1. DL manuals
  2. RAM
  3. Trucks
  4. Trucks 1500
  5. Owner's Manual

RAM Trucks 1500 Owner's Manual

Manual is about: 2016

Summary of Trucks 1500

  • Page 1

    1 5 0 0 / 2 5 0 0 / 3 5 0 0 chrysler group llc o w n e r ’ s m a n u a l 2 0 1 4 2014 ram truck 1500/2500/3500 14d241-126-aa first edition printed in u.S.A. R a m t r u c k.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .4 䡵 warnings and cautions . . . . . . . . . . . . . .6 䡵 van conversions/campers . . . . . . . . . . . .6 䡵 vehicle identification number . . . . . . . .6 䡵 vehic...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    1 introduction 5.

  • Page 8

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 9

    Frame and underbody as well as the automobile infor- mation disclosure label affixed to a window on your vehicle, the vehicle registration and title. Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seri...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ wireless ignition node (win) . . . . . . . . . . . . .12 ▫ keyless ignition node (kin) — if equipped . . .13 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ removing ke...

  • Page 12

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . .28 ▫ rke air suspension (remote lowering of the vehicle) — if equipped . . . . . . . . . . . . . . . . . .29 ▫ programming additional transmitters. . . . . . . .29 ▫ transmitter battery replacement . . . . . . . . . . .30 ▫ general informati...

  • Page 13

    ▫ enhanced seat belt use reminder system (beltalert®) . . . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ seat belts and pregnant women . . . . . . . . . . .68 ▫ seat belt extender . . . . . . . . . . . . . . . . . . . . .68 ▫ supplemental restraint system (srs) — air bags . . . . . . . . . . . ...

  • Page 14

    A word about your keys your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a either a bladed key with an immobilizer chip in it, or a key fob with remote keyless entry (rke) transmitter and an ignition node module (ignm). The key...

  • Page 15

    Keyless ignition node (kin) — if equipped this feature allows the driver to operate the ignition switch with the push of a button, as long as the remote keyless entry (rke) transmitter is in the passenger compartment. The keyless ignition node (kin) has four operating positions, three of which are l...

  • Page 16

    Key fob win key fob — if equipped the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stor...

  • Page 17

    Kin key fob — if equipped this kin key fob allows the driver to operate the ignition switch with the push of a button, as long as the remote keyless entry (rke) transmitter is in the passen- ger compartment. The keyless ignition node (kin) has four operating positions, three of which are labeled and...

  • Page 18

    Note: you can insert the double-sided emergency key into the lock cylinder with either side up once the start/stop button has been removed. Removing key fob from ignition place the shift lever in park (if equipped with an automatic transmission). Turn the key fob to the off position and then remove ...

  • Page 19

    Note: • the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the off position. Opening either front door will cancel this feature. Refer to “uconnect® settings” (engine off options) in “underst...

  • Page 20

    Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and push ignition button to place ignition in off position. When leaving the vehicle, always lock your ve- hicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. •...

  • Page 21

    Key-in-ignition reminder opening the driver’s door when the key fob is in the ignition and the ignition switch position is off or acc, a chime will sound to remind you to remove the key fob. Note: • ⬙keyed⬙ ignition systems will chime in off or acc when the driver door is open. • “keyless⬙ ignition ...

  • Page 22

    During normal operation, after turning on the ignition switch, the vehicle security light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb...

  • Page 23

    Caution! • always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unat- tended. • for vehicles equipped with keyless enter-n-go™, always remember to place the ignition in the off position. At the time of purchase, the original owner is provided with a four-digit pers...

  • Page 24

    Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Vehicle security alarm the vehicle security alarm monitors the vehicle doors and ignition for unauthorized operation. When the ve- hicle security al...

  • Page 25

    To disarm the system use the rke transmitter to unlock the door. If something has triggered the vehicle security alarm in your absence, the horn will sound three times when you unlock the doors and the exterior lights will blink three times. Check the vehicle for tampering. The vehicle security alar...

  • Page 26

    Note: • the front courtesy overhead console and door cour- tesy lights will not turn off if the dimmer control is in the “dome on” position (rotate horizontal thumb wheel on the bottom of the switch to the far right detent position). • the illuminated entry system will not operate if the dimmer cont...

  • Page 27

    Key fob with remote keyless entry (rke) transmitter (ignm) key fob with rke transmitter keyless enter-n-go™ fob (kin) 2 things to know before starting your vehicle 25.

  • Page 28

    Remote unlock the doors push and release the unlock button on the rke transmitter once to unlock the driver’s door. Push the unlock button twice within five seconds to unlock all doors, the tailgate and the rambox® (if equipped). The turn signal lights will flash to acknowledge the unlock signal. Th...

  • Page 29

    Flash lamps with remote key lock this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles not equipped with a touchscreen ra...

  • Page 30

    Note: pushing the lock button on the rke transmitter while you are in the vehicle will activate the vehicle security alarm system. Opening a door with the vehicle security alarm system activated will cause the alarm to sound. Push the unlock button to deactivate the vehicle security alarm system. Us...

  • Page 31

    Rke air suspension (remote lowering of the vehicle) — if equipped for easy entry and loading, your vehicle can be lowered by pressing the key fob air suspen- sion lowering button two times. When remote key fob lowering is requested, the vehicle will send a series of chirps and flashes to alert the c...

  • Page 32

    Transmitter battery replacement the recommended replacement battery is one cr2032 battery. Note: • perchlorate material — special handling may apply. See www.Dtsc.Ca.Gov/hazardouswaste/perchlorate • do not touch the battery terminals that are on the back housing or the printed circuit board. 1. Remo...

  • Page 33

    2. Separating rke halves requires screw removal – if equipped, and gently prying the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. Keyless ignition node (kin) emergency key removal remove screw from transmitter case 2 things to know before starting your ve...

  • Page 34

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery separating ignition no...

  • Page 35

    Clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4. To assemble the rke transmitter case, snap the two halves together, reposition and secure the screw as shown in step...

  • Page 36

    Note: • the vehicle must be equipped with an automatic transmission to be equipped with remote start. • obstructions between the vehicle and the rke trans- mitter may reduce this range. How to use remote start all of the following conditions must be met before the engine will remote start: • shift l...

  • Page 37

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 38

    • for security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the remote start mode. • the engine can be started two consecutive times (two 15-minute cycles) with the rke transmitter. However, the ignition switch must be cycled to the on/run position be...

  • Page 39

    The remote start comfort system can be activated and deactivated through the uconnect® system. For more information on remote start comfort system operation refer to ”customer programmable features” in “uconnect® settings” in “understanding your instru- ment panel”. Door locks manual door locks fron...

  • Page 40

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • for personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • before e...

  • Page 41

    Power door locks — if equipped a power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. If you press the power door lock switch while the key fob is in the ignition, and any front door is open, the power locks will not operate. This prevents you from ac...

  • Page 42

    Automatic doors unlock programming — if equipped the automatic doors unlock feature can be enabled or disabled as follows: • for vehicles not equipped with a touchscreen radio, refer to “electronic vehicle information center (evic)/settings (customer-programmable features)” in “understanding your in...

  • Page 43

    To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to engage and disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the u...

  • Page 44

    Keyless enter-n-go™ the passive entry system is an enhancement to the vehicle’s remote keyless entry (rke) system and a feature of keyless enter-n-go™. For further information, refer to “keyless enter-n-go™” in “starting and oper- ating”. This feature allows you to lock and unlock the vehicle’s door...

  • Page 45

    Note: if “unlock all doors 1st press” is programmed, all doors will unlock when you grab hold of the front driver’s door handle. To select between “unlock driver door 1st press” and “unlock all doors 1st press”, refer to “uconnect® settings” in “understanding your instru- ment panel” for further inf...

  • Page 46

    If one of the vehicle doors is open and the door panel switch is used to lock the vehicle, once all open doors have been closed the vehicle checks the inside and outside of the vehicle for any valid passive entry rke transmitters. If one of the vehicle’s passive entry rke transmitters is detected in...

  • Page 47

    Note: • after pressing the door handle lock button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • the pas...

  • Page 48

    Windows power windows — if equipped the control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of the quad cab and crew...

  • Page 49

    Warning! (continued) particularly unattended children, can become en- trapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto-down both the driver and front passenger window switch have an auto-down feature. Press the window switc...

  • Page 50

    Note: if the window runs into any obstacle during the auto-closure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window. Any impact due to rough road conditions may trigger the auto reverse function unex- pectedly during auto closu...

  • Page 51

    Window lockout switch (4–door models only) the window lockout switch on the driver’s door allows you to disable the window control on the rear passenger doors. To disable the window controls on the rear passenger doors, press the window lock button into the latched or down position. To enable the wi...

  • Page 52

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 53

    Please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible. If you will be carrying children too small for adult-sized seat belts, the seat belts or the lower anchors and tether for childr...

  • Page 54

    Children that are not big enough to wear the vehicle seat belt properly (see section on child restraints) should be secured in the rear seat in child restraints or belt- positioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly b...

  • Page 55

    Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belts even though you have air bags. • being too close to the steeri...

  • Page 56

    Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of in...

  • Page 57

    Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure ever...

  • Page 58

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as fa...

  • Page 59

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into...

  • Page 60

    Warning! (continued) • a belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause inter- nal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your...

  • Page 61

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt may not protect you properly. In a collisi...

  • Page 62

    Regular cab front center three point belt 1. The front center seat belt on the regular cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger ...

  • Page 63

    Inserting latch plate in use position 2 things to know before starting your vehicle 61.

  • Page 64

    Warning! • if the black latch and black buckle are not properly connected when the seat belt is used by an occu- pant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • when reattaching the black latch and black buckle, ensure the seat ...

  • Page 65

    Adjustable upper shoulder belt anchorage in the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that fits you best. As a guide, ...

  • Page 66

    Warning! • a lap belt worn too loose or too high is dangerous. • a belt worn too loose can allow you to slip down and under the belt in a collision. • a belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal inju...

  • Page 67

    If the passenger seating position is equipped with an alr and is being used for normal usage: only pull the belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a ratcheting sound as the belt retracts....

  • Page 68

    Warning! • the belt and retractor assembly must be replaced if the seat belt assembly automatic locking retractor (alr) feature or any other seat belt function is not working properly when checked according to the procedures in the service manual. • failure to replace the belt and retractor assembly...

  • Page 69

    Enhanced seat belt use reminder system (beltalert®) beltalert® is a feature intended to remind the driver and front passenger (if equipped with front passenger beltalert®) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted...

  • Page 70

    Seat belts and pregnant women we recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low ...

  • Page 71

    Note: the driver and front passenger advanced front air bags are certified to the new federal regulations for advanced air bags. The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severit...

  • Page 72

    This vehicle is equipped with supplemental seat- mounted side air bags (sab) to provide enhanced protection for an occupant during a side impact. The supplemental seat-mounted side air bags are located in the outboard side of the front seats. Note: • air bag covers may not be obvious in the interior...

  • Page 73

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 74

    Supplemental seat-mounted side air bags (sab) supplemental seat-mounted side air bags may provide enhanced protection to help protect an occupant during a side impact. The supplemental seat-mounted side air bag is marked with an air bag label sewn into the outboard side of the front seats. When the ...

  • Page 75

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the sab and sabic air bags during deployment could cause you to be severely injured or killed. • should a vehicle rollover occur, the pretensioners (if equipped) and/or ...

  • Page 76

    Warning! • if your vehicle is equipped with left and right supplemental side air bag inflatable curtain (sabic), do not stack luggage or other cargo up high enough to block the location of the sabic. The area where the sabic is located should remain free from any obstructions. • do not use accessory...

  • Page 77

    Along with seat belts and pretensioners, advanced front air bags work with the knee impact bolsters to provide improved protection for the driver and front passenger. Air bag deployment sensors and controls occupant restraint controller (orc) the orc is part of a federally regulated safety system re...

  • Page 78

    Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away from an inflating air bag. The orc monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the start or on/run position. If the key...

  • Page 79

    Driver and passenger advanced front air bag inflator units the driver and passenger advanced front air bag inflator units are located in the center of the steering wheel and on the right side of the instrument panel. When the orc detects a collision requiring the ad- vanced front air bags, it signal...

  • Page 80

    You if you are not seated properly, or if items are positioned in the area where the side air bag inflates. This especially applies to children. Supplemental side air bag inflatable curtain (sabic) inflator units — if equipped during collisions where the impact is confined to a particular area of th...

  • Page 81

    Enhanced accident response system in the event of an impact causing air bag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event the orc will determine whether to have the enhanced accident response system perform the follow- ing...

  • Page 82

    However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • as the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflati...

  • Page 83

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 84

    Air bag warning light you will want to have the air bags ready to inflate for your protection in a collision. The air bag warning light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. While the air bag system is designed to be maintenan...

  • Page 85

    • how various systems in your vehicle were operating; • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if at all) the driver was depressing the accelerator and/or brake pedal; and, • how fast the vehicle was traveling. These data can help provide a better unde...

  • Page 86

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to make sure you have the correct seat for your child. Carefully read and follow all the instructions and warnings in...

  • Page 87

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 88

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 89

    Older children and child restraints children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direc- tion are for children who are over two ye...

  • Page 90

    Warning! (continued) • after a child restraint is installed in the vehicle, do not move the vehicle seat forward or rearward because it can loosen the child restraint attach- ments. Remove the child restraint before adjusting the vehicle seat position. When the vehicle seat has been adjusted, reinst...

  • Page 91

    If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check belt fit peri- odically and make sure the seat belt buckle is latched. A child’s squirming or slouching can move the belt out of posi...

  • Page 92

    Recommendations for attaching child restraints — quad cab®/crew cab restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-f...

  • Page 93

    Recommendations for attaching child restraints — standard cab, mega cab® restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor r...

  • Page 94

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 95

    Latch positions for installing child restraints in this vehicle standard cab lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol quad cab®/crew cab full bench lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol 2 things to know before...

  • Page 96

    Quad cab®/mega cab®/crew cab split bench lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol 94 things to know before starting your vehicle.

  • Page 97

    Quad cab®/crew cab what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the...

  • Page 98

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 99

    Mega cab®/standard cab what is the weight limit (child’s weight + weight of the child re- straint) for using the latch an- chorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg)....

  • Page 100

    Can two child restraints be at- tached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchor- ages, use the seat belt to install a child seat in the center position next to a child...

  • Page 101

    Locating the latch anchorages — quad cab®/mega cab®/crew cab the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run you...

  • Page 102

    Locating the latch anchorages in addition, regular cab models have tether strap anchorages behind the front center and right seats. Quad cab®, mega cab® and crew cab models have tether strap anchorages lo- cated behind each of the rear seats. 1 — tether strap hook 2 — tether strap to child restraint...

  • Page 103

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing infant restraint...

  • Page 104

    Center seat latch — quad cab®/mega cab®/crew cab split bench if a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position, do not use that outboard position. If a child seat in the center position blocks the outboard latch anchors or seat bel...

  • Page 105

    4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 5. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 106

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • child restraint anchorages are...

  • Page 107

    Lap/shoulder belt systems for installing child restraints in this vehicle standard cab quad cab®/mega cab®/crew cab 2 things to know before starting your vehicle 105.

  • Page 108

    Quad cab®/crew cab what is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facin...

  • Page 109

    Mega cab®/standard cab what is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? 65 lbs (29.5 kg) the tether anchor can be used with the seat belt until the combined weight of the child and the...

  • Page 110

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 111

    8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test...

  • Page 112

    4. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat. 5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether str...

  • Page 113

    Installing child restraints using the top tether anchorage regular and mega cab® trucks: in the regular cab truck, the top tether anchorages are located behind the center and right passenger seats. In the mega cab truck, the top tether anchorages are located behind each rear seating position. There ...

  • Page 114

    2. Route the tether strap to provide the most direct path between the anchorage and the child seat. The tether strap should go between the head restraint posts underneath the head restraint. You may need to adjust the head restraint to the upward position to pass the tether strap underneath the head...

  • Page 115

    Warning! Never place a rear facing infant seat in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. Quad cab® or crew cab trucks: the top tether anchor- ages in this ...

  • Page 116

    2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the seat back, under the head restraint, through the tether strap loop behind the seat and over to the tether strap loop behind the center seat. 3. Pass the tether strap hook under the head restraint behind...

  • Page 117

    4. Attach the hook to the center tether strap loop (see diagram). Tighten the tether strap according to the child seat manufacturer’s instructions. Note: if there are child seats in both of the outboard (left and right) seating positions, the tether strap hooks of both child seats should be connecte...

  • Page 118

    Center seat: 1. Raise the head restraint and reach between the rear seat and rear glass to access the tether strap loop. 2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the seat back, under the head restraint, through the tether strap loop behind the sea...

  • Page 119

    4. Attach the hook to the outboard tether strap loop (see diagram). Tighten the tether strap according to the child seat manufacturer’s instructions. Tether strap through center tether strap loop tether strap through center tether strap loop and attached to outboard tether strap loop 2 things to kno...

  • Page 120

    Installing three child restraints: 1. Place a child restraint on each outboard rear seat. Route the tether straps following the directions for right and left seating positions, above. 2. Attach both hooks to the center tether strap loop, but do not tighten the straps yet. 3. Place a child restraint ...

  • Page 121

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 122

    The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to “maintenance procedures...

  • Page 123

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 124

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 125

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 126

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 127: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 ▫ inside day/night mirror — if equipped . . . .132 ▫ automatic dimming mirror — if equipped . . .132 ▫ automatic dimming mirror with rear view camera display — if equipped . . . ....

  • Page 128

    ▫ passenger’s power seat — if equipped . . . . . .149 ▫ power lumbar — if equipped . . . . . . . . . . . .150 ▫ heated seats — if equipped . . . . . . . . . . . . . .150 ▫ ventilated seats — if equipped . . . . . . . . . . . .153 ▫ manual seat adjuster — if equipped. . . . . . . .154 ▫ 40-20-40 fron...

  • Page 129

    ▫ lights-on reminder . . . . . . . . . . . . . . . . . . .175 ▫ battery saver. . . . . . . . . . . . . . . . . . . . . . . . .175 ▫ interior lights . . . . . . . . . . . . . . . . . . . . . . .175 ▫ cargo light . . . . . . . . . . . . . . . . . . . . . . . . .178 ▫ multifunction lever . . . . . . . ...

  • Page 130

    ▫ to accelerate for passing . . . . . . . . . . . . . . . .192 䡵 parksense® rear park assist — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .193 ▫ parksense® sensors . . . . . . . . . . . . . . . . . . . .193 ▫ parksense® warning display . . . . . . . . . . . . .194 ▫ parksense® d...

  • Page 131

    ▫ programming a non-rolling code . . . . . . . . .218 ▫ canadian/gate operator programming . . . . .219 ▫ using homelink® . . . . . . . . . . . . . . . . . . . .221 ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 ▫ troubleshooting tips . . . . . . . . . . . . . . . . . . .221 ▫...

  • Page 132

    䡵 storage . . . . . . . . . . . . . . . . . . . . . . . . . . . .236 ▫ glove compartment . . . . . . . . . . . . . . . . . . .236 ▫ door storage. . . . . . . . . . . . . . . . . . . . . . . . .238 ▫ center storage compartment — if equipped . .239 ▫ second row in-floor storage bin — if equipped . . ....

  • Page 133

    䡵 easy-off tailgate . . . . . . . . . . . . . . . . . . .265 ▫ disconnecting the rear camera or remote keyless entry — if equipped . . . . . . . . . . . . . . . . . . .265 ▫ removing the tailgate. . . . . . . . . . . . . . . . . .266 ▫ locking tailgate . . . . . . . . . . . . . . . . . . . . . .267 ...

  • Page 134

    Mirrors inside day/night mirror — if equipped a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror hea...

  • Page 135

    Left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you. Note: • the automatic dimming mirror feature is disabled when the vehicle is in reverse gear to improve re...

  • Page 136

    Assist call the rear view mirror contains an assist push button which automatically connects the vehicle occupants to one of several predefined locations for immediate sup- port: • roadside assistance – if you get a flat tire, or need a tow, just press the assist button and you’ll be con- nected to ...

  • Page 137

    • indication that the occupant placed a 9-1-1 call. • the vehicle brand. • the last known gps coordinates of the vehicle. 4. You should be able to speak with the 9-1-1 operator through the vehicle audio system to determine if additional help is needed. Note: once a connection is made between the veh...

  • Page 138

    Warning! (continued) • the 9-1-1 call system is embedded into the vehi- cle’s electrical system. Do not add aftermarket electrical equipment to the vehicle’s electrical sys- tem. This may prevent your vehicle from sending a signal to initiate an emergency call. To avoid inter- ference that can cause...

  • Page 139

    Warning! • ignoring the rearview mirror light could mean you will not have 9-1-1 call services. If the rearview mirror light is illuminated, have an authorized dealer service the 9-1-1 call system immediately. • the orc turns on the air bag warning light on the instrument panel if a malfunction in a...

  • Page 140

    Note: never place anything on or near the vehicle’s wireless and gps antennas. You could prevent wireless and gps signal reception, which can prevent your vehicle from placing an emergency call. Wireless and gps signal reception is required for the 9-1-1 call system to function properly. General inf...

  • Page 141

    Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they ...

  • Page 142

    Outside mirrors folding feature all outside mirrors are designed to be able to be manu- ally folded both forward and rearward to prevent dam- age. Caution! It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location. Tilt mirro...

  • Page 143

    If your vehicle is equipped with a touchscreen, this feature can be programmed through the uconnect® system. Refer to “uconnect® settings” in “understand- ing your instrument panel” for further information. If your vehicle is not equipped with a touchscreen, this feature can be programmed through th...

  • Page 144

    Resetting the power folding outside mirrors you may need to reset the power folding mirrors if the following occurs: • the mirrors are accidentally blocked while folding. • the mirrors are accidentally manually folded/ unfolded. • the mirrors come out of the unfolded position. • the mirrors shake an...

  • Page 145

    To adjust a mirror, press either the l (left) or r (right) button to select the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move power mirror controls 1 — mirror select buttons 2 — four-way mirror cont...

  • Page 146

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped). Refer to “rear window features” in “understanding the fea- tures of your vehicle” for further information. Driver’s outside automati...

  • Page 147

    “slide-on-rod” features of sun visor — if equipped the sun visor “slide-on-rod” feature allows for addi- tional flexibility in positioning the visor to block out the sun. To use the “slide-on-rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “slide-on-rod” until...

  • Page 148

    Trailer towing mirrors — if equipped these mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped in or out). Note: fold the trailer towing mirrors rearwa...

  • Page 149

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 150

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 151

    Warning! (continued) • do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Caution! Do not place any article under a power seat or impede its abili...

  • Page 152

    Power lumbar — if equipped vehicles equipped with power driver or passenger seats may be also be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat. Push the switch forward to increase the lumbar support. Push the switch rearward to decrease the lum...

  • Page 153

    Front heated seats the front heated seats control buttons are located on the center instrument panel below the climate controls. If your vehicle is equipped with a touchscreen, the front heated seats control buttons are located within the cli- mate or controls screen of the touchscreen. • press the ...

  • Page 154

    Vehicles equipped with remote start on models that are equipped with remote start, the heated seats can be programed to come on during a remote start. If your vehicle is equipped with a touchscreen, this feature can be programmed through the uconnect® system. Refer to “uconnect® settings” in “unders...

  • Page 155

    Note: • once a heat setting is selected, heat will be felt within two to five minutes. • the engine must be running for the heated seats to operate. When the high-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output...

  • Page 156

    Note: the engine must be running for the ventilated seats to operate. Vehicles equipped with remote start on models that are equipped with remote start, the ventilated seats can be programed to come on during a remote start. If your vehicle is equipped with a touchscreen, this feature can be program...

  • Page 157

    While sitting in the seat, pull up on the handle and slide the seat forward or backward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! • adjusting a seat while dri...

  • Page 158

    40-20-40 front bench seat — if equipped the seat is divided into three segments. The outboard seat portions are each 40% of the total width of the seat. On some models the back of the center portion (20%) easily folds down to provide an armrest/center storage compartment. Mega cab® rear seat feature...

  • Page 159

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Folding rear seat (table mode) — if equipped both the left and right rear seatbacks ca...

  • Page 160

    3. Lift the seatback, to return the seat to the upright position. Be sure the seatback is locked in place. Folding rear seat — if equipped both the outboard rear seats will drop and move forward when the seatback is folded flat. Warning! • it is dangerous to ride in a cargo area, inside or outside o...

  • Page 161

    Warning! (continued) • cargo must be securely tied down before driving your vehicle. Improperly secured cargo can fly around in a sudden stop or collision and strike someone in the vehicle, causing serious injury or death. To fold either rear seat flat: 1. Lift the handle, located on the outboard si...

  • Page 162

    3. Lift the seatback, to return the seat to the upright position. Be sure the seat is locked in place. Warning! An improperly latched seat could cause serious in- jury or death. Make sure that the seatback is securely locked into position. If the seatback in not securely locked into position the sea...

  • Page 163

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 164

    Note: • the rear center head restraint (crew cab and quad cab) has only one adjustment position that is used to aid in the routing of a tether. Refer to “occupant restraints” in “things to know before starting your vehicle” for further information. • the head restraints should only be removed by qua...

  • Page 165

    The memory seat buttons are located on the outboard side of the drivers seat cushion. Programming the memory feature note: to create a new memory profile, perform the following: vehicles equipped with keyless enter-n-go 1. Without pressing the brake pedal, push the engine start/stop button and cycle...

  • Page 166

    Vehicles not equipped with keyless enter-n-go 1. Insert the ignition key fob, and turn the ignition switch to the on/run position. 2. Adjust all memory profile settings to desired prefer- ences (seat, side mirrors, adjustable pedals [if equipped], power tilt and telescopic steering column [if equipp...

  • Page 167

    To program your rke transmitters, perform the follow- ing: 1. Cycle the vehicles ignition to the off position. 2. Select desired memory profile (1) or (2). Note: if a memory profile has not already been set, refer to ⬙programming the memory feature⬙ for instructions on how to set a memory profile. 3...

  • Page 168

    Driver two memory position recall • to recall the memory setting for driver two using the memory switch, press memory button number 2 on the memory switch. • to recall the memory settings for driver two using the rke transmitter, press the unlock button on the rke transmitter linked to memory positi...

  • Page 169

    • when you remove the key fob from the ignition (or change the ignition to off, for vehicles equipped with keyless enter-n-go™), the driver seat will move to a position 0.3 in (7.7 mm) forward of the rear stop if the driver seat position is between 0.9 in and 2.7 in (22.7 mm and 67.7 mm) forward of ...

  • Page 170

    To open and close the hood to open the hood, two latches must be released. 1. Pull the hood release lever located below the steering wheel at the base of the instrument panel. 2. Reach into the opening beneath the center of the hood and push the safety latch lever to the left to release it, before r...

  • Page 171

    Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle...

  • Page 172

    Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less suscep- tible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility ...

  • Page 173

    When the system is on, the headlight delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch to the off position. To turn the automatic headlights off, turn the headlight switch out of the auto position. Note: the engine must be runnin...

  • Page 174

    If your vehicle is not equipped with a touchscreen, this feature can be programmed through the electronic ve- hicle information center (evic). Refer to “electronic vehicle information center (evic)” in “understanding your instrument panel” for further information. Daytime running lights (drl) — if e...

  • Page 175

    Automatic high beam headlamp control — if equipped the automatic high beam headlamp control system provides increased forward lighting at night by automat- ing high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle specific light and ...

  • Page 176

    Parking lights and panel lights to turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the o (off) position. Fog lights — if equipped the fog lights are turned on by rotating the headlight ...

  • Page 177

    Turn off when the switch is pushed a second time, when the headlight switch is rotated to the off position, or the high beam is selected. Lights-on reminder if the headlights, parking lights, or cargo lights are left on after the ignition is turned off, a chime will sound when the driver’s door is o...

  • Page 178

    Allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. The brightness of the instrument panel as well as the ambient lighting can be regulated by rotating the dimmer control right (brighter) or left (dimmer). When the head- lights are on you can supplem...

  • Page 179

    (rke) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens. Note: the courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the int...

  • Page 180

    Ambient light the overhead console is equipped with an ambient light feature. This light casts illumination for improved visibil- ity of the floor console area. Cargo light the cargo lights are turned on by pressing on the cargo button. The cargo lights will also turn on for approximately 30 seconds...

  • Page 181

    Multifunction lever the multifunction lever is located on the left side of the steering column. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light re...

  • Page 182

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Flash-to-pass you can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer-...

  • Page 183

    Windshield wiper operation rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation. Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper opera- tion. Intermittent wiper system the inte...

  • Page 184

    Depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released. It will then resume the intermittent interval previously selected. If the washer knob is pushed while in the off position, the wiper will turn on and cycle approximately three times afte...

  • Page 185

    Rain sensing wipers — if equipped this feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of ...

  • Page 186

    The rain sensing system has protection features for the wiper blades and arms, and will not operate under the following conditions: • low ambient temperature — when the ignition is first turned on, the rain sensing system will not operate until the wiper switch is moved, vehicle speed is greater tha...

  • Page 187

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Heated steering wheel — i...

  • Page 188

    The heated steering wheel control button is located on the center of the instrument panel below the climate controls. If your vehicle is equipped with a touchscreen, the heated steering wheel control button is located within the cli- mate or controls screen of the touchscreen. • press the heated ste...

  • Page 189

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures,...

  • Page 190

    • the pedals can be adjusted with the ignition off. • the pedals cannot be adjusted when the vehicle is in reverse or when the electronic speed control sys- tem is on. The following messages will be displayed on vehicles equipped with the electronic vehicle informa- tion system (evic) if the pedals ...

  • Page 191

    Caution! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path. Warning! Do not adjust the pedals while the vehicle is ...

  • Page 192

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 193

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate the electronic speed control with- out erasing the set speed memory. Pressing the on/off button or turning the ignition switch off erases the set speed memory. T...

  • Page 194

    To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set (-) button. The speed decrement shown is dependant on the speed of u.S. (mph) or metric (km/h) units: u.S. Speed (mph) • pressing the set (-) button once will result in a 1 mph decrease in set spe...

  • Page 195

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 196

    (150 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orienta- tion of the obstacle. Parksense® warning display the parksense® warning screen is located within the electronic vehicle information center (evic). It provides visual warnings to indicate th...

  • Page 197

    Single 1/2 second tone slow tone 3 understanding the features of your vehicle 195.

  • Page 198

    Fast tone continuous tone 196 understanding the features of your vehicle.

  • Page 199

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-45 in (200-115 cm) ...

  • Page 200

    Enabling and disabling parksense® parksense® can be enabled and disabled with the parksense® switch. When the parksense switch is pressed to dis- able the system, the instrument cluster will display the “parksense off” message for approximately five seconds. Refer to “elec- tronic vehicle informatio...

  • Page 201

    Reverse and the system has detected a faulted condi- tion, the evic will display the ⬙parksense unavail- able wipe rear sensors ⬙ or the ⬙parksense un- available service required ⬙ message for as long as the vehicle is in reverse. Under this condition, parksense® will not operate. If ⬙parksense unav...

  • Page 202

    • when you move the shift lever to the reverse position and parksense® is turned off, the instrument cluster will display ⬙parksense off⬙ message for as long as the vehicle is in reverse. • parksense®, when on, will reduce the volume of the radio when it is sounding a tone. • clean the parksense® se...

  • Page 203

    Caution! (continued) • the vehicle must be driven slowly when using parksense® in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using parksense®. Warning! • drivers must be careful when backing up even when using par...

  • Page 204

    Parksense® front and rear park assist — if equipped the parksense® park assist system provides visual and audible indications of the distance between the rear and/or front fascia and a detected obstacle when backing up or moving forward, e.G. During a parking maneuver. Refer to parksense® system usa...

  • Page 205

    Parksense® warning display the parksense® warning screen is located within the electronic vehicle information center (evic). It provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the de- tected obstacle. Refer to “electronic vehicle inform...

  • Page 206

    The vehicle is close to the obstacle when the evic display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-45 in (200-115 cm) 45-31...

  • Page 207

    Front park assist audible alerts parksense® will turn off the front park assist audible alert (chime) after approximately three seconds when an obstacle has been detected, the vehicle is stationary, and brake pedal is applied. Adjustable chime volume settings front and rear chime volume settings can...

  • Page 208

    When the shift lever is moved to reverse and the front or rear system is disabled, the evic will display the ⬙front parksense off⬙ or ⬙rear parksense off⬙ message for five seconds, followed by a car graphic with ⬙off⬙ in the corresponding side. This car graphic will be displayed for as long as the v...

  • Page 209

    Arc alerts will interrupt the ⬙parksense unavail- able wipe rear sensors ⬙, ⬙parksense unavail- able wipe front sensors ⬙, or ⬙parksense un- available service required ⬙ messages if an object is detected within the five second pop-up duration. The car graphic will remain displayed for as long as the...

  • Page 210

    • when you turn front or rear parksense® off, the instrument cluster will display “front parksense off” or “rear parksense off.” furthermore, once you turn front or rear parksense® off, it remains off until you turn it on again, even if you cycle the ignition key. • when you move the shift lever to ...

  • Page 211

    Caution! • parksense® is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • the vehicle m...

  • Page 212

    Warning! (continued) • before using parksense®, it is strongly recom- mended that the ball mount and hitch ball assem- bly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be...

  • Page 213

    When the vehicle is shifted out of reverse (with camera delay turned on), the rear camera image will be dis- played for up to 10 seconds after shifting out of ⬙re- verse ⬙ unless the forward vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into ⬙park⬙ or the ignition is switched to...

  • Page 214

    Warning! Drivers must be careful when backing up even when using the parkview® rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your ...

  • Page 215

    • power sliding rear window switch — if equipped • universal garage door opener — if equipped courtesy/reading lights both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light ...

  • Page 216

    Note: the courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the ignition is turned off, they will automatically turn off after 15 minutes. Garage door opener — if...

  • Page 217

    Note: homelink® is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink® ensure your vehicle is parked outside of the garage before you begin programming. For efficient programming and accurate transmission of the radio-frequency signal it is recommended that a...

  • Page 218

    Note: • erasing all channels should only be performed when programming homelink® for the first time. Do not erase channels when programming additional buttons. • if you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on the internet at www.Homelink.Com for informat...

  • Page 219

    1. Turn the ignition switch to the on/run position. 2. Place the hand - held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program. 3. Simultaneously press and hold both the homelink® button you want to program and the hand - held transmitter button. 4. Continue to...

  • Page 220

    To program the remaining two homelink® buttons, repeat each step for each remaining button. Do not erase the channels. Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and...

  • Page 221

    Note: • it may take up to 30 seconds or longer in some cases for the channel to train. • if the evic displays “did not train” repeat from step 2. 5. Press and hold the programmed homelink® button. The evic will display “channel # transmit.” if the garage door opener/device activates, program- ming i...

  • Page 222

    It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. 1. Turn the ignition switch to the on/run position. 2. Place the hand - held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program. 3...

  • Page 223

    Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink® button until the evic displays “channel # training” do not release the button. 3. Without r...

  • Page 224

    • press the learn button on the garage door opener to complete the training for a rolling code. • did you unplug the device for programming and remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on the internet at www.Homelink.Com f...

  • Page 225

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 226

    Power sunroof — if equipped the power sunroof switch is located on the overhead console between the courtesy/reading lights. Warning! • never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to ...

  • Page 227

    Warning! (continued) • do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. Injury may result. Opening sunroof — manual mode to open the sunroof, press and hold the switch rearward to full open. Any rel...

  • Page 228

    Pinch protect feature this feature will detect an obstruction in the opening of the sunroof during express close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and ...

  • Page 229

    Sunroof maintenance use only a nonabrasive cleaner and a soft cloth to clean the glass panel. Ignition off operation the power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the lock position. Opening either front door will cancel this fe...

  • Page 230

    The auxiliary power outlets can be found in the following locations: caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watts (13 amps) power rating is exceeded, the fuse protecting the system will need to be replaced. • power outlets are designed for accessory...

  • Page 231

    • center console when equipped with bucket seats. • inside the upper lid of the center storage compartment — if equipped. Power outlet — center console power outlet — upper lid 3 understanding the features of your vehicle 229.

  • Page 232

    • rear of the center console storage compartment — quad cab® or crew cab. The key symbol indicates that this outlet can supply power when the key is in the on/run or acc posi- tions. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect ...

  • Page 233

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 234

    Power inverter — if equipped a 115 volt (150 watts maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 watts. Certain high-end video games, such as ...

  • Page 235

    To turn on the power outlet, simply plug in the device. The outlet automatically turns off when the device is unplugged. Note: due to built-in overload protection, the power inverter will shut down if the power rating is exceeded. Warning! To avoid serious injury or death: • do not insert any object...

  • Page 236

    Front instrument panel cupholders — floor mounted shifter for vehicles equipped with bucket seats there are two cupholders located in the floor console. Rear cupholder — quad cab® quad cab® vehicles may be equipped with a rear cupholder that consists of two cup wells for rear passen- ger convenience...

  • Page 237

    Rear cupholder — crew cab crew cab vehicles are equipped with rear cupholders located in the center armrest. Crew cab vehicles may be equipped with a rear cup- holder that consists of two cup wells for rear passenger convenience. Crew cab rear armrest cupholder rear cup wells 3 understanding the fea...

  • Page 238

    Storage glove compartment the glove compartment is located on the passenger side of the instrument panel and features both an upper and lower storage area. Glove compartment 1 — upper glove compartment 2 — lower glove compartment 236 understanding the features of your vehicle.

  • Page 239

    To open the upper glove compartment push upward on the handle release. The glove compartment door will automatically open. To open the lower glove compartment, pull on the handle to release the latch and lower the glove compartment door. Upper glove compartment lower glove compartment 3 understandin...

  • Page 240

    Door storage front door storage — if equipped storage areas and bottle holders (drivers side only) are located in the door trim panels. Rear door storage — crew cab storage compartments are located in both the driver and passenger door trim panels. Front door storage rear door storage 238 understand...

  • Page 241

    Center storage compartment — if equipped the center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. Warning! • this armrest is not a seat. Anyone seated on the armrest could be seri...

  • Page 242

    With the upper lid closed, pull on the lower handle to open the lower storage bin. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Upper storage compartment lower storage bi...

  • Page 243

    Second row in-floor storage bin — if equipped in-floor storage bins are located in front of the second row seats and can be used for extra storage. The storage bins have removable liners that can be easily removed for cleaning. To open in-floor storage bin, lift upward on the handle of the latch and...

  • Page 244

    Seatback storage located in the back of both the driver and passenger front seats are pockets that can be used for storage. Storage (regular cab) the storage bin is located behind the front seats and runs the length of the cab. Drivers side seatback storage storage bin 242 understanding the features...

  • Page 245

    Storage and seats (crew cab) the crew cab models provide additional storage under the rear seats. Lift the seats to access the storage com- partment. To open the storage compartments, lift upward on the handle of the latch and open the lid. Caution! Always lift the storage compartment lids by using ...

  • Page 246

    Plastic grocery bag retainers (regular cab models) retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat. Rear window features rear window defroster the rear window defroster button is located on the climate control panel. Press thi...

  • Page 247

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 248

    Manual sliding rear window — if equipped a locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. Fold flat load floor — if equipped quad cab® and crew cab models with a 60/40 rear seat may be equipped with a folding lo...

  • Page 249

    3. Reverse the procedure to store the load floor. Positioning the load floor for storage access under the seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load fl...

  • Page 250

    4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle. Pickup box the pickup box has many features designed for utility and convenience. Load floor securing straps pick up box features 1 — upper load floor indents 2 — bulk head dividers 3 — c...

  • Page 251

    Note: if you are installing a toolbox, ladder rack or headache rack at the front of the pickup box, you must use mopar box reinforcement brackets that are available from your authorized dealer. You can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor. Place l...

  • Page 252

    There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box. There are four tie-down cleats bolted to the lower sides of the picku...

  • Page 253

    Note: the cargo camera image may be deactivated by touching the uconnect® display. The previous selected screen will appear. Rambox® — if equipped the rambox® system is an integrated pickup box stor- age and cargo management system consisting of three features: • integrated box side storage bins • c...

  • Page 254

    Caution! Failure to follow the following items could cause damage to the vehicle: • assure that all cargo inside the storage bins is properly secured. • do not exceed cargo weight rating of 150 lb (68 kg) 1500 series vehicles or 300 lbs (136 kg) for 2500 and 3500 series vehicles per bin. To open a s...

  • Page 255

    The interior of the rambox® will automatically illumi- nate when the lid is opened. In addition to the automatic illumination switch, there is a manual on/off switch located at the rear of each storage bin. Pushing the switch once will turn off the bin lights, pushing the switch again will turn the ...

  • Page 256

    Caution! (continued) it is recommended that the bin lights be turned off manually using the on/off switch. Cargo bins feature two removable drain plugs (to allow water to drain from bins). To remove plug, pull up on the edge. To install push plug downward into drain hole. Note: provisions are provid...

  • Page 257

    Rambox® safety warning carefully follow these warnings to help prevent personal injury or damage to your vehicle: warning! • always close the storage bin covers when your vehicle is unattended. • do not allow children to have access to the storage bins. Once in the storage bin, young children may no...

  • Page 258

    Note: in the event of an individual being locked inside the storage bin, the storage bin cover can be opened from inside of the bin by pulling on the glow-in-the-dark lever attached to the storage bin cover latching mechanism. Bed extender — if equipped the bed extender has three functional position...

  • Page 259

    2. With the side gates open, position the extender fully forward in the bed against the front panel. 3. Rotate the side gates closed allowing the outboard ends to be positioned in front of the cargo tie down loops. 4. Rotate the center handle horizontally to secure the side gates in the closed posit...

  • Page 260

    5. Lock the center handle using the vehicle key to secure the panel into place. Divider position the divider position is intended for managing your cargo and assisting in keeping cargo from moving around the bed. There are 11 divider slots along the bed inner panels which allow for various positions...

  • Page 261

    2. With the side gates open, position the extender so the outboard ends align with the intended slots in the sides of the bed. 3. Rotate the side gates closed so that the outboard ends are secured into the intended slots of the bed. 4. Rotate the center handle horizontally to secure the side gates i...

  • Page 262

    5. Lock the center handle to secure the panel into place. Extender position the extender position allows you to load the bed of the truck beyond the tail gate. The bed extender will add an additional 15 in (38 cm) in the back of the truck when additional cargo room is needed. The extender position u...

  • Page 263

    2. Make sure the center handle is unlocked and rotate the center handle vertically in order to release the ex- tender side gates. 3. Fit the end of the side gate ends onto the pin and handle. 4. Rotate the handles to the horizontal position to secure into place. Extender installation locking tab 3 u...

  • Page 264

    Warning! To reduce the risk of potential injury or property damage: • cargo must be secured. • do not exceed cargo load rating of your vehicle. • secure all loads to truck utilizing cargo tie downs. • extender should not be used as cargo tie down. • when vehicle is in motion do not exceed 150 lbs (6...

  • Page 265

    Each cleat must be located and tightened down in one of the detents, along either rail, in order to keep cargo properly secure. To move the cleat to any position on the rail, turn the nut counterclockwise, approximately three turns. Then pull out on the cleat and slide it to the detent nearest the d...

  • Page 266

    To remove the cleats from the utility rail, remove the end cap screw located in the center of the end cap, using a #t30 torx® head driver. Remove the end cap and slide the cleat off the end of the rail. Slide-in campers camper applications certain truck models are not recommended for slide-in camper...

  • Page 267

    Easy-off tailgate to simplify mounting of a camper unit with an overhang, the tailgate can be removed. Note: if your vehicle is equipped with a rear camera or rke the electrical connector must be disconnected prior to removing the tailgate. Disconnecting the rear camera or remote keyless entry — if ...

  • Page 268

    3. Disconnect the chassis wiring harness, ensuring the connector bracket does not fall into the sill. 4. Connect the chassis plug and bracket (provided in the glove box) to the chassis wiring harness and insert the bracket back into the sill. 5. Connect the tailgate plug (provided in the glove box) ...

  • Page 269

    3. Raise the tailgate to a 45 degree angle. 4. Raise the right side of the tailgate until the right side pivot clears the hanger bracket. 5. Slide the entire tailgate to the right to free the left side pivot. 6. Remove the tailgate from the vehicle. Note: do not carry the tailgate loose in the truck...

  • Page 270

    Tri-fold tonneau cover — if equipped your vehicle may be equipped with a tri-fold tonneau cover which consists of different features: • easy tri-fold cover • tonneau fore aft locator • crosscar inside bed locator • front and rear clamps • stowage strap • locking capability note: the tonneau cover ca...

  • Page 271

    2. Pull down on the first set of clamps on both driver and passenger sides to the semi clamped position. 3. Pull down on the clamp wire and push the clamp up into the proper released position. Note: be sure the clamp and clamp wire is in the proper released position. Semi clamped position proper rel...

  • Page 272

    Caution! Make sure the tonneau cover clamp and clamp wire is in the proper released position. If the clamp and clamp wire is not properly released, damage to the tonneau cover material will result. 4. Pick up on the tonneau cover and fold it back into the second panel. 5. Pick up on the cover and fo...

  • Page 273

    7. Pull down on the clamp wire and push the clamp up into the proper released position. 8. Be sure to clip both stowage straps together to insure the cover stays together. Semi clamped position proper released position 3 understanding the features of your vehicle 271.

  • Page 274

    9. With two people remove the cover. Note: be sure the tonneau cover has been folded completely before removing. Tri-fold tonneau cover installation to install the tonneau cover follow the following steps: 1. Position the folded tonneau cover on the truck bed and push the cover forward against the f...

  • Page 275

    3. Push clamp wires up and under the flange of box (or flange of ram box rail, if equipped) to the semi clamped position. Stowed position semi clamped position 3 understanding the features of your vehicle 273.

  • Page 276

    4. Push clamp handles upward to the clamped position to properly engage the clamps. Note: once clamped, be sure the clamps are not par- tially clamped to the truck bed flange. Clamped position improper clamp position 274 understanding the features of your vehicle.

  • Page 277

    5. Disengage the stowage straps. 6. Unfold tonneau cover to the intermediate position. Note: the vehicle cannot be driven when the tonneau cover is in this position. 7. Completely unfold the tonneau cover. Intermediate position (vehicle cannot be driven) fully unfolded position 3 understanding the f...

  • Page 278

    8. Pull down on the second set of clamp handles to release the clamps from the stowed position. 9. Push clamp wires up and under the flange of box (or flange of ram box rail, if equipped) to the semi clamped position. Stowed position semi clamped position 276 understanding the features of your vehic...

  • Page 279

    10. Push clamp handles upward to the clamped position to properly engage the clamps. Note: once clamped, be sure the clamps are not par- tially clamped to the truck bed flange. Clamped position improper clamp position 3 understanding the features of your vehicle 277.

  • Page 280

    The tonneau cover clamps can be locked when in the clamped position by placing a lock through the locking hole. Caution! It is the driver’s responsibility to ensure the tonneau cover is properly installed on the vehicle. Failure to follow this procedure can result in detachment of the tonneau cover ...

  • Page 281: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .281 䡵 instrument cluster — midline . . . . . . .282 䡵 instrument cluster — premium . . . . . . .283 䡵 instrument cluster descriptions . . . . .284 䡵 electronic vehicle information center (evic) . . . . . . . ...

  • Page 282

    䡵 ipod®/usb/mp3 control — if equipped . .357 䡵 steering wheel audio controls — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .358 ▫ radio operation . . . . . . . . . . . . . . . . . . . . . .359 ▫ cd player. . . . . . . . . . . . . . . . . . . . . . . . . . .359 䡵 cd/dvd disc maint...

  • Page 283

    Instrument panel features 1 — headlight switch 7 — 115v power inverter outlet 13 — gear selector/transfer case position switch — if equipped 2 — instrument cluster 8 — power outlet — if equipped 14 — ignition switch 3 — radio 9 — lower switch bank 15 — hood release 4 — hazard switch 10 — instrument ...

  • Page 284

    Instrument cluster — midline 282 understanding your instrument panel.

  • Page 285

    Instrument cluster — premium 4 understanding your instrument panel 283.

  • Page 286

    Instrument cluster descriptions 1. Tachometer the tachometer indicates engine speed in revolutions per minute (rpm x 1000). Caution! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine operation over 3200 rpm (redline) can result in significant damage that ...

  • Page 287

    Testing the light will come on when the ignition is first turned on and remain on for 15 seconds, then blink for 5 seconds, and remain on until the vehicle is started. If the bulb does not come on during starting, have the condi- tion investigated promptly. If this light comes on and remains on whil...

  • Page 288

    Note: • a continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. • check for an inoperative outside light bulb if either indicator remains on and does not flash, or flashes at a rapid rate. 5. Voltmeter when the engine is running, the gauge indicat...

  • Page 289

    Hydraulic system malfunction or that a problem with the brake booster has been detected by the anti-lock brake system (abs) / electronic stability control (esc) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ...

  • Page 290

    Unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the ...

  • Page 291

    10. Oil pressure gauge — if equipped the pointer should always indicate some oil pres- sure when the engine is running. A continuous high or low reading under normal driving conditions may indi- cate a lubrication system malfunction. Immediate service should be obtained from an authorized dealer. 11...

  • Page 292

    16. Tire pressure monitoring telltale light — if equipped each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (if your vehicle has tir...

  • Page 293

    Of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the tpms from functioning properly. Always check the tpms malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires...

  • Page 294

    Note: the highest available transmission gear is dis- played in the lower right corner of the electronic vehicle information center (evic) whenever the electronic range select (ers) feature is active. Use the +/- selector on the shift lever to activate ers. Refer to “automatic transmission” in “star...

  • Page 295

    Note: • the “esc off indicator light” and the “esc activation/malfunction indicator light” come on momentarily each time the ignition switch is turned to on/run. • each time the ignition is turned to on/run, the esc system will be on, even if it was turned off previously. • the esc system will make ...

  • Page 296

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “maintaining your vehicle.” follow the warnings unde...

  • Page 297

    If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough ...

  • Page 298

    32. 4wd auto indicator light — if equipped this light alerts the driver that the vehicle is in the four-wheel drive auto mode, and the front axle is engaged, but the vehicle’s power is sent to the rear wheels. Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction....

  • Page 299

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic menu items consists of the following: • digital speedometer • vehicle info • fuel economy info • trip a • trip b •...

  • Page 300

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: • up arrow button press and release the up arrow button to scroll upward through the main menu and sub- menus (fuel economy, trip a, trip b, audio, stored messages, screen set up). • d...

  • Page 301

    • select/right arrow button press and release the select/right arrow button to access/select the information screens or sub-menu screens of a main menu item. Press and hold the select/right arrow button for two seconds to reset displayed/selected fea- tures that can be reset. • left arrow button pre...

  • Page 302

    The evic displays are located in the center portion of the cluster and consists of seven sections: 1. Compass display displays the current direction. For further information, refer to “compass settings” under “customer program- mable features — uconnect® 5.0/8.4 settings”. 2. Temperature display dis...

  • Page 303

    • windshield washer fluid low indicator this telltale will turn on to indicate the wind- shield washer fluid is low. • low coolant level indicator this telltale will turn on to indicate the vehicle coolant level is low. • transmission temperature warning telltale this telltale indicates that the tra...

  • Page 304

    Protection mode will automatically be selected in order to “protect” the air suspension system, air suspension adjustment is limited due to payload. • service stop/start system telltale — if equipped this telltale will turn on to indicate that the stop/start is unavailable, service stop/start system...

  • Page 305

    6. Evic red telltales • door ajar this light will turn on to indicate that one or more doors may be ajar. • oil pressure warning light this telltale indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will soun...

  • Page 306

    If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the park position. The light should turn off. If the light remains lit with the engine running, your vehicle will usually be d...

  • Page 307

    • trailer brake disconnected warning light this telltale is on when the trailer brake has been disconnected. 7. Audio/phone information and sub-menu information whenever there are sub-menus available, the position within the sub-menu is shown here. The main display area will normally display the mai...

  • Page 308

    • five second unstored messages when the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns to the previous screen. An example of this message type is “automatic high beams on”. Fuel filter life reset the cluster will display t...

  • Page 309

    2. Press and release the down arrow button to scroll downward through the main menu to “vehicle info”. 3. Press and release the right arrow button to access the ”fuel filter life” screen. 4. Press and release the down arrow button to select “reset”, then press and release the right arrow button to s...

  • Page 310

    4. Press and release the down arrow button to select “reset”, then press and release the right arrow button to select reset of the oil life to 100%. 5. Press and release the up arrow button to exit the evic screen. Vehicles not equipped with passive entry 1. Without pressing the brake pedal, press t...

  • Page 311

    Electronic vehicle information center (evic) displays — 7” display the evic displays are located in the center portion of the cluster and consists of eight sections: 1. Main screen — the inner ring of the display will illuminate in grey under normal conditions, yellow for non critical warnings, red ...

  • Page 312

    8. 4wd status 9. Selectable gauge 2 10. Selectable gauge 1 11. Selectable gauge 1 the main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warn- ing...

  • Page 313

    • five second unstored messages when the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns to the previous screen. An example of this message type is “automatic high beams on”. Evic amber telltales this area will show reconfig...

  • Page 314

    Caution! Continuous driving with the transmission tempera- ture warning light illuminated will eventually cause severe transmission damage or transmission failure. Warning! If you continue operating the vehicle when the transmission temperature warning light is illumi- nated you could cause the flui...

  • Page 315

    Evic white telltales • electronic speed control ready this light will turn on when the electronic speed control is on. For further information, refer to “electronic speed control” in “under- standing the features of your vehicle.” evic red telltales this area will show reconfigurable red telltales. ...

  • Page 316

    Electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain service immediately. See an autho- rized dealer. If jump starting is required, refer to “jump starting procedures” i...

  • Page 317

    If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into neutral and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “if...

  • Page 318

    Vehicles equipped with passive entry 1. Without pressing the brake pedal, press the engine start/stop button and cycle the ignition to the on/run position (do not start the engine.) 2. Press and release the down arrow button to scroll downward through the main menu to “vehicle info”. 3. Press and re...

  • Page 319

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Oil life reset your vehicle is equipped with an engine oil change indicator system. The “oil change required” message will flash in the evic disp...

  • Page 320

    Vehicles not equipped with passive entry 1. Without pressing the brake pedal, cycle the ignition to the on/run position (do not start the engine.) 2. Press and release the down arrow button to scroll downward through the main menu to “ vehicle info”. 3. Press and release the right arrow button to ac...

  • Page 321

    • service antilock brake system • service electronic throttle control • service power steering • cruise off • cruise ready • cruise set to xxx mph • tire pressure screen with low tire(s) “inflate tire to xx” • service tire pressure system • parking brake engaged • brake fluid low • service electroni...

  • Page 322

    • remote start aborted door open • remote start aborted hood open • remote start aborted trunk open • remote start aborted time expired • remote start disabled start to reset • service airbag system • service airbag warning light • driver seatbelt unbuckled • passenger seatbelt unbuckled • front sea...

  • Page 323

    • service air suspension system • normal ride height achieved • aerodynamic ride height achieved • off road 1 ride height achieved • off road 2 ride height achieved • entry/exit ride height achieved • selected ride height not permitted • service air suspension system immediately • reduce speed to ma...

  • Page 324

    • stop/start not ready extreme outside temperature – if equipped • stop/start not ready engine temperature too high – if equipped • stop/start not ready engine temperature too low – if equipped • stop/start not ready driver seatbelt unbuckled – if equipped • stop/start not ready driver door open – i...

  • Page 325

    • stop/start to restart shift out of park – if equipped • stop/start off – if equipped • autostop duration – if equipped the reconfigurable telltales section is divided into the white telltales area on the right, amber telltales in the middle, and red telltales on the left. Evic selectable menu item...

  • Page 326

    Tire pressure monitoring system (1500 & 2500 series) press and release the up or down arrow button until “tire pressure” is highlighted in the evic. Press and release the select/right arrow button and one of the following will be displayed: a vehicle icon is displayed with tire pressure values in ea...

  • Page 327

    Hold the select/right arrow button to reset all the information. Trip b press and release up & down arrow button until the trip b icon is highlighted in the evic. The trip b information will display the following: • distance • average fuel economy • average speed • elapsed time hold the select/right...

  • Page 328

    Trailer tow press and release the up or down arrow button until the trailer tow icon is highlighted. Press the select/right arrow button and the next screen will display the following trailer trip information: • trailer trip • trailer brake audio press and release the up or down arrow button until t...

  • Page 329

    Personal settings (customer-programmable features) for vehicles equipped a 3.5” evic screen personal settings allows the driver to set and recall features when the transmission is in park. Press and release the up and down button until per- sonal settings displays in the evic. Press and release the ...

  • Page 330

    Units press and release the up or down button until “units” displays in the evic and press the select button. The evic, odometer, and navigation system (if equipped) can be changed between english and metric units of mea- sure. To make your selection, press and release the select button the selected...

  • Page 331

    Button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Auto wipers — if equipped when on is selected, the system will automatically activate the windshield wipers if it senses moisture on the w...

  • Page 332

    Highlighted, then press and release the select button until a check-mark appears next to the setting, showing that the setting has been selected. Headlamps with wipers when this feature is selected and the headlight switch is in the auto position, the headlights will turn on approximately 10 seconds...

  • Page 333

    Select button until a check-mark appears next to the feature showing the system has been activated, or the check-mark is removed showing the system has been deactivated. Auto unlock doors when this feature is selected, all doors will unlock when the vehicle is stopped and the transmission is in the ...

  • Page 334

    When unlock all doors on 1st press is selected, all of the doors will unlock on the first press of the rke transmitter unlock button. To make your selection, scroll up or down until the preferred setting is high- lighted, then press and release the select button until a check-mark appears next to th...

  • Page 335

    A check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Key-off power delay when this feature is selected, the power window switches, radio, hands-free system (if equipped), dvd video system (if equipped), p...

  • Page 336

    Transport mode – if equipped when this feature is selected the air suspension system is disabled to assist with flat bed towing. To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated or the check-mark is remov...

  • Page 337

    Release the select button until a check-mark appears next to the setting, showing that the setting has been selected. Trailer brake type when this feature is selected, the trailer brake type can be changed between “light electric”, “heavy electric”, “light eoh” and “heavy eoh”. To make your selectio...

  • Page 338

    • outside temp (default setting) • trans temp • oil temp • time • range to empty (rte) • average mpg • current mpg • trip a • trip b • trailer trip (distance only) • trailer brake gain upper right • none • compass (default setting) • outside temp • trans temp • oil temp • time • range to empty (rte)...

  • Page 339

    Lower left • none (default setting) • compass • outside temp • trans temp • oil temp • time • range • avg mpg • current mpg • trailer brake gain lower right • none (default setting) • compass • outside temp • trans temp • oil temp • time • range • avg mpg • current mpg • trailer brake gain restore t...

  • Page 340

    Uconnect® settings the uconnect® system uses a combination of soft and hard keys located on the center of the instrument panel that allows you to access and change the customer programmable features. Hard-keys hard-keys are located below the uconnect® system in the center of the instrument panel. In...

  • Page 341

    Comfort & remote start, engine off operation, compass settings, audio, phone/bluetooth® and siriusxm setup. Note: only one touchscreen area may be selected at a time. When making a selection, touch the soft-key to enter the desired mode. Once in the desired mode, touch and release the preferred sett...

  • Page 342

    • set language when in this display, you may select one of three languages for all display nomenclature, including the trip functions and the navigation system (if equipped). Touch the “set language” soft-key and then touch the desired language soft-key until a check-mark appears next to the languag...

  • Page 343

    Designated turn within a programmed route. To make your selection, touch the “navigation turn-by-turn in cluster” soft-key, until a check-mark appears next to the setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. • fuel saver display in cl...

  • Page 344

    • set time minutes when in this display, you may adjust the minutes. The “sync with gps time” soft-key must be unchecked. To make your selection, touch the “+” or “–” soft-keys to adjust the minutes up or down. Touch the back arrow soft-key to return to the previous menu or touch the “x” soft-key to...

  • Page 345

    Reverse. To make your selection, touch the “tilt mir- rors in reverse” soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. • parkview® backup camera your vehicle may be equipped with the parkview®...

  • Page 346

    Gridlines” soft-key, until a check-mark appears next to the setting, indicating that the setting had been selected. Touch the back arrow soft-key to return to the previous menu. • parkview® backup camera fixed guidelines your vehicle may be equipped with the parkview® rear back up camera fixed guide...

  • Page 347

    • parksense® front park assist chime volume front park assist chime volume settings can be selected from the evic or uconnect® system (if equipped). The chime volume settings include low, medium, and high. The factory default volume setting is medium. Refer to “evic settings” or “uconnect® settings”...

  • Page 348

    • four corner air suspension modes — if equipped there are four air suspension modes designed to protect the system in unique situations. Tire jack mode is se- lected to assist in changing a spare tire. Transport mode is selected to assist when the vehicle is being flat bed towed. Wheel alignment mo...

  • Page 349

    Turned off if they were turned on by this feature. To make your selection, touch the headlights with wipers soft- key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. • auto dim high beam — if equipped ...

  • Page 350

    Doors & locks after pressing the doors & locks soft-key the following settings will be available: • auto lock when this feature is selected, all doors will lock auto- matically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, touch the auto lock soft-key, until a check-m...

  • Page 351

    • sound horn with remote start when this feature is selected, the horn will sound when the remote start is activated. To make your selection, touch the sound horn with remote start soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft...

  • Page 352

    Return to the previous menu. Refer to “keyless enter-n- go™” in “things to know before starting your vehicle”. • memory to fob — if equipped this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection, touch the mem...

  • Page 353

    Temperatures are below 40° f (4.4° c). When tempera- tures are above 80° f (26.7° c), the driver vented seat will turn on. To make your selection, press the “auto heated seats” button on the touchscreen, until a check-mark appears next to the setting, showing that the setting has been selected. Pres...

  • Page 354

    Compass settings — if equipped after pressing the “compass settings” soft-key the fol- lowing settings will be available: • variance compass variance is the difference between magnetic north and geographic north. To compensate for the differences the variance should be set for the zone where the veh...

  • Page 355

    Also calibrate the compass by pressing the “on” soft-key and completing one or more 360-degree turns (in an area free from large metal or metallic objects) until the cal indicator displayed in the evic turns off. The compass will now function normally. Audio after pressing the “audio” soft-key the f...

  • Page 356

    To make your selection, touch the “aux volume match” soft-key, select on or off followed by pressing the back arrow soft-key. • loudness — if equipped the radio automatically turns on when vehicle is in run or will recall whether it was on or off at last ignition off. To make your selection, touch t...

  • Page 357

    Press and release the select button until a check-mark appears next to the setting, showing that the setting has been selected. Phone/bluetooth® after touching the “phone/bluetooth®” soft-key the following settings will be available: • paired devices this feature shows which phones are paired to the...

  • Page 358

    • suspension display messages when all is selected, all the air suspension alerts will be displayed. When warnings only is selected only the air suspension warnings will be displayed. • automatic aero mode (1500 model only) when this feature is selected the ride height will auto- matically be adjust...

  • Page 359

    Siriusxm setup after pressing the “sirius” setup soft-key the following settings will be available: • channel skip siriusxm can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scanning. To make your selection, touch the...

  • Page 360

    Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versions may not fully support the ipod® control features. Please visit apple’s website for software updates. For further information, refer to the uconnect® supple- ment manual. Steering wheel audio cont...

  • Page 361

    The button located in the center of the right hand control will switch modes to radio, cd or other valid audio sources. The left hand control is a rocker type switch with a pushbutton in the center. The function of the left hand control is different depending on which mode you are in. The following ...

  • Page 362

    3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become ...

  • Page 363

    Manual climate controls without touchscreen — if equipped the controls for the manual heating and air conditioning system in this vehicle consist of a series of outer rotary dials and inner push knobs. These comfort controls can be set to obtain desired interior conditions. 1 — front blower 5 — max ...

  • Page 364

    Front blower control there are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position. Note: for vehicles equipped with remote start, the climate controls ...

  • Page 365

    Air conditioning operation push the a/c button to engage the air conditioning (a/c). A led will illu- minate when the a/c system is engaged. Max a/c for maximum cooling, when max a/c is selected the a/c is turned on automatically and the air is recirculated. Note: a/c cannot be deselected when in ma...

  • Page 366

    Panel mode air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Bi-level mode air is directed through the panel and floor outlets. Note: there is a difference in temperature (in any conditions other than full cold or full hot), between the u...

  • Page 367

    Defrost mode air is directed through the windshield and side window demist outlets. Use the defrost mode with maximum blower and warm temperature settings for best windshield and side window defrosting. Note: the air conditioning compressor operates in mix and defrost, or a blend of these modes even...

  • Page 368

    • the a/c can be deselected manually without disturb- ing the mode control selection by pressing the a/c button. Air outlets the airflow from each of the instrument panel outlets can be adjusted for direction, and turned on or off to control airflow. Note: for maximum airflow to the rear, the center...

  • Page 369

    Manual climate controls with touchscreen — if equipped hard-keys the hard-keys are located below the radio touchscreen. Soft-keys soft-keys are accessible on the radio touchscreen. Climate controls — hard-keys temperature controls — soft-keys 4 understanding your instrument panel 367.

  • Page 370

    Button descriptions (applies to both hard-keys and soft-keys) 1. Max a/c button press and release to toggle between max a/c and the prior settings. The soft-key illuminates when max a/c is on. In max a/c, the blower level and mode position can be adjusted to desired user settings. Pressing other set...

  • Page 371

    Equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 10 minutes. Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abra...

  • Page 372

    Note: bi-level mode is designed under comfort con- ditions to provide cooler air out of the panel outlets and warmer air from the floor outlets. • floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. • mix mode air come...

  • Page 373

    8. Climate control off button press and release this button to turn the climate control on/off. 9. Temperature control down button push the button for cooler temperature settings. On the touchscreen, slide the temperature bar towards the blue arrow soft-key for cooler temperature settings. 10. Tempe...

  • Page 374

    Automatic climate controls with touchscreen — if equipped hard-keys the hard-keys are located below the uconnect® screen. Soft-keys soft-keys are accessible on the uconnect® system screen. Automatic climate controls — hard-keys uconnect® 5.0 automatic temperature controls — soft-keys 372 understandi...

  • Page 375

    Button descriptions (applies to both hard-keys and soft-keys) 1. Max a/c button press and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manual mode and the max a/c indicator will tur...

  • Page 376

    5. Front defrost button press and release to change the current airflow setting to defrost mode. The indicator illuminates when this fea- ture is on. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level will increase. Use defrost mode wi...

  • Page 377

    7. Passenger temperature control up button provides the passenger with independent temperature control. Push the hard-key button for warmer tempera- ture settings or on the touchscreen, press and slide the soft-key temperature bar towards the red arrow soft-key for warmer temperature settings. Note:...

  • Page 378

    Soft-key use the small blower icon to reduce the blower setting and the large blower icon to increase the blower setting. Blower can also be selected by pressing the blower bar area between the icons. 11. Modes the airflow distribution mode can be adjusted so air comes from the instrument panel outl...

  • Page 379

    • mix mode air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. 12. Climate control off button press and release this button to turn the climate control on/off. 13. Driver temperature control down button provides the driver with independ...

  • Page 380

    Automatic operation 1. Press the auto hard-key or soft-key button on the automatic temperature control (atc) panel. 2. Next, adjust the temperature you would like the system to maintain by adjusting the driver and pas- senger temperature hard or soft control buttons. Once the desired temperature is ...

  • Page 381

    Hard key a second time to turn off the recirculation mode led and allow outside air into the vehicle. Note: in cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (soft-key button greyed out) if conditions exist that could create...

  • Page 382

    Adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window fogging and frosting vehicle windows tend to fog on the inside of the glass in mild, rainy and/or humid weather. Windows may frost on the inside of the glass in very cold weather. To...

  • Page 383

    Operating tips chart 4 understanding your instrument panel 381.

  • Page 385: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .390 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .390 ▫ automatic transmission . . . . . . . . . . . . . . . .391 ▫ keyless enter-n-go™ . . . . . . . . . . . . . . . . . .391 ▫ normal starting. . . ....

  • Page 386

    ▫ brake/transmission shift interlock system . . .403 ▫ eight-speed automatic transmission — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .403 ▫ six-speed automatic transmission — 1500 models only (if equipped) . . . . . . . . . . . . . . . . . . . .412 ▫ six-speed automatic transm...

  • Page 387

    ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .469 䡵 axle locker system — power wagon models only (if equipped) . . . . . . . . . . . .469 䡵 stabilizer/sway bar system — power wagon only . . . . . . . . . . . . . . . . . . . . . . . .472 䡵 safe off-road driving — power wagon only ....

  • Page 388

    ▫ things to know before using your winch. . . .498 ▫ understanding the features of your winch. . .501 ▫ winch accessories . . . . . . . . . . . . . . . . . . . .503 ▫ operating your winch . . . . . . . . . . . . . . . . . .504 ▫ rigging techniques . . . . . . . . . . . . . . . . . . . .516 䡵 power s...

  • Page 389

    ▫ tire identification number (tin). . . . . . . . . . .542 ▫ tire terminology and definitions . . . . . . . . . .544 ▫ tire loading and tire pressure . . . . . . . . . . .545 䡵 tires — general information . . . . . . . .550 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .550 ▫ tire in...

  • Page 390

    䡵 fuel requirements . . . . . . . . . . . . . . . . . .577 ▫ 3.6l/6.4l engine . . . . . . . . . . . . . . . . . . . . . .577 ▫ 5.7l engines . . . . . . . . . . . . . . . . . . . . . . . . .577 ▫ reformulated gasoline . . . . . . . . . . . . . . . . .578 ▫ gasoline/oxygenate blends . . . . . . . . . ...

  • Page 391

    ▫ common towing definitions . . . . . . . . . . . . .591 ▫ trailer hitch type and maximum trailer weight . . . . . . . . . . . . . . . . . . . . . . .594 ▫ trailer towing weights (maximum trailer weight ratings) . . . . . . . . . . . . . . . . . . . . . .595 ▫ trailer and tongue weight . . . . . . ....

  • Page 392

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Warnin...

  • Page 393

    Automatic transmission start the engine with the shift lever in the neutral or park. Apply the brake before shifting into any driving range. Note: this vehicle is equipped with a transmission shift interlocking system. The brake pedal must be pressed to shift out of park. Tip start feature do not pr...

  • Page 394

    4. If you wish to stop the cranking of the engine prior to the engine starting, press the button again. Note: normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. To turn off the engine using engine start/stop button 1. Place the shift leve...

  • Page 395

    Engine start/stop button functions — with driver’s foot off the brake pedal (in park or neutral position) the engine start/stop button operates similar to an ignition switch. It has three positions, off, acc, run. To change the ignition switch positions without starting the vehicle and use the acces...

  • Page 396

    Warning! • never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic tr...

  • Page 397

    Stop/start system — if equipped the stop/start function is developed to save fuel and reduce emissions. The system will stop the engine auto- matically during a vehicle stop if the required conditions are met. Releasing the brake pedal will automatically re-start the vehicle. Automatic mode the stop...

  • Page 398

    Possible reasons the engine does not auto stop prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled. In following situations the engine will not stop: • driver’s seat belt is not buckled • driver’s door is not closed • outside temperature i...

  • Page 399

    Restart. During this transition the brakes will hold the vehicle to avoid undesired vehicle movement. Conditions that will cause the engine to start automati- cally while in autostop mode. The engine will start automatically when: • the transmission selector is moved from drive to reverse or neutral...

  • Page 400

    Park message, or a stop/start key start re- quired message, to indicate which action is required. Refer to “electronic vehicle information center (evic)” in “understanding your instrument panel” for further information. To manually turn off the stop start system 1. Press the stop/start off switch (l...

  • Page 401

    3. At the next vehicle stop (after turning off the stop/ start system) the engine will not be stopped. 4. If the stop/start system is manually turned off, the engine can only be started and stopped by cycling the ignition switch. 5. The stop/start system will reset itself back to an on condition eve...

  • Page 402

    1500 models the engine block heater cord is routed under the hood on the passenger side of the vehicle near the right head lamp assembly. It is located between the front grill and the radiator, but underneath the black upper seal. 2500/3500 models the engine block heater cord is routed through the g...

  • Page 403

    Caution! (continued) • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting into any gear, make sure your foot is firmly pressing the brake pedal. Note: you must press and hold the brake pedal while shifting out of park. Warning! • it is dang...

  • Page 404

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 405

    Before the ignition switch can be turned to the full off (key removal) position. The key fob can only be re- moved from the ignition when the ignition is in the full off position, and the transmission is locked in park whenever the ignition switch is in the full off position. Note: if a malfunction ...

  • Page 406

    The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilomete...

  • Page 407

    Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to...

  • Page 408

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 409

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 410

    Neutral (n) use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift the transmission into park if you must leave the vehicle. Warning! Do not coast in neutral and never turn off the ignition...

  • Page 411

    (ers) operation ⬙ in this section) to select a lower gear range. Under these conditions, using a lower gear range will improve performance and extend transmission life by reducing excessive shifting and heat buildup. During extremely cold temperatures (-22°f [-30°c] or below), transmission operation...

  • Page 412

    4. Wait approximately 30 seconds. 5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest po...

  • Page 413

    To exit ers mode, simply press and hold the gear+ switch until “d” is once again displayed in the instru- ment cluster. Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal in...

  • Page 414

    The “tow/haul indicator light” will illuminate in the instrument cluster to indicate that tow/haul mode has been activated. Pressing the switch a second time restores normal operation. Normal operation is always the default at engine start-up. If tow/haul mode is desired, the switch must be pressed ...

  • Page 415

    The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilomete...

  • Page 416

    When parking on a level surface, you may shift the transmission into park first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting the transmission to park, otherwise the load on the transmission locking mechanism may make it diffi- cult to move the sh...

  • Page 417

    Warning! (continued) • unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and ...

  • Page 418

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the off posi- tion to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ran...

  • Page 419

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 420

    Range will improve performance and extend transmission life by reducing excessive shifting and heat buildup. If the transmission temperature exceeds normal operat- ing limits, the powertrain controller will modify the transmission shift schedule and expand the range of torque converter clutch engage...

  • Page 421

    Direct gears only. Normal operation will resume once the transmission temperature has risen to a suitable level. Transmission limp home mode transmission function is monitored electronically for abnormal conditions. If a condition is detected that could result in transmission damage, transmission li...

  • Page 422

    If the transmission cannot be reset, authorized dealer service is required. Electronic range select (ers) operation — six-speed transmission the electronic range select (ers) shift control allows the driver to limit the highest available gear when the shift lever is in the drive position. For exampl...

  • Page 423

    To exit ers mode, simply press and hold the shift lever to the right (+) (console shift) or press the ers (+) switch (column shift) until “d” is once again displayed in the instrument cluster. Column shift lever console shift lever 5 starting and operating 421.

  • Page 424

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Note: to select the proper gear position for maximum deceleration (engine braking), simply press and hold the shif...

  • Page 425

    When to use tow/haul mode when driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the tow/haul switch to activate tow/ haul mode. This will improve performance and reduce the potential for transmission overheating or failure due ...

  • Page 426

    Warning! Do not use the “tow/haul” feature when driving in icy or slippery conditions. The increased engine braking can cause the rear wheels to slide, and the vehicle to swing around with the possible loss of vehicle control, which may cause an accident possi- bly resulting in personal injury or de...

  • Page 427

    Cause damage to the transmission. The torque con- verter will refill within five seconds after starting the engine. Six-speed automatic transmission — 2500/3500 models only the transmission gear position display (located in the instrument cluster) indicates the transmission gear range. The shift lev...

  • Page 428

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 429

    Warning! (continued) • your vehicle could move and injure you and others if it is not completely in park. Check by trying to move the shift lever out of park with the brake pedal released. Make sure the transmission is in park before leaving the vehicle. • it is dangerous to shift out of park or neu...

  • Page 430

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 431

    • release the shift lever and make sure it is fully seated in the park gate. • look at the transmission gear position display and verify that it indicates the park position. • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the v...

  • Page 432

    Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through underdrive first, second, and third gears, direct fourth gear and overdrive fifth and sixth gears. Th...

  • Page 433

    During cold temperatures, transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed. This feature im- proves warm up time of the engine and transmission to achieve maximum efficiency. Engagement of both the torque converter clutch and the top ov...

  • Page 434

    Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required...

  • Page 435

    To exit ers mode, simply press and hold the ers (+) switch until “d” is once again displayed in the instru- ment cluster. Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal ...

  • Page 436

    • vehicle speed is sufficiently high. • the tow/haul switch has not been activated. When to use tow/haul mode when driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the tow/haul switch to activate tow/ haul mode. This will impro...

  • Page 437

    Warning! Do not use the “tow/haul” feature when driving in icy or slippery conditions. The increased engine braking can cause the rear wheels to slide, and the vehicle to swing around with the possible loss of vehicle control, which may cause an accident possi- bly resulting in personal injury or de...

  • Page 438

    Cause damage to the transmission. The torque con- verter will refill within five seconds after starting the engine. Four-wheel drive operation — if equipped four-wheel drive trucks are equipped with either a manually shifted transfer case or an electronically shifted transfer case. Refer to the oper...

  • Page 439

    The transfer case is shifted into either the 4h or 4l position. There is no light for the 2h or neutral positions on some models. When operating your vehicle in 4l, the engine speed is approximately three times that of the 2h or 4h positions at a given road speed. Take care not to overspeed the engi...

  • Page 440

    For additional information on the appropriate use of each transfer case mode position, see the information below: 2h rear-wheel drive high range — this range is for normal street and highway driving on dry hard surfaced roads. 4h four-wheel drive high range — this range locks the front and rear driv...

  • Page 441

    Vehicle in motion, the transfer case will engage/ disengage faster if you momentarily release the accelera- tor pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 2h or 4h to 4l with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift the transmission ...

  • Page 442

    Electronically shifted transfer case (four-position switch) — if equipped this is an electronic shift transfer case and is operated by the 4wd control switch (transfer case switch), which is located on the instrument panel. This electronically shifted transfer case provides four mode positions: • tw...

  • Page 443

    And 4wd low positions are designed for loose, slippery road surfaces only. Driving in the 4wd lock and 4wd low positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline compo- nents. Note: the transfer case neutral position is selected by pressing the button loca...

  • Page 444

    Note: before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met. To retry the selection, turn the control knob back to the current position, wait five seconds, and retry selection. To find the shift require- ments, refer to...

  • Page 445

    Warning! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the neutral position without first fully engaging the parking brake. The transfer case neutral position disengages both the front and rear drive shafts from the powertrain and will allow t...

  • Page 446

    4wd low four-wheel drive low range — this range provides low speed four-wheel drive. It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed. This range provides additional traction and maximum pulling power for loose, slippery road surfaces only. D...

  • Page 447

    2wd to 4wd lock rotate the 4wd control switch to the desired position. Shifts between 2wd and 4wd lock can be done with the vehicle stopped or in motion. With the vehicle in motion, the transfer case will engage/disengage faster if you momentarily release the accelerator pedal after turn- ing the co...

  • Page 448

    Alternate procedure 1. Bring the vehicle to a complete stop. 2. With the ignition switch in the on position and the engine running, shift the transmission into neutral. 3. Rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is on (not flashi...

  • Page 449

    Electronically shifted transfer case (five-position switch) — if equipped this is an electronic shift transfer case and is operated by the 4wd control switch (transfer case switch), which is located on the instrument panel. This electronically shifted transfer case provides five mode positions: • tw...

  • Page 450

    For variable driving conditions, the 4wd auto mode can be used. In this mode, the front axle is engaged, but the vehicle’s power is sent to the rear wheels. Four - wheel drive will be automatically engaged when the vehicle senses a loss of traction. Because the front axle is engaged, this mode will ...

  • Page 451

    3. When the shift is complete, the indicator light for the selected position will stop flashing and remain on. If one or more shift conditions are not met: 1. The indicator light for the current position will remain on. 2. The newly selected position indicator light will con- tinue to flash. 3. The ...

  • Page 452

    Auto or 4wd lock positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the drivetra...

  • Page 453

    4wd lock four-wheel drive lock range - this range maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. 4wd low four - wheel drive low range - this range provides low speed four-wheel drive...

  • Page 454

    • if all the requirements to select a new transfer case position have been met, the current position indicator light will turn off, the selected position indicator light will flash until the transfer case completes the shift. When the shift is complete, the position indicator light for the selected ...

  • Page 455

    • four-wheel drive low range (4wd low) • neutral (neutral) this electronically shifted transfer case is designed to be driven in the two–wheel drive position (2wd) or four- wheel drive position (4wd auto) for normal street and highway conditions on dry hard surfaced roads). Driving the vehicle in 2w...

  • Page 456

    Transfer case position indicator lights the transfer case position indicator lights (4wd, 4low, and 4wd auto) are located in the instrument cluster and indicate the current and desired transfer case selection. When you select a different transfer case posi- tion, the indicator lights will do the fol...

  • Page 457

    Means that the four-wheel drive system is not function- ing properly and that service is required. Warning! Always engage the parking brake when powering down the vehicle if the “svc 4wd warning light” is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause perso...

  • Page 458

    For additional information on the appropriate use of each transfer case mode position, see the information below: 2wd rear-wheel drive high range - this range is for normal street and highway driving on dry hard surfaced roads. 4wd auto four-wheel drive auto range - this range sends power to the rea...

  • Page 459

    Shifting procedure note: • if any of the requirements to select a new transfer case position have not been met, the transfer case will not shift. The position indicator light for the previous position will remain on and the newly selected posi- tion indicator light will continue to flash until all t...

  • Page 460

    Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) or completely stopped. Use either of the following procedures: preferred procedure 1. With the engine running, slow the vehicle to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into neutral. 3. While still rolling, pre...

  • Page 461

    Air suspension system (1500 models only) — if equipped description the air suspension system provides full time load level- ing capability along with the benefit of being able to adjust vehicle height by the push of a button. 1 — up button 2 — down button 3 — entry/exit mode indicator lamp (customer...

  • Page 462

    Note: the vehicle will automatically enter aero mode when the vehicle speed remains between 62 mph (100 km/h) and 66 mph (106 km/h) for greater than 20 seconds or if the vehicle speed exceeds 66 mph (106 km/h). • normal ride height (nrh) – this is the standard position of the suspension and is meant...

  • Page 463

    • if the vehicle is in offroad1 or offroad2 setting, be aware of your surroundings, you may not have the clearance required for certain areas and vehicle dam- age may occur. • aero mode (lowers the vehicle approximately .6 in [15 mm]) – this position provides improved aerody- namics by lowering the ...

  • Page 464

    15 mph (24 km/h). Entry/exit mode may not be available due to vehicle payload, an evic message will be displayed when this occurs. Refer to ⬙electronic vehicle information center (evic) ⬙ in ⬙understanding your instrument panel ⬙ for further information. Note: entry/exit mode may be achieved using y...

  • Page 465

    Warning! The air suspension system uses a high pressure volume of air to operate the system. To avoid per- sonal injury or damage to the system, see your authorized dealer for service. Air suspension modes the air suspension system has multiple modes to protect the system in unique situations: tire/...

  • Page 466

    Protection mode in order to “protect” the air suspension system, the vehicle will enter protection mode when load leveling cannot be achieved. Some driving may be required to clear the protection mode telltale in the evic. Refer to “electronic vehicle information center (evic)” in “un- derstanding y...

  • Page 467

    Pressing the “up” button once will move the suspension one position higher from the current position, assuming all conditions are met (i.E. Key in on/run position, engine running, speed below threshold, etc). The “up” button can be pressed multiple times, each press will raise the requested level by...

  • Page 468

    • transport mode – no indicator lamps will be illumi- nated. Transport mode is disabled by driving the vehicle. • tire/jack mode – indicator lamps 3 and 6 will be illuminated. Tire/jack mode is disabled by driving the vehicle. • wheel alignment mode – indicator lamps 3 and 4 will be illuminated. Whe...

  • Page 469

    Trailer mode (lowers the vehicle approximately 1 in (25 mm) – this position will lower the rear suspension and provide load leveling for all loading conditions including towing a trailer. The trailer button will blink continu- ously until trailer height has been achieved. The system requires that th...

  • Page 470

    Note: this mode is intended to be enabled with engine running. Transport mode to assist with flat bed towing, the air suspension system has a feature which will put the vehicle below normal ride height (nrh) and disable the automatic load leveling system. This mode is intended to be used with engine...

  • Page 471

    Electronic vehicle information center (evic) display messages when the appropriate conditions exist, a message will appear in the evic display. Refer to “electronic vehicle information center (evic)” in “understanding your instrument panel” for further information. An audible chime will be heard whe...

  • Page 472

    Stuck. The locking front and rear differentials should only be engaged during low-speed, extreme off-road situa- tions where one wheel is likely to not be in contact with the ground. It is not recommended to drive the vehicle with the differentials locked on pavement due to the reduced ability to tu...

  • Page 473

    To lock the rear axle, place the vehicle in 4lo. Refer to “four wheel drive operation” in “starting and operat- ing” for further information. Move the axle locker switch position to rear lock while traveling less than 3 mph (5 km/h). The rr indicator light will remain on when the rear axle is locked...

  • Page 474

    Note: the axle lockers could be torque locked due to side to side loads on the axle. Driving slowly while turning the steering wheel from a left hand turn to a right hand turn or driving in reverse for a short distance may be required to release the torque lock and unlock the axles. To unlock the re...

  • Page 475

    The switch has two positions; on-road and off-road. The system is normally in the on-road mode, indicated by a solid green light. The stabilizer/sway bar should remain in the on-road mode during normal driving conditions. Warning! Do not disconnect the stabilizer bar and drive on hard surfaced roads...

  • Page 476

    Warning! If the stabilizer/sway bar will not return to on-road mode, vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury or death. Contact ...

  • Page 477

    Ramp travel index (rti) the ramp travel index is the distance, in inches, that you can drive your vehicle with one wheel on a 20-degree ramp without lifting any other wheel off the ground. This distance up the ramp divided by the wheelbase of the vehicle and multiplied by 1,000 is the rti. This vehi...

  • Page 478

    Mud, snow and ice. Every surface has a different effect on your vehicle’s steering, handling and traction. Control- ling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture. Avoid sudden accelerations, t...

  • Page 479

    Driving in snow, mud and sand there is a drastic reduction in traction when driving in snow, mud or sand. The vehicle will be less responsive to steering, acceleration and braking inputs. Therefore you should accelerate slowly, leave greater stopping distances and avoid abrupt vehicle maneuvers. You...

  • Page 480

    • sand – soft sand is very difficult to travel through with full tire pressure. When crossing soft sandy spots in a trail maintain your vehicle’s momentum and do not stop. The key to driving in soft sand using the appro- priate tire pressure, accelerating slowly, avoiding abrupt maneuvers and mainta...

  • Page 481

    Throttle lightly while holding a light brake pressure and ease the vehicle up and over the object. Warning! Crossing obstacles can cause abrupt steering system loading which could cause you to loose control of your vehicle. Using a spotter there are many times where it is hard to see the obstacle or...

  • Page 482

    Vehicle’s mobility. Approach these obstacles at a 45- degree angle and let each tire go through the obstacle independently. You need to use caution when crossing large obstacles with steep sides. Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle ...

  • Page 483

    What is the best direction to recover the vehicle. Depend- ing on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down. You can also try rocking the vehicle or winching the vehicle off the object....

  • Page 484

    Apply more power as you start up the hill. Do not race forward into a steep grade, the abrupt change of grade could cause you to lose control. If the front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground. As you approach the crest of the hill ease off ...

  • Page 485

    Warning! Do not descend a steep grade in neutral. Use vehicle brakes in conjunction with engine braking. Descending a grade too fast could cause you to lose control and be seriously injured or killed. • driving across an incline – if at all possible avoid driving across an incline. If it is necessar...

  • Page 486

    Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle, which may result in severe injury. Always back carefully straight down a hill in reverse. Never back down a h...

  • Page 487

    Caution! Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components and your brakes will be less effective once wet and/or mudd...

  • Page 488

    Caution! Muddy waters can reduce the cooling system effec- tiveness by depositing debris onto the radiator. • crossing ditches, streams, shallow rivers or other flowing water – flowing water can be extremely dangerous. Never attempt to cross a fast running stream or river even in shallow water. Fast...

  • Page 489

    Airing down for off-road driving running lower tire pressure off-road can improve your ride comfort and vehicle traction. Reducing the tire air pressure allows the tire to bulge slightly, improving its surface area for better flotation and ability to mold or form to the ground contour. Different ter...

  • Page 490

    Vehicle? Is there an anchor point to winch to? Are you alone or do you have another vehicle to help? Is there high risk of vehicle damage during the recovery process? Answering these questions will help you determine the best method of recovery. If you can still move the vehicle slightly and the onl...

  • Page 491

    Shift. If after a few rock cycles your vehicle is not free, stop and try another method of recovery. Continuous rock cycling will only cause unnecessary damage to your vehicle and the environment. Caution! Damage can occur when spinning your tires at an excessive high speed. Do not spin your tires f...

  • Page 492

    Brakes, once signaled by the other driver. This se- quence is important to avoid having the recovered vehicle hit the pulling vehicle. Warning! Never use tow straps with end hooks or link two straps with a clevis pin. These heavy metal objects could become projectiles if a strap breaks, which could ...

  • Page 493

    Floor mat or something else over the strung out cable. Placing something over the strung out cable helps keep the cable on the ground if it breaks. Next, place the vehicle in first gear and apply a very light throttle as you power the winch in. Be careful not to allow slack in the cable as you recov...

  • Page 494

    • check for accumulations of plants or brush. These things could be a fire hazard. They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts. • after extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, br...

  • Page 495

    Will supply maximum traction. When starting with only one rear wheel on an excessively slippery surface, slight momentary application of the parking brake may be necessary to gain maximum traction. Warning! On vehicles equipped with a limited-slip differential never run the engine with one rear whee...

  • Page 496

    Traction when driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precau- tions shoul...

  • Page 497

    Warning! (continued) your vehicle away swiftly. Failure to follow this warning may result in injuries that are serious or fatal to you, your passengers, and others around you. Shallow standing water although your vehicle is capable of driving through shallow standing water, consider the following ca...

  • Page 498

    Caution! (continued) • determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects. • driving through stand...

  • Page 499

    When driving over sand, mud, and other soft terrain, shift to low gear and drive steadily. Apply the accelerator slowly to avoid spinning the wheels. Do not reduce the tire pressures for this type of driving. After driving off-road off-road operation puts more stress on your vehicle than does most o...

  • Page 500

    Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent a collision. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if y...

  • Page 501

    Tensioning the wire rope the winch rope must be properly tensioned before use. Follow the instructions below to tension the rope: 1. Un-spool the wire rope leaving five wraps of rope on the winch drum. 2. Attach the hook to a suitable anchor point. Caution! Be certain the anchor will withstand the l...

  • Page 502

    Winch motor thermal protection your winch is equipped with a thermal protection device in the motor. If the winch is operated for an excessive duration, the device may interrupt motor function to protect the winch motor. During this time the winch will power-out but will not power-in. Allow the winc...

  • Page 503

    Understanding the features of your winch winch components 5 starting and operating 501.

  • Page 504

    1. Motor: the winch motor is powered by the vehicle charging system and features a thermal protection switch that automatically stops motor function in the power-in direction if the motor gets too hot. 2. Remote socket: the remote socket allows the remote control to be attached to the control pack t...

  • Page 505

    Winch accessories the following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: wire rope, through use, will develop ⬙barbs⬙ which can slice skin. It is ex- tremely important to wear pro- tective gloves while operating the winch or h...

  • Page 506

    Clevis/d-shackles: the d-shackle is a safe means of connecting the looped ends of cables, straps and snatch blocks. The shackle’s pin is threaded to allow easy re- moval. Tree trunk protector: typi- cally made of tough, high- quality nylon, it provides the operator an attachment point for the winch ...

  • Page 507

    Warning! (continued) • always stand clear of wire rope and load and keep others away during winching. • always keep hands and clothing clear of the wire rope, hook and fairlead opening during operation and when spooling. • never wrap wire rope back onto itself. Always use a choker chain, wire choker...

  • Page 508

    3. Use the right equipment for the situation. 4. Always wear leather gloves and do not allow the wire rope to slip through your hands when handling the rope. 5. Only the operator should handle the wire rope and remote control. 6. Think safety at all times. Vehicle recovery using the winch caution! •...

  • Page 509

    1. Inspect the winch, winch mount, and wire rope for damage. Do not use the winch if the mount is loose or rope shows excessive wear or damage. 2. Put on gloves. 3. Disengage the clutch to allow free spooling of the winch drum, rotate the clutch lever on the winch to disengage. Freespooling conserve...

  • Page 510

    5. Pull the wire to the anchor point. Pull out enough wire rope to reach your anchor point. Be sure to keep a certain amount of tension on the wire as it can become twisted and over-wrapped when slackened, leading to wire rope damage. To prevent losing the end, hold the hook strap while you work. 6....

  • Page 511

    Caution! Always be certain the anchor you select will with- stand the load. Note: how to choose an anchor point: a secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural anchors include trees, stumps and rocks. Hook the cable as low as possi...

  • Page 512

    8. Lock the clutch. Lock the winch drum by rotating the clutch lever on the winch to engage. Note: always ensure the clutch is fully engaged or disengaged. 9. Connect the remote control to the winch control box, located behind the front bumper. Be careful not to let the remote control cord dangle in...

  • Page 513

    10. Put wire rope under tension. Using the remote con- trol switch, slowly wind the wire rope until no slack remains. Once the wire rope is under tension, stand well clear of it and never step over it. 11. Check your anchor. Make sure all connections are secured and free of debris before continuing ...

  • Page 514

    In certain situations you may decide to throw a heavy blan- ket or similar object over the wire rope. A heavy blanket can absorb energy should the wire rope break. Place it on the wire rope midway be- tween the winch and the an- chor point. Do this before the wire rope is put under ten- sion. Do not...

  • Page 515

    Behind or in front of the vehicle and never near the wire rope or snatch block. Your situation may have other ⴖno peopleⴖ zones. 14. Begin winching. With the winching vehicles engine on and light tension already on the wire rope, begin winching slowly and steadily. Be sure that the wire rope is wind...

  • Page 516

    Note: • avoid overheating the winch motor. For extended winching, stop at reasonable intervals to allow the winch motor to cool down. • what to look for under load: the wire rope must always spool onto the drum as indicated by the drum rotation decal on the winch. As you power-in, make sure the wire...

  • Page 517

    Warning! To prevent serious injury, never put your fingers inside the hook area as you are powering-in. Note: how to spool under no load: arrange the re- mote control lead so it cannot be caught in the winch. Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope alr...

  • Page 518

    19. Disconnect the remote control. Disconnect the remote control cord from the control box and store in a clean and dry place. Winching operations are now com- plete. Put the cap on the solenoid plug-in. Note: always store the remote control in a protected, clean, dry area. Rigging techniques variou...

  • Page 519

    How to change the pulling direction all winching operations should have a straight line from the winch to the object being pulled. This minimizes the wire rope collecting on one side of the drum affecting pulling efficiency and damaging wire rope. A snatch block, secured to a point directly in front...

  • Page 520

    Double line because pulling power decreases with the number of layers of wire rope on the winch drum, you can use a snatch block to double line out more wire rope. This decreases the number of layers of wire rope on the drum, and increases pulling power. Start by feeding out enough wire rope to free...

  • Page 521

    If the steering icon is flashing, it indicates that the vehicle needs to be taken to the dealer for service. It is likely the vehicle has lost power steering assistance. If the steering icon is displayed and the “power steer- ing system over temp” message is displayed on the evic screen, they indica...

  • Page 522

    If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these condi- tions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. Note: • increased noise levels at the end of ...

  • Page 523

    Caution! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the new vehicle limited warranty. Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from movi...

  • Page 524

    When the parking brake is applied with the ignition switch on, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the transmis- sion is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sou...

  • Page 525

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • never leave children alone in a vehicle, or with access to an unlocked vehicle. Leaving unattended child...

  • Page 526

    Brake system if power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. However, you will experience a substantial increase in braking effort to stop the vehicle. If either the front or rear hydraulic system loses normal bra...

  • Page 527

    The system’s pump motor runs during an abs stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation. This is normal. The abs conducts a low-speed selftest at about 10 mph (16 km/h). If you have your foot lightly on the brake while this test is occurring...

  • Page 528

    Warning! (continued) • the abs cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • the capabilities of an abs-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize th...

  • Page 529

    Anti-lock brake system (abs) the abs aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lockup and help avoid skidding on slippery surfaces during braking. Note: abs improves steering control of the vehicle d...

  • Page 530

    Brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if tcs and esc are in the “partial off” mode. Refer to “electronic stability control (esc)” in this section of this manual. This brake pressure modulation...

  • Page 531

    Warning! (continued) • the capabilities of a bas-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. Hill start assist (hsa) — if equipped the hsa system is designed to assist the driver in launching a vehicle o...

  • Page 532

    Warning! There may be situations on minor hills with a loaded vehicle or while pulling a trailer where the system will not activate and slight rolling may occur, which could cause a collision with another vehicle or object. Always remember the driver is responsible for brak- ing the vehicle. The sys...

  • Page 533

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision w...

  • Page 534

    3. With the engine running and the brake applied, rotate the steering wheel 180° counterclockwise from center. 4. Press the “esc off” switch four times within 20 seconds. The “esc off indicator light” should appear and disappear four times. 5. Rotate the steering wheel 360° clockwise. 6. Cycle ignit...

  • Page 535

    • oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • understeer - when the vehicle is turning less than appropriate for the steering wheel position. Warning! Electronic stability control (esc) cannot prevent the natural laws of physics from acting on the...

  • Page 536

    Esc partial off this mode is entered by momentarily pressing the “esc off” switch. When in ⬙partial off⬙ mode, the tcs portion of esc, except for the “limited slip” feature described in the tcs section, has been disabled and the ⬙esc off indicator light ⬙ will be illuminated. All other stability fea...

  • Page 537

    Warning! • when in “partial off” mode, the tcs functionality of esc, (except for the limited slip feature de- scribed in the tcs section), has been disabled and the “esc off indicator light” will be illuminated. When in “partial off” mode, the engine power reduction feature of tcs is disabled, and t...

  • Page 538

    In this mode, esc and tcs except for the “limited slip” feature described in the tcs section are turned off until the vehicle reaches a speed of 40 mph (64 km/h). At 40 mph (64 km/h) the system returns to “partial off” mode, described above. When the vehicle speed drops below 35 mph (56 km/h) the es...

  • Page 539

    Malfunction has been detected in the esc system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected. T...

  • Page 540

    Trailer sway control (tsc) — if equipped the tsc system uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appro- priate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appropriate wheel(s) to counteract the sw...

  • Page 541

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 542

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 543

    Example: r = construction code – ⬙r⬙ means radial construction – ⬙d⬙ means diagonal or bias construction 15 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of spee...

  • Page 544

    Example: load identification: ⴖ....Blank....ⴖ = absence of any text on the sidewall of the tire indicates a standard load (sl) tire extra load (xl) = extra load (or reinforced) tire light load (ll) = light load tire c, d, e, f, g = load range associated with the maximum load a tire can carry at a sp...

  • Page 545

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 546

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 547

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. B-pillar location for tire and loading information placard 5 starting and operating 545.

  • Page 548

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 549

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this section. To determine the maximum loading conditions of your ...

  • Page 550

    Note: • if your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. The follow- ing table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and num- ber and size of occupan...

  • Page 551

    5 starting and operating 549.

  • Page 552

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 553

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns t...

  • Page 554

    Tire inflation pressures the proper cold tire inflation pressure is listed on the driver’s side b-pillar or rear edge of the driver’s side door. At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining pro...

  • Page 555

    Example: if garage temperature = 68°f (20°c) and the outside temperature = 32°f (0°c) then the cold tire inflation pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12°f (7°c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to...

  • Page 556

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than ¼⬙ (6 mm). Consult an authorized...

  • Page 557

    Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Snow tires some areas of the country require the use of snow tires during the winter. Snow tires can be identified by a mountain/snowflake symbol on the tire sidewall. If you need sn...

  • Page 558

    See the tire pressure monitoring section for more infor- mation. Spare tires — if equipped note: for vehicles equipped with tirefit instead of a spare tire, please refer to “tirefit kit” in “what to do in emergencies” for further information. Caution! Because of the reduced ground clearance, do not ...

  • Page 559

    Since this tire has limited tread life, the original equip- ment tire should be repaired (or replaced) and reinstalled on your vehicle at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically f...

  • Page 560

    Your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than ...

  • Page 561

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 562

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 563

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 564

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage. • traction device must be of proper size for the tire, as recommended by the traction device manufacturer. Please follow the table below for proper ...

  • Page 565

    Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device cleara...

  • Page 566

    Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation are...

  • Page 567

    Directional tires — if equipped for the r/t package with 22” tires and wheels, the rotational direction of the tire must be taken into consid- eration when rotating the tires. The recommended rota- tion pattern for directional tires is shown below. Dual rear wheels — if equipped the tires used on du...

  • Page 568

    Note: if your vehicle is equipped with a tire pressure information system (tpis): • the tire pressure information system (tpis) uses unique sensors in the inner rear wheels to help identify them from the outer rear wheels, because of this, the inner and outer wheel locations can’t be switched. • aft...

  • Page 569

    Tire pressure monitor system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12°f (6.5°c). This means that when the outsi...

  • Page 570

    To be driven for up to 20 minutes above 15 mph (25 km/h) in order for the tpms to receive this informa- tion. For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kpa). If the ambient temperature is 68°f (20°c) and the measured tire...

  • Page 571

    Note: • the tpms is not intended to replace normal tire care and maintenance or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat a...

  • Page 572

    The matching full size spare wheel and tire assembly (if equipped) has a tpm sensor. The matching full size spare can be used in place of any of the four road tires. The tpms will only monitor the pressure in the full size spare when it is used in place of a road tire. Otherwise, a spare with a pres...

  • Page 573

    A system fault can occur due to any of the following: 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accumula...

  • Page 574

    Note: it is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure. The tpms consists of the following components: • receiver module, • four tpm sensors, • various tpms messages, which display in the elec- tronic vehi...

  • Page 575

    Should this occur, you should stop as soon as possible and inflate the tires with a low pressure condition (those flashing or in a different color in the evic graphic) to the vehicle’s recommended cold placard pressure inflation value as shown in the ⬙inflate to xx⬙ message. Once the system receives...

  • Page 576

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” will no longer flash, and the ⬙service tpm system ⬙ message will no longer display, and a pressure value will disp...

  • Page 577

    Vehicles with full size spare 1. The matching full size spare wheel and tire assembly has a tpm sensor that can be monitored by the tpms. 2. If you install the full size spare in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition switch cycle, a chi...

  • Page 578

    The tpis consists of the following components: • receiver module • four tpm sensors (single rear wheel (srw) applica- tions) • six tpm sensors (dual rear wheel (drw) applica- tions) • pressure display in the electronic vehicle information center (evic) the tpis system will display all four (single r...

  • Page 579

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 580

    An octane range of 87 to 89. The manufacturer recom- mends the use of 89 octane for optimum performance. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. Light spark knock at low engine speeds is not harmful to your engine. Ho...

  • Page 581

    Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in starting and drivability prob- lems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the “malfunction indicator l...

  • Page 582

    • change the engine oil and oil filter. • disconnect and reconnect the battery to reset the engine controller memory. More extensive repairs will be required for prolonged exposure to e-85 fuel. Mmt in gasoline methylcyclopentadienyl manganese tricarbonyl (mmt) is a manganese-containing metallic add...

  • Page 583

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition malfu...

  • Page 584

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 585

    E-85 fuel cap e-85 badge 5 starting and operating 583.

  • Page 586

    Ethanol fuel (e-85) e-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Warning! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap)...

  • Page 587

    Caused by these deposits, a supplemental gasoline additive, such as mopar® injector cleanup or techron may be used. Selection of engine oil for flexible fuel vehicles (e-85) and gasoline vehicles ffv vehicles operated on e-85 require specially formu- lated engine oils. These special requirements are...

  • Page 588

    Replacement parts many components in your flexible fuel vehicle (ffv) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol com- patible parts. Caution! Replacing fuel system components with non-ethanol compatible components can damage your veh...

  • Page 589

    Note: when removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler door. Caution! • damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • a poorly fitting gas cap could let impurities into the...

  • Page 590

    • when the fuel nozzle “clicks” or shuts off, the fuel tank is full. Warning! Static electricity can cause an ignition of flammable liquid, vapor or gas in any vehicle or trailer. To reduce risk of serious injury or death when filling containers: • always place container on the ground before fill- i...

  • Page 591

    This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle weight rating (gawr) front and rear, and vehicle identification number (vin). A month-day-hour (mdh) number is included on this label and indicates the month, day and hour of manufacture. The bar co...

  • Page 592

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 593

    Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. Trailer towing in th...

  • Page 594

    Measure gtw is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Gross axle weight rating (gawr...

  • Page 595

    Trailer sway control the trailer sway control can be a mechanical telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable fric- tion associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveli...

  • Page 596

    Warning! • an improperly adjusted weight distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • weight distributing systems may not be compat- ible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable re...

  • Page 597

    Trailer hitch type and maximum trailer weight hitch type max. Trailer hitch max. Trailer weight class iii bumper hitch - 1500 model 5,000 lbs (2 268 kg) class iv - 1500 model 10,450 lbs (4 740 kg) class v - 2500/3500 models 17,000 lbs (7 711 kg) fifth wheel - 2500/ 3500 models 25,000 lbs (11 339 kg)...

  • Page 598

    Ram 1500 4x2 st slt/outdoorsman sport/laramie 3.6l v-6 8–speed auto- matic transmission standard towing: 5,000 lbs (2 268 kg) max towing: 7,400 lbs (3 379 kg) max payload: 1,920 lbs (871 kg) standard towing: 5,000 lbs (2 268 kg) max towing: 7,400 lbs (3 357 kg) max payload: 1,900 lbs (862 kg) – 5.7l...

  • Page 599

    Ram 1500 4x4 st slt/outdoorsman sport/laramie 3.6l v-6 8–speed auto- matic transmission standard towing: 5,000 lbs (2 268 kg) max towing: 7,250 lbs (3 289 kg) max payload: 1,930 lbs (875 kg) standard towing: 5,000 lbs (2 268 kg) max towing: 7,200 lbs (3 266 kg) max payload: 1,900 lbs (861 kg) – 5.7l...

  • Page 600

    Ram 2500 and 3500 st slt/outdoorsman/sport laramie 5.7l hemi® v-8 6–speed automatic transmission max towing: 13,850 lbs (6 282 kg) max payload: 4,480 lbs (2 032 kg) max towing: 13,810 lbs (6 282 kg) max payload: 4,440 lbs (2 014 kg) max towing: 13,350 lbs (6 055 kg) max payload: 4,410 lbs (2 000 kg)...

  • Page 601

    Trailer and tongue weight always load a trailer with 60% of the weight in the front of the trailer. This places 10% of the gtw on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control ...

  • Page 602

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to “tire safety information/tire and loading in- formation placard” i...

  • Page 603

    Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may ...

  • Page 604

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch uti- lized. Towing requirements — tires • do not attempt to tow a trailer while ...

  • Page 605

    Towing requirements — trailer brakes warning! • do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • towing any trailer will increase your stopping dis...

  • Page 606

    • trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 1,653 lbs (750 kg). Integrated trailer brake module — if equipped your vehicle may have an integrated trailer brake mod- ule (itbm) for electric and electric over hydraulic (eoh) trailer brak...

  • Page 607

    The user interface consists of the following: manual brake control lever slide the manual brake control lever to the right to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes. If the manual brake control lever is activated while the brake is also applied, the g...

  • Page 608

    Adjusting gain note: this should only be performed in a traffic free environment at speeds of approximately 20–25 mph (30–40 km/h). 1. Make sure the trailer brakes are in good working condition, functioning normally and properly ad- justed. See your trailer dealer if necessary. 2. Hook up the traile...

  • Page 609

    9. If the trailer wheels lockup (indicated by squealing tires), reduce the gain setting; if the trailer wheels turn freely, increase the gain setting. Repeat steps 8 and 9 until the gain setting is at a point just below trailer wheel lockup. If towing a heavier trailer, trailer wheel lockup may not ...

  • Page 610

    Caution! Connecting a trailer that is not compatible with the itbm system may result in reduced or complete loss of trailer braking. There may be a increase in stop- ping distance or trailer instability which could result in damage to your vehicle, trailer, or other property. Warning! Connecting a t...

  • Page 611

    Note: do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — g...

  • Page 612

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy traffic. Automatic transmission the “drive” range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. However...

  • Page 613

    When towing a loaded trailer up steep grades at low speeds (20 mph [32 km/h] or below), holding your vehicle in first gear (using the ers switches) can help to avoid transmission overheating. If you regularly tow a trailer for more than 45 minutes of continuous operation, then change the automatic t...

  • Page 614

    Air conditioning turn off temporarily. Air suspension system to aid in attaching/detaching the trailer from the vehicle, the air suspension system can be used. Refer to “air suspension system” in “starting and operating” for further information. Note: the vehicle must remain in the engine running po...

  • Page 615

    Warning! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in a collision. Do not expect that the airbag will perform as de- scribed earlier in this manual. 2500/3500 models only snowplow prep packages are available as a factory installed option. These pack...

  • Page 616

    Caution! The “lamp out” indicator could illuminate if exte- rior lamps are not properly installed. Before plowing • check the hydraulic system for leaks and proper fluid level. • check the mounting bolts and nuts for proper tight- ness. • check the runners and cutting edge for excessive wear. The cu...

  • Page 617

    Note: detach the snowplow when transporting pas- sengers. Vehicle front end wheel alignment was set to specifica- tions at the factory without consideration for the weight of the plow. Front end toe-in should be checked and reset if necessary at the beginning and end of the snowplow season. This wil...

  • Page 618

    General maintenance snowplows should be maintained in accordance with the plow manufacturer’s instructions. Keep all snowplow electrical connections and battery terminals clean and free of corrosion. When plowing snow, to avoid transmission and drive- train damage, the following precautions should b...

  • Page 619

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground two-wheel drive models four-wheel drive models flat tow none not al- lowed see instructions • automatic transmission in park • manual transmission in gear (not in neutral) •...

  • Page 620

    Note: vehicles equipped with air suspension must be lowered to the “entry/exit” (lowest) level, and have automatic leveling disabled, before tying them down (from the body) on a trailer or flatbed truck. Refer to “air suspension – if equipped” for more information. If the vehicle cannot be lowered t...

  • Page 621

    Caution! • towing with the rear wheels on the ground will cause severe transmission damage. Damage from improper towing is not covered under the new vehicle limited warranty. • do not disconnect the driveshaft because fluid may leak from the transmission, causing damage to internal parts. Recreation...

  • Page 622

    Caution! (continued) • tow only in the forward direction. Towing this vehicle backwards can cause severe damage to the transfer case. • automatic transmissions must be placed in park for recreational towing. • manual transmissions must be placed in gear (not in neutral) for recreational towing. • be...

  • Page 623

    Warning! (continued) the parking brake. The transfer case neutral (n) position disengages both the front and rear drive- shafts from the powertrain and will allow the vehicle to move, even if the transmission is in park. The parking brake should always be applied when the driver is not in the vehicl...

  • Page 624

    Shift to neutral (n) is complete. After the shift is completed and the neutral (n) light stays on, release the neutral (n) button. 6. Release the parking brake. 7. Shift the transmission into reverse. 8. Release the brake pedal (and clutch pedal on manual transmissions) for five seconds and ensure t...

  • Page 625

    Will flash continuously until all requirements are met or until the neutral (n) button is released. • the ignition switch must be in the on/run position for a shift to take place and for the position indicator lights to be operable. If the ignition switch is not in the on/run position, the shift wil...

  • Page 626

    • with electronic shift transfer case with rotary selector switch, press and hold the transfer case neutral (n) button until the neutral (n) indicator light turns off. After the neutral (n) indicator light turns off, release the neutral (n) button. After the neutral (n) button has been released, the...

  • Page 627

    11. Shift the transmission into gear, release the brake pedal (and clutch pedal on manual transmissions), and check that the vehicle operates normally. Note: with electronic shift transfer case: • steps 3 and 4 are requirements that must be met prior to pressing the button to shift out of neutral (n...

  • Page 629: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .629 䡵 if your engine overheats . . . . . . . . . . . .629 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .630 ▫ torque specifications . . . . . . . . . . . . . . . . . .631 䡵 jacking a...

  • Page 630

    䡵 manual park release — 8 speed transmission . . . . . . . . . . . . . . . . . . . . . . .680 䡵 towing a disabled vehicle . . . . . . . . . . .682 ▫ two-wheel drive models . . . . . . . . . . . . . . . .684 ▫ four-wheel drive models. . . . . . . . . . . . . . . .685 628 what to do in emergencies.

  • Page 631

    Hazard warning flashers the hazard warning flasher switch is located on the upper switch bank just below the radio. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Pre...

  • Page 632

    Supplement to the radiator and aids in removing heat from the engine cooling system. Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads hot (h), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer dr...

  • Page 633

    Torque specifications lug nut/bolt torque lug nut/ bolt type **lug nut/bolt size lug nut/ bolt socket size 130 ft-lbs (176 n·m) cone m14 x 1.50 22 mm 140 ft-lbs (190 n·m) flanged **use only chrysler recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Note: dual wheels a...

  • Page 634

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten...

  • Page 635

    Jacking and tire changing jacking and tire changing 1500 series trucks warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up...

  • Page 636

    Information center (evic)” in “understanding your instrument panel” for further information. Jack location the jack and jack tools are stored under the front passenger seat. Removal of jack and tools (1500 series) to access the jack and jack tools you must remove the plastic access cover, located on...

  • Page 637

    Release the tool bag straps from the jack and remove tools from bag. Warning! After using the jack and tools, always reinstall them in the original carrier and location. While driving (continued) jack and tools (1500 series) jack and tool bag 6 what to do in emergencies 635.

  • Page 638

    Warning! (continued) you may experience abrupt stopping, rapid accelera- tion or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury. Removing the spare tire 1. Remove the spare tire before attempting to jack up the truck....

  • Page 639

    2. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle. Inserting the jack extension tube into the access hole rotating the wheel wrench handle 6 what to do in emergencies 637.

  • Page 640

    3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. 4. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. Pulling the spare tire out gaining access to the retainer 638 what to do in emergencies.

  • Page 641

    5. Pull the retainer through the center of the wheel. Note: the winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippe...

  • Page 642

    Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jack instructions (1500 series) warning! Careful...

  • Page 643

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 644

    3. Placement of the jack: 4x2 series trucks front jacking location there is a jack location indicator on the rear portion of the lower control arm. When changing a front wheel, place the scissor jack under the rear portion of the lower control arm as shown below. 4x2 front jacking location indicator...

  • Page 645

    4x4 series trucks front jacking location there is a jack location indicator on the rear portion of the lower control arm. When changing a front wheel, place the scissor jack under the rear portion of the lower control arm as shown below. 4x4 front jacking location indicator 4x4 front jacking locatio...

  • Page 646

    4x2 and 4x4 rear jacking location operate the jack using the jack drive tube and the wheel wrench. The tube extension may be used but is not required. For 4x2 and 4x4 trucks, when changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place ...

  • Page 647

    Caution! Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 4. By rotating the lug wrench clockwise, raise the vehicle until the wheel just clears the surface. Warning! Raising the vehicle higher than nec...

  • Page 648

    Warning! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Al- ways stow the jack parts and the extra tire and wheel in the places provided. 7. Install the wheel center cap and remove the wheel blocks. Do not install chrome or aluminum wheel center ...

  • Page 649

    2. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable and position it properly across the wheel opening. 3. Attach the wheel wrench to the jack extension tube with the curved angle facing away from the vehicle. Insert the tube through the access hole bet...

  • Page 650

    4. Rotate the lug wrench handle clockwise until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip, or click three or four times. It cannot be overtight- ened. Push against the tire several times to ensure it is firmly in pl...

  • Page 651

    Reinstalling the jack and tools (1500 series) 1. Tighten the jack all the way down by turning the jack turn-screw counterclockwise until the jack is snug. 2. Position the jack and tool bag. Make sure the lug wrench is under the jack near the jack turn-screw. 3. Secure the tool bag straps to the jack...

  • Page 652

    Note: ensure that the jack slides into the front hold down location. 5. Turn the wing bolt clockwise to secure to the floor pan. Reinstall the plastic cover. Jack hold down fastener jack and tools (1500 series) 650 what to do in emergencies.

  • Page 653

    Warning! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious in...

  • Page 654

    Removal of jack and tools (2500, 3500 series) to access the jack and jack tools you must remove the plastic access cover, located on the side of the front passengers seat. To remove the cover, pull the front part of the cover (closest to the front of the seat) toward you to release a locking tab. On...

  • Page 655

    Remove the jack and tools from the bracket assembly. Turn the jack-turn-screw counterclockwise to release jack from bracket assembly. Jack and tools (2500/3500 series) jack and tools bracket assembly 6 what to do in emergencies 653.

  • Page 656

    Warning! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious in...

  • Page 657

    2. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle. Inserting the jack extension tube into the access hole rotating the wheel wrench handle 6 what to do in emergencies 655.

  • Page 658

    3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. 4. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. Pulling the spare tire out gaining access to the retainer 656 what to do in emergencies.

  • Page 659

    5. Pull the retainer through the center of the wheel. Note: the winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippe...

  • Page 660

    Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jack instructions (2500, 3500 series) warning! C...

  • Page 661

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 662

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare wheel, jack, and tools from storage. 2. Using the lug wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise o...

  • Page 663

    3. Placement of the jack: 4x2 series trucks front jacking location for 2500 and 3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame. Operate the jack using the j...

  • Page 664

    Connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the jack tube extension and wheel wrench. 4x2 and 4x4 rear jacking location for 4x2 and 4x4 trucks, when changing a rear wheel, assemble t...

  • Page 665

    Connect the jack tube extension and wheel wrench. Caution! Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. Note: if the bottle jack will not lower by turning the dial (thumbwheel) by hand, it may be ne...

  • Page 666

    6. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. For the correct lug nut torque refer to “torque specifications” in this section. If in doubt about the cor...

  • Page 667

    Them checked with a torque wrench by you authorized dealer or service station. Warning! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Al- ways stow the jack parts and the extra tire and wheel in the places provided. 7. Install the wheel center c...

  • Page 668

    2. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable and position it properly across the wheel opening. 3. Attach the wheel wrench to the jack extension tube with the curved angle facing away from the vehicle. Insert the tube through the access hole bet...

  • Page 669

    4. Rotate the lug wrench handle clockwise until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip, or click three or four times. It cannot be overtightened. Push against the tire several times to ensure it is firmly in plac...

  • Page 670

    Note: the winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Reinstalling the jack and tools (2500 and 3500 series) 1. Tighten the jack all the way down by turning the jack turn-screw countercl...

  • Page 671

    Note: ensure that the jack and tool bracket assembly slides into the front hold down location. 4. Turn the wing bolt clockwise to secure to the floor pan. Reinstall the plastic cover. Hub caps/wheel covers — if equipped the hub caps must be removed before raising the vehicle off the ground. Jack hol...

  • Page 672

    Caution! Use extreme caution when removing the front and rear center caps. Damage can occur to the center cap and/or the wheel if screwdriver type tools are used. A pulling motion, not a pry off motion, is recom- mended to remove the caps. For single rear wheel (srw) models, use the flat blade on th...

  • Page 673

    Replace the wheel skins first using a rubber mallet. When replacing the hub caps, tilt the cap retainer over the lug nut bolt circle and strike the high side down with a rubber mallet. Be sure that the hub caps and wheel skins are firmly seated around the wheel. Hoisting a conventional floor jack ma...

  • Page 674

    Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations for jump-start the battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. Note: the positive battery post is cov...

  • Page 675

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 676

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end...

  • Page 677

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the dis- charged battery. 2. Disconnect the opposite end of the negative (-) jumper cable...

  • Page 678

    Pressing the accelerator. Use the least amount of accel- erator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the en- gine. Note: for trucks equipped with 8-speed automatic transmission: shifts between drive and reverse can only be achieved at wheel spee...

  • Page 679

    Caution! (continued) • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no trans- mission shifting occurring). Warning! Fast spinning tires can be dangerous....

  • Page 680

    Caution! Tow hooks are for emergency use only to rescue a vehicle stranded off-road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use one ...

  • Page 681

    Center console shifter — if equipped 1. Turn the engine off. 2. Firmly apply the parking brake. 3. Using a small screwdriver or similar tool, remove the shift lever override access cover (located to the right of the shift lever). 4. Press and maintain firm pressure on the brake pedal. 5. Insert the ...

  • Page 682

    Manual park release — 8 speed transmission warning! Always secure your vehicle by fully applying the parking brake, before activating the manual park release. Activating the manual park release will allow your vehicle to roll away if it is not secured by the parking brake or by proper connection to ...

  • Page 683

    2. Using a small screwdriver or similar tool, remove the manual park release access cover, which is just above the parking brake release handle, below and to the left of the steering column. 3. Using the screwdriver or similar tool, push the manual park release lever locking tab (just below the midd...

  • Page 684

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the trans- mission and drivetrain are operable, disabled vehicles may also be towed as described under “recreational towing” in the “starting and operating” section. Note:...

  • Page 685

    Towing condition wheels off the ground 2wd models 4wd models flat tow none if transmission is operable: • transmission in neutral • 30 mph (48 km/h) max speed • 15 miles (24 km) max distance (6– speed transmission) • 30 miles (48 km) max distance (8– speed transmission) see instructions in “recreati...

  • Page 686

    If you must use the accessories (wipers, defrosters, etc.) while being towed, the ignition must be in the on/run position, not the acc position. If the key fob is unavailable or the vehicle’s battery is discharged, refer to ”manual park release” or “shift lever override” in this section for instruct...

  • Page 687

    Caution! Towing this vehicle in violation of the above require- ments can cause severe engine and/or transmission damage. Damage from improper towing is not cov- ered under the new vehicle limited warranty. Four-wheel drive models the manufacturer recommends towing with all wheels off the ground. Ac...

  • Page 689: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . .690 䡵 engine compartment — 5.7l . . . . . . . . . .691 䡵 engine compartment — 6.4l . . . . . . . . . .692 䡵 onboard diagnostic system (obd ii) . . .693 ▫ loose fuel filler cap message . . . . . . . . . . . .693 䡵 emissi...

  • Page 690

    ▫ adding washer fluid . . . . . . . . . . . . . . . . . .705 ▫ exhaust system . . . . . . . . . . . . . . . . . . . . . .706 ▫ cooling system . . . . . . . . . . . . . . . . . . . . . .709 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . .717 ▫ rear axle and 4x4 front driving axle fluid ...

  • Page 691

    䡵 fluid capacities . . . . . . . . . . . . . . . . . . . .755 䡵 fluids, lubricants and genuine parts . .758 ▫ engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .758 ▫ chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . .760 7 maintaining your vehicle 689.

  • Page 692

    Engine compartment — 3.6l 1 — air cleaner filter 5 — battery 2 — engine oil dipstick 6 — washer fluid reservoir 3 — engine oil fill 7 — power distribution center (fuses) 4 — brake fluid reservoir 8 — engine coolant reservoir 690 maintaining your vehicle.

  • Page 693

    Engine compartment — 5.7l 1 — air cleaner filter 7 — washer fluid reservoir 2 — automatic transmission dipstick (6-speed trans only) 8 — power distribution center (fuses) 3 — engine oil fill 9 — power steering fluid reservoir (2500/3500 models only) 4 — engine oil dipstick 10 — coolant pressure cap ...

  • Page 694

    Engine compartment — 6.4l 1 — coolant pressure bottle 6 — battery 2 — transmission dipstick 7 — power distribution center (fuses) 3 — engine oil fill 8 — washer solvent 4 — engine oil dipstick 9 — power steering fluid reservoir 5 — brake fluid reservoir 10 — air cleaner filter 692 maintaining your v...

  • Page 695

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 696

    “understanding your instrument panel” for further in- formation. Tighten the fuel filler cap properly and press the select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap...

  • Page 697

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 698

    Available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedure yourself. Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! Y...

  • Page 699

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 700

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” for further informa- tion. Note: under no circumstances should oil change in- tervals exceed 10,000 miles (16,000 km) or twelve mon...

  • Page 701

    Engine oil viscosity — 3.6l/5.7l engines (1500 models only) mopar® sae 5w-20 engine oil approved to chrysler material standard ms-6395 or equivalent pennzoil® or shell helix® is recommended for all operating tempera- tures. This engine oil improves low temperature starting and vehicle fuel economy. ...

  • Page 702

    • for 2500/3500 trucks with a 5.7l engine operating under a gross combined weight rating of 14,000 lbs (6 350 kg) or greater, sae 5w-30 engine oil is recom- mended for all operating temperatures. Engine oil viscosity — 6.4l engine use pennzoil ultra™ 0w–40 engine or equivalent mopar® oil meeting the...

  • Page 703

    Quality filters should be used to assure most efficient service. Mopar® engine oil filters are a high quality oil filter and are recommended. Engine air cleaner filter refer to the “maintenance schedule” for the proper maintenance intervals. Warning! The air induction system (air cleaner, hoses, etc...

  • Page 704

    Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water. R...

  • Page 705

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 706

    Refrigerant recovery and recycling hfo 1234yf — if equipped hfo 1234yf air conditioning refrigerant is a hydro- fluorocarbon (hfc) that is endorsed by the environmen- tal protection agency and is an ozone-saving product with a low gwp (global warming potential). However, the manufacturer recommends ...

  • Page 707

    Windshield wiper blades clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the w...

  • Page 708

    Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed up, operate the defroster for a few minutes to reduce the possibility of smearing or freezi...

  • Page 709

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 710

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 711

    Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiat...

  • Page 712

    Cooling system — drain flush and refill if the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old engine coolant (anti...

  • Page 713

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 714

    • use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain ...

  • Page 715

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To pre...

  • Page 716

    2. Lift and remove the plastic dipstick from the reservoir neck. 3. Check the coolant level on the dipstick. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing en- gine coolant (antif...

  • Page 717

    Of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Checking coolant level — 6.4l eng...

  • Page 718

    • do not overfill the coolant expansion bottle. • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (anti- freeze) needs to be added, the contents of the coolant expansion bottle must also be protected against freez- ing. • if frequent engine coola...

  • Page 719

    Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “maintenance schedule” for the proper maintenance intervals. Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot rest...

  • Page 720

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid ...

  • Page 721

    Warning! (continued) • do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Rear axle and 4x4 front driving axle fluid level for normal service, periodic fluid level che...

  • Page 722

    Note: the presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage. Limited-slip differ...

  • Page 723

    Automatic transmission selection of lubricant it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “fluids, lubricants, and genuine parts” in this section for fluid specifications....

  • Page 724

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check — eight-speed transmission the fluid level is preset at the factory and does not require adjustment ...

  • Page 725

    Use the following procedure to check the transmission fluid level properly: 1. Monitor the transmission temperature using the evic display, and operate the vehicle as required to reach the normal operating temperature. 2. Park the vehicle on level ground. 3. Run the engine at normal idle speed for a...

  • Page 726

    Note: if it is necessary to check the transmission below the operating temperature, the fluid level should be between the two “cold” (lower) holes on the dipstick with the fluid at 60-70°f / 16-21°c. Only use the cold region of the dipstick as a rough reference when setting the fluid level after a t...

  • Page 727

    Fluid and filter changes — six-speed transmission refer to the “maintenance schedule” for the proper maintenance intervals. In addition, change the fluid and filter(s) if the fluid becomes contaminated (with water, etc.), or if the trans- mission is disassembled for any reason. Appearance care and p...

  • Page 728

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar® car wash, or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover...

  • Page 729

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as...

  • Page 730

    Caution! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s pro- tective finish. Only mopar® whee...

  • Page 731

    Can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar® total clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, c...

  • Page 732

    Glass surfaces all glass surfaces should be cleaned on a regular basis with mopar® glass cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear quarter window ...

  • Page 733

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 734

    4. Once dry, apply a small amount of mopar® spray-on bedliner conditioner to a moist towel or sponge and wipe over the entire surface of the truck bedliner. Warning! Do not use silicon-based protection products to clean your bedliner. Silicon-based products can become slippery and may result in pers...

  • Page 735

    Fuses warning! • when replacing a blown fuse, always use an ap- propriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Failure to use proper fuses may re...

  • Page 736

    Power distribution center the power distribution center is located in the engine compartment near the battery. This center contains car- tridge fuses, micro fuses, relays, and circuit breakers. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number o...

  • Page 737

    Cavity cartridge fuse micro fuse description f06 40 amp green antilock brakes/electronic stability con- trol pump f07 40 amp green starter solenoid f08 20 amp yellow emissions diesel – if equipped f09 40 amp green (cummins diesel) 30 amp pink (1500 ld diesel) diesel fuel heater – if equipped f10 40 ...

  • Page 738

    Cavity cartridge fuse micro fuse description f15 30 amp pink electric park brake right side – if equipped f19 30 amp pink scr – if equipped f20 30 amp pink passenger door module f21 30 amp pink drive train control module f22 20 amp yellow engine control module f23 30 amp pink body controller #1 f24 ...

  • Page 739

    Cavity cartridge fuse micro fuse description f32 30 amp pink drive train control module – if equipped f33 20 amp yellow cummins diesel fuel heater #1 – if equipped / rear blower – if equipped f34 30 amp pink vehicle system interface module #2 – if equipped f35 30 amp pink sunroof – if equipped f36 3...

  • Page 740

    Cavity cartridge fuse micro fuse description f44 10 amp red diagnostic port f46 10 amp red tire pressure monitor f47 10 amp red snow plow (right) – if equipped f49 10 amp red instrument panel cluster f50 20 amp yellow air suspension control module – if equipped f51 10 amp red ignition node module / ...

  • Page 741

    Cavity cartridge fuse micro fuse description f58 20 amp yellow (gas engine) / 25 amp natural (cummins diesel engine) engine cooling pump f60 15 amp blue underhood lamp f61 20 amp yellow power take-off unit – if equipped f62 10 amp red air conditioning clutch f63 20 amp yellow ignition coils (gas), u...

  • Page 742

    Cavity cartridge fuse micro fuse description f69 15 amp blue mod scr 12v (cummins diesel) – if equipped f70 30 amp green fuel pump motor f71 25 amp natural amplifier f72 10 amp red voltage stabilizer modules – if equipped f74 20 amp yellow (gas engine & 1500 ld diesel) / 10 amp red (cum- mins diesel...

  • Page 743

    Cavity cartridge fuse micro fuse description f78 10 amp red engine control module / electric power steering f79 15 amp blue clearance lights f80 10 amp red universal garage door opener / compass f81 20 amp yellow trailer tow right turn/stop lights f82 10 amp red steering column control module/ cruis...

  • Page 744

    Cavity cartridge fuse micro fuse description f93 20 amp yellow cigar lighter f94 10 amp red shifter / transfer case module f95 10 amp red rear camera / park assist f96 10 amp red rear seat heater switch f97 25 amp natural rear heated seats & heated steering wheel – if equipped f98 25 amp natural fro...

  • Page 745

    Caution! • when installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • when replacing a blown fuse,...

  • Page 746

    Interior bulbs bulb number overhead console lamps ts 212–9 dome lamp 7679 for lighted switches, see your authorized dealer for replacement instructions. Exterior bulbs bulb number base quad headlamp – low beam h11 base quad headlamp – high beam 9005 front turn signal lamp (base quad headlamp) 3157na...

  • Page 747

    Bulb number led center high mounted stop lamp (chmsl)/cargo lamp led (serviced at autho- rized dealer) cab roof marker lamps 194na base rear tail/turn and stop lamp 3157k premium rear tail/turn and stop lamp led (serviced at autho- rized dealer) premium backup lamp t20 rear lamp bar id marker lamp 1...

  • Page 748

    5. Remove the upper radiator seal from the vehicle. 6. Remove the two headlamp assembly attachment screws. 7. Reach into the front wheel house ahead of the front wheel, remove the fastener, and lift the cover over the access hole in the front of the wheel house splash shield. Access to the rear of t...

  • Page 749

    9. Remove the headlamp assembly. Grasp the outboard edge of the lamp and pull it straight forward to disengage the ball stud from the plastic grommet. 10. Disconnect the wiring harness connectors from the bulb socket. 11. Replace bulb(s) as necessary. Caution! • do not contaminate the bulb glass by ...

  • Page 750

    Fog lamps — if equipped 1. Reach under and behind the front bumper to access the back of the front fog lamp housing. 2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb. 3. Rotate the bulb counterclockwise ¼ turn to unlock the bulb from the housing. 4. Pull the bulb straight o...

  • Page 751

    2. Pull the outboard side of the lamp rearward far enough to unsnap the two receptacles on the outboard side of the lamp housing from the two plastic snap post retainers in the outer box side panel. 3. Disconnect the wiring harness connectors from the bulb socket. 4. Rotate the bulb socket countercl...

  • Page 752

    Center high-mounted stoplamp (chmsl) with cargo lamp 1. Remove the two screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn the desired bulb socket ¼ turn and remove the socket and bulb from housing. Chmsl mount...

  • Page 753

    4. Pull the desired bulb straight from the socket. Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • outside bulbs: cargo lamps • inside bulb: center high-mounted stop lamp 5. Reverse the p...

  • Page 754

    Cab top clearance lamps — if equipped 1. Remove the two screws from the top of the lamp. 2. Rotate the bulb socket ¼ turn and pull it from the lamp assembly. 3. Pull the bulb straight from it’s socket and replace. Removing rear screw from clearance lamp removing bulb socket from clearance lamp 752 m...

  • Page 755

    Rear lamp bar id marker (dual rear wheels) — if equipped 1. Loosen the two screws and the housing to gain access to the bulb sockets. 2. Turn the socket ¼ turn counterclockwise to access the bulb. 3. Pull the bulb straight out from the socket. 4. Reverse the procedure for installation of the bulbs a...

  • Page 756

    Side marker lamps (dual rear wheels) — if equipped 1. Push rearward on the side marker lamp assembly. 2. Pull the entire assembly from the fender. 3. Turn the socket ¼ turn counterclockwise and remove from assembly to access the bulb. 4. Pull the bulb straight out from socket. 5. Reverse the procedu...

  • Page 757

    Fluid capacities u.S. Metric fuel (approximate) 1500 regular cab shortbed/crew quad cab models 26 gallons 98 liters 1500 regular cab longbed/crew quad cab models (optional) 32 gallons 121 liters 2500/3500 shortbed models 31 gallons 117 liters 2500/3500 longbed models 32 gallons 121 liters engine oil...

  • Page 758

    U.S. Metric 6.4l engines (we recommend you use sae 0w-40 engine oil meeting the re- quirements of chrysler material standard ms-12633 for use in all operating temperatures.) 7 quarts 6.6 liters cooling system 3.6l engine (we recommend you use mopar® antifreeze/coolant 10 year/ 150,000 mile formula t...

  • Page 759

    U.S. Metric 5.7l engine – 2500/3500 models w/heavy duty (we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula that meets the requirements of chrysler material standard ms-12106.) 19.2 quarts 18.2 liters 6.4 liter engine – mopar® antifreeze/engine coolant 10 year/150,000 mile f...

  • Page 760

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology). Engine oil – 5.7 we recommend you use api certified sae 5w-20 engine oil, meeting the ...

  • Page 761

    Component fluid, lubricant, or genuine part engine oil – 6.4l for best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that meet the american petroleum institute (api) categories of sn. The manufacturer recommend...

  • Page 762

    Chassis component fluid, lubricant, or genuine part automatic transmission – eight-speed automatic use only mopar® zf 8&9 speed atf™ automatic transmission fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Automatic transmission – six...

  • Page 763

    Component fluid, lubricant, or genuine part rear axle – 1500 models we recommend you use mopar® synthetic gear lu- bricant sae 75w-140 (ms-8985). Limited-slip rear ax- les require the addition of 5 oz. (148 ml) mopar® limited slip additive (ms-10111). Front and rear axle – 2500/3500 models we recomm...

  • Page 765: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .764 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .767 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 766

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 767

    • 2500 – 3500 models • under no circumstances should oil change intervals exceed 8,000 miles (13,000 km) or twelve months on 2500 – 3500 trucks, whichever comes first. • severe duty all models • change engine oil at 4000 miles (6,500 km) if the vehicle is operated in a dusty and off road environ- me...

  • Page 768

    Required maintenance refer to the maintenance schedules on the following pages for required maintenance. At every oil change interval as indicated by oil change indicator system: • change oil and filter. • rotate the tires. Rotate at the first sign of irregu- lar wear, even if it occurs before the o...

  • Page 769

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176...

  • Page 770

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 771

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 772

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 773

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 775: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .775 ▫ prepare for the appointment. . . . . . . . . . . . .775 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .775 ▫ be reasonable with requests ....

  • Page 776

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .781 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .781 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .781 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .782 774 if...

  • Page 777

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 778

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 779

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 780

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 781

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 782

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 783

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 784

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 785: Index

    Index 10

  • Page 786

    Adding engine coolant (antifreeze) . . . . . . . . . . . .711 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .586 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .580 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . . .187 airbag. . . . . . . ....

  • Page 787

    Fluid type . . . . . . . . . . . . . . . . . . . . . . . . . . . .721 shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .412 special additives . . . . . . . . . . . . . . . . . . . . . . .721 axle fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .719 axle lubrication ...

  • Page 788

    Cellular phone . . . . . . . . . . . . . . . . . . . . . . . . . . .360 center high mounted stop light . . . . . . . . . . . . . .750 center seat storage compartment . . . . . . . . . . . . .239 certification label. . . . . . . . . . . . . . . . . . . . . . . . .588 chart, tire sizing . . . . . . . ...

  • Page 789

    Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . .233 customer assistance . . . . . . . . . . . . . . . . . . . . . . .775 data recorder, event . . . . . . . . . . . . . . . . . . . . . . .82 daytime running lights . . . . . . . . . . . . . . . . . . . .172 dealer service. . . . . ...

  • Page 790

    Electronic speed control (cruise control) . . . . . . . .189 electronic stability control (esc) . . . . . . . . . . . . . .532 electronic vehicle information center (evic) . . . . . .210 electronic vehicle information center (evic) . . . .297 electronic vehicle information center (evic) setup menu ....

  • Page 791

    Exhaust system. . . . . . . . . . . . . . . . . . . . . . . . . . .121 exterior lighting. . . . . . . . . . . . . . . . . . . . . . . . . .170 exterior lights . . . . . . . . . . . . . . . . . . . . . . . . . . .124 filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .701 engine ...

  • Page 792

    Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .577 materials added . . . . . . . . . . . . . . . . . . . . . . . .580 methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . .578 octane rating . . . . . . . . . . . . . . . . . . . . . . . . . .577 requirements . . . . ....

  • Page 793

    Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170 head restraints . . . . . . . . . . . . . . . . . . . . . . . . . .160 heated mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . .144 heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .361 heater, e...

  • Page 794

    Key-in reminder . . . . . . . . . . . . . . . . . . . . . . . . . .19 keyless enter-n-go . . . . . . . . . . . . . . . . . . . . . . . .42 keyless enter-n-go™ lock the vehicle’s doors . . . . . . . . . . . . . . . . . .348 passive entry programming . . . . . . . . . . . . . . . . .42 keyless enter-n...

  • Page 795

    Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174 four-wheel drive indicator . . . . . . . . . . . . . . . .439 hazard warning flasher . . . . . . . . . . . . . . . . . .629 headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . .170 high beam . . . . . . . . . . . ....

  • Page 796

    Manual transmission fluid level check . . . . . . . . . . . . . . . . . . . . . . .720 lubricant selection . . . . . . . . . . . . . . . . . . . . . .760 memory seat . . . . . . . . . . . . . . . . . . . . . . . . . . . .162 methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .578 m...

  • Page 797

    Onboard diagnostic system . . . . . . . . . . . . . . . . . .693 operating precautions . . . . . . . . . . . . . . . . . . . . . .693 operator manual (owner’s manual) . . . . . . . . . . . . .4 outside rearview mirrors . . . . . . . . . . . . . . . . . . .139 overdrive. . . . . . . . . . . . . . . ....

  • Page 798

    Programming transmitters (remote keyless entry) . .24 radial ply tires . . . . . . . . . . . . . . . . . . . . . . . . . .553 radiator cap (coolant pressure cap) . . . . . . . . . . .709 radio operation . . . . . . . . . . . . . . . . . . . . . . . . . .360 rain sensitive wiper system . . . . . . . ...

  • Page 799

    Restraints, occupant . . . . . . . . . . . . . . . . . . . . . . . .50 rotation, tires . . . . . . . . . . . . . . . . . . . . . . . . . . .564 safety checks inside vehicle . . . . . . . . . . . . . . . . .122 safety checks outside vehicle . . . . . . . . . . . . . . . .124 safety defects, reporting...

  • Page 800

    Service contract . . . . . . . . . . . . . . . . . . . . . . . . . .777 service manuals . . . . . . . . . . . . . . . . . . . . . . . . . .780 settings, personal . . . . . . . . . . . . . . . . . . . . . . . . .327 shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .400 automatic...

  • Page 801

    Storage, vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . .379 storing your vehicle . . . . . . . . . . . . . . . . . . . . . . .743 sun roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224 supplemental tire pressure information . . . . . . . . .561 suspension, air. . . . ...

  • Page 802

    Tongue weight/trailer weight . . . . . . . . . . . . . . . .599 tonneau cover . . . . . . . . . . . . . . . . . . . . . . . . . . .731 tonneau cover cleaning . . . . . . . . . . . . . . . . . . . .731 torque converter clutch . . . . . . . . . . . . . . . . . . . .424 tow hooks, emergency . . . . . ....

  • Page 803

    Uconnect® customer programmable features . . . . . . . . . . .350 uconnect® settings . . . . . . . . . . . . . . . . . . . . . .350 uconnect® settings customer programmable features . . . . . . . . . . . .42 passive entry programming . . . . . . . . . . . . . . . . .42 uconnect® settings . . . . . ....

  • Page 804

    Rear sliding . . . . . . . . . . . . . . . . . . . . . . . . . . .246 reset auto-up . . . . . . . . . . . . . . . . . . . . . . . . . .48 wind buffeting . . . . . . . . . . . . . . . . . . . . . . . . . .50 windshield defroster. . . . . . . . . . . . . . . . . . . . . . .122 windshield washers . . ....

  • Page 805

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 806

    1 5 0 0 / 2 5 0 0 / 3 5 0 0 chrysler group llc o w n e r ’ s m a n u a l 2 0 1 4 2014 ram truck 1500/2500/3500 14d241-126-aa first edition printed in u.S.A. R a m t r u c k.