Oki C7350hdn Safety And Regulatory Information Manual - page 4
4 - English
Always hold the power plug to connect/disconnect the power cable
to/from the mains socket. Unplugging by pulling on the cable can
cause fraying and may lead to fire or electric shock.
This product has an earthed plug as a safety feature and will only
connect to an earthed socket. Do not attempt to defeat the earthing
or there is a risk of fire or shock.
If using an extension cable or power strip ensure that the total
current rating (amperes) of all connected equipment is less than the
maximum rating of the extension cable, power strip or wall outlet. If
the product is already supplied with a fitted power strip then no
additional power strip or extension cable should be used to connect
to the mains wall outlet. Otherwise, fire or shock may occur.
Ensure the power cable is routed so as not to be damaged or cause a
trip hazard. If the cable becomes frayed or damaged replace it
immediately to prevent any risk of shock.
Do not twist, constrict or knot the power cable as this can cause
overheating which may lead to fire or electric shock.
Ensure the power socket to which the product is connected is easily
accessible at all times and not obstructed.
Use only the power cable supplied. Using a power cable not intended
for this product may lead to fire or electric shock.
To avoid risk of fire and electric shock, do not use the power cable
supplied with this product for any other electrical equipment.
If you do not connect the power cord or any other cables only as
directed in the User's Guide, this may result in a fire.
It is recommended that the machine is switched off prior to opening
covers; otherwise there is a risk of electric shock.
When the product cover is open, do not touch the fuser unit or print
head as you may receive burns. Allow it to cool before touching.
If the product casing gets extremely hot or smoke, unusual smells or
abnormal noises are emitted from the product, there is a risk of fire.
Unplug the mains connector and contact your dealer.
If the product has been knocked over or damaged, there is a risk of
electric shock, fire and/or injury. Unplug the mains connector and
contact your dealer.
If any liquid (for example water) is allowed to enter the product,
there is a risk of fire. Unplug the mains connector and contact your
dealer.
Do not place containers containing liquid on the product as electric
shock, fire and/or injuries may occur.
If any foreign objects (for example clips) are allowed to enter the
product, there is a risk of electric shock, fire and/or injury. Unplug
the mains connector before removing the object.
Do not introduce foreign objects into the ventilation holes or operate
this product with any covers open or doors removed as electric shock,
fire and/or injuries may occur.
Do not use an extremely flammable spray near the product as the
product contains high temperature parts that may cause a fire.
Switch the product off before cleaning to prevent any risk of injury.
Clean using a damp cloth. Do not use liquid or aerosol cleaners.
Ensure loose clothing and hair is kept clear of moving parts when the
product is in operation to prevent possible risk of injury.
Do not carry out any operations on the product that are not specified
in the User's Guide. This may result in electric shock, fire and/or
injury.
Do not touch the battery if one is fitted to the product. There is a risk
of explosion if the battery is replaced by an incorrect type. The
product battery should not require replacement during the life of the
product.
Do not throw toner cartridges or image drum cartridges into a fire as
you may receive burns from a dust explosion.
After installing additional memory, hard disk drive, or any other
internally fitted option, any covers removed or doors opened must
be closed or replaced and secured to prevent risk of fire.
The acoustic noise of this product is less than 70 dB (A) as measured
in accordance with EN ISO 7779.
The operating condition range for your product is: 10 to 32°C and 20
to 80% RH. Operation of the product outside this range could result
in damage to the product.
If a scanner, finisher etc. is fitted, exercise care when moving these
items so as to avoid risk of entrapment or personal injury.
If the product is installed on a cabinet or high capacity feeder, ensure
wheel locks are applied once placed in final position for use, to
prevent risk of movement or injury.
English
Limited Warranty, U.S. and Canada only
U.S. and Canada only
Oki Data Americas, Inc. (Oki Data) warrants this C7350/7550
(hereinafter "the Product") to be free from defects in material and
workmanship and will remedy any such defect according to, the
terms of this Limited Warranty.
Oki Data will repair or at its option, replace, with the same or its
functional equivalent, at no charge, any defective component(s)
of the Product for one (1) year from the date of purchase except
for the printhead (LED imaging array), which is warranted for a
period of five (5) years from the date of purchase.
This Limited Warranty only extends to the original purchaser of
the warranted item. This Limited Warranty is not transferable.
This Limited Warranty does not extend to consumable items or
supplies, such as toner cartridges, image drums, ribbon
cartridges, fuses, etc.
Overnight Exchange
US and Canada Only
Oki Data offers Overnight Exchange of the Product under
this Limited Warranty. Overnight Exchange is only available
in the United States and Canada and it does not include the
replacement or repair of the Product's consumable items or
supplies.
If you choose to use our Overnight Exchange service, call
1-800-654-3282 (1-800-OKI-DATA): our trained personnel
will try to solve your problem over the phone. If they
determine that your Product hardware is defective, an
exchange product will be shipped to you via overnight
carrier. Have your credit card available as our
representative will be asking for this information. You will
receive the exchange product the next business day—or no
later than the second business day.
Return the original Product to Oki Data by using the same
packaging materials you received with the exchange
Product. The Product to be returned must be made
available for pickup by Oki Data's representative within two
(2) business days of your receipt of the exchange product:
failure to do so may result in your being charged the full
price of the exchange unit.
Before you ship the product, remove the image drums and
toner cartridges to prevent damage to the product during
shipment: failure to do so may result in your credit card
being charged for cleaning and/or repairs to the Product.
When Overnight Exchange is used, the returned machine
becomes the property of Oki Data, once it has been picked
up by Oki Data or its representative. Exchange machines
may be new or reconditioned, at the option of Oki Data: the
exchange machine becomes the property of the customer
when the returned machine has been picked up by Oki
Data's designated carrier.