1. DL manuals
  2. Vacon
  3. Controller
  4. 10
  5. Quick Manual

Vacon 10 Quick Manual

Summary of 10

  • Page 1

    Vacon ® 10 ac drives quick guide.

  • Page 3

    Safety vacon • 1 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 1 this quick guide includes the steps that enable you to easily install and setup your vacon 10 frequency converter. Before putting your drive into operation, download and read the complete vacon 10 user manual from www.Va...

  • Page 4

    2 • vacon safety tel. +358 (0)201 2121 • fax +358 (0)201 212205 1 note: english and french product manuals with applicable information on safe- ty, warnings, and cautions can be downloaded from www.Vacon.Com/down- loads . Remarque vous pouvez télécharger les versions anglaise et française des manuel...

  • Page 5

    Installation vacon • 3 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 2 2. Installation 2.1 mechanical installation there are two possible ways to mount vacon 10 on the wall, either by screw or din rail mounting. Figure 2.1: screw mounting, mi1 - mi3 figure 2.2: din rail mounting, mi1 ...

  • Page 6

    4 • vacon installation tel. +358 (0)201 2121 • fax +358 (0)201 212205 2 . Figure 2.3: attaching the pe plate and api cable support, mi1 - mi3 attach this plate before installing the power cables attach the support after installing the power cables.

  • Page 7

    Installation vacon • 5 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 2 2.2 cabling and connections 2.2.1 power cabling note: the tightening torque for power cables is 0.5 - 0.6 nm (4-5 in-lbs). Figure 2.4: vacon 10 power connections, mi1 figure 2.5: vacon 10 power connections, mi2 - m...

  • Page 8

    6 • vacon installation tel. +358 (0)201 2121 • fax +358 (0)201 212205 2 2.2.2 control cabling figure 2.6: open the lid (mi1 - mi3) figure 2.7: install the control cables (mi1 - mi3) strip the plastic cable coating for 360°earthing control cable tightening torque: 0.4 nm.

  • Page 9

    Vacon 10 api vacon • 7 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 3 3. Control i/o and terminals figure 3.1: vacon 10 i/o terminal signal factory preset description 1 +10vref ref. Voltage out maximum load 10 ma 2 ai1 analog signal in 1 freq. Reference p) 0 - 10 v, ri = 300 kΩ (min)...

  • Page 10

    8 • vacon navigation & startup tel. +358 (0)201 2121 • fax +358 (0)201 212205 4 4. Navigation and startup 4. 1 the main menus of vacon 10 figure 4.1: the main menu of vacon 10 f w d r ev i/o k ey pa d b u s re f m on pa r sys sys sys sys sys sys sys sys fa ult a l ar m s to p r e ad y r u n f w d r ...

  • Page 11

    Navigation & startup vacon • 9 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 4 4.2 putting into operation and startup wizard 4.2.1 steps to put the drive into operation: 4.2.2 startup wizard vacon 10 runs the startup wizard when the machine is powered up for the first time. The wizard...

  • Page 12

    10 • vacon navigation & startup tel. +358 (0)201 2121 • fax +358 (0)201 212205 4 figure 4.2: vacon 10 startup wizard (standard application) fau lt alarm sto p ready run ref mon par sys fau lt alarm s to p ready run ref mon par sys fau lt alarm s to p ready run ref mon par sys fwd rev i/o key pad bus...

  • Page 13

    Navigation & startup vacon • 11 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 4 figure 4.3: drive setup 1 2 3 4 selections: parameters affected: p1.7 current limit (a) p1.8 motor control mode p1.15 torque boost p2.2 start function p2.3 stop function p3.1 min frequency p4.2 acc. Time (...

  • Page 14

    12 • vacon monitoring & parameters tel. +358 (0)201 2121 • fax +358 (0)201 212205 5 5. Monitoring & parameters note: this guide is for vacon 10 standard application, if you need description of parameters in detail, please download the application manual on: www.Vacon.Com -> downloads. 5.1 monitoring...

  • Page 15

    Monitoring & parameters vacon • 13 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 5 5.2 quick setup parameters (virtual menu; displays when par. 17.2 = 1) code parameter min max unit default id note motor nominal voltage 180 690 v varies 110 check rating plate on motor motor nominal fr...

  • Page 16

    14 • vacon monitoring & parameters tel. +358 (0)201 2121 • fax +358 (0)201 212205 5 acceleration time 1 0,1 3000,0 s 3,0 103 acceleration time from 0 hz to maximum fre- quency. Deceleration time 1 0,1 3000,0 s 3,0 104 deceleration time from maximum frequency to 0 hz. P6.1 ai1 signal range 0 1 0 379 ...

  • Page 17

    Monitoring & parameters vacon • 15 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 5 5.3 motor settings (control panel: menu par -> p1) code parameter min max unit default id note motor nominal voltage 180 690 v varies 110 check rating plate on motor motor nominal fre- quency 30,00 320,...

  • Page 18

    16 • vacon monitoring & parameters tel. +358 (0)201 2121 • fax +358 (0)201 212205 5 note: these parameters display when p17.2 = 0. Motor identifica- tion 0 1 0 631 0 = not active 1 = standstill identification (need run command within 20 s to activate) rs voltage drop 0,00 100,00 % 0,00 662 voltage d...

  • Page 19

    Monitoring & parameters vacon • 17 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 5 5.4 start/stop setup (control panel: menu par -> p2) 5.5 frequency references (control panel: menu par -> p3) note: these parameters display when p17.2 = 0. Code parameter min max unit default id note p...

  • Page 20

    18 • vacon monitoring & parameters tel. +358 (0)201 2121 • fax +358 (0)201 212205 5 5.6 ramp and brake setup (control panel: menu par -> p4) code parameter min max unit default id note ramp s-shape 0,0 10,0 s 0,0 500 0 = linear >0 = s-curve ramp time acceleration time 1 0,1 3000,0 s 3,0 103 defines ...

  • Page 21

    Monitoring & parameters vacon • 19 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 5 5.7 digital inputs (control panel: menu par -> p5) 5.8 analog inputs (control panel: menu par -> p6) code parameter min max unit default id note p5.1 i/o control signal 1 0 6 1 403 0 = not used 1 = di1 ...

  • Page 22

    20 • vacon monitoring & parameters tel. +358 (0)201 2121 • fax +358 (0)201 212205 5 5.9 digital outputs (control panel: menu par -> p8) 5.10 analog outputs (control panel: menu par -> p9) code parameter min max unit default id selections p8.1 ro1 signal selection 0 11 2 313 0 = not used 1 = ready 2 ...

  • Page 23

    Monitoring & parameters vacon • 21 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 5 5.11 protections (control panel: menu par -> p13) note: these parameters are shown when p17.2 = 0. 5.12 fault autoreset parameters (control panel: menu par -> p14) note: these parameters are shown when ...

  • Page 24

    22 • vacon monitoring & parameters tel. +358 (0)201 2121 • fax +358 (0)201 212205 5 5.13 pi control parameters (control panel: menu par -> p15) note: these parameters are shown when p17.2 = 0. 5.14 application setting (control panel: menu par -> p17) code parameter min max unit default id note p15.1...

  • Page 25

    Monitoring & parameters vacon • 23 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 5 5.15 system parameters code parameter min max default id note software information (menu sys -> v1) v1.1 api sw id 2314 v1.2 api sw version 835 v1.3 power sw id 2315 v1.4 power sw version 834 v1.5 appli...

  • Page 26

    24 • vacon monitoring & parameters tel. +358 (0)201 2121 • fax +358 (0)201 212205 5 p2.8 reset communication status 0 1 0 815 other information v3.1 mwh counter 827 million watt hour v3.2 power on days 828 v3.3 power on hours 829 v3.4 run counter: days 840 v3.5 run counter: hours 841 v3.6 fault coun...

  • Page 27: 111

    Fault tracing vacon • 25 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 6 6. Fault tracing fault code fault name fault code fault name 1 overcurrent 25 microcontroller watchdog fault 2 overvoltage 27 back emf protection 3 earth fault 29 thermistor fault 8 system fault 34 internal bus c...

  • Page 28

    26 • vacon general data tel. +358 (0)201 2121 • fax +358 (0)201 212205 7 7. General data dimensions and weight frame height (mm) width (mm) depth (mm) weight (kg) mi1 160 66 98 0.5 mi2 195 90 102 0.7 mi3 254 100 109 1 supply network networks vacon 10 (400 v) cannot be used with corner grounded netwo...

  • Page 29

    General data vacon • 27 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 7 - the drive can be connected to the power supply with the above-mentioned fuses. The short circuit current of the power supply may not exceed 50 ka. - use cables with heat resistance of at least +70 °c. - the fuse...

  • Page 30

    28 • vacon general data tel. +358 (0)201 2121 • fax +358 (0)201 212205 7 vacon 10 power ratings *the maximum ambient operating temperature of this drive is +40°c! Mains voltage 208 - 240 v, 50/60 hz, 1~ series fre- quency converter type rated loadability motor shaft power nominal input cur- rent mec...

  • Page 31

    General data vacon • 29 24-hour support +358 (0)201 212 575 • email: vacon@vacon.Com 7 mains voltage 115 v, 50/60 hz, 1~ series fre- quency converter type rated loadability motor shaft power nominal input cur- rent mechanical size weight (kg) 100% continu- ous current i n [a] 150% over- load current...

  • Page 32

    30 • vacon general data tel. +358 (0)201 2121 • fax +358 (0)201 212205 7 note: the input currents are calculated values with 100 kva line transformer supply. Quick modbus setup mains voltage 600 v, 50/60 hz, 3~ series fre- quency converter type rated loadability motor shaft power nominal input cur- ...

  • Page 33

    Rev. ;& document id: manual authoring: documentation@vacon.Com vacon plc. Runsorintie 7 65380 vaasa finland subject to change without prior notice © 2012 vacon plc. Find your nearest vacon office on the internet at: www.Vacon.Com.