1. DL manuals
  2. Pacific
  3. Scrubber
  4. Proteus 26
  5. Operating & Maintenance Instructions

Pacific Proteus 26 Operating & Maintenance Instructions

Other manuals for Proteus 26: Operating & Maintenance Instructions
Manual is about: Automatic

Summary of Proteus 26

  • Page 1

    Page 1 of 17 proteus 26 & 26ba operating & maintenance instructions read this manual this operator's manual has important information for the use and safe operation of this machine. Read this manual carefully before starting the machine. Keep this manual and tell all operators to read this manual. I...

  • Page 2: Safety Instructions

    Page 2 of 17 safety instructions 1) you must have training in the operation of the machine before using it. Read the instruction book. If you do not understand any instruction, ask your supervisor. 2) make sure all labels, decals, warnings, cautions and instructions are fastened to the machine. 3) r...

  • Page 3

    Page 3 of 17 symbols used on the automatic scrubber water valve indicator brush drive motor control switch brush base lifting lever vacuum motor control switch squeegee lift lever indicator battery charge indicator parking brake indicator handle bar height adjustment lever off / on key switch indica...

  • Page 4: Machine Preparation

    Page 4 of 17 machine preparation 1) unpacking the machine a) take off the outer packaging. B) the machine is fastened to the pallet with wooden wedges that block the wheels. Remove wedge and tie down straps. C) using a ramp, pull the machine off the pallet. 2) battery installation a) lift the recove...

  • Page 5: Machine Preparation

    Page 5 of 17 machine preparation 3) battery installation (cont.) the battery charger’s connector fits into the battery connector (1). 4) charging the batteries never allow the batteries to completely discharge. Recharge them within a few minutes after the battery indicator starts flashing. Never lea...

  • Page 6: Machine Preparation

    Page 6 of 17 machine preparation 5) battery charge level indicator the batteries’ indicator is digital with 4 display levels and a flashing one. The numbers, which appear on the display, show the approximate charge level. 4 represents a full charge and 0 represents discharged and the batteries must ...

  • Page 7: Machine Preparation

    Page 7 of 17 machine preparation 8) adjusting squeegee height the height from floor to squeegee should be adjusted based on blade wear. Rotate the knobs (2) counter-clockwise to lift squeegee and clockwise to lower it. Note: rotate the right and left adjusting knobs until the squeegee is positioned ...

  • Page 8: Machine Preparation

    Page 8 of 17 machine preparation 11) solution tank remove water inlet cover plug and confirm the solution filter, which is located on the bottom left side, is properly assembled. 12) solution water fill the solution tank with clean water at a temperature not higher than 50°c / 122°f. Add the proper ...

  • Page 9: Machine Operation

    Page 9 of 17 machine operation 1) connect machine connector (2) to the battery connector (1). 2) turn key (1) clockwise to on. Signal light (3) will illuminate indicating that the batteries are charged. If the indicator is flashing the batteries need to be charged. 3) turn on the water solenoid valv...

  • Page 10: Machine Operation

    Page 10 of 17 machine operation 10) machine movement these machines are equipped with driven traction wheels or brush assist propulsion. The machines with driven wheels have two speeds forward and one speed backwards. To move either style machine forward, turn the key on, wait for 3 seconds and then...

  • Page 11

    Page 11 of 17 upon completion of machine use after finishing your work and before any type of maintenance is done, it is necessary to do the following: 1) close the water valve with lever (1). 2) raise the brush base with lever (2). 3) lift the squeegee with lever (3). Note: the squeegee blades can ...

  • Page 12: Daily Machine Maintenance

    Page 12 of 17 daily machine maintenance cleaning the recovery tank 1) empty the recovery tank by removing the plug from the drain hose. Warning: use gloves for protection from contact with dangerous solution. 2) lift the cover of the recovery tank. 3) take off the vacuum cover by rotating it counter...

  • Page 13: Daily Machine Maintenance

    Page 13 of 17 daily machine maintenance cleaning the squeegee to obtain the best drying results, keep the squeegee clean. To clean the squeegee it is necessary to: 13) remove the vacuum hose from the squeegee. 14) press release latch (1) toward the center of the machine. Remove the squeegee assembly...

  • Page 14: Daily Machine Maintenance

    Page 14 of 17 daily machine maintenance brush / pad driver removal (cont.) 27) rotate each brush until they come off the brush plate. The figure shows the direction to rotate each of the brushes to release them from the machine. Battery compartment cleaning 28) use the hose under the solution tank, ...

  • Page 15: Weekly Machine Maintenance

    Page 15 of 17 weekly machine maintenance cleaning the squeegee hose to obtain the best drying results, keep the squeegee hose clean. To clean the squeegee hose it is necessary to: 1) take off the vacuum hose from its vacuum port on the squeegee. 2) remove the other end of the vacuum hose from the re...

  • Page 16: Trouble Shooting Guide

    Page 16 of 17 trouble shooting guide 1) insufficient water to the brushes a) make sure the water valve is open (lever 1). B) confirm that there is water in the solution tank. 2) the machine does not clean satisfactorily a) check the condition of the brushes or pads and replace them if necessary. B) ...

  • Page 17

    02/2007 page 17 of 17 pn 865615 warranty policy pacific limited warranty the pacific proteus 26 and 26ba have been manufactured, tested and inspected in accordance with specific engineering requirements. This machine is warranted to be free from defects in workmanship and materials for periods as fo...