1. DL manuals
  2. RAMSET
  3. Power Tool
  4. D45A
  5. Operator's Safety & Operating Instruction Manual

RAMSET D45A Operator's Safety & Operating Instruction Manual

Manual is about: RAMSET Semi-Automatic, Low Velocity Piston Type Fastening Tool

Summary of D45A

  • Page 1

    Ramset d45a tool operator’s safety & operating instruction manual danger this tool for use by licensed operators only. Read and obey all safety and operating instructions before operating tool. Semi-automatic, low velocity piston type fastening tool.

  • Page 2: Safety Introduction

    Just as no one can merely read a book about driving an automobile and then hope to drive one safely, no one should attempt to use any ramset tool without adequate, one must also be licensed to use a powder actuated tool. No automobile instruction book or instructor can forewarn a learner against all...

  • Page 3: Preparation

    Preparation acceptable base materials powder actuated fastening is suitable for use in the following base materials only: • poured concrete • structural steel • masonry joints (see page 8) never attempt to fasten into any other type of material. Fastening into other materials can cause blindness or ...

  • Page 4: Safety Instructions

    Loads & load selection safety 1. Always make a test fastening after being sure that the base material is suitable for powder actuated fastening. Failure to determine the correct power level to be used may result in the use of excessive power, allowing the fastener to pass completely through the work...

  • Page 5: Danger

    Tool handling safety 1. Always be sure tool is operating properly before attempting to use it. Follow the “daily function test” shown to the right and described on page 9. 2. Always load tool using a disc load selected directly from a box indicating the power load type and number. Never attempt to u...

  • Page 6: Failure to Follow

    Failure to follow instructions can cause injury to the tool operator or to bystanders. Fastener driving safety 1. Only use the tool for fastening into a suitable base material. 2. Never fire the tool without a fastener. Firing a tool without a fastener will cause the piston to strike the work surfac...

  • Page 7: Fasteners

    Your ramset d45a tool uses only the ramset fasteners and loads shown below or listed for the tool in the product catalog. Fasteners fasteners / loads fasteners / loads 7 never use any other types of fasteners or disc loads in the ramset d45a tool. Use of other types of fasteners or loads may cause u...

  • Page 8: Fastening Applications

    Fastening applications your ramset tool can be used for a wide range of fastening needs in a variety of base materials. Reading and following these important fastening guidelines will help you get the best results from your tool, fasteners, and powder loads, as well as help you perform these fasteni...

  • Page 9: Tool Operating Instructions

    Tool operation daily function test always check the tool first to make sure that it does not contain a disc load or fastener. Test the tool several times by depressing the muzzle bushing fully on a hard surface and pulling the trigger. You should hear an audible click as the firing pin releases. Let...

  • Page 10: Tool Operating Instructions

    4. Close the cover and be sure it is locked. Never attempt to make a fastening with the tool cover in the open or unlocked position. 5. Hold the tool perpendicular (90°) to the work surface with both hands and press firmly to fully depress the tool. Maintain firm downward pressure on the tool with b...

  • Page 11: Troubleshooting

    Refer to parts schematic for proper assembly of parts – overdriving of fasteners – excessive power – change to the next lower power level load disc color and number. – soft base material – check base material (see page 3) – tool fails to fire – failure to depress – see “tool does not completely comp...

  • Page 12: D45A Parts Schematic

    D45a parts schematic d45a parts schematic 12.

  • Page 13: Parts List / Maintenance

    Ramset d45a tool parts list key part no. Description 1 323300 muzzle bushing assembly 2 316520 buffer (pkg of 3) 3 30645 piston 4 323020ma barrel retention collar assembly 5 316540 pawl (pkg of 2) 6 323390a barrel assembly 8 308490 latch button assembly 9 13510 cover assembly 10 307890 firing pin as...

  • Page 14: Disassembly

    Disassembly 14 disassembly tool disassembly 1. Uscrew the barrel retention collar and slide it away from the tool housing. Handle the tool carefully after the sleeve is unscrewed to prevent the two barrel pawls from falling out. 2. Remove the two pawls from the slots in the sides of the tool housing...

  • Page 15: Disassembly

    Disassembly 15 disassembly 6. Slide the barrel assembly away from the muzzle bushing. 7. Remove the piston from the muzzle bushing. 8. Remove the buffer from the muzzle bushing. 9. Inspect all parts for wear or damage and clean or replace as required. Use detergent oil and cleaning brush. Wipe parts...

  • Page 16

    D45a warranty and limitations powder actuated tool manufactures' institute inc. Tm concrete fastening systems glendale heights, il 60139 800-ramset6 (1-800-726-7386) www.Ramset.Com buy with confidence... Buy from your authorized distributor an illinois tool works company © illinois tool works 2009 p...