Rane TTM 57SL Operator's Manual - page 35
33
miscellaneous options
expand library on track scroll
With this option turned on, the hardware panel will hide tempo-
rarily while you are using the mixer to scroll through your library.
flashing deck indicator
The flashing deck indicator shows which Virtual Deck is selected
by the deck button on the mixer. When this option is on, a red
border will flash around the selected virtual deck.
foot switch type
The TTM 57SL supports 1, 2 or 3 button footswitches. Click on
the number that corresponds to your foot switch.
reset controls to defaults
Each of the software control assignments can be customized.
Click this button to reset all the control assignments/mappings to
their default state.
Control source
Any of the four inputs on the TTM 57SL can be set to control
Scratch
LIVE
. Use these two knobs to choose the inputs that are
used to control Scratch
LIVE
.
Playback
general
track end warning
Enable track end warning to flash the virtual deck as you ap-
proach the end of the track. The label will start flashing 20
seconds from the end of the record. The track end warning does
not apply to any tracks under 1 minute long.
playback keys use shift
This is checked by default. Unchecking this option will enable all
of these keys without pressing shift or having caps lock on. This
applies to all cue points (1...0) and cue controls (QWERTY etc).
See page 31 for all keyboard shortcuts.
lock playing deck
Every DJs nightmare used to be lifting the needle of the wrong
turntable in the middle of a set. This setting helps to avoid the
digital equivalent – loading a new track to the wrong deck. When
checked, you can only load a track if the target deck is stopped.
sort cues chronologically
The five cue points can be placed in
any order, and can be dragged up and
down if you wish to reorder them. If
you prefer to lock them to chronologi-
cal order, turn this option on.
use auto gain
For songs with overviews built (by
version 1.7.2 or later), check this if
you want to use the calculated auto
gain value while playing songs. There
is also a target gain dropdown menu
next to this option, that sets the target
gain that you would like. This can be turned on / off, and the
target gain changed on the fly. If you change the target gain while
a song is loaded to a deck, the change will apply the next time a
song is loaded.
When a track is in auto gain mode (auto gain is turned on
and the track has an auto gain setting), the track gain knob ap-
pears depressed to provide visual feedback that auto gain is in
effect for that track. To fine tune your gain values, you can still
change each file by the gain knob. To reset the gain to the calcu-
lated auto gain value, alt-click the gain knob.
hi-fi resampler
This significantly reduces digital distortion at very slow or very
fast record speeds, increasing the CPU load slightly. This option is
on by default, and the old resampler is used when switched off.
on song load
play from start
Enable this to start all tracks from the beginning when loaded in
relative
and
internal
modes. If this setting is not enabled, fresh-
ly loaded tracks will continue to play from the point the last track
was at. This option is on by default. This option is overridden by
the
instant doubles
and
play from first cue point
options.
instant doubles
This quickly matches the playhead position of two tracks. With
this on, when you load a track on one virtual deck already loaded
on the other virtual deck (it must be the same file), the playhead
will jump to the position of the track that was loaded first, with
the keylock state and looping settings copied. This setting over-
rides
play from start
and
play from first cue point
options.
Play from first cue point
Enable this to start all tracks from the first cue point when loaded
in
relative
and
internal
modes. This overrides
play from start
.
braking (internal mode)
This controls how fast the deck stops when play is stopped.
Counterclockwise, the stop is immediate. Clockwise rotation in-
creases the stop from a finger grab all the way to a slow turntable
power-down.
audio output
Sets the audio output to mono or stereo.