Summary of Bushranger Edger
Page 2
2 copyright © roy gripske & sons pty. Ltd. 2012 safety awareness whenever you see the symbols shown below, heed their instructions! Always follow safe operating and maintenance practices. Warning this warning symbol identifi es special instructions or procedures which, if not correctly followed, cou...
Page 3
3 copyright © roy gripske & sons pty. Ltd. 2012 safety tips operate safely: service safely: wear protective clothing avoid rotating blade avoid injury from thrown objects read this first read and understand all safety tips before using edger. Before you operate: remove all debris that might wrap aro...
Page 4
4 copyright © roy gripske & sons pty. Ltd. 2012 »»»»»»»»»»»»»»»»»specifications««««««««««««««««« engine type displacement bore x stroke maximum horsepower air cleaner ignition spark plug lubrication system engine oil capacity fuel tank capacity dimensions overall length overall width overall height ...
Page 5
5 copyright © roy gripske & sons pty. Ltd. 2012 operation starting engine • with clutch/blade control lever in disengaged position, move ignition switch to run. A. Ignition switch b. Engine/blade control lever speed control • put engine speed control in mid-throttle position. • pull choke rod to clo...
Page 6
6 copyright © roy gripske & sons pty. Ltd. 2012 adjusting cutting depth • move control lever over to the right to raise or lower cutting blade assembly. A. Control lever • when control lever is moved back to center position, pin locates in appropriate hole for required cutting depth. A. Pin adjustin...
Page 7
7 copyright © roy gripske & sons pty. Ltd. 2012 »»»»»»»»»»»»»»» maintenance and adjustment «««««««««««««« periodic maintenance chart to ensure satisfactory operation over an extended period of time, any engine requires normal maintenance at regular intervals. The periodic maintenance chart below sho...
Page 8
8 copyright © roy gripske & sons pty. Ltd. 2012 a a a a blade nut and engine mounting nuts • check blade nut for tightness. Blade nut torque is 39 n-m (4.0 kg-m). • check engine mounting nuts for tightness. Tightening torque is 18 n-m (1 .8kg-m). A. Blade nut a. Engine mounting nuts engine cooling f...
Page 9
9 copyright © roy gripske & sons pty. Ltd. 2012 b c maintenance and adjustment a blade blade is sharp and can cut you. Help avoid in- jury before you check blade: stop engine. Let engine cool. Wear gloves or wrap blade with rag. Check blade for damage. • remove blade: - lower edger until blade touch...
Page 10
10 copyright © roy gripske & sons pty. Ltd. 2012 drive belt a. Blade angle lever replacement • remove belt from blade sheave. • remove belt from engine sheave . • pull belt out from rear. A. Blade sheave b. Engine sheave • install new belt. Be sure angle lever is in the middle segmented position. • ...
Page 11
11 copyright © roy gripske & sons pty. Ltd. 2012 »»»»»»»»»»»»»»» troubleshooting «««««««««««««««« problem solution section engine does not start. Fill fuel tank. Pull choke rod to “choke” position. Connect spark plug wire. Check and set spark plug gap. Install new spark plug. Ignition parts bad. See...
Page 12
12 copyright © roy gripske & sons pty. Ltd. 2012 storage • make sure that the control rod is supported on the support plate between the two shoulders on the control rod a. Belt adjustment nuts storing edger gasoline is extremely fl ammable and can be explosive under certain conditions. Turn the igni...
Page 13
13 copyright © roy gripske & sons pty. Ltd. 2012 assembly • tighten blade nut: - lower edger until blade touches ground as shown. - hold opposite end of blade spindle with wrench. - tighten nut to 39 n-m (4.0kg-m). Add engine oil do not check or add oil when engine is running edger is shipped withou...
Page 14
14 copyright © roy gripske & sons pty. Ltd. 2012 maintenance schedule dealer:_________________________________________________________ serial number:___________________________________________________ engine number: _________________________________________________ hours maintenance performed parts ...
Page 15
15 copyright © roy gripske & sons pty. Ltd. 2012 hours maintenance performed parts replaced.
Page 16
Www.Poweruplawncare.Com.Au.