1. DL manuals
  2. PlaySafe
  3. Toy
  4. 22-PS302
  5. Owner's Manual

PlaySafe 22-PS302 Owner's Manual

Manual is about: Manchester II Deluxe 6-Leg Swing Set

Summary of 22-PS302

  • Page 1

    1 ©2006 pacific cycle, inc. Owner’s manual and assembly instruction model #: 22-ps302 model name: manchester ii deluxe 6-leg swing set manual date: september, 2007 important: keep this owner’s manual; do not discard in case you need to contact pacific cycle, inc. In the future. Should there be a cha...

  • Page 2

    2 ©2006 pacific cycle, inc. Playsafe™ customer service pacific cycle, inc 4730 east radio tower lane olney, il 62450 or by email: info@playsafeoutdoors.Com warnings and safety information o bserve all warnings and statements in order to reduce the risk of injury or death . • before you assemble the ...

  • Page 3

    3 ©2006 pacific cycle, inc. • v erify that all swings and chains are secured at both ends . • never attach any materials that are not specifically designed for use with this swing set , such as jump ropes , pet leashes , rope or cords and other chains as these pose a potential strangulation hazard ....

  • Page 4

    4 ©2006 pacific cycle, inc. Fall height in feet from which a life threatening injuly would not be expected material type 6 in. Depth 9 in. 12 in. Double shredded bark mulch 6’ 10’ 11’ wood chips 6’ 7’ 12’ fine sand 5’ 5’ 9’ fine gravel 6’ 7’ 10’ it is recommended that a shock absorbing material shou...

  • Page 5

    5 ©2006 pacific cycle, inc. Parts list for swing set remove all parts from the package and lay them out before you begin assembly. If any parts are missing, please call 1- 800-242-6110. Main frame name each top bar with hooks 2 corner leg fitting 2 center leg fitting 1 leg 6 support bar 3 swings and...

  • Page 6

    6 ©2006 pacific cycle, inc. Support bar x3 corner leg fitting x2 center leg fitting x1 pre-assembled parts: • swing and trapeze hooks should be in place on the top tube. • hardware for legs should be in place in the corner fittings. • hardware for support bars should be in place on the legs. • foam ...

  • Page 7

    7 ©2006 pacific cycle, inc. 6 remove the hardware from the middle section of a leg. Match up the holes of the mid-leg and support bar and re-insert the hardware through both. Repeat the process for the opposite side and center legs. It may be necessary to pull both legs towards each other in order f...

  • Page 8

    8 ©2006 pacific cycle, inc. Step illustration instructions hardware reference 1 secure the deluxe glider brackets with the v-screws and the bolts at the squared portions of the top bar. Part ref. #: pshw35, pshw22 2 remove the hardware from the arms of the brackets. Place the bracket bar between the...

  • Page 9

    9 ©2006 pacific cycle, inc. 4 remove the pre-inserted hardware from the end sections. Then connect the seat section to the end sections by lining up the holes and reinserting the hardware. 5 once fully assembled, hang the chains from the swing hooks attached to the bracket bars. Ensure that the glid...

  • Page 10

    10 ©2006 pacific cycle, inc. Lawn swing assembly required parts: lawn swing attachment x2, vertical pole x4, foot plate x2, u-shaped hand rail x4, seat support bar x8, seat/backrest x4 assembly drawing completed swing step illustration instructions hardware reference 1 secure the lawn swing attachme...

  • Page 11

    11 ©2006 pacific cycle, inc. 3 join the two footrest sections by twisting them together until the playsafe™ logo aligns. 4 insert the foot plate support bar through the footrest. 5 using an adjustable wrench, attach the vertical poles to the foot plate support bar. Repeat steps 5 and 6 for the other...

  • Page 12

    12 ©2006 pacific cycle, inc. 9 using the hardware provided on the u- shaped hand rails, attach the seat support bars and backrests. Note: this step is identical to step 8 for installing the seats. Part ref. # pshw17 10 after fully assembled, ensure the lawn swing swings freely. If it does not, make ...

  • Page 13

    13 ©2006 pacific cycle, inc. Step illustration instructions hardware reference 1 remove the hardware from the frame attachment and connect the extension. Re- insert the hardware and tighten. Note: be sure that the lower part of the see-saw extension is buried and anchored per the anchoring instructi...

  • Page 14

    14 ©2006 pacific cycle, inc. Slide assembly required parts: slide x1 rail/ladder leg x2 front leg x2 ladder step x2 link bar x2 proper placement: slide assembly correct location incorrect location pre-assembled parts: • the screws and bolts for the slide rail/ladder legs are inserted on the slide. T...

  • Page 15

    15 ©2006 pacific cycle, inc. 4 locate the slide front legs and insert them into the front hand rail tubes, on the underside of the slide. Align the holes and secure with the screws, washers and lock nuts. Part ref. #: pshw24 5 slide the two ladder steps onto the legs of the slide. Align the holes an...

  • Page 16

    16 ©2006 pacific cycle, inc. Important last steps! Tighten all hardware. Do not allow children to play on the swing set until it is fully assembled, all items are tightened, and the unit is properly anchored. • do not over tighten nuts and bolts. Once they are tight, turn them ½ rotation more to be ...