Smarthome 4071 User Manual - page 15
ControLinc
™
Maxi
™
User’s Guide
Using the ON and OFF Button Pairs
The ON and OFF Buttons have a dual purpose. If you tap them briefly, they turn X10 Devices linked to the
address they control on or off. If you hold them down, the ON Button will brighten and the OFF Button will dim
any dimming modules linked to them. Holding down will not affect any non-dimmable (switchable) modules.
So, if you just want to turn things on or off, tap the appropriate button – don’t hold it down.
• To turn ON only those X10 Devices linked to an ON/OFF Button Pair, tap the ON Button of the Pair.
ControLinc Maxi will beep and its Status LED will blink off twice. Dimmable modules will go to whatever On-
Level they were set up for, at whatever Fade Rate they were set up for. Switchable modules will immediately
go full on.
• To turn OFF only those X10 Devices linked to an ON/OFF Button Pair, tap the OFF Button of the Pair.
ControLinc Maxi will beep and its Status LED will blink off twice. Dimmable modules will go full off at whatever
Fade Rate they were set up for. Switchable modules will immediately go full off.
• To brighten only those dimmable X10 Devices linked to an ON/OFF Button Pair, press and hold the ON
Button of the Pair. ControLinc Maxi will beep and its Status LED will blink off once. Dimmable modules will
begin to brighten, unless they are already fully bright. Switchable modules will not be affected. When you let
up, dimmable modules will stop going brighter and ControLinc Maxi’s Status LED will blink off again.
• To dim only those dimmable X10 Devices linked to an ON/OFF Button Pair, press and hold the OFF Button
of the Pair. ControLinc Maxi will beep and its Status LED will blink off once. Dimmable modules will begin to
dim, unless they are already fully off. Switchable modules will not be affected. When you let up, dimmable
modules will stop going dimmer and ControLinc Maxi’s Status LED will blink off again.
Using the ON and OFF Buttons (Lower Left, with Cover Closed)
The ON and OFF Buttons will turn on or turn off all X10 Devices linked to the addresses programmed to all 5 of
the On/Off Button Pairs. If the Button Pairs are split into individual buttons (See Programming Individual
Buttons), only the addresses programmed to the top 5 buttons will be controlled by the On/Off Buttons.
• To turn ON all and X10 Devices linked to the addresses programmed to all 5 of the On/Off Button Pairs, tap
the ON Button. ControLinc Maxi will beep and its Status LED will blink off once. Dimmable modules will go
to whatever On-Level they were set up for, at whatever Fade Rate they were set up for. Switchable modules
will immediately go full on.
• To turn OFF all INSTEON and Devices linked to the addresses programmed to all 5 of the On/Off Button
Pairs, tap the ALL OFF Button. ControLinc Maxi will beep and its Status LED will blink off once. Dimmable
modules will go full off at whatever Fade Rate they were set up for. Switchable modules will immediately go
full off.
Using the BRIGHT and DIM Buttons
The BRIGHT and DIM Buttons will brighten or dim only those X10 Devices linked to the last ON/OFF Button Pair
you used. Switchable modules will not be affected. Pressing and holding the BRIGHT and DIM Buttons will
adjust the brightness continuously, while tapping the buttons will adjust the brightness one of 32 steps for each
tap.
• To continuously brighten only those X10 Devices controlled by the last ON/OFF Button Pair you used, press
and hold the BRIGHT Button. ControLinc Maxi will beep and its Status LED will blink off once. Dimmable
modules will begin to brighten, unless they are already fully bright. Switchable modules will not be affected.
When you let up, dimmable modules will stop going brighter and ControLinc Maxi’s Status LED will blink off
again.
• To continuously dim only those X10 Devices controlled by the last ON/OFF Button Pair you used, press and
hold the DIM Button. ControLinc Maxi will beep and its Status LED will blink off once. Dimmable modules
Page 15 of 20