1. DL manuals
  2. Quantum
  3. Computer Accessories
  4. 3U
  5. Quick Start Manual

Quantum 3U Quick Start Manual

Manual is about: Rackmount Enclosure with LTO-5 Full-Height Tape Drive

Summary of 3U

  • Page 1

    Lto-5 full-height tape drive contents connecting the drive interface and power cables .....................................................2 installing a second tape drive or replacing a tape drive ...........................3 preinstallation requirements .............3 installation procedure .........

  • Page 2

    2 connecting the drive interface and power cables lto-5 full-height tape drive power requirements power requirements for the 3u rackmount enclosure are as follows: • 100 to 240 volts ac/2 to 4 amps • 47 to 63 hz connecting the drive interface and power cables 1 shut down and turn off the host server...

  • Page 3

    Installing a second tape drive or replacing a tape drive 3 lto-5 full-height tape drive 5 connect the other end of the ac power cable to the rack/facility ac power receptacle. 6 press the master ac power switch on the front of the 3u rackmount enclosure to apply power to the enclosure and illuminate...

  • Page 4

    4 installing a second tape drive or replacing a tape drive lto-5 full-height tape drive installation procedure the installation procedure is divided into the following major sections: note: the 3u rackmount enclosure is designed for full-height tape drives, however, half-height tape drives can also ...

  • Page 5

    Installing a second tape drive or replacing a tape drive 5 lto-5 full-height tape drive 2 loosen the thumbscrew. 3 remove the drive tray (see figure 5 ): a push the drive tray toward the rear of the 3u enclosure. B pull the drive tray up and out at an angle. Figure 5 removing the drive blank drive t...

  • Page 6

    6 installing a second tape drive or replacing a tape drive lto-5 full-height tape drive figure 6 installing the tape drive 8 secure the tape drive tray by tightening the thumbscrew. Continue with connecting the tape drive cables on page 8. Replacing a tape drive: to replace a tape drive: 1 remove th...

  • Page 7

    Installing a second tape drive or replacing a tape drive 7 lto-5 full-height tape drive figure 7 removing the tape drive 2 remove the screws securing the mounting drive tray to the tape drive. 3 remove the failed tape drive from the drive tray. 4 position the new tape drive in the drive tray and ali...

  • Page 8

    8 installing a second tape drive or replacing a tape drive lto-5 full-height tape drive figure 8 installing the new tape drive 7 secure the tape drive tray by tightening the thumbscrew. Continue with connecting the tape drive cables on page 8. Connecting the tape drive cables to connect the tape dri...

  • Page 9

    Installing a second tape drive or replacing a tape drive 9 lto-5 full-height tape drive closing the top panel to close the top panel (see figure 10 ): 1 close the top access panel. 2 install the 3u enclosure back into the rack. 3 connect the ac power connector on the back panel of the 3u rackmount e...

  • Page 10

    10 installing the 3u rackmount enclosure in a rack lto-5 full-height tape drive installing the 3u rackmount enclosure in a rack the rack rails supplied with the 3u rackmount enclosure can be used to install the unit in racks that have round, square, or threaded holes in the vertical mounting bars. T...

  • Page 11

    Installing the 3u rackmount enclosure in a rack 11 lto-5 full-height tape drive caution: it is important to install rack components level. To ensure that the 3u rackmount enclosure is installed correctly it may be necessary to measure the height of the correct mounting holes in the front and rear ve...

  • Page 12

    12 installing the 3u rackmount enclosure in a rack lto-5 full-height tape drive figure 12 attaching the spring-loaded rails back of ra ck f ront of rack 5 repeat steps 4 and 5 for the second spring-loaded rack rail. 6 from the back of the rack, align the cable reel with the hole in the right spring-...

  • Page 13

    Installing the 3u rackmount enclosure in a rack 13 lto-5 full-height tape drive figure 14 attaching the cable rack bracket cable bracket 9 tighten the thumbscrew into the spring-loaded rack rail. 10 align the rear of the storage enclosure rails with the front end of the spring-loaded rack rails, the...

  • Page 14

    14 installing the 3u rackmount enclosure in a rack lto-5 full-height tape drive 12 connect a sas cable to the back of the 3u enclosure (see figure 1 on page 2) for every sas device in the 3u enclosure. 13 connect the power cable to the back of the 3u enclosure (see figure 2 on page 2). 14 secure the...

  • Page 15: Class A Device Declarations

    Class a device declarations 15 lto-5 full-height tape drive class a device declarations warning: this equipment has been tested and found to comply with the limits for a class a digital device pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against ha...

  • Page 16

    Backup. Recovery. Archive. It’s what we do. ©2010 quantum corporation. All rights reserved. Quantum, the quantum logo, and all other logos are registered trademarks of quantum corporation or of their respective owners. Protected by pending and issued u.S. And foreign patents, including u.S. Patent n...