DL manuals
Navnet
Boating Equipment
TZ 2 touch
Installation Checklist

Navnet TZ 2 touch Installation Checklist - Dff1 Mode Switch Settings

Page of 8

Download

Print this page

Bookmark us

DFF1 MODE Switch Settings

Connection to NavNet 1, vx2, 3D, TZtouch & TZtouch2

The DFF1 is defaulted to work with NavNet 3D MFDs. If you are connecting the DFF1

to an original NavNet 1, vx2, TZtouch only, or TZtouch2 network, you need to change

the MODE switches as shown below.

If the DFF1 will be installed in a network comprised of a NavNet 3D MFD8, MFD12 or

MFDBB AND a TZtouch display in a mixed configuration, the DIP Switches must

remain in the default settings shown below.

Please confirm the dip switch selection for your type of NavNet display. To access the

dip switches, remove the rubber cap on the front of the DFF1 unit.

Default settings

for NavNet 3D

Alternate settings for NavNet 1,

vx2, TZtouch & TZtouch2

This setting is used when connecting the DFF1 directly to a NavNet 3D

MFD or to a NavNet 3D network using the HUB101.

This setting is used when connecting the DFF1 to NavNet 1, vx2, TZtouch

or TZtouch2. This setting must also be used when connecting to a NavNet

3D network using an Ethernet Hub or Switch, other than the HUB101.

Alternate settings:

Default settings:

If you have more than one network sounder in the system, please contact Furuno Tech

Support for setup information.

APPENDIX 2

« ‹ Prev 2 3 4 5 6 7 8 Next › »

Summary of TZ 2 touch

Page 1
Installation checklist.
Page 2
2 navnet tztouch2 installation checklist navnet tztouch2 network installation  connect all tztouch2 mfds to the ethernet network. If a hub101 is used, set the internal hub dip switches to off (hub101 dip switches are off by default). Tztouch2 mfds do not use power synchronization. Using a generic e...
Page 3
3  power on the ethernet hub/switch, psu, the nmea2000 backbone and all the sensors, and then power on the tztouch2 mfds.  furuno recommends at least one tztouch2 mfd be installed in a location that ensures the mfd can receive a gps signal, thus providing gps data to the network. If this is not po...
Page 4
4  if the transducer is listed as being eligible for “enhanced” rezboost mode, please enable enhanced mode in the fish finder pop-up menu.  select the preferred data/sensor sources for the network by pressing the “data source” button in the “initial setup” menu.  select the nmea2000 pgns that you...
Page 5: Appendix 1
If you have more than one network sounder in the system, please contact furuno tech support for setup information. The dff1-uhd is defaulted to work with navnet tztouch and tztouch2 mfds. If you are connecting the dff1-uhd to any tztouch, tztouch2, or combined system, you do not need to change the d...
Page 6: Dff1 Mode Switch Settings
Dff1 mode switch settings connection to navnet 1, vx2, 3d, tztouch & tztouch2 the dff1 is defaulted to work with navnet 3d mfds. If you are connecting the dff1 to an original navnet 1, vx2, tztouch only, or tztouch2 network, you need to change the mode switches as shown below. If the dff1 will be in...
Page 7: Dff3 Mode Switch Settings
If you have more than one network sounder in the system, please contact furuno tech support for setup information. Only change settings for s2. Do not change settings for s3. The dff3 is defaulted to work with navnet 3d mfds. If you are connecting the dff3 to an original navnet 1, vx2, tztouch or tz...
Page 8: Appendix 4
When the psu012 or psu013 power supply unit is connected to a tztouch or tztouch2 mfd, attach the shorting jumper (supplied) to j7 on the pwr board. (psu012 = 03p9481) (psu013: 03p9483) 8 psu012/psu013 jumper location for tztouch & tztouch2 installations appendix 4.