Www.U-lineservice.Com phone (414) 354-0300 • fax (414) 354-7905 service & parts tech lines phone (800) 779-2547 • fax (414) 354-5696 onlineservice@u-line.Com ©2006 u-line corporation 08/2006 bi-2115 — ice maker installation guide.
Bi-2115 — ice maker www.U-lineservice.Com 2 08/2006 contents exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 cut-out dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 product dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 door sw...
Bi-2115 — ice maker 08/2006 3 www.U-lineservice.Com general precautions use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: warning shock hazard — electrical grounding required. • keep the unit unplugged throughout inst...
Bi-2115 — ice maker www.U-lineservice.Com 4 08/2006 after all the protective coating has been removed from the unit/door, clean all stainless steel surfaces with claire stainless steel polish and cleaner or comparable product or a mild detergent and warm water solution and soft cloth. Do not use abr...
Bi-2115 — ice maker 08/2006 5 www.U-lineservice.Com product dimensions please note that the unit has adjustable feet that can add one additional inch to height during leveling or to match adjacent cabinets (see figure 36 on page 14). Door swing/clearances information black and white units have a zer...
Bi-2115 — ice maker www.U-lineservice.Com 6 08/2006 4. Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge (see figure 8). 5. Remove existing bottom hinge (3 screws) and remount on opposite side top. Remove hinge screw pin. 6. Remove the pla...
Bi-2115 — ice maker 08/2006 7 www.U-lineservice.Com side-by-side installation instructions for a complete refreshment center, install your bi2115 ice maker beside a u-line refrigerator, combo, or wine captain model (see figure 11 for typical cut-out). Note that each side-by-side installation will be...
Bi-2115 — ice maker www.U-lineservice.Com 8 08/2006 2. Pull door gasket out of groove (top edge of door only). Start in the middle and pull outward, moving toward the edge (see figure 13). This may take some force. 3. Remove two outside screws holding door handle. Slightly separate door handle from ...
Bi-2115 — ice maker 08/2006 9 www.U-lineservice.Com 2. Create a relief (figure 15) for pivot plate by cutting notch in top corner of overlay panel. Refer to figure 16 for exact specifications. Route notch in top corner of overlay panel as shown (see top and side views). Top of notch is entire depth ...
Bi-2115 — ice maker www.U-lineservice.Com 10 08/2006 3. Attach the door panel to the overlay panel using #10 x 5/8" wood screws and nylon spacers. The nylon spacers fit between the overlay panel and the door panel as shown in figure 21. The spacers allow the original door panel to slide back into th...
Bi-2115 — ice maker 08/2006 11 www.U-lineservice.Com 4. Attach top pivot plate to door handle, on side where hinges will be. Use the two #8-32 x 1/2" flat head phillips screws (black) supplied with kit (see figure 24). 5. Starting at the corners and working toward the center, push the door gasket ba...
Bi-2115 — ice maker www.U-lineservice.Com 12 08/2006 checking door alignment the unit’s door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment or during door panel installation. Important properly aligned, the door should be 1/8" below the to...
Bi-2115 — ice maker 08/2006 13 www.U-lineservice.Com caution plumbing installation must observe all state and local codes. All water connections must be made by a licensed/ qualified plumbing contractor. Failure to follow recommendations and instructions may result in damage and/or harm. Warning to ...
Bi-2115 — ice maker www.U-lineservice.Com 14 08/2006 electrical specifications caution electrical installation must observe all state and local codes. This unit requires connection to a grounded (three- prong), polarized receptacle that has been placed by a qualified electrician. The unit requires a...
Bi-2115 — ice maker 08/2006 15 www.U-lineservice.Com installation of the bi2115 1. Open the water supply valve in the main water source. 2. Make sure the on/off switch is in the off position (see figure 37). 3. Plug in the power cord. 4. Gently push the unit into position. Be careful not to kink the...
Bi-2115 — ice maker www.U-lineservice.Com 16 08/2006 start-up troubleshooting problem q: unit does not appear to turn on when switch is set to on. Solution a: make sure unit is plugged in and outlet has power (circuit breaker has not tripped). Remember that the ice maker mechanism will not fill the ...
©2006 u-line corporation publication no. 30145e 08/2006 rev. B u-line corporation, located in milwaukee, wi, is a family operated manufacturer of built-in undercounter icemakers, combo ® icemaker/refrigerators, wine captain ® wine storage units, refrigerators, refrigerated drawers and refrigerator/f...
