Océ CS9360 Installation Manual - page 4
CS9360 INSTALLATION MANUAL
AP-40810_1.0 4
No.
Name
1
Waste fluid valve
3. Peel off the tape, be careful not to come in contact
with T fence, and remove the Bearer collapse pre-
vention material and Bearer fix.
4 Installation
Procedures and environment for installing this product
are explained.
4.1 Installation environment
Install this product to the appropriate place with refer-
ence to the following.
4.1.1 Installation environmental condition
Select an installation location in accordance with the
table below.
4.1.2 Installation space
Install on a level floor which meets the following condition.
It has enough strength to support the weight of the
printer and the stand.
4.2 Installation procedure
Install this product to the installation place in accord-
ance with the list shown below.
1. Check that the eight butterfly bolts attaching the
stand and the printer are not loose.
2. Carry the printer to the installation place.
3. Turn the following adjusters in the direction as
shown below to prevent the printer from moving.
・
Adjusters : 4 locations
4. Confirm that the waste fluid valve is closed.
5. Check that the eight butterfly bolts (8 pieces) at-
taching the stand and the printer are not loose.
5 Connecting the power cable
This section explains how to connect the power cable.
Follow the steps below to connect the power cable.
1. Confirm that the product is turned OFF.
More than 2940 Pa (300 kg/m
2
)
Power
Specifica-
tion
Environm-
ental
conditions
Floor strength of
installation place
Power
Supply
Frequency
Range
AC 90 V to 132 V / 198 V to 264 V
50/60Hz ± 1Hz
Power
capacity
Change
rate
Operative
condition
Guaranteed
range of
printing
accuracy
Main: 12A
Heater: 12A
Temperature: 20 °C to 32 °C
Humidity: 40 % to 60 %, No Condensation
Temperature: 22 °C to 30°C
Humidity: 40 % to 60 %
Temperature: within 2 °C per hour
Humidity: within 5 % per hour
NOTE
For temperature and humidity, avoid locations
such as the following. There is a possibility that
the print quality will be affected.
Places where temperature or humidity may
rapidly change, even though within the required
conditions.
Places that receive direct sunlight, increased illu-
mination or direct air, for example from an air
conditioner.
To keep the temperature and humidity constant, in-
stall this product in a location where the air condi-
tion is adjustable.
NOTE
Please check that the butterfly bolts are not loose
before/after carrying this product.
When transferring or carrying outside, separate the
printer and the stand.
Do not install the printer in the follow-
ing places where there is a possibility
that the printer may be damaged or
might fall or be fallen by chance.
On a shaky stand
Slanting location
Places where vibration of other machines
etc. is transmitted.
Do not stamp on the printer or do not
place heavy things on top of it. The
printer may be damaged or might fall
or be fallen by chance.
Cover the printer with blanket and cloth
like tablecloth and do not close the vent.
If the vent is closed, the printer could
accumulate heat inside and may cause
fire.
Do not install the printer in a location
that has high humidity or is dusty.
It could lead to electric shock and fire.
WARNING
Make sure not to damage T fence dur-
ing operation.
If T fence is damaged, it will affect
print results.
WARNING
1
2
3
4
1
For the weight of the printer and the stand, refer to
the Operation Manual.
NOTE
WARNING
Be sure to use the specified power cable
(separately sold).
Using power cables other than the specified
can cause an electric shock or fire.
Use a power cord set which is compatible
with the safety standards, power supply
voltage, and plug shape used in the country
where this printer is used.
Use a power cord set which is equipped
with a protective earth, and securely con-
nect it to the outlet.
Do not use a damaged power cable.
It may cause an electric shock or fire.
1
a= 650 mm
b=1,000 mm
c=1,000 mm
d=1,000 mm
e=1,550 mm
f =3,800 mm
g=2,700 mm
g
e
a
d
b
c
f
1
1
1
2
No.
Name
1
Adjuster
No.
Name
2
Stand
No.
Name
1
Tape
3 Bearer protective material
No.
Name
2
T fence
4
Bearer fix