Www.U-lineservice.Com phone (414) 354-0300 • fax (414) 354-7905 service & parts tech lines phone (800) 779-2547 • fax (414) 354-5696 onlineservice@u-line.Com ©2005 u-line corporation 02/2005 bi-98 ice maker installation guide.
Www.U-lineservice.Com 2 02/2005 bi-98 ice maker contents exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 cut-out dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 product dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 door swing/...
02/2005 3 www.U-lineservice.Com bi-98 ice maker general precautions use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: warning shock hazard — electrical grounding required. • keep the unit unplugged throughout installa...
Www.U-lineservice.Com 4 02/2005 bi-98 ice maker your u-line product has been designed for either free- standing or built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must not be obstructed and clearance is required ...
02/2005 5 www.U-lineservice.Com bi-98 ice maker reversing the door all units may be left- or right-hand opening. Note: the grille should not yet be installed. If it has been installed, remove it for door reversing. See page 10. To reverse the door: 1. Remove top hinge from cabinet (three screws). Se...
Www.U-lineservice.Com 6 02/2005 bi-98 ice maker 10. Fasten upper hinge to unit (three screws). Partially tighten screws. See figure 11. 11. Adjust door to assure proper seal. Tighten upper and lower hinge screws securely. 12. Replace three plastic plugs removed in step 8 into holes on top of unit. R...
02/2005 7 www.U-lineservice.Com bi-98 ice maker 2. Pull door gasket out of groove (top edge of door only). Start in the middle and pull outward, moving toward the edge (see figure 13). This may take some force. 3. Remove two outside screws holding door handle. Slightly separate door handle from door...
Www.U-lineservice.Com 8 02/2005 bi-98 ice maker caution plumbing installation must observe all state and local codes. All water connections must be made by a licensed/ qualified plumbing contractor. Failure to follow recommendations and instructions may result in damage and/or harm. Warning to preve...
02/2005 9 www.U-lineservice.Com bi-98 ice maker electrical specifications caution electrical installation must observe all state and local codes. This unit requires connection to a grounded (three- prong), polarized receptacle that has been placed by a qualified electrician. The unit requires a grou...
Www.U-lineservice.Com 10 02/2005 bi-98 ice maker installation of the bi-98 1. Open the water supply valve in the main water source. 2. Plug in the power cord. 3. Gently push the unit into position. Be careful not to kink the water supply line or entangle the electrical cord. 4. Re-check the leveling...
02/2005 11 www.U-lineservice.Com bi-98 ice maker initial start-up the on/off switch is located behind the front grille. A small opening in the top of the grille is provided to access the switch. Ensure that the switch is turned on. No setting adjustments should be necessary at this time. For informa...
?2005 u-line corporation publication no. 30066e 02/2005 u-line corporation, located in milwaukee, wi, is a family operated manufacturer of built-in undercounter icemakers, combo ® icemaker/refrigerators, wine captain ® wine storage units, refrigerators, refrigerated drawers and refrigerator/freezers...
