1. DL manuals
  2. TANDBERG
  3. Software
  4. 1000 MXP
  5. User Manual

TANDBERG 1000 MXP User Manual

Summary of 1000 MXP

  • Page 1

    User manual software version f5 d13722.05 june 2006 this document is not to be reproduced in whole or in part without permission in writing from:.

  • Page 2: Trademarks and Copyright

    Tandberg 1000 mxp ii trademarks and copyright all rights reserved. This document contains information that is proprietary to tandberg. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, electronically, mechanically, by photocopy...

  • Page 3

    User manual iii ecos ecos, the embedded configurable operating system. Copyright (c) 1998, 1999, 2000, 2001, 2002, 2003 red hat, inc. Copyright (c) 2002, 2003 john dallaway copyright (c) 2002, 2003 nick garnett copyright (c) 2002, 2003 jonathan larmour copyright (c) 2002, 2003 andrew lunn copyright ...

  • Page 4

    Tandberg 1000 mxp iv disclaimer the information in this document is furnished for informational purposes only, is subject to change without prior notice, and should not be construed as a commitment by tandberg. The information in this document is believed to be accurate and reliable; however tandber...

  • Page 5: Environmental Issues

    User manual v environmental issues thank you for buying a product which contributes to a reduction in pollution, and thereby helps save the environment. Our products reduce the need for travel and transport and thereby reduce pollution. Our products have either none or few consumable parts (chemical...

  • Page 6

    Tandberg 1000 mxp vi information for recyclers as part of compliance with the european weee directive, tandberg provides recycling information on request for all types of new equipment put on the market in europe after august 13th 2005. Please contact tandberg at recycling@tandberg.Net and provide t...

  • Page 7: Operator Safety Summary

    User manual vii operator safety summary operator safety summary for your protection please read these safety instructions completely before you connect the equipment to the power source. Carefully observe all warnings, precautions and instructions both on the apparatus and in these operating instruc...

  • Page 8

    Tandberg 1000 mxp viii • the plug connecting the power cord to the product/power supply serves as the main disconnect device for this equipment. The power cord must always be easily accessible. • route the power cord so as to avoid it being walked on or pinched by items placed upon or against it. Pa...

  • Page 9: Table of Contents

    Tandberg 1000 mxp x table of contents 1 introduction............................................................................................................................... 1 1.1 at a glance .........................................................................................................

  • Page 10

    User manual xi 3.12.2 conference layout................................................................................................... 74 3.12.3 terminal names....................................................................................................... 75 3.12.4 chair control.............

  • Page 11

    Tandberg 1000 mxp xii 5.4.4 video quality.......................................................................................................... 145 5.4.5 call settings........................................................................................................... 148 5.5 audio ..........

  • Page 12: 1 Introduction

    1 1 introduction the tandberg 1000 mxp provides essential video features for face to face meetings for small groups and offices with the quality and reliability found in all tandberg equipment. Users can dial in from a video system outside the enterprise without being registered to a gatekeeper the ...

  • Page 13

    Tandberg 1000 mxp 2 disturbance from gsm mobile phones and blackberry devices is eliminated by a noise filter. Video quality features which ensure high quality video include: natural video tf which provides a 60 fields per second true interlaced picture. Sxga input dvi-i (analog or digital). H.264 v...

  • Page 14

    Introduction 3 pc zoom which allows the native resolution pc image to be zoomed in/out with the remote control to get sxga resolution. Users can display video and presentations in the best layout based on the situation. Supported screen layouts are: picture in picture (pip) picture outside picture (...

  • Page 15: 1.1 At A Glance

    Tandberg 1000 mxp 4 1.1 at a glance camera the camera is an integrated part of the unit and is centrally placed just above the monitor. Monitor the digital lcd displays the far-end and near-end videoconferencing sites in addition to the menu. Codec the codec is the heart of the system. Its main task...

  • Page 16: 1.2 Menu Structure

    Introduction 5 1.2 menu structure the menu is available for all users and contains all the functionality of the system. The control panel contains all the settings of the system. Making changes to the settings will change the behavior of the system. The menu structure is shown below..

  • Page 17

    Tandberg 1000 mxp 6 note that the system features and menu settings may vary depending on network selection and software package..

  • Page 18: 2 Installation

    7 2 installation precautions: never install communication wiring during a lightning storm. Never install jacks for communication cables in wet locations unless the jack is specifically designed for wet locations. Never touch uninstalled communication wires or terminals unless the telephone line has ...

  • Page 19: 2.1 Unpacking

    Tandberg 1000 mxp 8 2.1 unpacking the tandberg 1000 mxp consists of the following items: videoconferencing system with built-in camera remote control batteries user manual on cd power supply cables.

  • Page 20: 2.2  Connecting Cables

    Installation 9 2.2 connecting cables 1. Power cable connect the power supply to the dc in input on the system. Connect the power cable to the power supply. Connect the power cable to an electrical distribution socket. 2. Isdn cables connect the isdn cables to the isdn connectors on the system. Conne...

  • Page 21

    Tandberg 1000 mxp 10 3. Plug for headset (optional) the tandberg 1000 has a 2.5mm 3-pole mini-jack connector at its left side marked with a headset symbol. This allows the user to connect a standard telecommunications headset to the system. Pressing the push button in front of the unit toggles betwe...

  • Page 22: 2.3 Monitor Configuration

    Installation 11 2.3 monitor configuration power on switch the system on by connecting the power cable to an electrical distribution socket. After the system has performed a self-test routine, the menu will be displayed on the monitor..

  • Page 23: 2.4 System Configuration

    Tandberg 1000 mxp 12 2.4 system configuration the system must be configured for each installation. Configuration settings can be made via the system menu. Navigate through the menu system using the arrow keys and ok. Remember to press the save button on the bottom of each menu to save the changes. P...

  • Page 24

    Installation 13 5. Screen settings the settings may be left unchanged if no special needs are required. The display layout may be changed at any time using the layout button on the remote control. 6. Software options to activate options for the system, a new option key must be entered in the softwar...

  • Page 25

    Tandberg 1000 mxp 14 remember to save any changes made in the menu by selecting the save button on the menu line and pressing ok. * the international name field is only visible if the system name contains asian and non-latin character text input..

  • Page 26: 3 General Use

    15 3 general use wake up the system when the system is not in use, it is in standby mode and the screen is black. Wake up the system by picking up the remote control. An incoming call or pressing any key on the remote control will also wake up the system..

  • Page 27: 3.1 The Welcome Screen

    Tandberg 1000 mxp 16 3.1 the welcome screen when the system is switched on, the welcome screen will be displayed. The welcome screen presents the menu and displays your main camera image in the background (display main camera is the default setting). The isdn/ip numbers and the system name are displ...

  • Page 28: 3.2 Using The Remote Control

    Administrator settings 17 3.2 using the remote control the system is controlled with a remote control. Think of the remote control as a mobile phone with number keys and call keys. Use the arrow keys and press ok to navigate through the menus. The system’s most commonly used functions are also acces...

  • Page 29

    Tandberg 1000 mxp 18 in and out.* 12. Selfview displays your outgoing video. Press selfview again to turn selfview off, see selfview . 13. Use the phone book to store and recall video contacts for easy placement of calls, see phone book . 14. Use the red end call key to end the current call. Pressin...

  • Page 30

    Administrator settings 19 the remote control (trc 4)**: 1. Change video source. If possible, you will start open a dual stream. Press the video source button again to stop the dual stream. 2. Mic off turns your microphone on and off, see mic off . 3. Arrow keys are used for navigation in the menu an...

  • Page 31

    Tandberg 1000 mxp 20 presentation source. If the presentation key is held down for 1 second then the presentation video sources menu will appear, see presentation key . 12. Press ok/menu to show the menu and to select menu items, see navigation . 13. Use zoom + and – to zoom the camera in and out.* ...

  • Page 32: 3.2.1 Navigation

    Administrator settings 21 3.2.1 navigation arrow keys and ok navigate in the menu with the arrow keys on the remote control. The orange selector on screen shows the selected item. Press ok to select. Cancel key in the menu, pressing cancel (x) will hide the menu. If the menu is hidden, bring it back...

  • Page 33: 3.2.2

    Tandberg 1000 mxp 22 3.2.2 selfview the term “selfview” means the outgoing image. In a normal call using the main camera, this is the image of you. The selfview button toggles the images between far end, selfview and dual video (if any). How to use selfview: 1. Outside a call, pressing the selfview ...

  • Page 34

    Administrator settings 23 example: you are using the system as a pc and get an incoming call. When the setting “use screen as local pc monitor” is on, you will keep your pc image displayed locally and the incoming call pops up in a pip or as smaller images in a 1+3 layout, depending on your system. ...

  • Page 35: 3.2.3

    Tandberg 1000 mxp 24 3.2.3 picture layout the layout of the screen can either be shown as picture in picture (pip) or picture outside picture (pop) when displaying more than one video image. The behavior of the layout button is dependent on the picture layout setting in control panel – general - scr...

  • Page 36: 3.2.4

    Administrator settings 25 3.2.4 mic off to mute the microphone during a call, press the mic off button. An on-screen indicator appears in the upper right corner when the microphone is off. In a call, if audio is detected, the on-screen symbol will start to flash. Pressing the mic off button one more...

  • Page 37: 3.2.5

    Tandberg 1000 mxp 26 3.2.5 volume + and - press the volume key to adjust the volume level. An on-screen indicator will show the current level..

  • Page 38: 3.2.6

    Administrator settings 27 3.2.6 number and letter keys pressing a number key when outside a call will bring up the call menu. When in a call, the number keys are used for camera presets. Press a number and go to the corresponding camera preset (see camera presets ). However, when accessing an input ...

  • Page 39: 3.2.7

    Tandberg 1000 mxp 28 3.2.7 touch tones to activate dialing touch tones during a call, press the touch tones button. Otherwise the number keys will work as configured in the number key mode, see control panel – menu settings – number key mode. An indicator will let you know that touch tones are enabl...

  • Page 40: 3.2.8

    Administrator settings 29 3.2.8 presets and extension numbers when pressing a number key on the remote control, while in a call, the user can decide what shall happen. The system can be configured to act automatic or manual. While in a call, the user presses a number key to: • add another call • dia...

  • Page 41: 3.3 On-Screen Indicators

    Tandberg 1000 mxp 30 3.3 on-screen indicators the system has a number of icons signaling different settings: microphone off this indicator is shown when the microphone is turned off. Press the mic off button again to turn the microphone back on, see mic off for details. Volume off this indicator is ...

  • Page 42

    Administrator settings 31 telephone this indicates that there is a telephone participant in the conference. The displayed number indicates how many telephone participants there are in the conference. Duo video / h.239 this indicates that there is a dual video stream sent from you (near end). The fea...

  • Page 43: 3.4 Using The Menu

    Tandberg 1000 mxp 32 3.4 using the menu press the menu button on the remote control to display the menu. The menu contains all functions needed in order to control the system. The menu contains the following items: make a call standby / end call camera control* presentation conference services contr...

  • Page 44: 3.5 Make A Call

    Administrator settings 33 3.5 make a call it is easy to make a call: 1. Press the green call button on remote control and dial number 2. Press the green call button again to initiate the call display the call menu by either: 1. Select make a call from the menu, or 2. Press the green call button on t...

  • Page 45: 3.5.1

    Tandberg 1000 mxp 34 3.5.1 place a call the tandberg system can make both video calls and telephone calls . A call type selector button is placed to the right of the number entry field. The button shows if it is a video call (default) or a telephone call. Press the button to show a drop down list to...

  • Page 46

    Administrator settings 35 place the call by either: 1. Use the arrow button on the remote control to select the place call icon and press ok, or 2. Press the green call button on the remote control. Tip: when dialing a telephone number and pressing the green call button on the remote control, the sy...

  • Page 47: 3.5.2 Call

    Tandberg 1000 mxp 36 3.5.2 call settings the call settings specifies the quality of the call. Each call will be set up with the default call settings if the settings are not altered. In this case the field is labeled default call settings. If the settings for some reason are altered for the current ...

  • Page 48: 3.5.3 Sip

    Administrator settings 37 3.5.3 sip services sip enables you to use the features add call and transfer even if your system doesn’t have multipoint capabilities. To get the sip services available, you have to make a call using sip as your net. (see call settings) 3.5.3.1 add call you can add another ...

  • Page 49: 3.5.4 Streaming

    Tandberg 1000 mxp 38 3.5.4 streaming streaming lets you broadcast your meeting to participants on the web. The web participants can listen to the meeting, see snapshots, but not participate themselves. Snapshots of current stream (if multisite), selfview, far end and duovideo streams are accessible ...

  • Page 50

    Administrator settings 39 more than 2 router hops. Streaming source* auto: enables streaming of both local and far end video. Selection of which site to be streamed is done using voice switching (the site that speaks is streamed). Local: only the local video will be streamed. Remote: only the far en...

  • Page 51: 3.5.5

    Tandberg 1000 mxp 40 3.5.5 dialing in from outside the enterprise dialing in without being registered to a tandberg gatekeeper the feature enhancement enables dialing through a tandberg gatekeeper without being registered to it. This makes it easy to call in from a video system outside the enterpris...

  • Page 52: 3.6 Answer An Incoming Call

    Administrator settings 41 3.6 answer an incoming call how to answer an incoming call: to accept an incoming call, press the ok button or the green call button on the remote control. Answering a call with the push-button the push-button on the front panel of the unit works as a connect button during ...

  • Page 53: 3.7  End Call

    Tandberg 1000 mxp 42 3.7 end call how to end a call: press the red end call button on the remote control, or press the menu button on the remote control to display the menu and select end call. When the end call dialog box is displayed either: press the red end call button on the remote control agai...

  • Page 54: 3.8 Standby

    Administrator settings 43 3.8 standby the system will automatically go to standby mode when it is not in use. In standby mode, the screen(s) are black. It is however still possible to receive incoming calls. How to enter standby mode manually: select standby from the menu and select standby now, or ...

  • Page 55: 3.8.1

    Tandberg 1000 mxp 44 3.8.1 delay standby for 1 hour delay standby for 1 hour postpones the system from entering standby mode for 1 hour. This function is useful when using the monitors for a local presentation to prevent the system from automatically blanking the monitors. It is also possible to pos...

  • Page 56: 3.8.2

    Administrator settings 45 3.8.2 delay standby for 3 hours delay standby for 3 hours postpones the automatic standby mode for 3 hours. This function is useful when using the monitors for a local presentation to prevent the system from automatically blanking the monitors. It is also possible to postpo...

  • Page 57: 3.8.3

    Tandberg 1000 mxp 46 3.8.3 do not disturb to prevent the system from accepting any incoming calls, activate the do not disturb function. The caller will hear a busy tone when calling the system. The monitor will be black when do not disturb is active, see figure below. This is useful when using the ...

  • Page 58: 3.9 Phone Book

    Administrator settings 47 3.9 phone book the phone book is available via the phone book button on the remote control or from the make a call menu. Using the phone book is time saving and prevents the user from inadvertently calling the wrong number. The contacts are sorted alphabetically. The contac...

  • Page 59

    Tandberg 1000 mxp 48 the following information is available from the phone book: placed calls missed calls received calls my contacts global contacts.

  • Page 60: 3.9.1 Call

    Administrator settings 49 3.9.1 call log the call log lists placed calls, missed calls and received calls. That allows the user to see which calls that are made in the past. The lists contain a maximum of 30 numbers and the numbers are stored in these lists until the system is restarted. If the cont...

  • Page 61: 3.9.2 My

    Tandberg 1000 mxp 50 3.9.2 my contacts my contacts are the locally stored contacts on the system. This means that it is possible to add new contacts and edit or delete existing contacts. My contacts can store up to 200 contacts. How to make a call using my contacts: 1. Find the desired contact using...

  • Page 62

    Administrator settings 51 the following functions are available from my contacts: call now new contact edit contact delete contact close.

  • Page 63

    Tandberg 1000 mxp 52 3.9.2.1 add new contact the new contact function is available from my contacts . Add a new contact to my contacts by: 1. Select the new contacts button to open the new contacts dialog box. 2. Enter name by using the letter keys on the remote control. Input will automatically be ...

  • Page 64

    Administrator settings 53 3.9.2.2 edit contact the edit contact function is available from my contacts . How to edit a contact in the local phone book: 1. Select the contact that is to be edited. 2. Press the left arrow on the remote control, followed by the down arrow until the edit contact icon is...

  • Page 65

    Tandberg 1000 mxp 54 3.9.2.3 delete contact the delete contact function is available from my contacts . How to delete a contact: 1. Select the contact that is to be deleted. 2. Press the left arrow on the remote control, followed by the down arrow until the delete contact icon is selected. The delet...

  • Page 66: 3.9.3 Global

    Administrator settings 55 3.9.3 global contacts when selecting phone book the phone book opens showing the global contacts* or the corporate directory** below the folders placed calls, missed calls, received calls and my contacts. These contacts cannot be changed locally by the system, only from the...

  • Page 67

    Tandberg 1000 mxp 56 3.9.3.1 up one level global contacts can be arranged in a tree structure with several sub folders. Use the up one level button to navigate up in the tree structure. When a search in the global phone book is made by using the search function, only contacts matching the search tex...

  • Page 68

    Administrator settings 57 3.9.3.2 search the phone book can contain an unlimited amount of global contacts. Using search makes it easier to find the wanted contact. How to search in the global phone book: 1. Select the search icon. 2. Enter search text in the dialogue box that appears and press the ...

  • Page 69

    Tandberg 1000 mxp 58 3.9.3.3 copy contact to my contacts the copy contact to my contacts function is available from the placed calls, missed calls, received calls and global contacts folders, see phone book for details. It may be wise to copy contacts that are often used to my contacts. Note that th...

  • Page 70: 3.10 Camera Control

    Administrator settings 59 3.10 camera control manual focus the focus on the tandberg 1000 mxp can be adjusted manually by rotating the focus ring on the camera lens..

  • Page 71: 3.10.1

    Tandberg 1000 mxp 60 3.10.1 far end control far end control allows you to control your conference partner’s camera. An example of when this feature could be especially helpful is if it is not possible to see what a participant at the far end is writing on their white board. Use far end control to mo...

  • Page 72: 3.10.2 Picture

    Administrator settings 61 3.10.2 picture control brightness adjust brightness from 1-98 monitor brightness select monitor settings and adjust monitor brightness from 0-16.

  • Page 73: 3.11 Presentation

    Tandberg 1000 mxp 62 3.11 presentation the presentation functionality in the system enables you to show other available video sources in addition to your main camera. This is perfect for meetings where you would like to show a powerpoint presentation, for example. You can even use arrow keys up and ...

  • Page 74: 3.11.1

    Administrator settings 63 3.11.1 presentation key the quickest way to show a presentation is to use the presentation key on the remote control. The presentation key is used to start and stop a presentation. The presentation key will display pc (default*). When holding the presentation key for 1 seco...

  • Page 75: 3.11.2 Presentation

    Tandberg 1000 mxp 64 3.11.2 presentation menu the presentation menu offers you all available video sources; main camera, pc, document camera, vcr, aux and vnc. All these sources can be used as main video stream or dual video stream (duo video / h.239). Not all systems has all video sources available...

  • Page 76: 3.11.3

    Administrator settings 65 3.11.3 pc presenter (dvi/vga input) (optional feature - not available on all systems) users often have their presentations on a laptop that is brought into the meeting room. Remember to connect your pc to the codec before you press the presentation button. Note that the ima...

  • Page 77: 3.11.4

    Tandberg 1000 mxp 66 3.11.4 pc soft presenter and vnc (optional feature) pc softpresenter is used to display pc images on your system without using a vga cable (pc presenter). The system and your pc must be connected to the same lan. In addition, vnc (virtual network computing) server software must ...

  • Page 78: 3.11.5

    Administrator settings 67 3.11.5 dual stream (duovideo tf /h.239) (optional feature - not available on all systems) with dual stream you have the opportunity to show two different live video streams simultaneously, main video and one additional source. This is handy when showing a presentation. You ...

  • Page 79: 3.11.6

    Tandberg 1000 mxp 68 3.11.6 take new snapshot the system can take a snapshot of your live video. Snapshot is handy when you are in a call with a system that does not support dual stream. Use snapshot to show a snapshot of your presentation and continue the meeting with main camera. How to use snapsh...

  • Page 80: 3.11.7

    Administrator settings 69 3.11.7 display snapshot the system stores the last sent or received snapshot. The snapshot is deleted automatically after the call. How to display snapshots: 1. To view a stored snapshot, first choose the snapshot header. 2. Select display snapshot in the presentation menu....

  • Page 81: 3.12 Services

    Tandberg 1000 mxp 70 3.12 services a multipoint control unit (mcu) enables several sites to participate in the same conference. During an mcu conference, the status line will provide information about the conference. Services contain the following features: • request floor and release floor • confer...

  • Page 82

    Administrator settings 71 example of multisite for mid- to low end systems. Note that the illustrations may differ from the actual product. Using the system’s internal mcu, multisite tf * most tandberg mxp systems have an optional built-in mcu, which is called multisite*. It supports up to 6 video c...

  • Page 83

    Tandberg 1000 mxp 72 terminate meeting using an external mcu with limited chair control support you may have the following services with an external mcu that does not support h.243, you have the following services: request/release floor terminal names * the multisite option is not available on the t...

  • Page 84: 3.12.1

    Administrator settings 73 3.12.1 request floor and release floor when requesting floor, your video will be broadcasted in full screen to all other participants in the conference. Request floor is useful when you want to speak or display something in front of all participants. Release floor when you ...

  • Page 85: 3.12.2

    Tandberg 1000 mxp 74 3.12.2 conference layout (only supported by tandberg multisite*) with a tandberg multisite you can choose between the layouts: auto split, 4 split, 5+1 split and voice switched view. Auto split displays all participants on the screen simultaneously. 4 split displays the 4 last s...

  • Page 86: 3.12.3

    Administrator settings 75 3.12.3 terminal names choose terminal names to see a list of the participants of the multisite conference. Press cancel to go back..

  • Page 87: 3.12.4

    Tandberg 1000 mxp 76 3.12.4 chair control (not supported by tandberg mcu or multisite) as chairman, you have access to more multisite services. Select chair control to assume the role of chairman of the conference. Select release chair to end the role as chairman. A chair indicator appears when you ...

  • Page 88: 3.12.5

    Administrator settings 77 3.12.5 assign floor and release floor from participant assign floor allows the chairman to select which of the conference participants are to be broadcasted to all other participants..

  • Page 89: 3.12.6

    Tandberg 1000 mxp 78 3.12.6 view site and end view (not supported by tandberg mcu or multisite) view site allows you to view any participant in the conference regardless of who has the floor and chair. Choose end view to go back to normal..

  • Page 90: 3.12.7

    Administrator settings 79 3.12.7 disconnect participant disconnect participant allows the chairman to disconnect any participant in the conference. In a multipoint call, this is equivalent to disconnecting a participant from the end call menu..

  • Page 91: 3.12.8

    Tandberg 1000 mxp 80 3.12.8 terminate meeting terminate meeting allows the chairman to terminate the conference altogether. In a multisite call, this is equivalent to pressing end all calls from the end call menu..

  • Page 92: 3.12.9

    Administrator settings 81 3.12.9 more about multisite (embedded mcu) (optional feature*) calling in to a multisite any system can be part of a multisite conference by calling in to a multisite. The dial-in numbers to the multisite depends of the network that is used. To dial in to the multisite on i...

  • Page 93: 3.12.10   Text Chat

    Tandberg 1000 mxp 82 3.12.10 text chat while in an isdn or ip call to another system supporting text chat (t.140), select text chat the services menu. Enter text in the displayed window. How to use text chat: 1. Choose text chat from the services menu to open the text chat window. 2. Enter text with...

  • Page 94: 4 Control Panel

    Administrator settings 83 4 control panel the control panel contains the following features: user guide diagnostics audio demo restart settings* settings: general call quality security menu settings audio network presentation settings video restore default settings note: if administrator password is...

  • Page 95: 4.1  User Guide

    Tandberg 1000 mxp 84 4.1 user guide the on screen user guide takes you through a quick step-by-step introduction to the video system. It gives the user basic skills in how to use the system..

  • Page 96: 4.2 Diagnostics

    Administrator settings 85 4.2 diagnostics diagnostics allows testing of individual system components and displays the current system settings. Diagnostics contain: system information channel status call status system selftest view settings ip address conflict check warnings.

  • Page 97: 4.2.1 System

    Tandberg 1000 mxp 86 4.2.1 system information select system information to view system numbers, line status, software version, hardware serial number and other useful information. Press arrow key up and down to scroll in the system information list. System information contains: system name my isdn n...

  • Page 98: 4.2.2 Channel

    Administrator settings 87 4.2.2 channel status comprehensive information about the call progress is available through the channel status window. This window indicates the various stages each b-channel goes through whilst establishing a connection. Status - bri comments idle calling connected sync ac...

  • Page 99: 4.2.3 Call

    Tandberg 1000 mxp 88 4.2.3 call status comprehensive information about the call is available through the call status window. The menu has two columns, one for transmitted and one for received audio/video/data information. If dual stream or multisite is available on your system and in use, pressing t...

  • Page 100: 4.2.4 System

    Administrator settings 89 4.2.4 system selftest the system performs a check to determine internal hardware integrity. System selftest is useful when you want to check if your network connection is active..

  • Page 101: 4.2.5 View

    Tandberg 1000 mxp 90 4.2.5 view settings this window displays all the system settings. Use the arrow key on the remote control to scroll through the list. View settings may contain*: general settings system name language dual monitor auto answer max call length access code incoming mcu calls incomin...

  • Page 102

    Administrator settings 91 document camera vcr aux vnc split screen default call settings call type network bandwidth restrict (56k) auto h320 bandwidth auto h323 bandwidth sip audio settings inputs mic1 mic2 mic3 audio4 audio5 audio6 mix mode vcr ducking level settings mic1 mic2 mic3 audio4 audio5 a...

  • Page 103

    Tandberg 1000 mxp 92 brightness video name main cam aux doc cam vcr pc vga vnc network type isdn-bri\pri\leased e1\t1\external h331 isdn switch type etsi (euro isdn) line1 setup on number1 number2 spid1 spid2 line2 setup on number1 number2 spid1 spid2 line3 setup on number1 number2 spid1 spid2 advan...

  • Page 104

    Administrator settings 93 gateway ethernet speed dns settings h.323 settings e.164 alias use gatekeeper gatekeeper ip h.323 prefix advanced h.323 settings rsvp nat nat address qos ip precedence audio video data signaling ip type of service (tos) diffserv audio video data signaling ieee802.1x setting...

  • Page 105

    Tandberg 1000 mxp 94 data port 1 baud rate parity data bits stop bits mode data port 2 baud rate parity data bits stop bits mode * the settings available will vary within the mxp system range depending on system and what software options installed..

  • Page 106: 4.2.6

    Administrator settings 95 4.2.6 ip address conflict check the system will give a warning if there is an ip conflict. The user may initiate this check by selecting ip address conflict check..

  • Page 107: 4.2.7 Warnings

    Tandberg 1000 mxp 96 4.2.7 warnings any warnings registered by the system will be displayed in the warnings menu. Open a warning in the list to get more information about the warning. The following warnings may be displayed if detected by the system, depending on system type and configuration: isdn ...

  • Page 108

    Administrator settings 97 there is something wrong with the leased e1/t1 line (blue alarm). Please check your network connection. (192) there is something wrong with the leased e1/t1 line (yellow alarm). Please check your network connection. (193) h323 gatekeeper warnings could not register to the g...

  • Page 109: 4.3 Audio Demo

    Tandberg 1000 mxp 98 4.3 audio demo tandberg systems are designed to improve audio quality during a video conference – as if the person is in the same room! Demonstrate the high quality audio of your system by pressing the audio demo button at the bottom of the control panel menu. Lean back and enjo...

  • Page 110: 4.4 Restart

    Administrator settings 99 4.4 restart restart the system by pressing the restart button. You are prompted with a dialog box saying: do you want to restart the system? Press ok to restart, press cancel (x) to abort..

  • Page 111: 5  System Settings

    Tandberg 1000 mxp 100 5 system settings the control panel contains all the settings of the system. Making changes to the settings will change the behavior of the system. It is recommended to password protect the access to the settings to prevent occasional users from making crucial changes to the sy...

  • Page 112: 5.1 General Settings

    Administrator settings 101 5.1 general settings when installing the system, go through the general settings menu to ensure that you have the right settings for your system, see system configuration. General settings contain: language system name / international name * auto answer phone book settings...

  • Page 113: 5.1.1 Language

    Tandberg 1000 mxp 102 5.1.1 language the system supports 16 different languages for its on-screen menus; english, german, french, norwegian, swedish, italian, spanish, portuguese, russian, finnish, chinese simplified, chinese traditional, japanese, korean, thai and arabic. Select the preferred langu...

  • Page 114: 5.1.2 System

    Administrator settings 103 5.1.2 system name system name identifies the system: on the welcome page. During an mcu conference call. When using the web-interface. When the codec is acting as an snmp agent. Towards a dhcp server. H323 id. Other systems can call in using this name instead of ip-number/...

  • Page 115: 5.1.3 International

    Tandberg 1000 mxp 104 5.1.3 international name if the system name contains asian and non-latin character text input, the international name using latin characters only, must be specified as well. This is in order to make other systems understand the system name..

  • Page 116: 5.1.4 Auto

    Administrator settings 105 5.1.4 auto answer the auto answer setting decides whether an incoming call is put through automatically or manually. On the system will automatically answer all incoming calls. On+mic off the system will automatically answer all incoming calls and switch the microphone off...

  • Page 117: 5.1.5 Phone

    Tandberg 1000 mxp 106 5.1.5 phone book settings corporate directory on the corporate directory is available in the menu. Off the corporate directory is hidden from the menu and is unavailable for users. Ip address enter the ip address of the management system that provides the phone book. Path the p...

  • Page 118: 5.1.6

    Administrator settings 107 5.1.6 external services settings external services on when set to on external services are available. Off when set to off external services are unavailable. Ip address enter the ip address of the service provider for external services. Path enter the path to the external s...

  • Page 119: 5.1.7 Permissions

    Tandberg 1000 mxp 108 5.1.7 permissions permissions contains settings for incoming telephone calls, far end control, remote software upgrade and fallback to telephony. Access code an access code will help you control the use of the system. All users must enter a code to identify themselves and the c...

  • Page 120

    Administrator settings 109 fallback to telephony when dialing a number and the system fails to place a video call to the number dialed, the system will attempt to place a telephone call if fallback to telephony is enabled. On enables fallback from video calls to telephone calls. Off disables fallbac...

  • Page 121: 5.1.8 Screen

    Tandberg 1000 mxp 110 5.1.8 screen settings auto layout on if auto layout is on the system will change layouts automatically depending on the number of participants in a call and if you have a dual video stream or not. Please refer to layout for more information. Off if auto layout is off there will...

  • Page 122

    Administrator settings 111 picture in picture (pip) pressing the layout button on the remote will result in an extra picture in smaller view (picture in picture). Press the layout button to move it around in the corners of the screen and finally hide it. Pressing and holding layout for 1 second will...

  • Page 123

    Tandberg 1000 mxp 112 example of 1+2 picture outside picture (wide screen). Example of 1+3 picture outside picture (wide screen). Note that the following menu settings do not apply for all tandberg mxp systems. Please refer to the actual menu page on your system. Vga monitor format* to fully leverag...

  • Page 124

    Administrator settings 113 wide screen vga or tv monitor in normal (stretched) mode. Wide screen vga or tv monitor in wide (native) mode. Vga out quality* the supported range of vga formats will be optimized for the vga display monitor based on the source image. Vga out quality enables the user to c...

  • Page 125

    Tandberg 1000 mxp 114 vga out quality for wide xga: if vga monitor format is set to wide, pc picture format is set to normal, vga out quality is set to auto, the layout on the monitor is either full screen or pop, and the input source to the largest window is pc with resolution 1024x768, the system ...

  • Page 126: 5.1.9 Software

    Administrator settings 115 5.1.9 software options the system requires a valid option key to activate multisite and/or presenter functionality. In order to activate additional bandwidth, you need to enter a bandwidth key. A restart of the system is required after entering a new option and/or bandwidt...

  • Page 127: 5.1.10

    Tandberg 1000 mxp 116 5.1.10 date and time settings ntp ip this is the ntp time server address from which the system can get updated time information. See ip services for more details. Auto the ntp ip will be provided by the dhcp server. Manual the ntp ip address is set manually. Ip address the ip a...

  • Page 128: 5.2 Menu Settings

    Administrator settings 117 5.2 menu settings menu settings contain the settings: input editor language menu timeout in call balloon help number key mode administrator password kiosk mode settings startup icons.

  • Page 129: 5.2.1

    Tandberg 1000 mxp 118 5.2.1 input editor language when the input editor language is set to chinese, korean or japanese the user will be able to enter chinese / korean / japanese characters into an input field like the system name or phone book, using the remote control..

  • Page 130: 5.2.2

    Administrator settings 119 5.2.2 menu timeout in call the menu appears on the bottom line of the screen. Set menu timeout in call to on if you want the menu to time out automatically when you are in a call. On the menus will time out automatically after 15 seconds if there is no activity on the remo...

  • Page 131: 5.2.3 Balloon

    Tandberg 1000 mxp 120 5.2.3 balloon help it is possible to enable / disable the balloon help window. On choose on if you want help text windows to appear. Off there will be no help text window..

  • Page 132: 5.2.4

    Administrator settings 121 5.2.4 number key mode when pressing a number key on the remote control, while in a call, the user can decide what shall happen. The system can be configured to act automatic or manual. While in a call, the user presses a number key to: • add another call • dial extension n...

  • Page 133

    Tandberg 1000 mxp 122 settings for remote control number keys while in a call: add call while in a call, the call menu will automatically appear when a number key is pressed on the remote control. This will enable the user to add another call. Touch tones while in a call, the touch tones mode will a...

  • Page 134

    Administrator settings 123 if you have no stored presets on your system, you are likely not to use presets. Therefore the presets option is not present in the dialog box. Press arrow key to navigate in the list. Press ok on the remote control to select the desired entry. Press a number key while in ...

  • Page 135: 5.2.5

    Tandberg 1000 mxp 124 5.2.5 administrator password it is recommended to put an administrator password on the system. The administrator password can be maximum 5 digits long. The administrator password dialog box will pop up when you choose settings from the control panel. This will prevent occasiona...

  • Page 136: 5.2.6

    Administrator settings 125 5.2.6 kiosk mode settings kiosk mode in kiosk mode the system is set to a simplified state where it can be controlled with just the four arrow keys and ok. You will get a simplified on-screen menu with only basic functionality available: make calls (using predefined contac...

  • Page 137

    Tandberg 1000 mxp 126 if language menu is enabled you will first see the language selection menu. Select language and the welcome menu will be displayed with your desired language. In a call, the system will display far end video in full screen. If max call length is set to a value and the system is...

  • Page 138

    Administrator settings 127 kiosk mode - auto dial* on the system will automatically dial to the first contact in the phone book when he handset is lifted. If this contact is busy, the system will call the second number in the phone book and so on. If the user places the handset in the cradle, the sy...

  • Page 139: 5.2.7 Startup

    Tandberg 1000 mxp 128 5.2.7 startup welcome menu the welcome menu contains the menu, system status, your system name and dial in numbers. On the welcome menu is shown when the system wakes up from standby mode. Off the welcome menu is not shown when the system wakes up from standby mode. Press the o...

  • Page 140

    Administrator settings 129 off welcome text is not displayed on the welcome menu. Welcome text you can change the welcome text to any text you like, instead of the default text. Remember that display welcome text must be on to be able to edit the welcome text..

  • Page 141: 5.2.8 Icons

    Tandberg 1000 mxp 130 5.2.8 icons the following indicator icons may be set to on or off: mic off volume off on air encryption bad network telephone duovideo/h.239 see on-screen indicators for details..

  • Page 142: 5.3 Presentation Settings

    Administrator settings 131 5.3 presentation settings presentation settings contain: h.239 startup video source presentation source snapshot source auto-display snapshot pip placing presentation rate vnc settings.

  • Page 143: 5.3.1 Presentation

    Tandberg 1000 mxp 132 5.3.1 presentation start if your system has dual stream capabilities, you can show two video streams at the same time (see also dual stream ). Presentation start is auto by default. This means that you will start dual stream (a second video stream) automatically when starting a...

  • Page 144: 5.3.2 H.239

    Administrator settings 133 5.3.2 h.239 h.239 supports transmission of two video streams. It combines elements of duo video and people+content. If h.239 is disabled you will still be able to start tandberg dual video stream* enabled enables h.239 disabled disables h.239 * the tandberg 550 mxp can onl...

  • Page 145: 5.3.3

    Tandberg 1000 mxp 134 5.3.3 startup video source the startup video source is the video source on display when the system wakes up from standby mode. If you use main camera as start up source, the system will start with main camera every time the system wakes up from standby, regardless of what the p...

  • Page 146: 5.3.4 Presentation

    Administrator settings 135 5.3.4 presentation source the presentation source is connected to the presentation button on the remote. Pressing the presentation button will put the presentation source on display. Presentation source is pc by default*. You can change the presentation source to any video...

  • Page 147: 5.3.5 Snapshot

    Tandberg 1000 mxp 136 5.3.5 snapshot source when you take a snapshot, you get a snapshot of the snapshot source. Current is the default snapshot source. This means that you take a snapshot of the video source that is currently active. You can change the snapshot source to any video source. In this w...

  • Page 148: 5.3.6 Auto-Display

    Administrator settings 137 5.3.6 auto-display snapshot select auto to automatically display a received snapshot. Turn auto-display snapshot manual if you wish not to have them displayed on the screen when they are sent or received. The snapshots will be sent and received, but not displayed. With aut...

  • Page 149: 5.3.7 Pip

    Tandberg 1000 mxp 138 5.3.7 pip placing pip placing lets you decide where the pip shall appear. You can of course move the pip with the layout button on the remote anytime. Top right pip is placed in the top right corner. Bottom right pip is placed in the bottom right corner. Bottom left pip is plac...

  • Page 150: 5.3.8 Presentation

    Administrator settings 139 5.3.8 presentation rate when setting up a call with h.323 the bandwidth can be controlled by the user. The presentation rate is expressed in percent of the call rate and shall reflect the h.323 presentation rate settings of the sender. The settings are 25%, 50% and 75% of ...

  • Page 151: 5.3.9 Vnc

    Tandberg 1000 mxp 140 5.3.9 vnc settings vnc settings is necessary when using a vnc presentation. See chapter pc soft presenter and vnc for more information on how to use vnc. Address the ip-address of the pc with the vnc software installed. To find the ip- address of the pc, place the mouse pointer...

  • Page 152: 5.4 Call Quality

    Administrator settings 141 5.4 call quality call quality contains the settings: video algorithm audio algorithm max upstream rate video quality default call settings.

  • Page 153: 5.4.1 Video

    Tandberg 1000 mxp 142 5.4.1 video algorithm the system will automatically select the best video algorithm based on the video source and the capabilities of the remote system. Use this menu to disable video algorithms in case you have interoperability issues calling other systems. H.264 bandwidth eff...

  • Page 154: 5.4.2 Audio

    Administrator settings 143 5.4.2 audio algorithm the system will automatically select the best audio algorithm based on the call rate and the capabilities of the remote system. Use this menu to disable audio algorithms in case you want to remove “low quality” audio, or if you have interoperability i...

  • Page 155: 5.4.3

    Tandberg 1000 mxp 144 5.4.3 max upstream rate (kbps) the max upstream rate (kbps) defines the desired maximum transmitted call rate. This is to be able to limit the outgoing bandwidth whilst keeping the maximum incoming bandwidth, especially useful for home offices with different upstream and downst...

  • Page 156: 5.4.4 Video

    Administrator settings 145 5.4.4 video quality the different video sources need different video quality settings. Main camera, vcr, aux and split screen have motion as default. Pc, document camera and vnc have sharpness as default. Motion* optimized for smooth motion video (cif/sif or w288p for low ...

  • Page 157

    Tandberg 1000 mxp 146 sharpness*: improved quality of detailed images and graphics, lower frame rate, ideal for enhancing quality at lower bandwidths. 4cif will be used from a pal video input, digital clarity 4sif from ntsc, digital clarity w720p will be used from a wide format (hd720p) input vga/sv...

  • Page 158

    Administrator settings 147 native pal: 4cif (704 x 576 pixels), digital clarity 448p (576 x 448) icif (352 x 576 pixels), natural video cif (352 x 288 pixels) qcif (176 x 144 pixels) sqcif (128 x 96 pixels) native pc resolutions: xga (1024 x 768 pixels), digital clarity svga (800 x 600 pixels), digi...

  • Page 159: 5.4.5 Call

    Tandberg 1000 mxp 148 5.4.5 call settings default call settings are connected with call settings in the call menu. If you leave call settings unchanged when making a call, the system will use the default call settings in the call. In addition to the call settings call type, net, bandwidth and restri...

  • Page 160

    Administrator settings 149 bandwidth bandwidth decides the quality of the video picture. When set to auto the system will establish a connection using a proper bandwidth for the call, typically 384kbps for isdn calls and 768kbps for ip calls. When set to max the system will set up the call with maxi...

  • Page 161

    Tandberg 1000 mxp 150 sub-address is used to address different systems on the same isdn line and is primarily used in european countries. Lan equivalent extension address or tcs-4 is used to address different systems on a lan, when dialing via a gateway. To specify an isdn sub-address or its lan equ...

  • Page 162: 5.5 Audio

    Administrator settings 151 5.5 audio audio contains the settings: headset level settings alert tones and volume.

  • Page 163: 5.5.1

    Tandberg 1000 mxp 152 5.5.1 headset level settings headset mic it is possible to adjust the headset microphone input level according to the sensitivity of the used headset. The on-screen audio level indicator will make it easier to set the correct input level settings. The input level should be adju...

  • Page 164: 5.5.2

    Administrator settings 153 5.5.2 alert tones and volume video call alert tone and telephone alert tone to help distinguish between incoming video calls and ordinary telephone calls, it is recommended to use different ringing tones for video calls and telephone calls. Alert volume you may change the ...

  • Page 165: 5.6  Video

    Tandberg 1000 mxp 154 5.6 video video contains the settings: mcu status line web snapshots video name.

  • Page 166: 5.6.1

    Administrator settings 155 5.6.1 mcu status line on the mcu / duovideo indicator will be displayed and provide information about the conference. Off the mcu / duovideo indicator will not be displayed. Auto the mcu / duovideo indicator will be displayed for a few seconds and then timed out. When grab...

  • Page 167: 5.6.2 Web

    Tandberg 1000 mxp 156 5.6.2 web snapshots the system is able to generate jpeg snapshots and provide them when requested (as ‘http get’ or via ftp). See appendix 6 for descriptions of the possible snapshot files. On snapshots generation is enabled. Off snapshots generation is disabled. Note that web ...

  • Page 168: 5.6.3 Video

    Administrator settings 157 5.6.3 video name as a default, the video inputs are given the names main cam, pc, doc cam, vcr, aux or vnc, dependent on what video sources are available on your system. The video names cannot exceed eight characters. The names correspond to the video names in the presenta...

  • Page 169: 5.7 Security

    Tandberg 1000 mxp 158 5.7 security security contains the settings: encryption encryption mode passwords.

  • Page 170: 5.7.1 Encryption

    Administrator settings 159 5.7.1 encryption (country specific) auto the system will try to set up calls using encryption. Point to point calls: if the far end system supports encryption (aes or des), the call will be encrypted. If not, the call will proceed without encryption. Multisite calls*: in o...

  • Page 171: 5.7.2 Encryption

    Tandberg 1000 mxp 160 5.7.2 encryption mode auto the system will try to use the most secure encryption - aes, dependent on the capabilities of the other sites. For sites that do not support aes encryption, des encryption will be tried. Aes the system will try to use aes with 128 bits encryption when...

  • Page 172: 5.7.3 Passwords

    Administrator settings 161 5.7.3 passwords administrator password, ip access password, streaming password, vnc password, access code and remote software upgrade password are duplicated from their respective menus. Using the security menu gives you a quick way to change all passwords of the system..

  • Page 173: 5.8 Network

    Tandberg 1000 mxp 162 5.8 network the network menu contain: isdn-bri settings lan settings network profiles.

  • Page 174: 5.8.1 Isdn-Bri

    Administrator settings 163 5.8.1 isdn-bri settings to make sure your system will work properly using isdn-bri, make the following settings: 1. Set isdn switch type 2. Enter isdn line numbers (and spids, if required) 3. Disable unused lines some software versions do not support 6 isdn lines, therefor...

  • Page 175

    Tandberg 1000 mxp 164 advanced isdn settings sub address using a sub address enables you to connect up to eight isdn terminals to the same isdn telephone number and line. The terminals are addressed by using different sub addresses. To call a terminal with a sub address, separate the isdn telephone ...

  • Page 176: 5.8.2 Lan

    Administrator settings 165 5.8.2 lan settings lan settings contain: ip settings h.323 settings sip settings wireless lan settings snmp settings ip services quality of service 802.1x settings.

  • Page 177

    Tandberg 1000 mxp 166 5.8.2.1 ip settings remember to restart the system after making changes to ip settings. This can be done by selecting the “save and restart” at the bottom of the ip setting menu. Changes in ip settings menu will not have any effect until the system is restarted. Ip protocol ipv...

  • Page 178

    Administrator settings 167 ethernet speed auto the codec will auto-detect the speed/duplex on the lan. 10/half the codec will connect to the lan using 10mbps speed/half duplex. 10/full 10 mbps speed/full duplex. 100/half 100 mbps speed/half duplex. 100/full 100 mbps speed/full duplex. Ip access pass...

  • Page 179

    Tandberg 1000 mxp 168 dns settings dns server 1-5 dns server defines the network addresses for dns servers. Up to 5 addresses may be specified. If the network addresses are unknown, please contact your administrator or internet service provider. Dns domain name dns domain name is the default domain ...

  • Page 180

    Administrator settings 169 5.8.2.2 h.323 settings e.164 alias this is the e.164 address of the system. The e.164 address is equivalent to a telephone number, sometimes combined with access codes. Valid characters are 0-9,* and #. When using a gatekeeper, the system will send a message to the gatekee...

  • Page 181

    Tandberg 1000 mxp 170 gatekeeper settings gatekeeper discovery auto the system will automatically try to register to any available gatekeeper. If a gatekeeper responds to the request sent from the codec within 30 seconds this specific gatekeeper will be used. This requires auto discovery on the gate...

  • Page 182

    Administrator settings 171 multiple h.323 aliases is set to off. If set to off, the system will register a single h.323-ids on the gatekeeper based on the following priority: • h.323 id • international name • system name the default setting for multiple h.323 aliases is off..

  • Page 183

    Tandberg 1000 mxp 172 callmanager settings callmanager ip this is the callmanager ip-address that is used if you specify h.323 call setup: callmanager..

  • Page 184

    Administrator settings 173 advanced h.323 settings the advanced h.323 settings only have an effect if they are supported by your ip infrastructure. Nat nat, network address translation, is used when a pc and a videoconferencing system are connected to a router with nat support. Nat support in the vi...

  • Page 185

    Tandberg 1000 mxp 174 h.323 ports static when selecting static h.323 ports for tcp connections the ports 5555 to 5574 will be used for q.931 and h.245 respectively. Dynamic the system will allocate which ports to use when opening a tcp connection. The reason for doing this is to avoid using the same...

  • Page 186

    Administrator settings 175 5.8.2.3 sip settings mode on setting the sip mode to on will enable the system for incoming and outgoing sip calls. Off setting the sip mode to off will disable incoming and outgoing sip calls from the system. Display name the display name part of the sip address (uri) is ...

  • Page 187

    Tandberg 1000 mxp 176 server address the server address is the manually configured address for the outbound proxy and registrar. It is possible to use a fully qualified domain name, or an ip address. The default port is 5060 for tcp and udp, but another one can be provided. Server address: examples:...

  • Page 188

    Administrator settings 177 draft-ietf-avt-rfc2032-bis-06.Txt - draft for advanced video signaling including resolution and mpi. Rfc 2190 rtp payload format for h.263 video streams rfc 2429 rtp payload format for the 1998 version of itu-t rec. H.263 video (h.263+) draft-ietf-avt-rfc2429-bis-05.Txt - ...

  • Page 189

    Tandberg 1000 mxp 178 5.8.2.4 wireless lan settings ssid (service set identification) example “wlannetwork”. Defines a local network id for this wireless region. It must be the same for all end points and the access point. An endpoint will find the access point if the ssid is correct, however if the...

  • Page 190

    Administrator settings 179 use key select which of the keys shown below you want to use. Key 1-4 the 64-bit keys can consist of a leading star (*) and 5 characters. The 128-bit key can consist of a leading star (*) and 13 characters. Start with a * and then the text. Example: 128 bit key: *secretkey...

  • Page 191

    Tandberg 1000 mxp 180 5.8.2.5 snmp settings snmp settings snmp trap host identifies the ip-address of the snmp manager. Snmp (simple network management protocol, snmp ver 1) is used for monitoring and configuring of different entities in a network. The system's snmp agentresponds to requests from sn...

  • Page 192

    Administrator settings 181 5.8.2.6 ip services ntp ip this is the ntp time server address from which the system can get updated time information. This is a requirement for proper operation if h.235 authentication is implemented. The network time protocol (ntp) is used to synchronize the time of the ...

  • Page 193

    Tandberg 1000 mxp 182 5.8.2.7 quality of service qos type off no qos is used. Diffserv diffserv qos method is used. Please see below for details. Ip precedence ip precedence qos method is used. Please see below for details. Ip precedence video used to define which priority audio, video, data and sig...

  • Page 194

    Administrator settings 183 auto will provide the following priority: audio 4 diffserv video used to define which priority audio, video, data and signaling packets should have in an ip network. The priority ranges from 0 to 63 for each type of packets. Diffserv telephony used to define which priority...

  • Page 195

    Tandberg 1000 mxp 184 5.8.2.8 ieee 802.1x 802.1x the system may be connected to an ieee 802.1x lan network. Supported 802.1x protocols are eap-md5, eap-peap and eap-ttls. The 802.1x authentication are enabled by setting 802.1x mode to on. On 802.1x authentication enabled off 802.1x authentication di...

  • Page 196: 5.8.3 Network

    Administrator settings 185 5.8.3 network profiles this menu consists of 7 network profiles; a prefix and a suffix can be added for each profile. If you add a prefix/suffix to a profile, this prefix/suffix will automatically be added in front/back of the number being dialed. Example: 0 is added as a ...

  • Page 197: 5.8.4

    Tandberg 1000 mxp 186 5.8.4 restore default settings restore default settings will restore all system settings. Note that this will not affect your call directory information, network type, line setup numbers or your spid numbers. Note that when holding the headset / speaker button while turning on ...

  • Page 198: 6 Peripheral Equipment

    187 6 peripheral equipment using the optional peripheral devices outlined in this chapter and the many others available, you will be able to build your own applications for use with the system, thereby better integrating the system into your business environment. This chapter will explain how to con...

  • Page 199: 6.1 Interfaces

    Tandberg 1000 mxp 188 6.1 interfaces 6.1.1 video 1 video input 1 vga/dvi-i (dvi = digital video interface, i = integrated digital & analog) input, analog or digital. Vga formats supported on 'dvi-i in: svga (800x600) 60hz, 72hz, 75hz, 85hz xga (1024x768) 60 hz, 70hz, 75hz sxga (1280x1024) 60hz hd720...

  • Page 200

    Peripheral equipment 189 supported dvi cables: tandberg supports dvi-d single-link, dvi-a and dvi-i single-link format cables. Dvi-d cables transmit digital t.M.D.S. Signals, dvi-a cables transmit analog vga signals and dvi-i cables can transmit either digital or analog signals. It is possible to ex...

  • Page 201

    Tandberg 1000 mxp 190 the tandberg 6000 mxp profile and 3000 mxp profile* systems are shipped with a pc cable with integrated audio : dvi-a plug + 2*rca plug to vga plug + 3.5mm stereo plug, length 6m. Pc cable, vga - dvi with integrated audio signal name con. 3 pin con. 1 pin con. 5 pin con. 2 pin ...

  • Page 202

    Peripheral equipment 191 rgb return c5 6, 7, 8 rgb coax shield outer shield ground shell shell outer shield audio left centre tip audio black audio right ring centre audio red audio gnd gnd sleeve gnd audio shield pc cable, vga - dvi with integrated audio * applies to t3000 mxp profile with new hard...

  • Page 203

    Tandberg 1000 mxp 192 vga to dvi-a cable pinouts* : vga to dvi-a cable male-male 5m black, maximum length 5m. No item description 1 cable ul20276 3coax*30#+ip*28#+5c*28#+aeb black od:7.0mm l-5000mm 2 connector hdd 15p male black 3 connector hdd 17p male black 4 tube pe tube black od:1.5*10 / 1.0*15 ...

  • Page 204: 6.1.2 Audio

    Peripheral equipment 193 6.1.2 audio all audio inputs are active by default. For further information, refer to chapter audio . Headset 1 headset connector, 2.5mm 3-pole mini-jack. The headset plug must have the following configuration: tip: microphone output ring: earphone (receiver input) sleeve: c...

  • Page 205: 6.1.3 Network

    Tandberg 1000 mxp 194 6.1.3 network ethernet: 1 x ethernet (rj-45 jack) lan interface (10/100 mb) up to 768kbps to connect the system to a lan, use the ethernet cable provided by tandberg (or a standard ethernet cable). The cable specification is: 1 ------------ 1 2 ------------ 2 3 ------------ 3 6...

  • Page 206: 6.2 Document Camera

    Peripheral equipment 195 6.2 document camera a document camera can be used for showing text, diagrams and a variety of graphical material as well as small three-dimensional objects. How to use a document camera with your system: 1. Connect the document camera to the doc cam input, if available, on t...

  • Page 207: 6.3 Dvd / Vcr

    Tandberg 1000 mxp 196 6.3 dvd / vcr dvd/vcr playback mono for playback, connect a cable between video out on the vcr and video in (vcr) on the system. Connect a cable between audio out on the vcr and the audio in (vcr) on the system. Choose vcr from the presentation menu to activate the vcr input. M...

  • Page 208: 6.4 Additional Cameras

    Peripheral equipment 197 6.4 additional cameras extra fixed cameras you can connect extra fixed cameras to your system, for example, a whiteboard camera. Connect the video output of the additional camera to one of the available video inputs on the system. Note that additional controllable cameras ar...

  • Page 209: 6.5 Additional Microphones

    Tandberg 1000 mxp 198 6.5 additional microphones if your environment is such that you require more than one microphone for your room, e.G. You have a whiteboard at a distance from your table microphone, it is possible to connect additional microphones to your system. See appendix 4 for more informat...

  • Page 210: 6.6 The Tandberg Dnam and

    Peripheral equipment 199 6.6 the tandberg dnam and speakers tandberg 6000 mxp profile, tandberg 6000 mxp, tandberg 7000 mxp, tandberg 8000 mxp and tandberg maestro the tandberg digital natural audio module, dnam*: the dnam audiosystem is built on two specially designed and separate modules; the dnam...

  • Page 211

    Tandberg 1000 mxp 200 tandberg 6000 mxp profile dnam configuration center speakers + integrated stereo speakers the dnam amplifier*: 3 x 50w continuous average center output power (load specified by dnam center speakers). 2 x 50w continuous average stereo output power (load specified by tandberg lou...

  • Page 212

    Peripheral equipment 201 the dnam loudspeaker cabinet (center speakers)*: 3-way center speaker system frequency range 50hz - 20khz 2 x 130mm low- and midrange loudspeakers, 8 ohms nominal, high quality 1 x 25mm dome tweeter, 6 ohms nominal, high quality crossover filtered audio signals received from...

  • Page 213

    Tandberg 1000 mxp 202 the mini-dnam loudspeaker cabinet*: the mini-dnam speaker cabinet specification: 2 * 15w stereo speakers, high quality frequency range 100hz - 20khz enclosed mdf speaker cabinet integrated stereo speakers**: 2 * 15w stereo speakers, high quality frequency range 100hz - 20khz en...

  • Page 214: 6.7 Stereo Speaker Kit

    Peripheral equipment 203 6.7 stereo speaker kit note that the following applies only for systems with a stereo s/pdif output. The stereo speaker kit provides an pair of floor-standing loudspeakers in addition to the built-in dnam . Using these speakers will enable stereo functionality in your system...

  • Page 215

    Tandberg 1000 mxp 204.

  • Page 216: 6.8 Telephone Add-On

    Peripheral equipment 205 6.8 telephone add-on the system has a built in audio bridge* that can bring in voice over ip (voip) telephony or normal telephone sites using isdn. Note that this requires a system with mixed audio output (audio from local and far end) and one audio input without integrated ...

  • Page 217: 6.9 Dual Monitor

    Tandberg 1000 mxp 206 6.9 dual monitor note that this requires a system with dual monitor video output..

  • Page 218

    Peripheral equipment 207 6.10 xga monitors and projectors (optional) some tandberg systems can be delivered with optional single or dual tv/xga monitors. It can also be connected to any dvi/vga/pal or ntsc display. Note that this requires a system with minimum one dvi-i output..

  • Page 219: 6.11 Vesa Display Power

    Tandberg 1000 mxp 208 6.11 vesa display power management because of the tremendous amount of energy consumed by monitors when operating, the system will reduce power consumption and extend monitor lifecycle by suspending the (switch off) monitors and projectors when the system goes into sleep/standb...

  • Page 220: 6.12 Digital Monitor Power

    Peripheral equipment 209 6.12 digital monitor power management dmpm is monitor power management applied over the digital dvi interface. Tandberg supports dmpm in software f2 and above. Six monitor power states are defined. Monitor on power state transmitter (tandberg codec) and receiver (monitor) ar...

  • Page 221: Data (Edid)

    Tandberg 1000 mxp 210 6.13 extended display identification data (edid) extended display identification data (edid) is a vesa standard data format that will allow the system to communicate its capabilities, including vendor information like the supported vga- formats and frequency range limits to a p...

  • Page 222

    Peripheral equipment 211 tested and verified monitors, edid & timing listed below are some of the monitors tandberg have tested and verified against: adi a715 dell w1700 dell w1900 eizo l367 eizo f730 ergoscan 400s hitachi cm640et hitachi cm769et ibm 9494-hbo ibm g97 ibm e74 ibm 6743-60n jvc lt-23x4...

  • Page 223: 7 Appendices

    212 7 appendices appendices: appendix 1: technical specification appendix 2: bandwidth information appendix 3: environmental considerations appendix 4: guidelines for setting up rooms for video meetings appendix 5: security appendix 6: using the file system appendix 7: web interface appendix 8: conn...

  • Page 224: Technical Specification

    Appendices 213 appendix 1: technical specification technical specification unit delivered complete with: wireless remote control, built-in camera, microphone, speakers, cables, 12.1" lcd screen, table-top stand. Lcd screen wide view angle screen xga resolution auto or manual brightness bandwidth h.3...

  • Page 225

    Tandberg 1000 mxp 214 svga (800 x 600 pixels) vga (640 x 480 pixels) wide resolutions: w288p (512 x 288 pixels) w448p (768 x 448 pixels) receive only w576p (1024 x 576 pixels) w720p (1280 x 720 pixels) still image transfer cif, sif, 4cif (h.261 annex d), 4sif, vga, svga, xga audio standards g.711, g...

  • Page 226

    Appendices 215 intelligent packet loss recovery (iplr) h.245 dtmf tones in h.323 cisco callmanager integration using ecs ip address conflict warning date and time support via ntp call services ipv6 network support dual stack ipv4 and ipv6 simultaneous support net service support on ipv6: telnet, ssh...

  • Page 227: For Tandberg Endpoints

    Tandberg 1000 mxp 216 appendix 2: bandwidth information for tandberg endpoints bandwidth information for tandberg endpoints model 8000mxp, 7000mxp 6000mxp, maestro bandwidth point to point isdn / ip standard: 768 / 3072 option: 1920 / 4096 standard: 768 / 3072 option: 1920 / 4096 multisite total: 30...

  • Page 228

    Appendices 217 h.264 up to 2mbps up to 2mbps picture mode multisite vs, cp4, cp5+1 vs, cp4, cp5+1 model 990mxp / 990net mxp 880mxp / 880net mxp bandwidth point to point isdn / ip standard: 1920 (ip only) options: 512 / 1920 990net: 768 / 1920 standard: 1152 (ip only) option: 384 / 1152 multisite tot...

  • Page 229: Appendix 3: Environmental

    Tandberg 1000 mxp 218 appendix 3: environmental considerations environmental considerations this section explains how to carry out basic adjustments and simple tests to ensure that you send and receive the best possible image and audio quality when using your system. Iris control and lighting by def...

  • Page 230: Rooms For Video Meetings

    Appendices 219 appendix 4: guidelines for setting up rooms for video meetings guidelines for setting up rooms for video meetings the following are a set of guidelines to consider when either building a video meeting room, or using an existing room for video meeting. Lighting: low contrast desired fo...

  • Page 231

    Tandberg 1000 mxp 220 how to prepare a typical room for video meetings: the illustration below shows the principles of a typical room designed to obtain the best results when using a video meeting system. If the system has a separate microphone, it should be placed at the front of the table to ensur...

  • Page 232: Appendix 5: Security

    Appendices 221 appendix 5: security security the system has several features both to protect from unauthorized use and system access: access code: when access code is enabled, the user will be asked to enter an access code before he/she is able to make a call. The system will verify if the entered a...

  • Page 233

    Tandberg 1000 mxp 222 by setting an ip access password on the system, all access to the system using ip (telnet, ftp and web) requires a password. This password can be enabled from telnet or dataport using the command: ippassword . The default ip username and password is "tandberg". To remove this p...

  • Page 234

    Appendices 223 backwards compatibility) with extended diffie hellman key distribution via h.320, h.323 and leased line connections. The tandberg aes implementation is validated as conforming to the advanced encryption standard (aes) algorithm, as specified in federal information processing standard ...

  • Page 235: Using The File System

    Tandberg 1000 mxp 224 appendix 6: using the file system using the file system it is possible to access a file system within the tandberg system by using ftp: dos- window: ftp , or web- browser: ftp:// description of the different files: all.Prm all settings in the system (including directory) dir.Pr...

  • Page 236: Appendix 7: Web Interface

    Appendices 225 appendix 7: web interface web interface it is possible to access and maintain the system remotely via a local area network (lan) using a standard web-browser. Connect your system to a lan with a network cable. How to configure your system for web interface: 1. Opencontrol panel and ch...

  • Page 237: To Pri/t1

    Tandberg 1000 mxp 226 appendix 8: connecting the system to pri/t1 (not available on all tandberg systems) connecting the system to pri/t1 using csu adapter connecting the system to the isdn network via the e1/t1-interface using an adtran t1 esf csu ace or equivalent csu, will allow up to 1.54 mbps c...

  • Page 238: To The Switched 56 Network

    Appendices 227 appendix 9: connecting the system to the switched 56 network connecting the system to the switched 56 network using telesync ts-256 sw56/isdn adapter connecting the system to the sw56 network using a telesync adapter is described below. There are different telesync adapters for differ...

  • Page 239: Adapters

    Tandberg 1000 mxp 228 appendix 10: connecting the system to isdn using nt1 network adapters connecting the system to isdn using nt1 network adapters connecting connect the first isdn cable from isdn 1 on the system to the s-interface on your first nt1 network adapter. Connect the other isdn cables t...

  • Page 240

    Appendices 229.

  • Page 241: Tandberg Precision Hd Camera

    Tandberg 1000 mxp 230 appendix 11: tandberg cameras tandberg precision hd camera (available to tandberg 8000 mxp, 6000 mxp profile, 3000 mxp profile*, maestro mxp and edge 75/85/95 mxp) pin-outs and connectors 1. Extra camera in.

  • Page 242

    Appendices 231 2. 12v dc power in 3. Hd video out, hdmi** 4. Codec – hd video out 5. Kensington lock note! The enclosed tandberg camera cables must be used! Do not use other camera cables as this might cause problems with the transfer of video signals from the precision hd camera. 8-pin rj (shielded...

  • Page 243

    Tandberg 1000 mxp 232 the maximum length of the camera cable for multiple cameras supported by tandberg is 20 m (65 ft). * applies to t3000 mxp profile with new hardware. ** disabled when connected to a tandberg system using the tandberg camera cable. This output does not support hdcp (high bandwidt...

  • Page 244

    Appendices 233 top view:.

  • Page 245: Wave II Camera

    Tandberg 1000 mxp 234 (not available with tandberg 1000 mxp and set top systems) wave ii camera pinouts and connectors 8-pin rj (shielded modular jack): this connector is used for the power and control signals to the main camera. Pin-8 +12v (presence when connected in daisy chain) pin-7 gnd pin-6 gn...

  • Page 246

    Appendices 235 pin-5 gnd pin-4 rxd (in) pin-3 txd (out) pin-2 presence (+12v in daisy chain) pin-1 gnd.

  • Page 247

    Tandberg 1000 mxp 236 dimensions front view: side view: rear view: underside view:.

  • Page 248: Trc4)

    Appendices 237 appendix 12: remote control (trc3 / trc4) remote control (trc3 / trc4) the tandberg remote control transmits ir-signals using the following parameters: protocol siemens sda2208 reference frequency 485khz address 4 & 7 ir wavelength 940nm ir carrier frequency 30khz.

  • Page 249

    Tandberg 1000 mxp 238 remote control key code map: button codes remote control (trc 3) remote control (trc 4) tandberg tracker dec hex address button name address button name address button name 0 0 1 1 0 number 1 0 number 1 2 2 0 number 2 0 number 2 3 3 0 number 3 0 number 3 4 4 0 number 4 0 number...

  • Page 250

    Appendices 239 33 21 0 ok 0 ok 34 22 0 call 0 call 35 23 0 end call 0 end call 36 24 0 phone book 0 phone book 37 25 0 menu 0 menu 38 26 0 cancel 0 cancel 39 27 0 0 40 28 0 layout 0 layout 41 29 42 2a 0 main cam 43 2b 0 pc 44 2c 0 doc cam 45 2d 0 dvd 46 2e 0 aux 47 2f 0 help 4 p0 48 30 0 far end 4 p...

  • Page 251: Registration

    Tandberg 1000 mxp 240 appendix 13: cisco callmanager registration cisco callmanager registration configuring an h.323 client on the callmanager 4.0 the registration of a h.323 client in callmanager is supported on the callmanager (ccm) 4.0 software and forward. 1. To configure the callmanager with a...

  • Page 252: Diagnostic Tools For Ip

    Appendices 241 appendix 14: diagnostic tools for ip diagnostic tools for ip to use these tools, will require using a pc and setting up a telnet session towards the system. Q.931 to show q.931 trace during a call you need to issue the command ‘syslog on’. One can get traces for ras, q.931 and h.245 w...

  • Page 253

    Tandberg 1000 mxp 242 function port type gatekeeper discovery (ras) 1719 udp q.931 call setup 1720 tcp h.245 range 5555-5574 tcp video range 2326-2341 udp audio range 2326-2341 udp data/fecc range 2326-2341 udp point-to-point + duo video function port type gatekeeper discovery (ras) 1719 udp q.931 c...

  • Page 254: Appendix 15: System Upgrade

    Appendices 243 appendix 15: system upgrade system upgrade before starting the software upgrade of the tandberg mxp system, please make sure to have the new software file, (for instance s050000f30.Pkg) and the release key for this software available. Your tandberg partner will provide this for you. A...

  • Page 255

    Tandberg 1000 mxp 244 the following page will now be displayed: figure 1 3. Enter the release key in the ‘release key’ field and press the ‘install software’ button..

  • Page 256

    Appendices 245 a new page will now be displayed: figure 2 4. Type in the path to where the new software file is stored, or select the file by using the ‘browse’ button. 5. The progress for the sw upgrade can be tracked by pressing the ‘telnet’ link in the help text box before pressing the install bu...

  • Page 257

    Tandberg 1000 mxp 246 5. Type in your ip password (default is “tandberg”) as password. 6. Type ‘put and press enter. The new software file will now be uploaded to the tandberg mxp system. 7. When the software upload is complete, end the ftp connection to the tandberg mxp system by typing ‘bye’ in th...

  • Page 258

    Appendices 247 figure 3 5. Enter the release key for the system to be upgraded in the ‘release key’ field. If no release key is given, the far end system will use the previously stored release key if possible. This will work when upgrading from a main release to a dot release. 6 make sure the settin...

  • Page 259: Appendix 16: Declaration of

    Tandberg 1000 mxp 248 appendix 16: declaration of conformity ec declaration of conformity manufacturer: tandberg telecom as product name: tandberg 1000mxp type number: ttc7-12 description: video conferencing equipment this product complies with commission directives: lvd 73/23/eec emc 89/336/eec r&t...

  • Page 260: Protocols Supported

    Appendices 249 appendix 18: protocols supported protocols supported tcp/ip - transmission control protocol/internet protocol a set of networking protocols that provides connectivity over lan/wan to any network computer. Http - hypertext transfer protocol a protocol used to transfer information on th...

  • Page 261

    Tandberg 1000 mxp 250 wan – wide area network a communications network connecting geographically separated computers, printers, and other devices. Ssl - secure sockets layer ssl is a proposed open standard for establishing a secure communications channel to prevent the interception of critical infor...

  • Page 262

    Appendices 251 appendix 19: cable specifications tandberg mxp and classic endpoints that support external network external network pinout with respect to signals on the net port: • for balanced signals a “0”=low voltage is defined as terminal a positive with respect to terminal b. • for unbalanced s...

  • Page 263

    Tandberg 1000 mxp 252 cable specification v.35 cable tandberg mxp and classic endpoints that support external network • connector on cable at codec end: o female 26 pin high-density dsub with thumbscrews. • connectors on cable at v.35-adapter end: o male 34 pin winchester (amp part number 201357-1 o...

  • Page 264

    Appendices 253 cable specification v.35/rs-366 cable tandberg mxp and classic endpoints that support external network • connector on cable at codec end: o female 26 pin high-density dsub with thumbscrews. • connectors on cable at v.35-adapter end: o male 34 pin winchester (amp part number 201357-1 o...

  • Page 265

    Tandberg 1000 mxp 254 cable specification rs-449 cable tandberg mxp and classic endpoints that support external network • connector on tandberg end: o female 26pin high density dsub newark p/n 50f2055 or equivalent • connector on rs-449: o dsub 37 pin male signal name female 26pin dsub (tandberg end...

  • Page 266

    Appendices 255 cable specification rs-449/rs-366 cable tandberg mxp and classic endpoints that support external network • connector on tandberg end: o female 26pin high density dsub newark p/n 50f2055 or equivalent • connector on rs-449: o dsub 37 pin male • connector on rs-366: o dsub 25 pin male s...

  • Page 267

    Tandberg 1000 mxp 256 cable specification rs-530 cable tandberg mxp and classic endpoints that support external network • connector on tandberg end: o female 26pin high density dsub newark p/n 50f2055 or equivalent • connector on rs-530: o dsub 25 pin male • cable length: o 1 meter signal name femal...

  • Page 268

    Appendices 257 cable specification rs-530/rs-366 tandberg mxp and classic endpoints that support external network • connector on tandberg end: o female 26pin high density dsub newark p/n 50f2055 or equivalent • connector on rs-530: o dsub 25 pin male • connector on rs-366: o dsub 25 pin male • cable...

  • Page 269

    Tandberg 1000 mxp 258 cable specification rs-449 cable to kiv-7 tandberg mxp and classic endpoints that support external network • connector on tandberg end: o female 26pin high density dsub newark p/n 50f2055 or equivalent • connector on rs-449: o dsub 37 pin male signal name female 26pin dsub (tan...

  • Page 270: 8 Glossary

    259 8 glossary # 199 av1: external input for the tandberg/loewe monitor. 2nd monitor: the second monitor of your videoconferencing system. The second monitor is normally placed on the right side of the first monitor. 4cif: 4 times cif, 704x576 pixels 4sif: 4 times sif, 704x480 pixels a aacld: advanc...

  • Page 271

    Tandberg 1000 mxp 260 b bandwidth: decides the quality of the video call. High bandwidth gives high quality. C call control data triggered: uses txdata, rxdata and clock signals only. Use data triggered when no handshake signal is available. Call control leased line: is a non-dialing protocol and sh...

  • Page 272

    Glossary 261 diagnostics: allows testing of individual system components and displays the current system settings. Digital claritytf: participants enjoy presentations of exceptionally high quality resolution video. Disconnect site: as a chairman, you get the option disconnect site. Disconnect site a...

  • Page 273

    Tandberg 1000 mxp 262 g g.711: audio algorithm for normal quality audio (telephone quality, 3.1 khz) the system will always have g.711 enabled. G.722: audio algorithm for high quality audio (7 khz). G.722.1: audio algorithm for compressed high quality audio (7 khz) g.728: audio algorithm for compres...

  • Page 274

    Glossary 263 m main camera: your camera. Video input 1 max call length: this feature will automatically end both incoming and outgoing calls when the call time exceeds the length specified. Max channels: indicates the maximum number of channels the system is allowed to use on the e1/t1 interface. Mc...

  • Page 275

    Tandberg 1000 mxp 264 network profiles: it is possible to define up to 6 network profiles, each consisting of name and call prefix, and 3 of them also include network selection. Non standard facility: the network provider may require service selection in your isdn configuration. Valid nsf codes are ...

  • Page 276

    Glossary 265 request floor: the mcu will broadcast the video in full screen to all other participants in the conference. If the mcu conference has a chairman, a request will be sent to the the chairman. Restart: restarts the system. Restore defaults: restores system settings to the factory defaults....

  • Page 277

    Tandberg 1000 mxp 266 streaming announcements: the system will announce to the network that it is streaming. This enables a streaming client (e.G. A pc) to connect to the system's streaming session. Used by cisco ip/tv. Streaming password: prevents unauthorized access to the streaming functionality....

  • Page 278

    Glossary 267 vnc: virtual network computing. Voice switched: the active site will be displayed in full screen during a multisite conference. W wave ii camera: wide angle view camera - delivers the widest angle of view in the industry. Welcome menu: the welcome menu displays the menu when you are out...

  • Page 279: 9 Index

    Tandberg 1000 mxp 268 9 index a access code......................................86, 108 additional microphone .............................198 administrator password...........................124 alert speaker ...........................................153 alert tones and volume ......................

  • Page 280

    Index 269 snapshot source .....................................136 software options .....................................115 start up video source .............................134 system configuration .................................12 system information....................................86 system...