1. DL manuals
  2. Panasonic
  3. Fax Machine
  4. Panafax UF-7000
  5. Service Handbook

Panasonic Panafax UF-7000 Service Handbook

Other manuals for Panafax UF-7000: Network Connection, Operating Instructions Manual, Fax Manual

Summary of Panafax UF-7000

  • Page 1

    Order number: mgcs041006c0 h13 facsimile uf-7000/8000 uf-7100/8100 [ version 2.0 ] this service information is designed for experienced repair technicians only and is not intended for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential...

  • Page 2

    2 the contents of this service manual and the specifications are subject to change without notice. Panasonic communications co., ltd. Reserves the right to make improvements in the product design without reservation and without notice. Published in japan. Information regarding lead-free (pbf) solder...

  • Page 3: Important Notice

    3 important notice please read this notice completely before installing any optional accessories. As failure to properly install the additional board or connector with the power on could damage the machine's sdr or sc board. Please follow the instructions below: 1. It is essential that you turn off ...

  • Page 4: Caution:

    4 important notice for installation caution: depending on your machine's model, it may weight approximately 48.50 lb (22.0 kg) without any options. To prevent injuries, use the appropriate number of personnel and lift or move the machine as illustrated. Do not lift the machine by the paper tray as i...

  • Page 5: Precautions

    5 power and ground connection cautions ensure that the plug connection is free of dust. In a damp environment, a contaminated connector can draw a significant amount of current that can generate heat and eventually cause fire over an extended period of time. Always use the power cord provided with y...

  • Page 6

    6 never touch a power cord with wet hands. Danger of electric shock exists. If the power cord is broken or insulated wires are exposed, replace immediately with a specified cord only. Using a damaged cord can cause fire or electric shock. Stop operation immediately if your machine produces smoke, ex...

  • Page 7

    7 do not place a magnet near the safety switch of the machine. A magnet can activate the machine accidentally resulting in injuries. Do not use a highly flammable spray or solvent near the machine. It can cause a fire. When copying a thick document, do not use excessive force to press it against the...

  • Page 8

    Table of contents 8 specifications table ................................ 9 1.1. Fax, printer, network scanner and internet fax functions ............................. 9 1.2. System combination.............................. 23 1.3. Options list ............................................ 24 mainten...

  • Page 9: 1 Specifications Table

    9 nov 2004 ver. 2.0 uf-7100/8100 uf-7000/8000 1 specifications table 1.1. Fax, printer, network scanner and internet fax functions 1.1.1. Fax function items description remarks uf-7000/7100 uf-8000/8100 main specifications 1 compatibility super g3 / g3 itu-t std & non-std 2 modem speed 33.6 - 2.4kbp...

  • Page 10

    10 uf-7100/8100 nov 2004 ver. 2.0 uf-7000/8000 scanner mechanism 1 scanning device cis (adf) 2 scanning resolution / speed std: 203 x 98 (8 x 3.85) dpi x lpi (pels/mm x lines/ mm) ltr : 1.4 sec a4 : 1.5 sec ltr : 0.7 sec a4 : 0.7 sec excludes: initializing time, adf slipping factor, and data xmt tim...

  • Page 11

    11 nov 2004 ver. 2.0 uf-7100/8100 uf-7000/8000 memory 1 fax memory standard memory (flash) 3 mb (180 pages) 12 mb (720 pages) itu-t image no.1 (a4, std resolution) (refer to 1.1.5.) optional memory (sd memory card) 32 mb to 512 mb (max. 1,020 to 12,750 pages) 2 printer page memory 32 mb 3 sort memor...

  • Page 12

    12 uf-7100/8100 nov 2004 ver. 2.0 uf-7000/8000 consumables 1 toner cartridge yield: 5 k (5% coverage), 6 k max average yield is based on 5% coverage of the printable area with repetitive printing of 10 pages (letter/a4 size, single side printing, default density). The yield of a toner cartridge vari...

  • Page 13

    13 nov 2004 ver. 2.0 uf-7100/8100 uf-7000/8000 11 full number dialing (buffered dialing) yes max. 50 stations 12 direct dialing (monitor dialing) yes voice mode 13 automatic redialing yes up to 15 times at 0 to 15 min. Intervals 14 manual redialing yes pressing the redial/pause button 15 line monito...

  • Page 14

    14 uf-7100/8100 nov 2004 ver. 2.0 uf-7000/8000 reception features 1 substitute reception yes 2 fixed reduction yes ltr/a4/lgl: 70 - 100% (in 1% steps), top & left alignment 3 auto reduction yes ltr/a4/lgl: 70 - 100% (in 1% steps), top & left alignment 4 overlap printing yes page end approx. 0.51 in ...

  • Page 15

    15 nov 2004 ver. 2.0 uf-7100/8100 uf-7000/8000 copy features 1 first copy time letter 25 sec. 19 sec. A4 26 sec. 2 copy speed letter approx. 15 cpm approx. 19 cpm paper feed: 1st paper tray; paper exit: to exit tray; continuous copy mode. A4 approx. 14 cpm approx. 18 cpm 3 single copy yes 4 multiple...

  • Page 16

    16 uf-7100/8100 nov 2004 ver. 2.0 uf-7000/8000 special communications 1 password xmt / rcv no 2 selective reception no tsi check 3 relay xmt request no 4 relay xmt center no 5 confidential xmt / polling no 6 confidential center no 7 mailbox xmt / polling no 8 mailbox center no 9 file xmt no 10 recei...

  • Page 17

    17 nov 2004 ver. 2.0 uf-7100/8100 uf-7000/8000 1.1.2. Printer function items description remarks uf-7000/7100 uf-8000/8100 interface 1 centronics parallel i/f no 2 lan (network) yes ethernet 10base-t/100base- tx 3 usb port yes usb1.1 4 ieee-1394 no firewire printer function 1 printing size lgl / ltr...

  • Page 18

    18 uf-7100/8100 nov 2004 ver. 2.0 uf-7000/8000 18 output to separate tray for printing, fax, copy no 19 font yes requires optional pcl6 emulation kit 20 secure mailbox yes requires optional sd memory card (256 mb or 512 mb). Max. 10 mailboxes. Items description remarks uf-7000/7100 uf-8000/8100

  • Page 19

    19 nov 2004 ver. 2.0 uf-7100/8100 uf-7000/8000 1.1.3. Network scanner function items description remarks uf-7000/7100 uf-8000/8100 interface 1 centronics parallel i/f no 2 lan (network) yes ethernet 10base-t/100base- tx 3 usb port no 4 ieee-1394 no firewire network scanning function 1 scanning devic...

  • Page 20

    20 uf-7100/8100 nov 2004 ver. 2.0 uf-7000/8000 1.1.4. Internet fax function items description remarks uf-7000/7100/8000/8100 main specifications 1 communication protocols smtp / pop3 / mime 2 max. Modem speed na 3 coding scheme jbig/mmr/mr/mh 4 file format tiff / pdf selectable (pdf formats are used...

  • Page 21

    21 nov 2004 ver. 2.0 uf-7100/8100 uf-7000/8000 lan features 1 internet fax communication yes 2 internet mail reception yes 3 internet fax server features internet fax relay xmt yes internet fax → internet fax → g3fax email relay xmt yes pc → internet fax → g3fax received fax / email forward yes loca...

  • Page 22

    22 uf-7100/8100 nov 2004 ver. 2.0 uf-7000/8000 1.1.5. Sd memory card sd memory card format structure and allocation by function note: 1. This function is available only when an sd memory card is installed. 2. Max. Number of pages is based on itu-t image no.1 (a4, standard resolution). 3. Fax/interne...

  • Page 23

    23 nov 2004 ver. 2.0 uf-7100/8100 uf-7000/8000 1.2. System combination sd memory card (32 mb - 512 mb) main pc board (sc) 2nd paper feed module option option standard configuration panel (pnl pc board) handset kit option pcl6 emulation option usb interface gdi printer 10/100 ethernet interface autom...

  • Page 24

    24 uf-7100/8100 nov 2004 ver. 2.0 uf-7000/8000 1.3. Options list ■ options ■ supplies note: 1. Pcl6 is a page description language of the hewlett-packard company. 2. The part name(s) / part number(s) differ depending on the models and the destinations. 3. Genuine sd memory cards depict an sd logo on...

  • Page 25

    25 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 2 maintenance, adjustments and check points 2.1. Preventive maintenance preventive maintenance is performed at specific intervals and consists of machine cleaning and parts replacement. It is essential to perform these service activities properly and at...

  • Page 26

    26 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4 laser handling precautions the optical laser system employed by this photocopier is completely sealed by a protective housing and an external cover. Therefore, the laser beam will not stray or leak during photocopying operation. However, when servicin...

  • Page 27

    27 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 2.2. Required tools 2.2.1. Preventive maintenance method no. Tools no. Tools 1 soft cloth 7 pliers 2 isopropyl alcohol 8 cotton swab 3 phillips screwdriver (#2) 9 brush 4 stubby phillips screwdriver (#2) 10 ks-660 - conductive grease (available from shi...

  • Page 28

    28 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 2.3. Preventive maintenance points adf & scanner: front view printer: left side view pick up roller separation roller adf pad feed roller 1 3 4 lsu toner cartridge opc drum pick up roller 5 bias transfer roller (btr) 7 separation pad 6 pick up roller 8 ...

  • Page 29

    29 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 2.4. Preventive maintenance check list the chart outlined below is a general guideline for maintenance. The list is for an average usage of 50 transmitted and received documents per day. Needless to say, the environmental conditions and actual use will ...

  • Page 30

    30 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 2.5. Updating the firmware the quick and easy methods of updating the firmware are to use the network firmware program tool (fup) using ethernet lan port and a crossover cable or to use a master sd memory card. The network fup tool version must be 3.Xx ...

  • Page 31

    31 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 slot 1. The firmware (3) and (4) are assigned as rom code (c). When using sd memory card (32 mb to 512 mb), the 8 mb program (c) can be written onto one card. C. 2nd g3 pc board firmware the 4 mb program memory (f-rom) is integrated on the 2nd g3 pcb. T...

  • Page 32

    32 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 2.5.2. Updating through a lan port (the quick and easy method) the firmware code can be easily updated when the main unit is connected to a lan. The network firmware update tool can also be used by connecting to the machine using a crossover cable, if t...

  • Page 33

    33 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 note: 1. Manual mode must be used, when updating the designated version of the firmware or changing the type of the firmware. Please refer to the section 2.2, "setting up the network firmware update tool, file selection tab" of the operating instruction...

  • Page 34

    34 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4) upgrading the main unit's firmware code start the local firmware update tool and select the following firmware code parent file folder in the c:\panasonic\panasonic-fup\data folder, and select the firmware code type then follow the display instructio...

  • Page 35

    35 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 11. Remove the master firmware sd memory card from the machine. 12. Reconnect the telephone line, lan and/or usb cables. 13. Turn the power switch on the back of the machine to the on position. 14. Reprogram the f5 & f6 parameters according to the lists...

  • Page 36

    36 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 3) preparing the master firmware sd memory card 1. Insert the sd memory card (32 mb to 512 mb) into the sd memory card slot. 2. Perform the sd memory card firmware writing tool. 3. After all firmware codes are copied, remove the sd memory card from the ...

  • Page 37

    37 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 12. Press "stop" first and then press "function" + "clear" keys sequentially to return to standby. 13. Turn the power switch on the back of the machine to the off position. 14. Reconnect the telephone line, lan and/or usb cables. 15. Turn the power swit...

  • Page 38

    38 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 2nd g3 : uf-8k g3b a a vxxxxx yc firmware version (v1xxxx) aa: fixed 2nd g3 model number yc: fixed.

  • Page 39

    39 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 2.6. Adjusting the printer registration, lsu image side to side when installing the paper tray option, the following lsu image side to side adjustment may be required. The printer registration is adjusted at the factory. If copy image is abnormal, espec...

  • Page 40

    40 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 2.6.3. Lsu image side to side adjustment for the adu 1. Insert letter or a4 size paper into the 1st tray and change the tray setting to the appropriate paper size. Empty all the remaining trays (including the bypass tray) to disable them. 2. Press “func...

  • Page 41: 3 Troubleshooting

    41 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 3 troubleshooting 3.1. Error codes (for copier) the self-diagnostic functions detect troubles in the important components of the copier. When trouble occurs, the machine stops. Note: some codes are not used in the uf-7000/7100/8000/8100 and are reserved...

  • Page 42

    42 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 3.1.1.1. Low toner messages / operation the toner cartridge yield is approximately 5,000 pages using letter or a4 size paper and 5% black coverage, however, the maximum yield will not exceed 6,000 pages. The machine controls the printer to maintain good...

  • Page 43

    43 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 3.1.2. Jam error codes (j code) section jam location a adf b paper transport / exit area c paper entry area jam error codes (j codes) table code contents section j00 the registration sensor did not detect paper within a predetermined time after paper st...

  • Page 44

    44 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 • sensor and switch location.

  • Page 45

    45 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 3.1.3. Mechanical error codes (e code) e1: optical unit error code function check points e1- 22 polygon motor synchronization 1. Engine pcb connector is disconnected. 2. Engine pcb is defective. 3. Laser unit is defective. 4. Lvps connectors is disconne...

  • Page 46

    46 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 note: these error codes will appear only when the optional accessories are installed. E5- 40 sort memory abnormal 1. Sort memory defective. 2. Sc pcb connector is disconnected. 3. Sc pcb defective. E7: optional unit error code function check points e7- ...

  • Page 47

    47 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 3.2. Information code table (for facsimile) fax information codes code mode phase description of problem cause 001 rcv copy c, d leading edge of the recording paper fails to reach the timing sensor. (1st tray) recording paper jam. Timing sensor abnormal...

  • Page 48

    48 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 400 xmt b t1 timer (35 ± 5 sec.) elapsed without detecting 300 bps signal. Incorrect number was dialed and the start button was pushed. Telephone line was disconnected while dialing. Sc pcb or fxb pcb are defective. Receiver is defective. (it may only b...

  • Page 49

    49 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 412 g3 rx b, d no response within 12 seconds in nss/dcs/mps wait state. (after transmitting ftt) transmitter is defective. Sc pcb is defective. 414 rcv (polling) b no response received after transmitting 3rd nsc. Password does not match between transmit...

  • Page 50

    50 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 494 rcv c interval between two eols was more than 10 sec. When receiver received message data. Transmitter is defective. Line quality is poor. (eol is damaged due to line noise) sc pcb or fxb pcb are defective. 495 xmt rcv c during reception, cd turned ...

  • Page 51

    51 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 582 xmt b sub-address sep (for polling) transmission to a unit that has their dis bit 47 (nsf bit 130) off. Sub-address transmission to a unit that has no sub-address function. 601 xmt adf door was opened during adf transmission. 623 xmt a no original w...

  • Page 52

    52 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 718 xmt lan page memory overflow occurred while receiving printing data. The paper size selected within your application to print is larger than the paper size loaded in the tray(s). Check the document size and resolution. Ask originator to re-send in a...

  • Page 53

    53 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 note: when 2nd g3 option is installed, check fxb pcb or g3b pcb. 814 conf. Xmt conf. Polling relay comm. Pstn the remote station does not have relay xmt nor confidential communication capability. 815 conf. Rcv pstn mailbox full. 816 conf. Polled pstn th...

  • Page 54: 4 Service Modes

    54 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4 service modes 4.1. Service modes (for copier) these service modes are provided to assist the technician in checking for abnormalities in the copier and a means of making adjustments to the input/output of major components. Caution: the factory default...

  • Page 55

    55 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 f9 unit maintenance fax service mode service alert tel # firmware version print device info. Service modes (for copier) service mode item function.

  • Page 56

    56 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 f5 / f6 information list (sample) * * * * * * * * * * - f 5 / f 6 i n f o r m a t i o n l i s t - * * * * * * d a t e m m m - d d - y y y y * * * t i m e 1 2 : 0 1 * * * p . 0 1 f5-00 . . . . . F5-50 auto contrast adj. Yes f5-01 frequency desired 60hz f...

  • Page 57

    57 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 2.Firmware version sc : bat208xxau 1.Machine information machine name : uf-8000 mac address : 08002301d3e5 serial number : sc boot : v803 pnl : v010018 scanner(sdr) : v00000 printer : v00029 fax modem : ver 0801 g3b board : pdl font1 : cav00000b sc2 : c...

  • Page 58

    58 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 f7 total counter list (sample) f7-01 key operator id code : 000 f7-02 total count : 295 f7-03 pm count : 295 f7-04 scanner pm count : 61 f7-05 . . . . . : f7-06 opc drum count : 295 f7-07 process unit count : 295 f7-08 adf pm count : 50 f7-09 . . . . . ...

  • Page 59

    59 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.1.3. F4 mode: input/output status test set the machine to service mode and press "4" key on the keypad. ↓ press the "start" key. ↓ select “1:check input“ or “2:check output“ to activate the test then press "start" key. ↓ press "stop" key to cancel the...

  • Page 60

    60 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 175 adf stamp solenoid when the adf pcb cn25-2 signal level changes to 0v from +24v, solenoid operates for 1 second. F4 mode (check output) no. Item function remark.

  • Page 61

    61 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.1.4. F5 mode: function parameters (for copier) set the machine to service mode and press "5" key on the keypad. ↓ press the "start" key. ↓ enter the desired code number or press “v”, ”/\” arrow keys. ↓ if you wish to select another code number, scroll...

  • Page 62

    62 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 15 paper size (tray 2) (uf-7000/8000) 4 : a4-r 12 : legal 14 : letter-r 14 (for usa / canada) 4 (for europe / others) paper size (tray 2) (uf-7100/8100) 4 : a4-r 6 : b5-r 12 : legal 14 : letter-r 16-37 not used 38 duplex mode default 0 : no 1 : 1 to 2 2...

  • Page 63

    63 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 70 pm cycle 0 : no 1 : 1.5 k 2 : 2.5 k 3 : 5 k 4 : 10 k 5 : 15 k 6 : 20 k 7 : 30 k 8 : 40 k 9 : 60 k 10 : 85 k 11 : 90 k 12 : 120 k 13 : 150 k 14 : 200 k 15 : 240 k 0 (for usa / canada) 10 (for europe / others) 71-78 not used 79 image process method 0 :...

  • Page 64

    64 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 89 lan speed/duplex 0 : auto 1 : 10 half 2 : 10 full 3 : 100 half 4 : 100 full 0 90 beep sound 0 : off 1 : soft 2 : loud 1 91-94 not used 95 paper size (fa) (factory use only) 0 : japan 1 : usa/can 2 : europe 3 : other 1 (for usa / canada) 2 (for europe...

  • Page 65

    65 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.1.5. F6 mode: adjust parameters (for copier) set the machine to service mode and press "6" key on the keypad. ↓ press the "start" key. ↓ enter the desired code number or press “v”, ”/\” arrow keys. ↓ if you wish to select another code number, scroll t...

  • Page 66

    66 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 41-43 not used 44 fax laser duty adj. Printer density adjustment for fax. (-) : darker. (+) : lighter. -99 - +99 45 not used 46 prt laser duty adj. Printer density adjustment for printer. (-) : darker. (+) : lighter. -99 - +99 47-48 not used 49 text ima...

  • Page 67

    67 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.1.6. F7 mode: electronic counter set the machine to service mode and press "7" key on the keypad. ↓ press the "start" key. ↓ enter the desired code number or press “v”, ”/\” arrow keys. ↓ if you wish to select another code number, scroll the menu with...

  • Page 68

    68 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.1.7. F8 mode: service adjustment set the machine to service mode and press "8" key on the keypad. ↓ press the "start" key. ↓ enter the desired code number or press “v”, ”/\” arrow keys. ↓ if you wish to select another code number, scroll the menu with...

  • Page 69

    69 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.1.8. F9 mode: unit maintenance set the machine to service mode and press "9" key on the keypad. ↓ press the "start" key. ↓ enter the desired code number or press “v”, ”/\” arrow keys. ↓ if you wish to select another code number, scroll the menu with t...

  • Page 70

    70 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 f9 unit maintenance 06 ram initialize 00 parameter initialize resets the fax and function parameters to default values. 01 all job clear clears all jobs stored in flash memory. 02 lbp error log clear clears lbp error log 03 shipment set clears all jobs,...

  • Page 71

    71 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2. Service modes (for facsimile) caution: the factory default parameters are preset (country dependent) for optimum performance and in compliance with the local telecommunication regulations/standards, and do not need to be changed. Changing some of t...

  • Page 72

    72 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.3. Fax service mode 1 (function parameter setting) use the following procedure to change the function parameters. Enter the desired code number and press “start” key. ↓ if you wish to select another code number, scroll the menu with the “v”, ”/\” ar...

  • Page 73

    73 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 005 destination code (uf-7100/8100 only) 000 : austria 001 : u.K. 002 : canada 003 : denmark 004 : taiwan 005 : finland 006 : germany 007 : netherlands 008 : italy 009 : spanish 010 : hong kong 011 : australia 012 : switzerland 013 : norway 015 : portug...

  • Page 74

    74 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 011 rx level 1 = -43 dbm 2 = -38 dbm 3 = -33 dbm 4 = -48 dbm selects the receiving sensitivity of -33/-38/-43/-48 dbm. 012 dtmf level 00 = 0 dbm ~ 15 = -15 dbm selects the dtmf output level, 0 to -15 dbm in 1 dbm steps. 013 g3 rx eql 1 = 0db 2 = 4db 3 =...

  • Page 75

    75 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 025 comm. Start-up 1 = first 2 = second selects the communication start-up condition (xmt and polling). (used when echo suppression is disabled.) 026 non-standard 1 = off (invalid) 2 = on (valid) selects own mode (panafax mode). 027 short protocol b 1 =...

  • Page 76

    76 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 044 redial count 0 = no redial ~ 15 = 15 times 0 ~ 9 (for australia only) selects the redial count from 0 to 15 times in 1 step intervals. Note: in order to comply with the tbr21 requirement for the ec destinations, do not select 15 times. 045 ring dete...

  • Page 77

    77 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 068 nyse fax forward (usa and canada only) 1 = off 2 = on selects whether the machine will forward the incoming and outgoing faxes to a specified station. Note: once this parameter is activated, fax forwarding via fax parameter 054 is automatically disa...

  • Page 78

    78 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 082 jam length 1 = 1 m 2 = 2 m selects the maximum length of the original that can be scanned. 083 not used 084 line as no paper 1 = ring (ring) 2 = busy (keep line busy) selects whether to ring or send a busy tone to the remote station when the recordi...

  • Page 79

    79 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 note 1: continuous polling (station mode) this feature allows you to store or add documents into a polled file in memory. To enable the continuous polling feature set the function parameter no. 003 to "2:stn" (station). Depending on the setting of the u...

  • Page 80

    80 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 note 4: the default setting of parameters depends on the country’s specifications or regulations. Print the function parameter list to confirm the default settings. Note 5: 200 series function parameters only appear when the g3 communications port kit i...

  • Page 81

    81 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.4. Fax service mode 3 (printout of lists, reports and test results) from this service mode you can print the function parameter list, page memory test, printer report, all document file, protocol trace and the toner order form. 4.2.4.1. Function par...

  • Page 82

    82 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 note: 1. The contents of the function parameter list may vary depending on the country’s regulations. 2. “ * ” mark will be shown on the left side of number when setting was changed from default. Function parameter list (sample) ************* -function ...

  • Page 83

    83 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 note: 1. The contents of the function parameter list may vary depending on the country’s regulations. 2. “ * ” mark will be shown on the left side of number when setting was changed from default. Function parameter list (sample) ************* -function ...

  • Page 84

    84 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.4.2. Page memory test a test pattern prints out for checking the page memory and printer mechanism using the following procedure. Press the “v”, ”/\” arrow keys to select the "3: print report/list" on the display. ↓ press the “set” key to select the...

  • Page 85

    85 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.4.3. Printer report all printer errors are logged on the printer report which can be printed by the following procedure. Press the “v”, ”/\” arrow keys to select the "3: print report/list" on the display. ↓ press the “set” key to select the "1: func...

  • Page 86

    86 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.4.4. All document files print the document files from the flash memory. Press the “v”, ”/\” arrow keys to select the "3: print report/list" on the display. ↓ press the “set” key to select the "1: function parameter list". ↓ press the “v”, ”/\” arrow...

  • Page 87

    87 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.4.5. Protocol trace print a protocol trace report for the previous communication. Press the “v”, ”/\” arrow keys to select the "3: print report/list" on the display. ↓ press the “set” key to select the "1: function parameter list". ↓ press the “v”, ...

  • Page 88

    88 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.4.6. Toner order form the toner order form can be printed out manually by the following procedure. Press the “v”, ”/\” arrow keys to select the "3: print report/list" on the display. ↓ press the “set” key to select the "1: function parameter list". ...

  • Page 89

    89 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 explanation of contents (1) low toner message (fixed) “the toner supply in your machine is running low” (2) dealer name up to 25 digits (3) toner order tel # up to 36 digits (4) toner order fax # up to 36 digits (5) customer id up to 16 characters (user...

  • Page 90

    90 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.5. Fax service mode 4 (modem test) 4.2.5.1. Binary signal this service mode is used to check the binary signal output. Signals can be output to the line using the following procedure. Press the “v”, ”/\” arrow keys to select the "4: modem test" on t...

  • Page 91

    91 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.5.2. Tonal signal this service mode is used to check the tonal signal output. Signals can be output to the line using the following procedure. Press the “v”, ”/\” arrow keys to select the "4: modem test" on the display. ↓ press the “set” key. ↓ pres...

  • Page 92

    92 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.5.3. Dtmf signal this service mode is used to check the dtmf (dual tone multi frequency) signal output. The dtmf signal can be generated using the following procedure. • dtmf single tone press the “v”, ”/\” arrow keys to select the "4: modem test" o...

  • Page 93

    93 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.5.4. Binary signal (v.34) this service mode is used to check the binary signal output. Signals can be output to the line using the following procedure. (v.34) press the “v”, ”/\” arrow keys to select the "4: modem test" on the display. ↓ press the “...

  • Page 94

    94 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.6. Fax service mode 6 (ram initialization) initializes ram and restores the function parameters to their default values. Note: this operation should be performed when the unit is first installed. Press the “v”, ”/\” arrow keys to select the "6: ram ...

  • Page 95

    95 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.7. Fax service mode 8 (check & call) 4.2.7.1. Overview this feature enables the authorized servicing dealers to manage and improve the machine maintenance to their customers by alerting them of equipment problems. It also can be used as a supply sal...

  • Page 96

    96 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 note: tx (transmission) report: s = service alert report, m = maintenance alert report error code log tx report remarks ex-xx o s refer to the mechanical error code (e code) table. (sect. 3.1.3.) e13 o out of toner. Jxx o refer to the jam error code (j ...

  • Page 97

    97 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.7.3. Service alert report format explanation of contents (1) customer id (2) firmware version (3) counter information (4) print error last 30 records (latest on top) *************************************************** date mmm-dd-yyyy ***** time 03:...

  • Page 98

    98 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.7.4. Maintenance alert report format explanation of contents (1) low toner message (fixed) “machine is running out of toner” (2) customer id up to 16 characters (user identification code) (3) firmware version (4) transmission / reception / copy / pr...

  • Page 99

    99 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.7.5. Call counter report explanation of contents (1) customer id (2) firmware version (3) counter information (4) call counter pre-set value *************************************************** date mmm-dd-yyyy ***** time 03:47 ******** *************...

  • Page 100

    100 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 4.2.8. Service mode 9 (system maintenance) 4.2.8.1. Overview this service mode is used to maintain the machine. Use the following procedure for system maintenance. Press the “v”, ”/\” arrow keys to select the "9: system maintenance" on the display. ↓ p...

  • Page 101

    101 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5 exploded view & parts list note: 1. Panasonic document imaging company and other panasonic sales companies reserve the right to change any information enclosed herein without prior notification. (this includes, but is not limited to, parts pricing, a...

  • Page 102

    102 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.2. Control panel unit (for usa and canada) safety mark ref. No. Parts number part name new parts supplier remarks destination 101 pjgpc0001z cover, panel n for uf-8000 au pjgpc0008z for uf-7000 102 pjkec0007z base, panel n all 103 pjgac0001z window, ...

  • Page 103

    103 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 1 control panel unit (for usa and canada) 118 2104 109 108 115 x8 122 110 s6 123 111 113 112 116 114 117 121 120 2105 119 x8 x8 107 105 102 104 101 103 106 2102 x8 x8 2106.

  • Page 104

    104 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.3. Control panel unit (for other destinations) safety mark ref. No. Parts number part name new parts supplier remarks destination 201 pjgpc0010z cover, panel n for uf-7100 al, am, eb pjgpc0002z for uf-8100 pjgpc0033z for uf-7100 ae pjgpc0031z for uf-...

  • Page 105

    105 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 2 control panel unit (for other destinations) 2104 109 108 113 x8 122 110 s6 123 112 111 114 117 116 115 2105 x8 x8 118 105 102 104 201 202 203 103 106 107 2102 x8 x8 2106.

  • Page 106

    106 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.4. Adf safety mark ref. No. Parts number part name new parts supplier remarks destination 301 pjkcc0001z cover, adf n all 302 pjukc0008z guide, upper paper n all 303 pjhgc0021z sponge n all 304 pjbac0004z lever, paper sensor n all 305 pjhrc0007z guid...

  • Page 107

    107 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 3 adf (1/3) 308 309 310 307 305 306 333 313 x8 x8 y14 332 310 338 301 337 316 316 y14 y3 330 315 314 y3 303 304 302 317 320 s6 329 328 h7 327 331 325 326 326 h7 327 335 334 324 y16 y15 x8 323 321 y14 311 see fig. 4 y1...

  • Page 108

    108 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 331 ffpfa01561 screw, shoulder n all 332 pjscc0007z brush, antistatic n all 333 pjbuc0067z plate, spring ground n all 334 stw6x1 poly slider c all 335 pjbvc0012z spring,...

  • Page 109

    109 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 3 adf (1/3) 308 309 310 307 305 306 333 313 x8 x8 y14 332 310 338 301 337 316 316 y14 y3 330 315 314 y3 303 304 302 317 320 s6 329 328 h7 327 331 325 326 326 h7 327 335 334 324 y16 y15 x8 323 321 y14 311 see fig. 4 y1...

  • Page 110

    110 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 401 pjhec0018z pad, adf n pm all 402 pjukc0010z cover, separation roller n all 403 pjdrc0007z roller, separation n pm all 404 pjugc0008z shaft, separation fulcrum n all ...

  • Page 111

    111 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 445 h6 439 411 413 401 402 h6 403 442 448 406 407 406 405 404 h7 y3 419 h6 457 h7 411 441 408 461 443 443 y3 427 426 424 425 423 422 h6 421 429 429 430 449 428 449 440 456 y3 437 460 458 451 h7 459 y14 433 449 432 j8 j8 424 449 449 428 449 431 428 452 ...

  • Page 112

    112 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 450 pjbuc0064z spring, front pressure n all 451 pjbuc0065z spring, rear pressure n all 452 pjukc0076z guide, paper n all 453 dzhp000237 unit, stamp c au dzhp000240 excep...

  • Page 113

    113 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 445 h6 439 411 413 401 402 h6 403 442 448 406 407 406 405 404 h7 y3 419 h6 457 h7 411 441 408 461 443 443 y3 427 426 424 425 423 422 h6 421 429 429 430 449 428 449 440 456 y3 437 460 458 451 h7 459 y14 433 449 432 j8 j8 424 449 449 428 449 431 428 452 ...

  • Page 114

    114 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 501 pjuec0011z stay 2 n all 502 pjukc0013z guide, paper exit n all 503 pjdrc0062z roller, reverse exit n all 504 pjdyc0005z shaft, reverse exit roller n all 505 pjbvc001...

  • Page 115

    115 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 5 adf (3/3) 443 336 336 443 320 509 320 501 y3 y3 537 502 443 504 503 505 y3 505 510 h7 422 421 512 534 528 535 334 y16 527 511 y16 531 524 y14 515 526 336 526 539 526 336 443 508 507 506 519 516 y3 537 h7 520 533 536...

  • Page 116

    116 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 320 dzal000072 sensor, photo c all 334 stw6x1 poly slider c all 336 uams-05-2 clamp c all 421 pjdgc0005z gear, paper feed n all 422 pjdec0005z roller, pitch n all 443 ed...

  • Page 117

    117 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 5 adf (3/3) 443 336 336 443 320 509 320 501 y3 y3 537 502 443 504 503 505 y3 505 510 h7 422 421 512 534 528 535 334 y16 527 511 y16 531 524 y14 515 526 336 526 539 526 336 443 508 507 506 519 516 y3 537 h7 520 533 536...

  • Page 118

    118 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.5. Cover assembly safety mark ref. No. Parts number part name new parts supplier remarks destination 601 pjkmc0005z cover, inner top n all 602 pjkmc0008z cover, inner left n all 603 pjkmc0009z cover, inner rear n all 605 pjkmc0007z cover, inner right...

  • Page 119

    119 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 6 cover assembly 628 19 2027 626 629 627 620 t8 t8 618 619 t8 620 615 t9 t9 624 622 625 623 623 624 621 632 t9 620 633 620 634 644 624 635 641 601 y13 602 612 605 643 636 640 606 630 603 607 y14 609 s6 v6 637 610 611 ...

  • Page 120

    120 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 640 pjqtb0006z label, hot surface caution n all 641 pjuec0130z stopper, tray n all 642 pjqhc0060z label, g3 line n for uf-8000/ 8100 all 643 pjkzc0034z assembly, tray co...

  • Page 121

    121 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 6 cover assembly 628 19 2027 626 629 627 620 t8 t8 618 619 t8 620 615 t9 t9 624 622 625 623 623 624 621 632 t9 620 633 620 634 644 624 635 641 601 y13 602 612 605 643 636 640 606 630 603 607 y14 609 s6 v6 637 610 611 ...

  • Page 122

    122 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.6. Right side parts safety mark ref. No. Parts number part name new parts supplier remarks destination 701 pjuac0013z bracket, adf tray n all 702 pjmcc0005z plate, interface n all 704 pjmcc0008z case, g3 option n for uf-8000/ 8100 all 705 pjmcc0004z ...

  • Page 123

    123 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 7 right side parts (1/2) 709 t9 713 2002 u1 2032 715 715 2026 2029 u1 701 y3 y3 702 704 2003 714 y3 y3 y3 705 y3 2005 y3 706 2001 711 711 y3 710 y3 709 y3 712 707 708 716 y3 y3 717.

  • Page 124

    124 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 801 pjdgb0052z gear, adu drive c oapd all 802 pjdgb0070z gear, registration drive c oapd all 803 pjdgb0072z gear, idle z19 c oapd all 804 pjdgb0071z gear, double teeth c...

  • Page 125

    125 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 8 right side parts (2/2) t9 811 812 814 813 t9 823 u1 801 449 802 811 803 805 2028 t9 811 804 808 807 806 811 809 t9 u1 817 713 713 t9 837 fig. 9 u1 826 u1 816 u1 t9 3f 821 822 815 816 u1 824 816 u1 713 829 831 833 y3...

  • Page 126

    126 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.7. Motor and drive gear unit safety mark ref. No. Parts number part name new parts supplier remarks destination 901 pjdgb0047z gear, opc b c oapd all 902 pjdgb0048z gear, opc a c oapd all 903 pjdgb0049z gear, fuser c oapd all 904 pjdgb0056z gear, reg...

  • Page 127

    127 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 9 motor and drive gear unit 909 907 811 902 811 905 901 903 906 904 908 u1 u1.

  • Page 128

    128 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.8. Left side parts safety mark ref. No. Parts number part name new parts supplier remarks destination 1001 pjdsb0033z spring, grid c oapd all 1002 pjdsb0148z spring, charge c oapd all 1003 pjdsb0009y spring, opc c oapd all 1004 pjdsb0149z spring, dev...

  • Page 129

    129 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 10 left side parts (1/2) 1001 1005 1004 1002 1003 t9 u3 1007 1006 1019 p3 y12 624 1009 624 634 1010 1010 1022 1013 1012 y3 y3 716 1011 y3 y3 1014 1028 1028 1013 y3 1031 1018 1016 y3 y17 y3 2101 1024 1021 1027 1028 716...

  • Page 130

    130 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 1101 pjuac0008z bracket, left side n all 1102 pjmec0044z holder, harness n all 1103 pjmcc0007z plate, joint n all 1104 pjmcc0010z bracket, ground (earth) n all 1105 pjws...

  • Page 131

    131 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 11 left side parts (2/2) 835 1106 1105 1105 1107 y3 1102 y14 y14 1101 1103 y3 y3 1104 2004 y3 y9.

  • Page 132

    132 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.9. Rear and upper parts safety mark ref. No. Parts number part name new parts supplier remarks destination 1201 pjzbp7305m assembly, upper exit roller holder c oapd all 1202 pjdgb0024z gear, z21 fuser c oapd all 1203 pjdgb0026z gear, z36 upper exit r...

  • Page 133

    133 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 12 rear and upper parts w7 1214 1216 1212 w4 2030 1213 w4 1204 809 1202 1205 806 1203 1203 1204 809 t9 1206 1210 1207 u9 t9 1209 1211 1208 u4 1201 u1 fig. 13.

  • Page 134

    134 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.10. Fuser unit safety mark ref. No. Parts number part name new parts supplier remarks destination 1301 pjdfb0122z shaft, fuser drive c oapd all 1302 pjdgb0023z gear, z24 fuser c oapd all 1303 pjmdb0018z plate, lead wire c oapd all 1304 l2aa00000090 t...

  • Page 135

    135 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 13 fuser unit 1328 1317 1313 1320 1312 1327 1308 1307 1314 1315 1315 1306 1316 1314 1317 624 g8 v1 v1 1309 1305 1202 1206 1321 1302 1301 t9 1326 t9 u5 u4 t9 t9 1318 1324 1325 1323 t9 1322 1319 1303 t9 1329 t9 t9 u3 u3...

  • Page 136

    136 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination t9 xtw3+8s screw c oapd all u3 xyc3+ff8c screw c oapd all u4 xtw3+12s screw c oapd all u5 xtw3+12sfz screw c oapd all v1 xyc3+ff6 screw c oapd all.

  • Page 137

    137 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 13 fuser unit 1328 1317 1313 1320 1312 1327 1308 1307 1314 1315 1315 1306 1316 1314 1317 624 g8 v1 v1 1309 1305 1202 1206 1321 1302 1301 t9 1326 t9 u5 u4 t9 t9 1318 1324 1325 1323 t9 1322 1319 1303 t9 1329 t9 t9 u3 u3...

  • Page 138

    138 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.11. Pick up roller and paper feed roller safety mark ref. No. Parts number part name new parts supplier remarks destination 1401 pjdgb0040z gear, pick up internal c oapd all 1402 pjdgb0041z gear, pick up arm c oapd all 1403 pjdrb0021z roller, registr...

  • Page 139

    139 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 14 pickup roller and paper feed roller 1406 1404 1406 1407 1408 1419 1411 1406 1205 1402 809 809 1401 815 1420 1022 u8 1406 449 1413 1416 1415 1412 1403 1405 1418 1409 1409 1417 625 1414.

  • Page 140

    140 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.12. Bottom parts safety mark ref. No. Parts number part name new parts supplier remarks destination 1501 pjuab0024y plate, lower base c oapd all 1502 pjmdb0020z plate, adu pinch roller c oapd all 1503 pjdrb0018z roller, adu pinch c oapd all 1504 pjdf...

  • Page 141

    141 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 15 bottom parts 2031 t9 1516 1515 1517 1514 1509 1406 u6 1510 1511 1508 1501 t9 p3 1503 1505 1505 u1 u1 1504 1506 1502 1506 1513 1512 u7 u7 1512 t9 1518 t9.

  • Page 142

    142 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.13. Mechanical base safety mark ref. No. Parts number part name new parts supplier remarks destination 1601 pjhrb0324z holder, transfer roller c oapd all 1602 pjdsb0040z spring, transfer c oapd all 1603 pjdrb0081z roller, bias transfer c oapd pm all ...

  • Page 143

    143 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 16 mechanical base 1607 u8 1615 1613 1608 u8 1615 1614 1618 1603 811 1604 811 1604 1605 811 1601 1601 1602 1602 1606 t9 1609 v1 t9 1611 u8 1610 u1 1616 t9 t9 815 1612 u1 p3 713 1617 1619 1620 y3 1621 1622 y3.

  • Page 144

    144 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.14. Paper tray safety mark ref. No. Parts number part name new parts supplier remarks destination 1701 pjmdb0026y lifter, paper c oapd all 1702 pjhsb0007z pad, friction c oapd all 1703 pjdsb0179z spring, retard pad c oapd all 1704 pjhrb0031z guide, r...

  • Page 145

    145 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 17 paper tray 1706 1702 u8 u8 u8 1713 1714 1714 1710 1711 1704 1712 u8 1705 1722 1701 1715 1708 1707 1703 1716 1706 1709 1717 1718 1721 1720 1719.

  • Page 146

    146 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.15. 2nd paper feed module safety mark ref. No. Parts number part name new parts supplier remarks destination 1801 pjkeb0019z cover, front c oapd all 1802 pjkeb0097z cover, right c all 1803 pjkeb0098z cover, left c all 1804 pjusb0027z plate, pinch rol...

  • Page 147

    147 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 18 2nd paper feed module u1 u1 u1 1828 1826 u1 1808 u1 1810 u1 u1 1828 1831 1837 v6 1811 1833 1836 1825 1515 u1 1807 1827 1827 1809 1801 u1 1832 u1 u1 u1 1802 1803 1804 1805 v2 t9 1816 1510 1817 1406 449 1815 811 1823...

  • Page 148

    148 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 2103 pjwppmf3m2 pc board, 2nd feeder c oapd rtl, pbf all t9 xtw3+8s screw c oapd all u1 xtw3+6l screw c all v2 xtw3+6s screw c all v3 xwe4 washer c all v6 xtb3+8jfn scre...

  • Page 149

    149 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 18 2nd paper feed module u1 u1 u1 1828 1826 u1 1808 u1 1810 u1 u1 1828 1831 1837 v6 1811 1833 1836 1825 1515 u1 1807 1827 1827 1809 1801 u1 1832 u1 u1 u1 1802 1803 1804 1805 v2 t9 1816 1510 1817 1406 449 1815 811 1823...

  • Page 150

    150 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.16. Paper tray (2nd paper feed module) safety mark ref. No. Parts number part name new parts supplier remarks destination 1901 pjhrb0338z base, paper tray c oapd all 1902 pjhrb0340z guide, right paper side c oapd all 1903 pjhrb0341z guide, left paper...

  • Page 151

    151 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 19 paper tray (2nd paper feed module) 1702 1917 1909 1910 1910 1708 1707 1919 1907 1906 1907 1903 1918 1905 1912 1911 1904 1913 1915 1714 1714 1713 u8 u8 1911 1902 1908 1901 1916 1914.

  • Page 152

    152 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.17. Pc boards safety mark ref. No. Parts number part name new parts supplier remarks destination 2001 pjwpf2688au pc board, sc n for uf-7000 au pjwpf2687au for uf-8000 pjwpf2688ae for uf-7100 ae pjwpf2687ae for uf-8100 pjwpf2688ag for uf-7100 ag pjwp...

  • Page 153

    153 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 20 pc boards / harnesses (1/2) engine control (2002) 2013 2017 2018 2019 2020 1212 2021 822 2022 1006 1420 2023 2024 2025 2014 2015 1213 2016 cn002 cn003 cn005 cn001 cn006 cn010 cn004 cn008 cn017 cn016 cn015 cn014 cn0...

  • Page 154

    154 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 2021 pjjec10003y harness, hvps (flat harness) c oapd all 2022 pjjrml0020z harness, motor c oapd all 2023 pjjrb1026z harness, exit solenoid relay c all 2024 pjjrb1028z ha...

  • Page 155

    155 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 20 pc boards / harnesses (1/2) engine control (2002) 2013 2017 2018 2019 2020 1212 2021 822 2022 1006 1420 2023 2024 2025 2014 2015 1213 2016 cn002 cn003 cn005 cn001 cn006 cn010 cn004 cn008 cn017 cn016 cn015 cn014 cn0...

  • Page 156

    156 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 2101 pjwpf2684au pc board, sdr n all 2102 pjwpf2680ae pc board, pnl 1 n all 2103 pjwppmf3m2 pc board, 2nd feeder c oapd all 2104 pjwpf2682au pc board, pnl 3 n all 2105 p...

  • Page 157

    157 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 21 pc boards / harnesses (2/2) 2112 1834 1835 2nd feeder (2103) cn602 cn600 cn601 440 1907 2107 2111 2012 2110 2108 2007 2007 2109 454 2006 123 2115 2114 2113 2114 2106 2115 2113 sdr (2101) pnl1 (2102) pnl3 (2104) pnl...

  • Page 158

    158 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.18. Packing and accessories safety mark ref. No. Parts number part name new parts supplier remarks destination 2201 pjpec0003z pad, top n all 2202 pjpgc0032z box, carton n for uf-7000 au pjpgc0002z for uf-8000 au pjpgc0132z for uf-7100 yv pjpgc0131z ...

  • Page 159

    159 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 22 packing and accessories 2201 2202 2203 2203 2204 608 2219 2208 2209 2206 2207 2205 2217 2210 2220 2221 2211 2212 338 337 2213 2214 2223 2216, 2218 2215 202.

  • Page 160

    160 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 safety mark ref. No. Parts number part name new parts supplier remarks destination 2215 pjqtc0005z holder, directory sheet n au 2216 pjqqc0012z quick guide n au pjqqc0013z ag, al, av, eb 2217 pjpcc0001z box, accessories n all 2218 pjqmc0081z operating ...

  • Page 161

    161 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 22 packing and accessories 2201 2202 2203 2203 2204 608 2219 2208 2209 2206 2207 2205 2217 2210 2220 2221 2211 2212 338 337 2213 2214 2223 2216, 2218 2215 202.

  • Page 162

    162 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.19. 2nd paper feed module packing and accessories safety mark ref. No. Parts number part name new parts supplier remarks destination 2301 pjpgb0230z carton box c au, yv pjpgb0230y except au, yv 2302 pjpnb0154z cushion, front c all 2303 pjpnb0155z cus...

  • Page 163

    163 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 23 2nd paper feed module packing and accessories 2303 2306 2305 v6 1838, 1839 2304 2302 2301 u1 1836 1837.

  • Page 164

    164 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.20. Printer controller module for pcl6 safety mark ref. No. Parts number part name new parts supplier remarks destination 2401 pjqrc0027z installation instructions n all 2402 pjwacc00014z software cd n au pjwacc00015z except au 2403 dzrb000101 carton...

  • Page 165

    165 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 24 printer controller module for pcl6 2403 2402 2032 2401.

  • Page 166

    166 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.21. G3 communication port kit (for uf-8000/8100) safety mark ref. No. Parts number part name new parts supplier remarks destination 2501 pjqrc0029z installation instructions n all 642 pjqhc0060z label, g3 line n all 704 pjmcc0008z case, g3 option n a...

  • Page 167

    167 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 25 g3 communication port kit 2501 2403 2003 704 714 705 2211 2009 642 y3 2220

  • Page 168

    168 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.22. Network scan / email / internet fax kit safety mark ref. No. Parts number part name new parts supplier remarks destination 2601 pjqrc0028z installation instructions n all 2602 pjqqc0017z quick guide n au pjqqc0018z except au, ae, er, yc, yv pjqqc...

  • Page 169

    169 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 a c d e b 8 1 3 4 5 6 7 2 2 2 fig. 26 network scan / email / internet fax kit 2403 2032 2601 2603 2602.

  • Page 170

    170 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 5.23. Hardware identification template part no. Figure remark ref. No. Screw xyn3+f5 3f screw xtw3+8l p3 screw xtw3+8s t9 screw xtw3+6l u1 screw xyc3+ff8c u3 screw xtw3+12s u4 screw xtw3+12sfz u5 screw pjneb0003y u7 screw dzpa000086 s6 snap ring ffpfj0...

  • Page 171

    171 nov 2004 ver. 2.0 uf-7000/7100 uf-8000/8100 screw xtb2+12j w4 screw xtb3+8gfj x8 screw xtw3+8lfj y13 screw xtw3+8sfj y14 screw xyn4+f8fj y9 screw xyn3+f6fj y16 screw xtb26+6jfj y17 screw xtw3+6lfj y3 washer xwg3fu y12 washer xwe4 v3 screw y15 xtb4+8ffj screw pjnac0003z w7 part no. Figure remark ...

  • Page 172: 6 Alphanumerical Parts List

    172 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 6 alphanumerical parts list alphanumerical parts list part number part name ref. No. Supplier pm destination 40s2m120 belt, paper transfer timing 527 all a4dp3l000003 lamp, halogen 1309 au, ae a4dp7k000002 except au, ae cr2032 battery 122 all dzal00007...

  • Page 173

    173 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 dzfn000120 converter, telephone line 2220 al, eb dzfp001554 harness, power supply 2016 all dzfp001555 cable, ecb (flat harness) 2025 all dzhp000237 unit, stamp 453 au dzhp000240 except au dzje000165 cradle, lower 628 yr, yx dzje000166 cradle, upper 627...

  • Page 174

    174 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 pjbcc0006z key, stop 105 all pjbcc0007z key, start 107 all pjbcc0008z key, serial 108 all pjbcc0009z key, copy 106 all pjbcc0010z key, set 112 all pjbcc0011z key, clear 113 all pjbcc0012z key, energy 116 all pjbcc0013z key, function 117 all pjbcc0014z ...

  • Page 175

    175 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 pjdgb0038z gear, registration roller 1404 oapd all pjdgb0039z gear, paper feed roller 1407 oapd all pjdgb0040z gear, pick up internal 1401 oapd all pjdgb0041z gear, pick up arm 1402 oapd all pjdgb0042z gear, registration internal 808 oapd all pjdgb0043...

  • Page 176

    176 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 pjdrb0018z roller, adu pinch 1503 oapd all pjdrb0021z roller, registration 1403 oapd all pjdrb0022z roller, paper feed 1405 oapd all pjdrb0025z roller, paper feed 1816 oapd all pjdrb0059z roller, sub 1009 oapd all pjdrb0081z roller, bias transfer 1603 ...

  • Page 177

    177 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 pjgac0001z window, lcd 103 au, eb, other pjgac0002z av pjgac0003z ag pjgac0004z yv pjgac0005z ae pjgec0001z sheet, white base (for uf-7100/8100) 203 except au pjgec0002z sheet, paper tray a (for uf-7000/8000) 1717 au pjgec0003z sheet, paper tray b (for...

  • Page 178

    178 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 pjhec0046z film, fxb 834 all pjhec0047z sheet, fxb 2 836 all pjhec0051z film, sc 712 all pjhec0055z film, sdr 1 1025 all pjhec0060z film, drive gear bracket 837 all pjhg351z plate, rubber 1827 oapd all pjhgc0004z rubber, separation pad 1919 all pjhgc00...

  • Page 179

    179 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 pjhrc0026z holder, pcb 118 all pjhrc0035z sheet, white 536 all pjhrc0036z support, right paper 617 all pjhrc0037z support, left paper 616 all pjhrc0055z sheet, paper chute 1840 all pjhrc0154z sheet, clutch guide 1842 all pjhrc0176z plate, spacer 1841 a...

  • Page 180

    180 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 pjkmc0002z cover, rear 2 607 all pjkmc0003z cover, right 613 all pjkmc0004z cover, left 612 all pjkmc0005z cover, inner top 601 all pjkmc0006z cover, sd memory card 610 all pjkmc0007z cover, inner right 605 all pjkmc0008z cover, inner left 602 all pjkm...

  • Page 181

    181 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 pjnw620z washer 906 oapd all pjnw721z poly slider 1208 oapd all pjnw820z washer, plastic 1417 oapd all pjpcc0001z box, accessories 2217 all pjpec0003z pad, top 2201 all pjpec0016z pad, bottom 2208 all pjpgb0230y carton box 2301 except au, yv pjpgb0230z...

  • Page 182

    182 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 pjuac0008z bracket, left side 1101 all pjuac0009z supporter, side 708 all pjuac0010z supporter, front left side 1014 all pjuac0011z bracket, front adf 1013 all pjuac0012z bracket, rear adf 833 all pjuac0013z bracket, adf tray 701 all pjuac0065z frame, ...

  • Page 183

    183 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 pjusb0025z spring, ground 816 oapd all pjusb0027z plate, pinch roller 1804 oapd all pjusb0080z spring, ground 1811 oapd all pjusb0089z spring, side guide 1908 oapd all pjwacc00004z software cd 2212 au pjwacc00008z except au pjwacc00014z software cd 240...

  • Page 184

    184 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 pjws00gw0mq assembly, inlet 1105 au, ae pjws00gw1mq except au, ae pjws2p7100m switch, opc drum unit interlock 1213 oapd all pjwsp7105m switch, front door safety interlock 1212 oapd all pjwuf2680au cis (for uf-8000/8100) 440 all pjwuf2681au cis (for uf-...

  • Page 185

    185 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 xtw26+8s screw t8 oapd all xtw3+12s screw u4 oapd all xtw3+12sfz screw u5 oapd all xtw3+6l screw u1 all xtw3+6lfj screw y3 all xtw3+6s screw v2 all xtw3+8l screw p3 all xtw3+8lfj screw y13 all xtw3+8s screw t9 oapd all xtw3+8sfj screw y14 all xtw3+u8s ...

  • Page 186

    186 uf-7000/8000 nov 2004 ver. 2.0 uf-7100/8100 memo.

  • Page 187

    187 e.