Rangemaster Toledo 110 Dual Fuel Users Manual & Installation - page 28
28
WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
3. To Remove Side Panels
Disconnect from electricity supply.
Remove the Control Panel - see 1. Pull the cooker
forward. Remove the 4 retaining screws for each panel (1
at the front base, 1 on the top and 2 at the rear).
Reassemble in reverse order.
4. To Remove Ignition or light Switch
Disconnect from electricity supply.
Remove the Control Panel - see 1.
NB. The old switch may be destroyed during removal.
Remove the old switch from its bezel by griping the
switch body behind the control panel and twisting
sharply. The switch bezel can then be removed by folding
back its locking wings and pushing forward. Fit the new
bezel to the control panel by fi rst lining up the raised
key on its body with the cutout in the control panel and
pushing it in from the front. Assemble the new switch
to the bezel by lining up the key sections and pushing
home. Fit the new button by pushing in from the front.
Replace Control Panel in reverse order and test for correct
operation.
5. To Remove Clock
Disconnect from electricity supply.
Remove the Control Panel (See 1). Pull off the timer
control button(s).
Remove the timer/mounting bracket assembly from the
control panel by removing the fi xing screws.
Remove the timer from its mounting bracket by
depressing the plastic lugs on the timer case, at the same
time pulling the unit forward.
Reassemble in reverse order. When replacing leads refer
to the wiring diagram. Check operation of timer.
6. To Remove a Thermostat
Disconnect from the electricity supply.
Remove control panel and hotplate (see 1 & 2). Open
oven door. Remove oven furniture and slide out oven
roof liner if fi tted.
For RH oven, remove thermostat phial cover (2 screws).
Unclip the thermostat phial from the clips in the oven
back.
For LH oven pull cooker forward to gain access to the
cover box at the rear of the cooker. Remove the four
screws securing the cover and lift clear.
Feed the thermostat capillary out of the oven. Disconnect
wiring from thermostat. Remove 2 screws holding
thermostat to mounting panel. Fit new thermostat
and reassemble in reverse order. Ensure that the phial
is clipped to the oven back with the phial centrally
positioned between the clips.
Check operation of thermostat.
7. To
Change
Grill
Controller
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2).
Disconnect wiring from controller. Remove 2 screws
holding controller to mounting panel. Fit new controller
and reassemble in reverse order. Check for correct
operation.
BEFORE SERVICING ANY GAS CARRYING COMPONENTS
TURN OFF GAS SUPPLY.
8. To
Change
Control
Taps
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2).
Undo compression fi tting at the rear of the tap. Remove
the fi xings that secure the tap to the gas rail. Remove
the tap. Remove and discard the gasket seal. Fit new
gasket seal to replacement tap. Re-assemble in reverse
order. Check the appliance is gas sound. Check hotplate
ignition.
9. To Change Hotplate Burner Injector
Remove burner cap and head. Remove old jet. Fit new
injector. Reassemble in reverse order. Check appliance is
gas sound.
10. To Change Hotplate Burner Electrode
Lift off pan supports, remove burner cap. Remove the
screw holding the electrode. Pull electrode vertically
up suffi
ciently to grip the lead between thumb and
forefi nger. Pull off the electrode, but keep hold of the
lead. Fit new electrode to the lead. Fix electrode in
burner with screw. Replace burner cap. Check the burner
ignition. Replace pan supports.
11. To Remove or Change a Hotplate Burner.
Remove the hotplate tray (see 2).
The burners except the right hand wok burner
are mounted on support struts. For these burners,
disconnect the burner feed pipes at the burner. Remove
the screws at the front and rear holding the support
stru ts. Lift the strut and burners clear. The burners are
fi xed to the support struts with 2 screws. Remove the
appropriate burner and fi t the new one. Reassemble in
reverse order. Check burner operation is satisfactory.
RH Wok burner
Disconnect the burner feed pipes at the burner. Fit the
new one and reassemble in reverse order. Check burner
operation is satisfactory.