U-Line Echelon Wine Captain 2275ZWCOL Installation Manual - page 3
03/2008
3
www.U-LineService.com
2275 Dual Zone WC Model
Inspect and Plan
You have received a carton containing your 2275ZWC or
2275ZWCOL with a package inside containing a Use and
Care Guide and a Product Registration Card and an Anti-
Tip Bracket installation kit 2275ZWCOL units are shipped
with an additional package of hardware. Complete and
mail the Product Registration Card or register online at
www.U-LineService.com. Once your unit is installed, keep
the Use and Care Guide and this Installation Guide in a
safe place for future reference.
2275ZWC units are stainless steel. Stainless steel units are
covered with a protective coating and have been ordered
left- or right-hand hinged. The stainless doors are not
reversible.
2275ZWCOL units are black with a door that requires the
construction of a 3/4” thick wood overlay frame. You must
determine left- or right-hand opening before
construction.
All units come with maple trim racks that can be finished
or stained. Please carefully follow the directions that
apply to your unit and your intended design.
TOOLS/MATERIALS REQUIRED
• Screwdrivers — slotted and Phillips head
• Sandpaper; low odor, water clean up, quick drying
finish; tack cloth and, if desired, water-based wood
stain and synthetic foam brush.
• 3/4” overlay frame material, cutting tools, drill and bits
(2275ZWCOL units).
INSPECTION
Unwrap and inspect the unit on a flat, level surface
capable of supporting its entire weight.
REMOVING PROTECTIVE COATING
(Stainless Steel units only)
When inspecting/installing a stainless steel unit, the
protective coating covering the unit must be removed
first. Start at a corner of the unit/door and pull back the
protective coating to remove it from the unit/door.
After all the protective coating has been removed from
the unit/door, clean all stainless steel surfaces with Claire
Stainless Steel Polish and Cleaner or comparable product,
or a mild detergent and warm water solution and soft
cloth. DO NOT use abrasive cleaning agents.
Note: If cleaning with mild detergent and warm water
solution and soft cloth, the unit MUST be treated with
Claire Stainless Steel Polish and Cleaner or comparable to
prevent discoloration.
EXTERIOR CLEANING
(As Required)
Overlay Models:
• The door, grille and cabinet may be cleaned with a mild
detergent and warm water solution. Do not use
solvent-based or abrasive cleaners. Use a soft sponge
and rinse with clean water. Wipe with a soft, clean
towel to prevent water spotting.
Stainless Surfaces:
• Stainless door panels, handles and frames can discolor
when exposed to chlorine gas, pool chemicals, salt
water or cleaners with bleach.
• Clean any glass door fronts with a non-chlorine glass
cleaner.
• Keep your Stainless unit looking new by cleaning with
a good quality all-in-one stainless steel cleaner/polish
on a monthly basis. For best results use Claire Stainless
Steel Polish and Cleaner, which can be purchased from
U-Line Corporation. (The part number is 173348.)
Comparable products are acceptable. Frequent
cleaning will remove surface contamination that could
lead to rust. Some installations may require cleaning
on a weekly basis.
• Do not clean with steel wool pads.
• Do not use stainless steel cleaners/polishes on
any glass surfaces.
• Do not use cleaners that are not specifically
intended for stainless steel on stainless surfaces
(this includes glass, tile and counter cleaners).
• If any surface discolors or rusting appears, clean it
quickly with Bon-Ami or Barkeepers Friend Cleanser
and a non-abrasive cloth. Always clean in the direction
of the grain. Always finish this process with Claire
Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
• Use of abrasive pads such as Scotchbrite will
cause the graining in the stainless to become
blurred.
• Rust that is allowed to linger can penetrate into the
surface of the stainless steel and complete removal of
the rust may not be possible.
2 Inspect and Plan