Raypak D-2 Power Vent Installation & Operating Instructions Manual

Manual is about: For 206A, 207A, 266A; 267A; 336A; 406A 407A Swimming Pool & SPA Heaters

Summary of D-2 Power Vent

  • Page 1

    Installation & operating instructions catalog no. 6000.57f effective: 12-02-08 replaces: 5-20-08 p/n 241086 rev. 7 warning: if these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or death . For your safety: do not store or use gasoline...

  • Page 2

    2 rev. 7 reflects the following: changes to: the text in paragraph one of the venting section on page 8..

  • Page 3

    Warnings 4 pay attention to these terms 4 receiving equipment 5 general specifications 5 installation 5 mounting the assembly 5 wiring a power vent assembly to an appliance with iid ignition 8 venting 8 wiring diagrams 10 182-260 h4/wh1 (atmospheric) 10 181-261 h4/wh1 (low nox) 11 sequence of operat...

  • Page 4

    Danger: indicates the presence of immediate hazards which will cause severe personal injury, death or substantial property damage if ignored. Warning: indicates the presence of hazards or unsafe practices which could cause severe personal injury, death or substantial property damage if ignored. Caut...

  • Page 5

    Receiving equipment on receipt of your equipment it is suggested that you visually check for external damage to the carton. If the carton is damaged, it is suggested that a note be made on the bill of lading when signing for equipment. Remove the complete assembly from the carton if it is damaged re...

  • Page 6

    6 7. Mount the power vent on the outer top. 8. Route the conduit harness of the power vent thru the outer top hole, around the adapter towards the back of the unit. Continue routing the harness thru the corner slot, which leads to open area behind the access panel. Finally, route only the wire harne...

  • Page 7

    7 u.S. Installations 1 canadian installations 2 a clearance above grade, veranda, porch, deck, or balcony 1 ft (30 cm) 1 ft (30 cm) b clearance to window or door that may be opened 4 ft (1.2m) below or to side of opening; 1 foot (30 cm) above opening 3 ft (91 cm) c clearance to permanently closed wi...

  • Page 8

    8 wiring a power vent assembly to an appliance with iid ignition venting the vent pipe must be the same size or one size larg- er than what is indicated. The d-2 power vent is capable of 360-degree discharge rotation and oper- ates with a positive vent static pressure and with a vent gas temperature...

  • Page 9

    9 left side the d-2 power vent assembly includes a wire harness, shown in fig. 6 below, which provides quick connec- tions with the respective controls in the heater control box. The harness is of sufficient length to fit the appliance for which it is sized. Reference the wiring diagram supplied wit...

  • Page 10

    10 wiring diagrams—182-260 h4/wh1 (atmospheric).

  • Page 11

    11 181-261 h4/wh1 (low nox).

  • Page 12

    12 dimensional data 181 18.13 12.38 7.88 4.25 182 18.13 12.38 7.88 4.25 260 18.13 12.38 7.88 4.25 261 18.13 12.38 7.88 4.25 330 17.50 15.75 7.63 6.00 331 17.50 15.75 7.63 6.00 400 17.50 15.75 7.63 6.00 401 17.50 15.75 7.63 6.00 model no. A b c d 181 18.13 12.38 7.88 4.25 182 18.13 12.38 7.88 4.25 26...

  • Page 13

    13 sequence of operation on call for heat, the d-2 power vent fan (and appli- ance pump) start. When the flow switch circuits close, the ignition system consisting of an electronic spark module, pilot gas system and flame sensor, are ener- gized. When draft proving switch closes and all safety circu...

  • Page 14

    14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 call out description 181-261 331-401 1 power vent relay 008784f 008784f 2 power vent blower 008156f 008156f 3 power vent no pressure switch 008062f 008135f 4 elbow 4"-90° with screen 010827f 010827f 5 power vent flue box 008682f 008683f 6 power vent base assemb...

  • Page 15

    15.

  • Page 16: Www.Raypak.Com

    Www.Raypak.Com raypak, inc., 2151 eastman avenue, oxnard, ca 93030 (805) 278-5300 fax (805) 278-5468 litho in u.S.A..