NAIM AV2 Owner's Manual - page 18
16
AV2
15 AV2 Basics and Quick Setup
Installation of the AV2 requires two setup routines to be carried out - input setup
and speaker setup. These routines configure the AV2 for the source equipment and
loudspeakers it is to be used with and specify some signal decoding options. Some
parameters depend on the state in which the AV2 was last switched off so setup
may be simplified if the AV2 is returned to its setup defaults. See Section 21 for
notes on restoring setup defaults.
15.1 Switching On and Off
To wake AV2 from standby (power switch on).
Handset:
Press
standby
.
Front panel:
Press and hold
input
or
mode
.
To put AV2 to sleep (power switch on).
Handset:
Press
standby
.
Front panel:
Press both
input
and
mode
.
15.2 Input Setup Routine
To enter setup mode.
Handset:
Press
menu
followed by
i/p
5
.
Front panel:
Press and hold
input
.
To scroll up or down parameter list.
Handset:
Press
2
5
or
8
6
.
Front panel:
press
input
or
mode
.
To Adjust setting.
Handset:
press
3
4
or
6
4
.
Front panel:
rotate
rotary
control.
Setup Parameters
Parameter Settings
To exit setup mode.
Handset:
Press
menu
followed by
i/p
5
.
Front panel:
Press and hold
input
.
mode
2
5
8
6
8 c h . . . a n 1. . . s c d
input
menu
i/p
5
input
Or
3
4
6
4
Or
Or
Or
input
mode
input
mode
standby
Or
Or
Or
And
Versatile Analogue Input 1 (select source, multi)
V i 2
V i 1
- - - . . . a n 2 . . . s c d
Versatile Analogue Input 2 (select source, multi)
A N 3
- - - . . . a n 3 . . . s c d
Analogue Input 3 (select source)
A N 4
- - - . . . a n 4 . . . s c d
Analogue Input 4 (select source)
a n 5
- - - . . . a n 5 . . . s c d
Analogue Input 5 (select source)
a n 6
- - - . . . a n 6 . . . s c d
- - - . . . o p 1. . . s c d
- - - . . . o p 2 . . . s c d
Analogue Input 6 (select source)
o p 1
Optical Digital Input 1 (select source)
o p 2
- - - . . . co 1. . . s c d
- - - . . . co 2 . . . s c d
r c 5
d a t
Optical Digital Input 2 (select source)
co 1
Coaxial Digital Input 1 (select source)
co 2
Coaxial Digital Input 2 (select source)
e x t
Remote Control
Note:
Analogue inputs 1
and 2 can be combined to
provide one 8 channel or 6
channel input. In either case
input 2 is then unavailable.
For a complete description of
this facility see Sections 16
and 18.
Note:
With DAT (data)
selected for the EXT
parameter RC5 (remote
handset) control is disabled.
RC5 can be re-enabled using
the front panel controls.
Note:
The “Panorama”,
“Centre Width” and
“Dimension” stages of
the input setup routine
provide adjustment for
three Dolby* Surround Pro
Logic II music programme
decode parameters. It is
not necessary to set these
parameters initially. See
Section 17 for detailed
information on these decode
parameters.
Dolby Surround Pro Logic II “Panorama”
Dolby Surround Pro Logic II “Dimension”
Dolby Surround Pro Logic II “Centre Width”
D
w
P a n
o f f
o n
0 0 - 0 7
0 0 - 0 6
standby
Note:
The diagrams provide
a short-cut through the setup
routines. They can also be
used in conjunction with the
detailed notes in Section 18
where setup choices and
display legends are explained
in greater depth.
input
menu
i/p
5
Or
Lip Sync adjustment (milliseconds)
DTS Neo:6 “Centre Gain”
SY N
N E O
0 0 - 0 5
0 0 - 1 5 0