NAIM AV2 Owner's Manual - page 10
8
7.7.4 Pro Logic II Options
Note:
Function only available with AV2 connected.
Selection of
Pro Logic II
Options provides adjustment of the
Panorama
,
Centre Width
and
Dimension
parameters.
Panorama
“ON” diverts a proportion of the front stereo signal to
the surround channels.
Centre Width
adjustment varies the relative strength of the
centre and front channels, a higher value increasing the strength
of the front channels.
Dimension
adjustment varies the relative strength of the
surround and front signals, a higher value increasing the strength
of the surround channels.
Note:
Pro Logic II Options are only available when Pro Logic II Music
Mode is selected.
7.7.5 Neo:6 Centre Gain
Note:
Function only available with AV2 connected.
Selection of
Neo:6 Centre Gain
provides independent
adjustment of the centre channel volume level.
Note:
Neo:6 Centre Gain is only available when DTS Neo:6 Music
Mode is selected.
7.7.6 Midnight Mode
Note:
Function only available with AV2 connected.
Selection of
Midnight Mode
compresses the audio signal
and reduces its bass content. Midnight Mode can reduce the
disturbance of late-night listening.
Note:
Midnight Mode is only available with Dolby Digital material.
7.7.7 Cine EQ
Note:
Function only available with AV2 connected.
Selection of
Cine EQ
reduces the emphasised high-frequency
sound found on some film derived programme material.
7.7.8 AV2 Input Labels
Note:
Function only available with AV2 connected.
Selection of
AV2 Input Labels
enables a descriptive label to be
assigned to each numbered AV2 signal input. Inputs can also be
disabled (set to OFF) from this menu.
Note:
If Versatile Input 1 is set to 6 or 8 channel direct, Versatile
Input 2 will not be available for selection.
7.8 Speaker Setup
Note:
Some menus only available with McC installed or AV2
connected.
Selection of
Speaker Setup
from the top level menu generates
a second level menu comprising the options listed below. These
options are only available if a
Multi-channel Card (McC)
is
installed or an
AV2 Processor
is connected.
Note:
When a DVD5 is connected to an AV2, adjustment of
Speaker Setup parameters actually adjusts AV2 functions. The
AV2 front panel or handset interface is disabled while the DVD5
on-screen menus are displayed. If the AV2 front panel or handset
interface is subsequently used to adjust any Audio Setup parameters
the DVD5 menu display will update automatically.
7.8.1 Speaker Size
Note:
Function only available with McC installed or AV2 connected.
Selection of
Speaker Size
Selection of
Selection of
enables the size of each speaker
to be defined. Generally a “small” speaker is an element of a
matched satellite/sub-woofer package, while a “large” speaker
is a stand-alone full-range type. The “small” left/right option is
unavailable if no sub-woofer is present, and the “extra surround”
option is unavailable if no surround speakers are present.
7.8.2 Distance Units
Note:
Function only available with McC installed or AV2 connected.
Selection of
Distance Units
Selection of
Selection of
enables the preferred distance
measurement units (feet or metres) for the Speaker Distance
menu to be set.
7.8.3 Speaker Distance
Note:
Function only available with McC installed or AV2 connected.
Selection of
Speaker Distance
Selection of
Selection of
enables the distance of each
speaker from the primary listening position to be defined.
Distance definition is only available for speakers previously
specified (in 7.8.1) as present.
Note:
The distances need not be defined accurately. Plus or minus
150 mm (6 inches) is adequate.
7.8.4 Test Signal
Note:
Function only available with AV2 connected.
Selection of
Test Signal
Selection of
Selection of
switches on the speaker test signal.
Ensure that the DVD5 or AV2 audio outputs and downstream
amplifiers are connected and configured appropriately. Ensure
also that the downstream amplifiers are switched on.
Note:
If the test signal is either too loud or too quiet it can be
adjusted with the DVD5 or AV2 handset volume up (
5
) or down
(
6
) keys.
7.8.5 Speaker Level Adjustment
Note:
Function only available with AV2 connected.
Selection of
Speaker Level Adjustment
after switching on
the
Test Signal
enables subjective matching of the volume
level of each speaker channel. Select each speaker channel in
turn and adjust the volume until the loudness of each sounds
approximately the same.
Note: The AV2 section of this manual provides further guidance on
the adjustment of relative volume levels.
7.9 Parental Control Setup
The
Parental Control
menu enables a
pass code
to be set in
order to restrict access to unsuitable programme material. The
pass code and its restrictions are set in five menu stages.
7.9.1 Enter Pass Code
Enter the existing or a new four digit pass code using the
handset
numeric keypad
to gain access to the following Parental
Control menus. Ensure you keep a record of the pass code.
DVD5