- DL manuals
- U-Line
- Refrigerator
- U-3018CLROL-00
- Install Manual
U-Line U-3018CLROL-00 Install Manual
Summary of U-3018CLROL-00
Page 1
® the built-in undercounter leader since 1962 u-line.Com install guide modular 3000 series 120v, 3018clr models u-3018clrol-00 u-3018clrol-01 u-3018clrol-40 u-3018clrol-41 u-3018clrs-00 u-3018clrs-01 u-3018clrs-40 u-3018clrs-41.
Page 2
1 - safety precautions safety alert definitions.........................................................................................................................................1 general precautions .................................................................................................
Page 3
U-line safety precautions 1 ice machines notice • please read all instructions before installing, operating, or servicing the appliance. • proper installation procedures must be followed when completing an installation or relocation of a unit. An installation guide for the unit, providing complete i...
Page 4
Installation guide 2 ice machines product registration you have received a carton containing your 3000 series unit with a package inside containing a quick start guide and a registration card. Please complete and mail the product registration card. You may also register the unit online at u-line.Com...
Page 5
Installation guide 3 ice machines your u-line product has been designed exclusively for a built-in installation. When built-in, your unit does not require additional air space for top, sides, or rear. However, the front grille must not be obstructed and clearance is required for an electrical connec...
Page 6
Installation guide 4 ice machines 3018 series 4 product dimensions 33-11/16" to 34-11/16" 23-1/4" 17-3/4" solid overlay door 3-5/8" to 4-5/8" 3-5/8" to 4-5/8" 33-11/16" to 34-11/16" 24" stainless steel solid door 17-3/4".
Page 7
Installation guide 5 ice machines units have a zero clearance when the door to open 90°. Overlay models will need additional space for any knobs or pulls installed on the overlay panel / frame. Stainless steel models require 2" door clearance to accommodate the handle if installed next to a wall. Ot...
Page 8
Use & care guide 6 ice machines door alignment and adjustment align and adjust the door if it is not level, or is not sealing properly. If the door is not sealed the unit may not cool properly, or excessive frost or condensation may form in the interior. Notice properly aligned, the door’s gasket sh...
Page 9
Installation guide 7 ice machines overlay / frame overlay panel notice due to differences in surrounding cabinetry the panel may not perfectly align with door. The procedure below is designed to provide a finished overlay panel that seamlessly integrates with surrounding cabinetry. Panel preparation...
Page 10
Installation guide 8 ice machines notice make certain the display cable remains securely seated in the inner door channel, see below. 5. The frame should be aligned with the outside edge (opposite the hinge) and high enough to align with the highest point in the door. Notice due to differences in fl...
Page 11
Installation guide 9 ice machines overlay grille the 3000 series grille is fully adjustable and can be set to match your surrounding cabinetry dimensions. In addition to it’s adjustability, an overlay may also be installed to truly provide a seamless appearance. Prepare and install overlay 1. Use th...
Page 12
Installation guide 10 ice machines anti-tip brackets installation warning ! The anti-tip bracket must be installed to prevent the unit from tipping when doors are fully opened, or excess weight is placed on the front of the unit. The anti-tip brackets have multiple mounting choices depending on your...
Page 13
Installation guide 11 ice machines 9 leveling information it is recommended that the unit is level once installed. 6. Use a level to check the levelness of the unit from front to back and from side to side. Level should be placed along top edge and side edge as shown. 7. If the unit is not level, re...
Page 14
Installation guide 12 ice machines the unit requires a 1/4" o.D. Soft copper supply line, or flexible water supply kit from u-line (part no. Waterhookup). Warning ! Prior to attempting installation, determine if this product contains a gravity style drain or factory installed drain pump. Products wi...
Page 15
Installation guide 13 ice machines compression nut and ferrule onto the copper tubing as shown below. 9. Feed the complete assembly into the garden fitting and tighten. Attach to the water valve located in the front of the unit. 10. Gray hooks are located in the front of the condenser and behind the...
Page 16
Installation guide 13 ice machines the 3018clr requires access to either a gravity or pump fed drain. Caution ! If your u-line unit did not come with a factory installed drain pump you must use a gravity style drain connection. For assistance in determining if your unit has a pump please contact u-l...
Page 17
Installation guide 14 ice machines notice the maximum lift for the p60 drain pump is 10 feet. This must be done as close to the rear of the unit as possible. Notice before installing your u-line 3018clr with factory-installed u-line p60 pump, it is extremely important to check and test all hose conn...
Page 18: Installation Guide
® u-line.Com installation guide ©2012 u-line corporation publication number 30385 08/2012 rev a the built-in undercouter leader since 1962 product information complete installation guides, use and care guides, specifications & features and benefits, cad drawings, overlay panel/frame and toe-kick spe...