be
sure to observe consistency in connecting the Y/Pb/Pr jacks to the
corresponding sources/inputs. The routing of the component video
inputs is fully configurable via the Setup Menu.
The T 747’s component video inputs and outputs are fully wideband
and compatible with allowable HDTV formats.
IDENTIFICATION OF CONTROLS
REAR PANEL
ATTENTION!
PleasemakesurethattheT747ispoweredofforunpluggedbeforemakinganyconnections.Itisalsoadvisabletopowerdownorunplugallassociated
componentswhilemakingorbreakinganysignalorACpowerconnections.
1
2
3
4
6
7
8
9
10
16
18
20
17
19
5
14
13
12
11
15
22
21
8
EN
G
LIS
H
FR
A
N
Ç
A
IS
ES
PA
Ñ
O
L
IT
A
LIA
N
O
D
EU
TS
CH
N
ED
ER
LA
N
D
S
SV
EN
SK
A
РУ
СС
К
И
Й