1. DL manuals
  2. Oki
  3. Printer Accessories
  4. OKIPAGE 12i Series
  5. Troubleshooting Manual

Oki OKIPAGE 12i Series Troubleshooting Manual

Manual is about: Digital LED Printer

Summary of OKIPAGE 12i Series

  • Page 1

    All specifications are subject to change without notice. Okipage 12i led page printer troubleshooting manual with component parts list oda/oel/int.

  • Page 2

    Okidata is a registered trademark of oki america, inc. Okidata est une marque déposée de oki america, inc..

  • Page 3: Contents

    Contents 1. Outline......................................................................................................... 1 2. Tools ............................................................................................................ 1 3. Circuit description .................................

  • Page 4

    - 1 - 1. Outline this manual has been written to provide guidance for troubleshooting of the okipage 12i printer (primarily for its printed circuit boards), based on the assumption that the reader has a thorough knowledge concerning the printer. Read the maintenance manual for this printer, if neces...

  • Page 5

    - 2 - 3. Circuit description 3.1 outline the main control board controls the reception of data transferred through a host i/f and processes command analysis, bit image development, raster buffer read. It also controls the engine and the operator panel. Its block diagram is shown in fig. 3-1 and 3-2....

  • Page 6

    - 3 - figure 3-1 block diagram 1mb memory board (option) rs232c interface board (option) network interface board (option) or program & font rom 16mb mask rom resident ram 1m x 16 dram (4mb) for optional board main control board power supply board or data bus (32bit) eeprom 7407 inlet sensor 1 inlet ...

  • Page 7

    - 4 - figure 3-2 memory expansion board block diagram (option) option connector a2 to a23 cs3, eepcs, eeclk eepdat ios1 cas0 to cas3 ras2 to ras4 ore, rd, wr d0 to d31 pd2, 3 bsy rd wr ras3, 4 wr ras2 ore wr dram 1m byte als244 als244 als244 als244 simm1 dram simm simm2 flash simm.

  • Page 8

    - 5 - figure 3-3 rs-232c serial interface board block diagram (option) a2 to a23 cs3, eepcs, eepclk eepdat ios1 txd, rst, dtr rxd rs-232c connector cas0 to cas3 ras2 to ras4 ore, rd, wr d0 to d31 pd2, 3 bsy rd wr ras3, 4 wr als244 als244 75188 als244 als244 simm1 dram simm simm2 flash simm option co...

  • Page 9

    - 6 - figure 3-4 network interface board block diagram (option) a2 to a23 cs3, eepcs, eepclk eepdat ios1 ios0 cs2 int2, dmarq 10 base t connector cas0 to cas3 ras2 to ras4 ore, rd, wr d0 to d31 pd2, 3 bsy1 bsy2 cs2 rd wr rd wr ras3, 4 wr als244 als244 als244 als244 simm1 dram simm simm2 flash simm f...

  • Page 10

    - 7 - 3.2 cpu and memory (1) cpu (mhm2029-004k) cpu core risc cpu (mips r3000 compatible) cpu clock 20.2752 mhz internal cpu clk 40.5504 mhz (2) program and font roms rom capacity 16m bytes (64m bit mask rom two pieces) rom type 64m bits (4m x 16 bits) access time 100 ns (3) resident ram ram capacit...

  • Page 11

    - 8 - figure 3-8 block diagram of cpu & memory circuit cpu cs0 cs2 cs3 cs4 cs0 rd ras0 rd/wr cas0, 1, 2, 3 ras2, 3, 4, 5 cas0, 1, 2, 3 rd/wr main control board ras0 ras1 ras2 ras3 ras4 ras5 cas0 cas1 cas2 cas3 option board ic4, ic5 dram (1m x 16 bits) 2 pieces dram 1m byte ras2 wr d00 to d32 a00 to ...

  • Page 12

    - 9 - figure 3-9 timing chart of cpu & memory circuit (40.5504 mhz) sysclk a00-a25-p dras0~5-n dcas0~3-n rd-n d00~d31-p 0 12.33 24.66 36.99 49.32 61.65 73.98 86.31 98.64 110.97 123.30 (ns) t2 -7 sysclk t1 -2.5 sysclk t3 -1 sysclk t2 -7 sysclk 46.0 32.0 (dras0n~ 5n) t4 -3.5 sysclk t2 -7 sysclk t2 -7 ...

  • Page 13

    - 10 - power off power on +38v +38v +8v ic10 input clrst-n +5v +8v ic10-6 ic10-5 +38v +8v +5v ic10 to option board cpu 5 6 d2 (15v) 172 + – 7 3.3 reset control when power is turned on, a clrst-n signal is generated by the rising sequence of +38v and +8v power supply..

  • Page 14

    - 11 - instruction start bit operation address data code read (read) 1 10 a7 to a0 write enabled (wen) 1 00 11xxxxxx write (write) 1 1 01 a7 to a0 d15 to d0 write all address (wral) 1 00 01xxxxxx d15 to d0 write disabled (wds) 1 00 00xxxxxx erase 1 11 a7 to a0 chip erasable (eral) 1 00 10xxxxxx writ...

  • Page 15

    - 12 - cpu cent 87, 88, 91 to 96 pdata1-p to pdata8-p pstb-n pbusy-p pack-n ppe-p perror-n psel-p pinit-n pselin-n pautofd-n 97 85 86 83 81 79 80 82 84 2 to 9 1 11 10 12 13 32 31 36 0 data8-p to data1-p stb-n busy-p ack-n pe-p fault-n iprime-n sel-p selin-n autofeed-n +5v 14 5v +5v 18 ic11 3.9k Ω pa...

  • Page 16

    - 13 - sstxd-p main control board olcc-2 3 4 6 1 4 3 1 6 44780 lcd control driver zebra rubber lcd flexible cable cpu led 154 db4~db7 rs r/w e 158 153 152 cn1 panel ssrxd-p ssclk-n ssld-n lsi bu6152s command (first) bit 0 bit 7 command (second) bit 7 bit 0 command response (first) command response (...

  • Page 17

    - 14 - strb1-n strb2-n strb3-n strb4-n loadi clocki datai0 datai1 datai2 datai3 msm6730 waf eeprom correction values led led led led led led led led driver msm6732bwaf led driver msm6732bwaf led driver msm6731bwaf led driver msm6731bwaf led array printing and correction data combined signal line cor...

  • Page 18

    - 15 - clocki loadi datai3~0 strb1i-n strb2i-n strb3i-n strb4i-n normal mode printing timing chart first line printing data sent second line printing data sent first line printing the printing operation is carried out in the following sequence. First, the printing data datai3 through datai0 are stor...

  • Page 19

    - 16 - cpu a2918sw mtd2005f m main (drum) motor m dmph1-p 132 13 rmph2-n 3 12 rmph2-p 4 8 rmph1-n 2 7 rmph1-p 1 3 dmph2-p 4 4 dmph2-n 3 2 dmph1-p 2 17 dmph1-n 1 1 +38v +38v ic9 ic8 registration motor main control board rm dm dmph2-p 131 8 dmon1-n 127 7 14 rmph1-p 134 26 rmph2-p 133 17 rmon-n 3 27 16...

  • Page 20

    - 17 - operation at normal speed: t0 to t3 = 0.82 ms rmon-n rmph1-p rmph2-p t0 t1 t2 t3 rotation forward rotation hopping drive reverse rotation registration roller drive stop (3) registration motor (4) drive control time t0 to t3 determines the motor speed, while the difference of phase direction b...

  • Page 21

    - 18 - ic2 cpu main control board power supply board thermistor 27 th1 th2 5v 1 2 pc1 acin heaton-n 116 thermistor breakdown detector circuit power supply interface heater cn2 abnormally high temperature detection circuit 5v ic11 1 2 20 0c 3.9 fuser temperature control for the temperature control by...

  • Page 22

    - 19 - on off on off on heaton-n v1 v2 temperature ˚c vt v2 176˚c v1 175˚c (standard temperature) * the values v1 and v2 vary according to setting mode. The temperature control is described below. When vt rises to v2 or more, the heater is turned of (by setting heaton-n signal to low). When vt drops...

  • Page 23

    - 20 - ic2 a/d converter thermistor breakdown detection circuit 5v + – r26 1k Ω therm-cmp thermistor +5v +5v r27 1.8k Ω 324 r28 1k Ω q7 q6 ic4 heat-n0 to pc1 from cpu r24 1.5k Ω r25 100k Ω abnormal high temperature detection circuit for heater breakdown detection, the heater must first be turned on....

  • Page 24

    - 21 - main (drum) motor heater control fan motor off off on on heater hold time rotation state 8 min. Or 0 sec. 30 sec. Stop state fanon1-p fanalm-p fan move 0.7 sec max lock fanon1-p h h l fanon2-n l h x fan motor rotation normal speed half speed stop 1 2 3 fan fan motor cpu fanon1-p 109 fanon2-n ...

  • Page 25

    - 22 - cpu main control board +5v power supply board cvopn-n cover open microswitch +5v +5v 0v cover close cover open low voltage power supply unit high voltage power supply unit high voltage output 125 +5v cvopn-n 3.11 cover open when the cover is opened, a cover open microswitch is opened. This ma...

  • Page 26

    - 23 - sclk sqcr data in data out ch db sb tr cb cpu high voltage power supply unit +5v cover open switch trsel 3 trsel 4 trsel 5 power supply board f3 f2 f1 l fg n thermal fuse 1 2 1, 2 3, 4 6 5 ac transformer +38v smoothing circuit +5v stabilizing circuit +38 v 17, 18 +5 v 11, 12 0 v 9, 15, 16 +8 ...

  • Page 27

    - 24 - off main control board power supply board psout-n wrsns-n paper-n psin1-n tnrsns-n psin2-n ic2 +5v ps1 ps2 ps4 ps3 ps6 ps5 on transparent shield sensor signal 7 6 8 4 3 5 +5v (3) sensor control.

  • Page 28

    - 25 - cb +400v -1.35kv cpu power supply circuit main control board ic2 lsi db sb cb ch tr 13 15 11 14 12 +5v sb db cb tr ch 11 12 13 14 15 sb 0v db +300v -500v -265v tr +1.2kv -1.1kv ch -1.3kv remarks power supply interface high-voltage outputs high -frequency pulse output pins part with slant line...

  • Page 29

    - 26 - 3.13 option tray control the kinds of option trays, high capacity second paper feeder and multi purpose feeder can be connected to the printer. The trays are distinguished by two digit id numbers. The option trays and the printer communicate with each other through bi-directional clock syncho...

  • Page 30

    - 27 - option tray connection and block diagram 5v 5v 0v 30v 5v 0v pu 2nd tray tr2 270 Ω 3 d1 d2 ic3 ic1 6 0c 5 4 3 0c 2 1 tqsb-2 (option) ic2 65-43 f0 f2 g2 e0 c2 g0 f1 c1 c0 d0 e1 a b c d sw1 1, 2 3, 4 11 29 24 20 21 4 7 22 560 Ω 2 1 0c 10 9 28 9 5 3 8 6 ms4646 a b 10 19 25 4 mb1 mb2 ma1 ma2 vr1 v...

  • Page 31

    - 28 - optsd-p min. 3000 µ s option tray control serial interface time chart b7 b6 b5 b4 b3 b2 b1 b0 b7 b6 b5 b4 b3 b2 b1 b0 b7 b6 b5 b4 b3 b2 b1 b0 1.5 µ s 40 µ s 21 µ s min. 1300 µ s max. 3000 µ s optsclk-n optsdr-n next command (cpu → tray) reply (tray → cpu) command (cpu → tray) option tray seri...

  • Page 32

    - 29 - motor on (c2) phase change (c1, c0) paper sensor (optpsin-n) triggered by cpu automatically stops # of phase changes after paper sensor detection is downloaded by cpu motor control time chart option tray motor control time chart.

  • Page 33

    - 30 - 3.14 memory expansion option board the memory expansion option board is provided with two dram chips and two simm slots. The simm1 slot is used for installation of a dram simm. The simm2 slot is used for installation of a flash simm. With the board, a printer will have 5m bytes of memory even...

  • Page 34

    - 31 - 3.15 rs-232c serial interface option board rs-232c serial interface board block diagram (option) the rs-232c serial interface option board is provided with a rs-232c i/f and two simm slots. The simm1 slot is used for installation of a dram simm. The simm2 slot is used for installation of a fl...

  • Page 35

    - 32 - (1) rs-232c interface the serial data rxd from the host system, whose line voltage is clamped at the ttl level by d4/d512, are received by the cpu built-in serial controller. Dsr and cts signals are terminated through 5.6k Ω resistors. Send signals txd, rts and dtr are put out from the cpu an...

  • Page 36

    - 33 - (2) simm memory module the board is provided with two slots for a 72-pin dram simm memory module and flash simm. The simm1 slot is used for installation of a 72-pin dram simm memory module. Up to 6 types of simm memory module can be installed. 1m byte, 2m bytes, 4m bytes, 8m bytes, 16m bytes ...

  • Page 37

    - 34 - 3.16 network interface option board network interface board block diagram (option) the network interface option board is provided with a network i/f, one flash rom chip and two simm slots. The simm1 slot is used for installation of a dram simm. The simm2 slot is used for installation of a fla...

  • Page 38

    - 35 - 3.17 flash-simm option (for font datas) the flash-simm option (flash-simm option is provided with four font roms and one eeprom.) the flash-simm is installed to simm slot on the memory extension option board, rs-232c serial interface option borad or network interface option board. (1) font ro...

  • Page 39

    - 36 - 4. Troubleshooting 4.1 troubleshooting table (a) power supply board (ol1- or ol2-pcb) note: the malfunction of the power supply is not repaired by an agency. The abnormality to be treated here is that of sensors only. Failure lcd message flowchart no. Paper input jam occurs frequently. #: tra...

  • Page 40

    - 37 - failure lcd message flowchart no. Abnormal message display on the lcd (no display, unclear display, display with some dot not lit). B - 1 program rom error. Or b - 2 font rom error. B - 3 resident ram error. B - 4 eeprom error. B - 5 option ram error. B - 6 cooling fan error. B - 7 ssio error...

  • Page 41

    - 38 - failure lcd message flowchart no. Processor error. E r r o r 0 * b - 13 b - 14 b - 15 print overrun occurs frequently. B - 16 error host i/f occurs frequently. B - 17 error receive buffer overflow occurs frequently. B - 18 paper input jan occurs frequently. #: tray1, tray2, feeder, manual b -...

  • Page 42

    - 39 - failure lcd message flowchart no. Abnormal message display on the lcd (no display, unclear display, display with some dot not lit, etc.) c - 1 the key switch operation on the operator panel is disabled. C - 2 the lcd does not display any message. C - 3 display on the lcd with some dot not lit...

  • Page 43

    - 40 - failure lcd message flowchart no. Paper input jams occur frequently. D - 1 paper out occurs even if the papersare in cassette or a tray. D - 2 second tray cover open errors occur even if the cover is closed. D - 3 the printer does not recognize an option tray. D - 4 t r a y 2 i n p u t j a m ...

  • Page 44

    - 41 - failure lcd message flowchart no. Option ram error. F - 1 e r r o r 6 0 option simm error. I - 1 r o m - s i m m e r r o r (f) memory expansion option board (mm6).

  • Page 45

    - 42 - (g) network interface option board (mn6) failure lcd message flowchart no. Option simm error. I - 1 error host i/f occurs frequently. G - 1 r o m - s i m m e r r o r h o s t i / f e r r o r.

  • Page 46

    - 43 - (h) rs-232c interface option board (smif) failure lcd message flowchart no. H - 1 error host i/f occurs frequently. Loop test error occurs during loop test. H - 2 h o s t i / f e r r o r i - 1 option simm error. R o m - s i m m e r r o r (i) flash-simm (font simm option) failure lcd message f...

  • Page 47

    - 44 - 4.2 troubleshooting flowchart a-1 paper input jam occurs frequently. • is ps3 (inlet sensor 1) operating normally? • no replace ps3. ▼ • yes is ps5 (inlet sensor 2) operating normally? • no replace ps5. ▼ • yes replace ic2 (lc26023a). A-2 paper feed jam occurs frequently. • is ps3 (inlet sens...

  • Page 48

    - 45 - a-4 paper size error occurs frequently. • is ps3 (inlet sensor 1) operating normally? • no replace ps3. ▼ • yes is ps5 (inlet sensor 2) operating normally? • no replace ps5. ▼ • yes replace ic2 (lc26023a). A-5 the message “tray paperout” remains displayed on the lcd • is ps4 (paper end sensor...

  • Page 49

    - 46 - a-9 the printer does not function at all, and the lcd does not display any messages. • is fuse f1 open? • yes replace f1. ▼ • no is the voltage waveform between pins 1 and 3 of the connector (cn2) same as the waveform shown below? • no replace the transformer t1. ▼ • has the problem been solv...

  • Page 50

    - 47 - • no replace the transistor q1. ▼ • has the problem been solved? • yes end. ▼ • no replace the transistor q2. ▼ • has the problem been solved? ▼ • no replace ic1 (fa7617p-1). ▼ • yes check the connection between the power supply board and main control board. A-10 thermistor open error (error ...

  • Page 51

    - 48 - a-11 serial interface does not connect to the host device. • is the voltage waveform between pins 5 and 6 of the connector (cn2) same as the waveform shown below? • no replace the transformer t1. ▼ • has the problem been solved? • yes end. ▼ • no replace the diode d10. ▼ • yes is the voltage ...

  • Page 52

    - 49 - b-1 abnormal message display on the lcd. • replace ic2, ic3. ▼ • has the problem been solbed? • yes end. ▼ • no is the 20.2752-mhz clock signal being sent to pin 3 of osc1? • no replace osc1 (cst 20.27mxw). ▼ • yes is the output at pin 7 (reset-n) of ic10 ( µ pc393g2) normal (see section 3.3 ...

  • Page 53

    - 50 - b-6 option ram error (error 60). • remove the dram simm. Has the problem solved. • yes failure of dram simm. ▼ • are negative pulses being sent to pin 83 (dras2-n), pin 84 (dras3-n), pin 85 (dras4-n), pin 86 (dras5-n) of the connector (option)? • no failure of ic1 (mhm2029-005k). ▼ • yes fail...

  • Page 54

    - 51 - b-10 option tray i/f timeout error (error 81). • is the connection at the connector (2ndtray) properly engaged? • no replace the connector (2ndtray). ▼ • yes is the connection at the connector (envelope) properly engaged? • no replace the connector (envelope). B-11 watchdod timer timeout erro...

  • Page 55

    - 52 - b-14 print overrun occurs frequently. • is an option board mounted? • yes go to the flowchart b-6. ▼ • no set dram simm memory module on an option board, then mount it to the printer. • has the problem been solved? • yes print data is too complex to print out, so it is necessary to mount an o...

  • Page 56

    - 53 - b-17 paper input jam. • is the hopping motor rotating normally? • no are the waveforms of rmph1-p and rmph2-p signals as shown in section 3.9 (2) being sent to pins 26 and 17 of ic8 (mtd2005f) respectively? • no failure of ic1 (mhm2029-005k). ▼ • yes when the motor is rotating, does the outpu...

  • Page 57

    - 54 - b-18 paper feed jam occurs frequently. • is the main (drum) motor rotaing normally? • no are the waveforms of dmph1-p and dmph2-p as shown in section 3.9 (1) being sent to pins 13 and 8 of ic9 (a2918sw) respectively? • no failure of ic1 (mhm2029-005k). ▼ • yes when the main (drum) motor is ro...

  • Page 58

    - 55 - b-21 data sent through the centronics i/f cannot be received. • is the signal at pin 11 (busy-p) of the connector (cent) low? • no is the signal at pin 3 (pbusy-p) of ic11 (74ls07) change at data reception as shown below? On-line off-line pbusy-p low high • no failure of ic1 (mhm2029-005k). ▼...

  • Page 59

    - 56 - c-1 abnormal message display on the lcd (no display, unclear display, display with some dot not lit, etc.) • is +5v power being supplied to pin 8 of ic1 (bu6152s)? • no replace cn1. ▼ • yes is the clock signal being sent to pin 26 (op-clock-n) of ic1 (bu6152s)? • no replace cn1. ▼ • yes is th...

  • Page 60

    - 57 - c-2 the key switch operation on the operator panel is disabled. • do the signals at pins, 3, 7, 10, 18, 23, 31 of ic1 (bu6152s) change from high to low level by key switch pushing? • no replace sw1 to sw8. ▼ • yes is the connection of cn1 correct? (olcc-pcb) • no connect the connector correct...

  • Page 61

    - 58 - c-4 display on the lcd with some dot not lit. • are 4.15v, 3.3v, 2.46v, 1.61v, and 0.77v powers being supplied respectively to pins 26, 27, 28, 29 and 30 of ic2 (hd44780)? • no replace r5 through r10. (olcc-pcb) ▼ • yes is the com signal being sent to pins 47 through 62 (com01 to com16) of ic...

  • Page 62

    - 59 - d-1 paper input jams occur frequently. • has the fuse f1 opened? • no is the high voltage (around 30v being sent to pin 2 of d1 and pin 2 of d2? • no replace d1 or d2. ▼ • yes is the signal level at pin 22 of ic2 at low level? • no replace ic2. ▼ • yes are the signals at pins 20 and 21 of ic2...

  • Page 63

    - 60 - d-4 the printer does not recognize high capacity second paper feeder. • do signal levels at pin 2 (optsclk-n) and 3 (optsd-p) pu alter at power-up time? • no replace cable. • no replace d1 or d2. ▼ • yes do signal levels at pin 4, 7, and 9 of ic2 alter at power-up time? • no is signal level a...

  • Page 64

    - 61 - e-1 paper input jams occur frequently. • is the motor rotating? • no has the fuse f1 opened? • no is the high voltage (around 30v) being sent to pin 2 of d1 and pin 2 of d2? • no replace d1 or d2. ▼ • yes is the signal level at pin 22 of ic2 at low level? • no replace ic2. ▼ • yes are the sig...

  • Page 65

    - 62 - e-3 the printer does not recognize multi purpose feeder. • do signal levels at pin 2 (optsclk-n) and 3 (optsd-p) cn1 alter at power-up time? • no replace option tray cable. ▼ • yes do signal levels at pin 4, 7, and 9 of ic2 alter at power-up time? • no is signal level at pin 2 of d4 at 3.9v? ...

  • Page 66

    - 63 - f-1 option ram error (error 60) • remove the dram simm. Has the problem been solved? • yes failure of dram simm. ▼ • are negative pulses being sent to pin 83 (dras2-n), pin 84 (dras3-n), pin 85 (dras4-n), pin 86 (dras5-n) of the connector (cn1)? • no failure of ic1 (mhm2029-005k) or main cont...

  • Page 67

    - 64 - g-1 error host i/f occurs frequently. • is the connection at the connector (cn2) properly engaged? • no replace the connector (cn2). ▼ • yes replace the t1 (td43-2006k) ▼ • is the 20.000 mhz clock signal being sent to pin 3 of osc1? • no replace osc1 (cx0-049 20.000 mhz) ▼ • replace the ic1 (...

  • Page 68

    - 65 - h-1 error host i/f occurs frequently. • is the connection at the connector (cn2) properly engaged? • no replace the connector (cn2). ▼ • yes is the voltage at pin 14 of q11 (75188) about +8v and the voltage at pin 1 of q11 (75188) about -8v? • no check the connection of the connector (cn1). ▼...

  • Page 69

    - 66 - i-1 option simm error (rom-simm error) • is the connection of simm2 slot correct? • no replace the simm2 slot. ▼ • yes remove the flash-simm. Has the problem been sloved? • yes failure of flash-simm. ▼ • no failure of ic1 (mhm2029-005k) or main control pcb (m5e)..

  • Page 70: 5.  Circuit Diagram

    - 67 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y 5. Circuit diagram.

  • Page 71

    - 68 - 5. Circuit diagram figure 5-1(1/11~11/11) main control board (m5e-pcb, rev.3) (40750002) figure 5-2(1/1) operator panel board (olcc-2-pcb, rev.4) (4ya4130-1001g2) figure 5-3(1/4~4/4) power supply board (ol1-pcb, rev.6) (40217701) figure 5-4(1/4~4/4) power supply board (ol2-pcb, rev.6) (402177...

  • Page 72

    1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y - 69 - figure 5-1 main control board (m5e-pcb, rev.3) (1/11).

  • Page 73

    - 70 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-1 main control board (m5e-pcb, rev.3) (2/11).

  • Page 74

    - 71 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-1 main control board (m5e-pcb, rev.3) (3/11).

  • Page 75

    - 72 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-1 main control board (m5e-pcb, rev.3) (4/11).

  • Page 76

    - 73 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-1 main control board (m5e-pcb, rev.3) (5/11).

  • Page 77

    - 74 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-1 main control board (m5e-pcb, rev.3) (6/11).

  • Page 78

    - 75 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-1 main control board (m5e-pcb, rev.3) (7/11).

  • Page 79

    - 76 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-1 main control board (m5e-pcb, rev.3) (8/11).

  • Page 80

    - 77 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-1 main control board (m5e-pcb, rev.3) (9/11).

  • Page 81

    - 78 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-1 main control board (m5e-pcb, rev.3) (10/11).

  • Page 82

    - 79 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-1 main control board (m5e-pcb, rev.3) (11/11).

  • Page 83

    - 80 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-2 operator panel board (olcc-2-pcb, rev.4) (1/1) cn1 zc-106 2 1 c2 100pf 50v 2 1 c4 100pf 50v 2 1 c3 100pf 50v 2 1 c5 100pf 50v c1 2 + 1 100 µ f 10v 2 1 c5 0.1 µ f 25v 2 1 c7 0.1 µ f 25v r1 1 180 Ω j 1/10w 200 Ω j ...

  • Page 84

    - 81 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-3 power supply board (ol1-pcb, rev.6) (1/4).

  • Page 85

    - 82 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-3 power supply board (ol1-pcb, rev.6) (2/4).

  • Page 86

    - 83 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-3 power supply board (ol1-pcb, rev.6) (3/4).

  • Page 87

    - 84 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-3 power supply board (ol1-pcb, rev.6) (4/4).

  • Page 88

    - 85 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-4 power supply board (ol2-pcb, rev.6) (1/4).

  • Page 89

    - 86 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-4 power supply board (ol2-pcb, rev.6) (2/4).

  • Page 90

    - 87 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-4 power supply board (ol2-pcb, rev.6) (3/4).

  • Page 91

    - 88 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-4 power supply board (ol2-pcb, rev.6) (4/4).

  • Page 92

    - 89 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-5 high capacity second paper feeder board (tqsb-2-pcb, rev.1) (1/1) 1 2 3 4 fg fg1 pu optsin-n optsclk-n optsd-p optsdr-n 0vp +30v 0vl +5v 1 2 3 4 5 6 7 8 motor 00-8263-0412-00-000 size zc-105 r3 1 180 Ω j 1/4w 180...

  • Page 93

    - 90 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-6 multi purpose feeder board (olev-pcb, rev.4) (1/2) tr2 cn1 tcs7698-01-201 cn2 tcs7698-01-201 cn3 00-8263-0412-00-000 s3 1 2 3 l2 1 2 l3 1 2 l4 1 2 s1 1 2 s4 1 2 s2 1 2 d4 1 2 rd3.9e-b r9 2 1 r11 1 4 5 6 ic1 10k Ω...

  • Page 94

    - 91 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-6 multi purpose feeder board (olev-pcb, rev.4) (2/2) connector name :00-8263-0412-00-00 parts number :224a3357p0040 ports symbol :cn3 pin no. 1 2 3 4 signal name m-t4 m-t3 m-t2 m-t1 location 01yb 01yb 01yc 01yb con...

  • Page 95

    - 92 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-7 memory expansion bord (mm6-pcb, rev.4) (1/5).

  • Page 96

    - 93 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-7 memory expansion bord (mm6-pcb, rev.4) (2/5) 4.7k 1/10w 4.7k 1/10w 4.7k 1/10w 4.7k 1/10w 4.7k.

  • Page 97

    - 94 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-7 memory expansion bord (mm6-pcb, rev.4) (3/5).

  • Page 98

    - 95 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-7 memory expansion bord (mm6-pcb, rev.4) (4/5).

  • Page 99

    - 96 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-7 memory expansion bord (mm6-pcb, rev.4) (5/5) 4.7k.

  • Page 100

    - 97 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-8 network interface board (mn6-pcb, rev.1) (1/6) nomount.

  • Page 101

    - 98 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-8 network interface board (mn6-pcb, rev.1) (2/6).

  • Page 102

    - 99 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-8 network interface board (mn6-pcb, rev.1) (3/6).

  • Page 103

    - 100 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-8 network interface board (mn6-pcb, rev.1) (4/6).

  • Page 104

    - 101 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-8 network interface board (mn6-pcb, rev.1) (5/6).

  • Page 105

    - 102 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-8 network interface board (mn6-pcb, rev.1) (6/6).

  • Page 106

    - 103 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-9 rs-232c interface board (smif-pcb, rev.5) (1/5).

  • Page 107

    - 104 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-9 rs-232c interface board (smif-pcb, rev.5) (2/5) 4.7k 1/10w 4.7k 1/10w 4.7k 1/10w 4.7k 1/10w.

  • Page 108

    - 105 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-9 rs-232c interface board (smif-pcb, rev.5) (3/5).

  • Page 109

    - 106 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-9 rs-232c interface board (smif-pcb, rev.5) (4/5) 4.7k 1/10w.

  • Page 110

    - 107 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-9 rs-232c interface board (smif-pcb, rev.5) (5/5) 3.3k 1/10w 5.6k 1/10w 5.6k 1/10w 5.6k 1/10w 3.3k 1/10w 0.1u 25 0.1u 25 0.1u 25.

  • Page 111

    - 108 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-10 flash simm (4mb) (fsl-pcb, rev1) (1/1).

  • Page 112

    - 109 - 1 2 34 56 78 9 x y 1 a b c d e f g h a b c d e f g 23 4 5 6 7 8 9 x y figure 5-10 flash simm (8mb) (fsl-2-pcb, rev1) (1/1).

  • Page 113: 6.  Component Parts List

    - 1 - 6. Component parts list.

  • Page 114: Drawing List

    - 2 - drawing list main control board (m5e-pcb, rev. 3) 40750002 operator panel board (olcc-2-pcb, rev. 4) 4ya4130-1001g2 power supply board (ol1-pcb, rev. 6) 40217701 power supply board (ol2-pcb, rev. 6) 40217702 high capacity second (tqsb-2-pcb, rev. 1) 4ya4046-1651g2 paper feeder board multi purp...

  • Page 115

    - 3 - ref. Symbol type/name part no. Q'ty remarks no. M5e-pcb assy. (main control board) rev. 3 (40750002-1/9) c9 fgza3 osc1 cent 36 18 19 1 power 1 26 2 25 1 option bf7 r38 r39 r22 r13 r54 r9 r36 r21 r37 r16 r17 r14 r42 r43 r40 r63 r60 r25 r26 r27 r28 r20 r35 r12 r86 r53 r78 2 51 52 49 1 11 2 head1...

  • Page 116

    - 4 - ref. Symbol type/name part no. Q'ty remarks no. M5e-pcb assy. (main control board) rev. 3 (40750002-2/9) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 d3 d4, d503 d501 d2 d1 r556 r543 r558 r559 r542 r557 r2 r541 r527 r61~r68, r514, r515, r575 r4, r5, r90 610a0332n0001 611a0000n0001 611a0000n0002 6...

  • Page 117

    - 5 - ref. Symbol type/name part no. Q'ty remarks no. 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 r6~r9, r84, r85, r502, r509, r523, r540, r545, r576 r10, r12, r506, r508, r544, r569 r13, r14 r16~r18 r548 r20~r22, r521, r522, r539 r81, r562 r501 r23~r28, r516~r519, r547 r567, r568 r524~r526,r...

  • Page 118

    - 6 - ref. Symbol type/name part no. Q'ty remarks no. 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 r54 r56, r58, r59,r86,r507, r512, r520, r550, r551 r60 r83 r546 r563, r565, r566 r19 r70, r513 r1 r3 r560 r561 r538 r73 r76, r77 r74, r75 r71, r78~r80, r510, r511, r564, r570, r572, r573, r577, r...

  • Page 119

    - 7 - ref. Symbol type/name part no. Q'ty remarks no. 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 rm17~rm21, rm24, rm32, rm33 rm34 rm35, rm36 rm9~rm16 rm27 rm26, rm29~rm31 rm25 c502~c505, c560 c534 c507~c509, c559 c28, c29, c511, c512, c519, c526, c539, c540, c557, c564 c516, c523, c532, c541...

  • Page 120

    - 8 - ref. Symbol type/name part no. Q'ty remarks no. C18, c19, c25, c520, c530, c550, c558 c574 c573 c30 c1 c31 c32 c3, c4 c9, c11 c13 c14 ic11 ic13 ic9 ic10 ic8 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 m5e-pcb assy. (main control board) rev. 3 (40750002-6/9) 7 1 1 1 1 1 1 2 2 1 1 1 1 1 1...

  • Page 121

    - 9 - ref. Symbol type/name part no. Q'ty remarks no. 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 m5e-pcb assy. (main control board) rev. 3 (40750002-7/9) ic4, ic5 ic12 ic1 ic6 ic2 ic3 em9 em1, em2, em4 l1 tr502, tr504 tr501, tr503 tr1 2 1 1 1 1 1 1 3 1 2 2 1 8020003n4613 8162331n0000 8510440n...

  • Page 122

    - 10 - ref. Symbol type/name part no. Q'ty remarks no. 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 m5e-pcb assy. (main control board) rev. 3 (40750002-8/9) cent envelope head2 head1 power dm rm option fan 2ndtray panel osc1 bf1 bf10 fu1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2201001p0...

  • Page 123

    - 11 - ref. Symbol type/name part no. Q'ty remarks no. 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 m5e-pcb assy. (main control board) rev. 3 (40750002-9/9) s3, bf2, bf3, bf7, bf9, bf11 eb1, eb3, eb4 em3, em5~em8 th1 kh-31036-25 lh-31313-158 kh-31036-50 5400500l0102 3n3-hh psw...

  • Page 124

    - 12 - ref. Symbol type/name part no. Q'ty remarks no. Olcc-2-printed circuit board (operator panel board) rev. 4 (4ya4130-1001g2-1/3) d1 r1 ic2 c7 r18 sw1 sw5 r14 r13 r12 r11 r15 r17 r16 r8 r9 r10 r7 r6 r5 r4 r3 r2 c6 sw2 sw6 c5 c2 c4 c3 sw4 sw8 sw3 ic1 sw7 cn1 1 5 2 6.

  • Page 125

    - 13 - ref. Symbol type/name part no. Q'ty remarks no. Olcc-2-printed circuit board (operator panel board) rev. 4 (4ya4130-1001g2-2/3) sel3410g-yz led cc2012ch1h101j 50v cc capacitor (cp) ck2012f1e104z 25v ck capacitor (cp) rm73b2a181j rn resistor (cp) rm73b2a201j rn resistor (cp) rm73b2a682j rn res...

  • Page 126

    - 14 - ref. Symbol type/name part no. Q'ty remarks no. Olcc-2-printed circuit board (operator panel board) rev. 4 (4ya4130-1001g2-3/3) 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 sw1~sw8 cn1 sor-113hs push-button switch zc-106 pc connector 205a1165p1000 224a3591p0060 8 1.

  • Page 127

    - 15 - ref. Symbol type/name part no. Q'ty remarks no. R106 l ps6 ps1 ps5 ps4 ps3 ps2 r121 r120 s44 s3 s12 d134 d129 d102 d103 d133 d132 r122 r102 c102 c103 d104 d105 d136 d123 c115 d106 r114 r118 r119 r112 s52 s38 c52 s59 r71 r116 r115 r103 c104 c105 c107 q101 q108 r101 q106 q107 q103 q54 q57 q53 s...

  • Page 128

    - 16 - ref. Symbol type/name part no. Q'ty remarks no. Ol1-pcb assy. (power supply board) rev. 6 (40217701-2/9) d2 ds1 d7~d10 d101~d104, d106~ d109, d112, d113, d119, d126 d5 d51, d114, d122, d123 d6 d3, d4, d12, d124, d125 d136 d105 d117, d118, d135 d110, d111, d115, d116, d121, d127 d128, d130, d1...

  • Page 129

    - 17 - ref. Symbol type/name part no. Q'ty remarks no. Ol1-pcb assy. (power supply board) rev. 6 (40217701-3/9) r26, r28, r63, r64, r66 r27 r124, r125 r61, r62 r58 r59 r60 r13 r17, r109 r7 r8 r10, r15, r25 r9 r11 r4, r5, r53, r57, r114 r21, r52 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 5 1 ...

  • Page 130

    - 18 - ref. Symbol type/name part no. Q'ty remarks no. Ol1-pcb assy. (power supply board) rev. 6 (40217701-4/9) r6 r51, r102, r108, r120~r122 r116, r119 r32, r67, r68, r115, r118 r101 r75~r77 r24, r78, r79 r80~r84 r65 r69~r71, r74, r113, r117 r72, r73 r33 r34 r110 r111 r19 r20 35 36 37 38 39 40 41 4...

  • Page 131

    - 19 - ref. Symbol type/name part no. Q'ty remarks no. Ol1-pcb assy. (power supply board) rev. 6 (40217701-5/9) 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 r18 r85~r87 r112 r1 r2, r3 r105, r123 r107 r106 r103 r104 r14, r16 r22, r23 c101, c106, c116, c122 c121 c3 c4 1 3 1 1 2 2 1 1 1 1 2 2 4 1...

  • Page 132

    - 20 - ref. Symbol type/name part no. Q'ty remarks no. Ol1-pcb assy. (power supply board) rev. 6 (40217701-6/9) 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 c5, c12, c16, c21, c51, c52, c57, c58, c60, c68~c70, c71, c109, c110, c118~c120 c59 c13, c54, c55 c14, c20 c9 c10 c8 c22 c17, c18 c56 c11...

  • Page 133

    - 21 - ref. Symbol type/name part no. Q'ty remarks no. Ol1-pcb assy. (power supply board) rev. 6 (40217701-7/9) 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 c23 q1 q5 q3, q109, q111 q2, q6, q7, q58~q62, q110 q52 d1 q101~q105 q106, q108 q107 q4, q53~q57 pc1 ps1~ps6 ic1 ic2 1 1 1 3 9 1 1 5 2 ...

  • Page 134

    - 22 - ref. Symbol type/name part no. Q'ty remarks no. Ol1-pcb assy. (power supply board) rev. 6 (40217701-8/9) 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 ic4 ic5 ic6 ic7 osc1 l1 l2 l3 l101 t2~t6 cn1 cn2 cn3 1 1 1 1 1 1 1 1 1 5 1 1 1 324p analog-biplin - 358p analog-biplin -...

  • Page 135

    - 23 - ref. Symbol type/name part no. Q'ty remarks no. Ol1-pcb assy. (power supply board) rev. 6 (40217701-9/9) 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 f1 f2 f3 sw1 sw2 inlet s1~s15, s17~s21, s24, s29, s40, s44, s79, s91 s22, s23, s25~s28, s30~s39, s49 s41~s43, s45~s48, s...

  • Page 136

    - 24 - ref. Symbol type/name part no. Q'ty remarks no. R106 l ps6 ps1 ps5 ps4 ps3 ps2 r121 r120 s44 s3 s12 d134 d129 d102 d103 d133 d132 r122 r102 c102 c103 d104 d105 d136 d123 c115 d106 r114 r118 r119 r112 s52 s38 c52 s59 r71 r116 r115 r103 c104 c105 c107 q101 q108 r101 q106 q107 q103 q54 s87 s88 c...

  • Page 137

    - 25 - ref. Symbol type/name part no. Q'ty remarks no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 ol2-pcb assy. (power supply board) rev. 6 (40217702-2/10) d2 ds1 d7~d10 d101~d104, d106~d109, d112, d113, d119, d126 d5 d51, d114, d122, d123 d6 d3, d4, d12, d124, d125 d136 d105 d117, d118, d135 d110, d...

  • Page 138

    - 26 - ref. Symbol type/name part no. Q'ty remarks no. 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 ol2-pcb assy. (power supply board) rev. 6 (40217702-3/10) r26, r28, r63,r64, r66 r27 r124, r125 r61, r62 r58 r59 r60 r13 r17, r109 r7 r8 r10, r15, r25 r9 r11 r4, r5, r53, r57, r114 r21, r52 rd16...

  • Page 139

    - 27 - ref. Symbol type/name part no. Q'ty remarks no. 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 ol2-pcb assy. (power supply board) rev. 6 (40217702-4/10) r6 r51, r102, r108, r120~122 r116, r119 r32,r67, r68, r115, r118 r101 r75~r77 r24, r78, r79 r80~r84 r65 r69~r71, r74, r113, r117 r72, r7...

  • Page 140

    - 28 - ref. Symbol type/name part no. Q'ty remarks no. 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 ol2-pcb assy. (power supply board) rev. 6 (40217702-5/10) r18 r85~r87 r112 r1 r2, r3 r105, r123 r107 r106 r103 r104 r14, r16 r22, r23 c101, c106, c116,c122 c121 c3 c4 rnl1/4c3f1.0kohm res-met rn...

  • Page 141

    - 29 - ref. Symbol type/name part no. Q'ty remarks no. 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 ol2-pcb assy. (power supply board) rev. 6 (40217702-6/10) c5, c12, c16,c21, c51, c52, c57,c58, c60, c68~c71, c109, c110, c118~c120 c59 c1, c2 c13, c54, c55 c14, c20 c9 c10 c8 c22 c17, c18 c56 c1...

  • Page 142

    - 30 - ref. Symbol type/name part no. Q'ty remarks no. 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 ol2-pcb assy. (power supply board) rev. 6 (40217702-7/10) c11 c23 q1 q5 q3, q109, q111 q2, q6, q7, q58~q62, q110 q52 d1 q101~q105 q106, q108 q107 q4, q53~q57 pc1 ps1~ps6 ic1 rd16xr/ck92c1h681...

  • Page 143

    - 31 - ref. Symbol type/name part no. Q'ty remarks no. 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 ol2-pcb assy. (power supply board) rev. 6 (40217702-8/10) ic2 ic4 ic5 ic6 ic7 osc1 l2 l3 l101 l1 t2~t6 cn1 cn2 cn3 lc26023a-na5 digital ic-mos- 324p analog-biplin - 358p analog-...

  • Page 144

    - 32 - ref. Symbol type/name part no. Q'ty remarks no. 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 ol2-pcb assy. (power supply board) rev. 6 (40217702-9/10) f1 f3 sw1 sw2 inlet s1~s15, s17~s21, s24, s29, s40, s44, s79, s91 s22, s23, s25~s28, s30~s39, s49 s41~s43, s45~s48, s50...

  • Page 145

    - 33 - ref. Symbol type/name part no. Q'ty remarks no. S80~s85, s87~s90 s86, s93, s94 s74, s92, s95~s97 137 138 139 short wire short wire short wire 10 3 5 ta-0.6 ta-0.6 ta-0.6 ol2-pcb assy. (power supply board) rev. 6 (40217702-10/10).

  • Page 146

    - 34 - ref. Symbol type/name part no. Q'ty remarks no. Tqsb-2-printed circuit board (high capacity second paper feeder board) rev. 1 (4ya4046-1651g2-1/4) r514 c508 r513 c507 c505 c504 r512 c503 r511 r506 r505 r504 r510 r509 c502 r508 r507 r518 r517 c516 r515 c506 bf502 bf501 r503 c501 r502 r501 d1 d...

  • Page 147

    - 35 - ref. Symbol type/name part no. Q'ty remarks no. D1~d3 d5 d4 r513, r514 r1, r2 r503, r511, r512 r3, r4 r501, r502, r508~r510, r515~r518 r506 r505 r507 r504 rm1 em01z/sm1xn02/dsm1d2 rectifier d1 rd3.9e-b zener-d1 1s953/1s2075k/1s2473 signal d1 rm73b2a473j rn resistor (cp) msf1/2b0.51 Ω j rs res...

  • Page 148

    - 36 - ref. Symbol type/name part no. Q'ty remarks no. 1 1 1 4 1 3 1 1 1 2 2 2 tqsb-2-printed circuit board (high capacity second paper feeder board) rev. 1 (4ya4046-1651g2-3/4) 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 c1 c2 c3 c503, c504, c507, c508 c502 c501, c505, c506 ic3 ic1 ic2 bf501...

  • Page 149

    - 37 - ref. Symbol type/name part no. Q'ty remarks no. 381a1025b0002 540a2208s1102 224a3357p0040 224a3052p0080 5kh-31036-25 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 osc1 f1 motor pu s3 cst4.00mgw ceramic oscillator 251-001 fuse 00-8263-0412-00-000 pc connector il-s-8p-s2t2-ef pc connector ...

  • Page 150

    - 38 - ref. Symbol type/name part no. Q'ty remarks no. Olev-printed circuit board (multi purpose feeder board) rev. 4 (4ya4121-1014g11-1/4) f1 c11 c9 s3 s1 tr2 tr1 c2 c7 c10 cn3 l2 s4 c3 r4 osc1 d5 r2 ic1 rm1 ic2 r14 c1 c5 r3 r15 c6 c4 r16 ic3 r13 r10 r7 r9 r8 r5 r6 r12 c8 r17 sen2 r18 l4 cn2 l3 r19...

  • Page 151

    - 39 - ref. Symbol type/name part no. Q'ty remarks no. Olev-printed circuit board (multi purpose feeder board) rev. 4 (4ya4121-1014g11-2/4) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 d1, d2, d5 d4 d3 r15, r16 r18, r19 r3~r6 r2 r7~r10, r14 r12 r17 r13 rm1 c10 em01z/sm1xn02/dsm1d2 rectifier diode rd3.9...

  • Page 152

    - 40 - ref. Symbol type/name part no. Q'ty remarks no. 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 c11 c2 c1 c3~c6 c7~c9 ic3 ic1 ic2 sen2 tr1, tr2 osc1 s1, s3, s4, l2~l4 f1 cn2 10ms5-33m 10v ce capacitor 33 µ f rpe122-127e334m50 ck capacitor 0.33 µ f cc2012sl1h471j 50v cc capacitor (cp) ck201...

  • Page 153

    - 41 - ref. Symbol type/name part no. Q'ty remarks no. 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 olev-printed circuit board (multi purpose feeder board) rev. 4 (4ya4121-1014g11-4/4) 224a3357p0040 1 cn3 00-8263-0412-00-000 pc connector.

  • Page 154

    - 42 - ref. Symbol type/name part no. Q'ty remarks no. C26 c3 c4 c5 c22 d2 r8 r10 c2 c20 r6 c1 r7 r18 r19 r20 r21 r22 r23 r24 r25 r26 r27 r28 r5 r2 r1 c43 r16 cn1 r11 r9 c21 c42 c18 c10 c23 c6 em1 c7 c13 rm6 rm7 rm4 rm5 rm2 rm3 rm1 q1 d1 q5 q2 q3 q4 fg1 c19 c17 c16 bf1 simm2 simm1 + + + 1 2 71 72 1 ...

  • Page 155

    - 43 - ref. Symbol type/name part no. Q'ty remarks no. Mm6-pcb assy. (memory expansion board) rev. 4 (40369105-2/3) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 r8~r11 r18~r28 r1, r2, r5, r6, r7 r16 rm1~rm7 c20, c21 c22, c26, c42, c43 c23 c1~c7, c10, c13, c18 c16, c17, c19 q1~q5 em1 rm73b2a220j res-met...

  • Page 156

    - 44 - ref. Symbol type/name part no. Q'ty remarks no. Mm6-pcb assy. (memory expansion board) rev. 4 (40369105-3/3) 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 514260jp-60 memory-mosdram-s pq100a2ma connector-pcb - zbf253d-01 filter-pw line - 2-176438-7 socket-semicon - or 11088-1 socket-semi...

  • Page 157

    - 45 - ref. Symbol type/name part no. Q'ty remarks no. Bf1 osc1 cn1 em1 em2 rm1 rm7 rm6 rm5 rm4 rm3 rm2 ic2 ic3 ic4 ic5 ic6 ic11 ic10 ic9 ic8 ic7 simm2 simm1 cn2 bf5 bf4 bf3 r1 c4 c5 c6 c7 t1 bf2 1 1 35 2 36 1 39 49 100 50 51 1 52 2 35 2 36 3 71 38 72 3 71 38 72 4 2 8 bf6 c2 ic1 c1 r5 r4 r3 r2 r9 r8...

  • Page 158

    - 46 - ref. Symbol type/name part no. Q'ty remarks no. Mn6-pcb assy. (network interface board) rev. 1 (40755404-2/4) r505, r509 r1 r515 r516 r517 r512, r513 r510 r511 r10~r20 r506 r6~r9, r514, r518, r520~r523 r519 r2~r5, r524, r525, r530 r532, c547~c549 rm1~rm7 3235010f2439 323a5003f0101 323a5003f03...

  • Page 159

    - 47 - ref. Symbol type/name part no. Q'ty remarks no. Mn6-pcb assy. (network interface board) rev. 1 (40755404-3/4) 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 cc2012ch1h100d 50v cap-ceramic -c cc2012ch1h101j 50v cap-ceramic -c cc2012ch1h180j 50v cap-ceramic -c cc2012ch1h220j 50v cap-ceramic...

  • Page 160

    - 48 - ref. Symbol type/name part no. Q'ty remarks no. Mn6-pcb assy. (network interface board) rev. 1 (40755404-4/4) 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 7024631n2001 8163622n0000 8550378n0001 342a1009p2222 245a1372p0720 or 2451002p0720 223a3435p0001 224a3515p1000 384a2127b0004 3652002...

  • Page 161

    - 49 - ref. Symbol type/name part no. Q'ty remarks no. Jp3 jp4 em1 c16 c15 q5 q6 q7 q8 q4 c17 c4 r38 r37 r8 r9 r10 r11 r32 r33 r34 r35 r15 r14 r13 r12 r24 r25 r26 r27 r31 r30 r29 r28 r16 r17 r18 r19 r23 r22 r21 r20 r5 r2 r6 r1 c29 c27 c28 c26 c25 c24 c23 c11 c13 c8 c7 c6 c5 c12 c14 simm1 simm2 q11 c...

  • Page 162

    - 50 - ref. Symbol type/name part no. Q'ty remarks no. Smif-serial memory interface pcb (rs232c interface board) rev. 5 (0025304-2/4) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 r1, r2, r5, r6 r8~r31 r32~r35, r37, r38 r72 jp1~jp4 r74~r76 c11, c12, c15 c4~c8, c13, c14, c16 c18~c20 c17 rm73b2a472j rn re...

  • Page 163

    - 51 - ref. Symbol type/name part no. Q'ty remarks no. Smif-serial memory interface pcb (rs232c interface board) rev. 5 (0025304-3/4) 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 c21 c22 c23~c29 q4~q8 q11 d1, d2 cn1 cn2 simm1, simm2 ck2012b1h561k 50v ck capacitor (cp) ck2012b1h102k 50v ck capa...

  • Page 164

    - 52 - ref. Symbol type/name part no. Q'ty remarks no. 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 smif-serial memory interface pcb (rs232c interface board) rev. 5 (0025304-4/4) bf emi zbf253d-01 bead filter dss306-oafz103n emi filter adhesive barcode label 1 1 1 377a1115p1309 342a1009p3103 4...

  • Page 165

    - 53 - ref. Symbol type/name part no. Q'ty remarks no. R3 c501 c503 c504 c500 c502 r1 r2 r0 e2rom ter1 rom1 rom0 1 1 24 48 25 1 24 48 25 72 rom3 rom2 fsl-pcb (flash simm 4mb) rev. 1 (40405419-1/2).

  • Page 166

    - 54 - ref. Symbol type/name part no. Q'ty remarks no. Fsl-pcb (flash simm 4mb) rev. 1 (40405419-2/2) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 r0~r3 c500~c504 rom0~rom3 e2rom rm73b2a103j res-met rn -c ck2012f1e104z 25v cap-ceramic -c mbm29f080a-90pftn memory-moseepr -s nm93c66em8x memory-moseepr -s...

  • Page 167

    - 55 - ref. Symbol type/name part no. Q'ty remarks no. Fsl-2-pcb (flash simm 8mb) rev. 1 (40405420-1/2) r3 c501 c503 c504 c500 c502 r1 r2 r0 e2rom ter1 rom1 rom0 1 1 24 48 25 1 24 48 25 72 rom3 rom2.

  • Page 168

    - 56 - ref. Symbol type/name part no. Q'ty remarks no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 r0~r3 c500~c504 e2rom rom0~rom3 rm73b2a103j res-met rn -c ck2012f1e104z 25v cap-ceramic -c nm93c66em8x memory-moseepr -s mbm29f016a-90pftn memory-moseepr -s 323a5003j0103 303a6008z2104 8162330n0000 81646...

  • Page 169

    Oki data corporation overseas sales & 4-11-22, shibaura, minato-ku, tokyo 108-8551, japan marketing department: tel: +81 (japan)-3 (tokyo)-5445-6159 fax: 81-3-5445-6188 american sales/ okidata division of oki america inc. Service support center: 532 fellowship rd. Mt. Laurel, n. J., 08054 u. S. A. T...