1 using your xp-400 security system napco © 2005 napco oi300 1/05 xp-400_rpxp4gt_oi300.02_... Page 1 friday, january 28, 2005 13:42 composite.
2 this page intentionally left blank xp-400_rpxp4gt_oi300.02_... Page 2 friday, january 28, 2005 13:42 composite.
3 introduction congratulations on your purchase of an advanced napco express xp-400 security system. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind, and incorporates some of the most sophisticated ...
4 introduction system information central station phone number: ____________________ central station account number: ____________________ for service call: ____________________ entry delay: ____________________ exit delay: ____________________ alarm time-out: ____________________ table of contents k...
5 keypad controls and indicators * key used to enable special functions and options. Press * and then the corresponding special function num- ber option (see special functions, page 10) bypass key used to bypass zones. Press bypass and the corre- sponding zone number, and then arm system. Numerical ...
6 arming your system when leaving 1 before arming your system, make sure the green x ready light is on. This indicates that all of your protective zones are secure. If any zones are open, the corresponding zone light will be on. Secure these zones before proceeding. If any zones cannot be secured, s...
7 protecting yourself while at home 1 before arming the system, the green x ready light must be on. This indicates that all of your protective zones are secure. If any zones are open, the matching zone light will be on. Secure those zones before pro- ceeding. 2 enter your user code. The green x read...
8 emergency buttons the two sets of emergency buttons, if programmed, are always active whether the system is armed or disarmed. Discuss these buttons with your installer. The emergency signal will only be activated when the two respective buttons are pressed at the same time. Auxiliary alarm: simul...
9 disarming your system when returning 1 enter your premises through the entry/exit door. The keypad will sound a steady tone to remind you to disarm the system before your entry delay time expires. 2 enter your user code. The red w armed light will go out, indicating that the system has been disarm...
10 special functions a by pressing a followed by the appropriate key, (do not press simultaneously) these special functions and features can be enabled: a 0 easy arm (when system is disarmed) the easy arm feature allows the system to be armed by pressing a followed by 0 . This will allow the easy ar...
11 your installer has assigned a user 1 code which may be used to not only arm and disarm the system, but also to enter the user program mode, where you can program and/or reprogram up to 4 user codes. The following explains how you will use this code to program or erase additional user codes. Enter...
12 the xp-400 is constantly monitoring its own components, as well as all critical services, such as ac power and the telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the yellow h ...
13 h system troubles keypad beeps or h system flashes zone light on system trouble condition action 2 beeps 1 bell / siren trouble there is a problem with the bell or siren. Call installing com- pany for service. 2 beeps 3 wireless receiver trouble a problem has been detected with the wireless recei...
14 glossary ambush code - in the event that you are forced by an intruder to disarm your sys- tem, this special code can be used to dis- arm the system, and simultaneously send a silent alarm to the central station. If your system has the ambush feature en- abled, the code assigned as the user 4 cod...
15 notes xp-400_rpxp4gt_oi300.02_... Page 15 friday, january 28, 2005 13:42 composite.
16 napco limited warranty the following statement is required by the fcc . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. I...
