Summary of QP2125
Page 1
Instruction manual quantum qp2000 series power amplifiers ver 1 sep 2010 qp2125 qp2250 qp2375 qp2500
Page 2
Parts identification 3 4 5 6 7 9 1 1 10 12 11 1 8 front view quantum qp2000 series of power amplifiers are the latest generation of power packs that had been developed through years of experience, countless feedbacks and limitless fine tuning of its predecessors, thus offering a new and unique audio...
Page 3
Amperes quantum qp2000 series power amplifiers page 3 parts identifications ( con’t ) t 5. Rs485 data link rs485 data port for parameter reading or controls from pc or external triggering panel. For pc link, a usb-rs485 converter shall be required whereas the software is available free. 6. Amp. Faul...
Page 4
Page 4 amperes electronics general schematic diagram - 2 power off select tuner cd cass off master music source sig in bass max min ext input max max min source min sig in chime mixer treble max min tone ctrl ch5 ch6 ch4 sig in sig in sig in max min max min min ch3 ch1 ch2 sig in sig in max min max ...
Page 5
Amperes quantum qp2000 series power amplifiers page 5 connecting the unit 1 audio from pre-amp mixer ( balanced line ) xlr connections duty amplifier unit duty amplifier unit standby amplifier 24v dc fr battery bank 100v line out to zone selector 100v out standby unit 100v line out standby 100v line...
Page 6
Page 6 amperes electronics connecting the unit - matrix paging e p 1 2 0 0 m in m ax m ax m in a nother q uality p roduct from s/n : input level siren message message siren message in pre in pre out remote trigger e r 1 1 0 8 o utput 4 o utput 3 o utput 2 o utput 1 o utput 5 o utput 6 o utput 7 o ut...
Page 7
Amperes quantum qp2000 series power amplifiers page 7 connecting the unit - uninterrupted paging a nother q u ality pro duct from m ains : 230v +/-10% m x 2 2 2 2 lin e out a c 50 / 60hz bg m r ec c hime m ixer p rio rity m ute c h.1 / 2 / ext.In aux cd m in max c h6 c h4 c h5 c h3 24v dc d c in put...
Page 8
Page 8 amperes electronics setting the unit firmware : v02.00 initialize ... Upon powering up the unit, the display shall appear as shown, initialising and into ready mode. Qp2000 ( 2 ) vol:20 t:26 displaying firmware version of the unit showing unit address in bracket, volume level and temperature ...
Page 9
Amperes quantum qp2000 series power amplifiers page 9 setting the unit - 2. Cascading 2. Cascade 2.1 unit set: 2 2. Cascade 3 select sub menu 2 for unit addressing use up and down button to select address number press menu button to confirm setting the address is used only when all the amplifiers at...
Page 10
Page 10 amperes electronics setting the unit - 2 4. System information 4. System info 4.1 main vol: 37.1v 4.2 i5 vol: 15.0v select sub menu 4 output voltage from 100v line terminal this menu provides information on various parameters such as input and output level and firmware version. 4.3 in signal...
Page 11
Rated output ( 100v line ) power requirement power consumption (240v ac ) standby power consumption standby current ( 240v ac ) full load current ( 240v ac ) 4 ohm output input sensitivity input gain control input connection tone controls fault sensing detection response fault contact freq. Response...
Page 12
Only amperes electronics service centres are allowed to make warranty repairs : a list of amperes electronics service centres may be asked for by the purchaser or send directly to amperes electronics sdn bhd at 70 jalan industri pbp 3, tmn perindustrian pusat bandar puchong, 47100, puchong, selangor...